Technical Information - Wakol

WAKOL D 1680 Parquet AdhesiveTechnical informationArea of applicationDispersion-based adhesive according to DIN EN 14293 for the shear-resistant laying of• 10 mm solid wood lam parquet flooring, oak wood type, according to DIN EN 13227• mosaic parquet according to DIN EN 13488• on-edge lamella parquet according to DIN EN 14761, at least 16 mm thick,max. 200mm in length• strip parquet according to DIN EN 13226• multi-layer parquet according to DIN EN 13489• wood block RE / WE according to DIN 68702, single blocks fromat least 30 mm thicknesson very absorbent subfloors indoors.Special properties1) 2) 3)• solvent-free according to TRGS 610• corresponds to DIN EN 14293• suitable for underfloor heating• swelling-optimized1) Based on the criteria of GEV (Association for Emission-controlled Laying Materials), classified as EMICODE EC1 PLUS:very low in emissions2) Emissions-certified construction product i.a.w. DIBt principles: Wakol GmbH, 66954 Pirmasens, Z-155,10-13 ParquetAdhesive3) Emissions class according to French lawTechnical dataRaw material basis:Airing time:Open time:Ready to bear load:Surface treatment:Cleaning agent:synthetic resin dispersionnoneapprox. 15 - 20 minutesafter 12 - 24 hoursafter the original wood moisture level is attainedwater, before adhesive setspage 1 of 3

Storage temperature:Storage time:GISCODE:EMICODE according to GEV:not below +5°C, sensitive to frost12 months at room temperatureD1EC1 PLUSApplication method and consumption 4) :TKB B3 700 – 900 g/m² Solid wood, lam, mosaic and small-sized ready-to-layparquet flooringTKB B5 650 – 850 g/m² Large-sized ready-to-lay parquetTKB B11 900 – 1100 g/m² On-edge lamella, strip parquet, small-sized ready-to-layparquet and wood-block paving4) Consumption depends on the surface structure and absorbability of the subfloorSubfloorsThe subfloor and the climatic conditions of the room must meet the requirements of DIN18356. Subfloors must be level, very absorbent, permanently dry, solid, even and free fromcracks, dirt and adhesion-inhibiting substances.WAKOL D 1680 Parquet Adhesive may be used for directly laying mosaic parquet (cubedpattern) and multi-layer parquet (2-layer and 3-layer ready-to-lay parquet) on pre-primedcalcium sulphate concrete; other parquet types and laying parquet on non-absorbentsubfloors require application of a levelling compound with a layer thickness of at least 2 mm,depending on the absorbability of the levelling compound.Very absorbent subfloors (e.g. open-porous cement screeds) must be primed with WAKOL D3074 Primer Concentrate (1:2 water diluted) or WAKOL D 3073 Universal Primer. Ensure,that no film is left on the surface.Alternatively, for bonding to cast asphalt and calcium sulphate concrete, WAKOL MS 290Parquet Adhesive, WAKOL MS 260 Parquet Adhesive, firm-elastic, WAKOL MS 250 ParquetAdhesive, elastic, WAKOL MS 230 Parquet Adhesive, elastic, WAKOL PU 210 ParquetAdhesive, WAKOL PU 225 Parquet Adhesive or WAKOL PU 390 Parquet Adhesive can alsobe used, if the corresponding technical information is followed.UsageStir adhesive well before using. Using a notched trowel, apply uniformly on the subfloor,avoiding adhesive pools.Do not apply more adhesive than can be processed within the specified open time at theparquet. Immediately insert the parquet flooring and press down firmly. Ensure that theunderside of each wooden element is sufficiently coated with adhesive.Maintain expansion joints along all adjoining sections!O:\TI-GUELTIG\TI Bau\englisch\3235GB0108 0712 WAKOL D 1680.doc page 2 of 3Stand: 17.07.2012 Formular: F31TBGB, Revision: 4

ImportantDo not apply cement below a temperature of +15°C or above 65 % relative humidity. In coldweather, heat parquet flooring and adhesive beforehand in the room where they are to belaid.Strip parquet must not exceed a thickness-width ratio of 1:4 or a length of 600 mm.Solid wood lam parquet flooring must not exceed a thickness/width ratio of 1:5.Consult with the Application Technology Department before laying mosaic parquet in paralleland English block strip form on calcium sulphate concrete.For laying exotic parquet, wood block in laying units, 10 mm solid wood lam parquet flooringwith the wood types beech, ash and maple as well as for finished 1-layer parquet floorelements, use WAKOL MS 290 Parquet Adhesive, WAKOL MS 260 Parquet Adhesive, firmelastic,WAKOL PU 210 Parquet Adhesive, WAKOL PU 225 Parquet Adhesive or WAKOLPU 390 Parquet Adhesive while heeding the corresponding technical information.We guarantee the uniform high quality of our products. All data are based on tests and manyyears of practical experience and refer to standardised conditions. The variety of materialsused and the different construction site conditions, which lie beyond our control, preclude anyclaims based on this data. We therefore recommend making sufficient trials. Accompanyingflooring manufacturer's instructions and the currently applicable standards and codes mustbe observed. We gladly provide technical advice.The product data sheets can be found in their latest version at www.wakol.com.When this Technical Information bulletin dated 16.07.2012 is issued, all previous versionscease to be valid.O:\TI-GUELTIG\TI Bau\englisch\3235GB0108 0712 WAKOL D 1680.doc page 3 of 3Stand: 17.07.2012 Formular: F31TBGB, Revision: 4