TA 9640 Specification Sheet - T and A Supply Company, Inc.
TA 9640 Specification Sheet - T and A Supply Company, Inc.
TA 9640 Specification Sheet - T and A Supply Company, Inc.
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>TA</strong> <strong>9640</strong> <strong>Specification</strong> <strong>Sheet</strong>DESCRIPTION: <strong>TA</strong> 9460 ARCHITECTS CHOICE COVE BASE ADHESIVE<strong>TA</strong> <strong>9640</strong> is an acrylic adhesive that will not contribute to cove base staining or shrinkage. Exhibits fast tack <strong>and</strong>wet suction to hold on inner <strong>and</strong> outer corners. Use for all types of vinyl cove base (TV, TPR) <strong>and</strong> rubber covebase (TS, TPR).SURFACE PREPARATIONWall surfaces should be sound, dry, clean <strong>and</strong> porous. Remove vinyl or silicone treated wall covering <strong>and</strong>adhesives from the area that is to receive this adhesive. Cove base should be laid out flat, <strong>and</strong> the room, covebase <strong>and</strong> adhesive should be preconditioned at approximately 70° F for 24 hours prior to <strong>and</strong> after installation.For best adhesion with molded rubber cove base, wipe the back of the base with damp cloth, prior toinstallation.INSTRUCTIONSSpread the adhesive on the cove base with a 3/32" x 3/32" x 3/32" V-Notch trowel or cartridge gun, to leave anample amount of adhesive for the wall surface. The cove base can be set in place up to 30 minutes after theadhesive is spread. Press firmly to the wall <strong>and</strong> rub or roll to get a smooth, even bond. Check to see that theadhesive has proper transfer to the wall.PHYSICAL PROPERTIESBase:Acrylic LatexColor:Off WhiteConsistency: Heavy PasteOpen Time: Up to 30 minutesShelf Life: One year in unopened container at 70° F.Coverage: Up to 280 linear feet of 4" cove base per gallon.Other Features: Freeze-thaw stable to 10° F. Anti-microbial added.Flammability: Non-flammable. Meets Class 1 ratings as determined by ASTM E-84.Clean-Up: Use warm soapy water while adhesive is still wet. When dry, use Taylor Touchdown #9Adhesive Remover/Stripper.CAUTIONDO NOT take internally. If swallowed, DO NOT induce vomiting. Call a physician immediately. KEEP OUT OFREACH OF CHILDREN.WARRANTY INFORMATIONThis product is manufactured according to exacting quality control st<strong>and</strong>ards <strong>and</strong> is warranted to be free frommanufacturing defects. Defective material called to our attention within one year of manufacture will bereplaced. No guarantee, expressed or implied, is made regarding the performance of this product since themanner <strong>and</strong> conditions of application are beyond our control.T&A <strong>Supply</strong> <strong>Company</strong>, <strong>Inc</strong>., Kent, WA05/09/12
<strong>TA</strong> <strong>9640</strong>MATERIAL SAFETY DA<strong>TA</strong> SHEETSECTION I IDENTIFICATIONManufactured For:Address/Phone:T&A <strong>Supply</strong> <strong>Company</strong>, <strong>Inc</strong>.6807 S 216 th St, Bldg AKent, WA 98035253.872.3682Manufacturered By: W.F. Taylor Co., <strong>Inc</strong>.Address/Phone: 11545 Pacific Ave.Fontana, CA 92337951.360.6677Emergency Phone No.: 800.535.5053Manufacturer's Code Identification: <strong>TA</strong> <strong>9640</strong>Trade Name: <strong>TA</strong> <strong>9640</strong> Architects Choice Cove Base AdhesiveDate Revised: 03/04/11SECTION II HAZARDOUS INGREDIENTSNone per OSHA Regulation: 29 CFR 1910.1200SARA Title III Section 313 Chemicals: NoneNFPA HMISH = 1F = 0R = 0SECTION III PHYSICAL DA<strong>TA</strong>Boiling Point: No dataEvaporation Rate/Vapor Density: Same as water.Vapor Pressure: Same as waterLBS/GAL: 9.45 – 10.05Percent Volatile: 42 - 44 (by weight)Odor: MildColor: Off WhiteSECTION IV FIRE AND EXPLOSION HAZARD DA<strong>TA</strong>DOT Category: Not regulatedFlash Point: NoneLEL: N/AExtinguishing Media: None requiredUnusual Fire <strong>and</strong> Explosion Hazards: NoneSpecial Fire Fighting Procedures: NoneSECTION V HEALTH HAZARD DA<strong>TA</strong>Symptoms of Over Exposure:Inhalation: May irritate the respiratory tract.Eyes: May result in irritation.Skin: May result in irritation.Ingestion: May result in gastric disturbancesFirst Aid Procedures:Eyes: Flush with waterSkin: Wash with soap <strong>and</strong> waterInhalation: Remove to fresh air if neededSECTION VI REACTIVITY DA<strong>TA</strong>Stability: StableConditions to avoid: None known<strong>Inc</strong>ompatibility/Materials to avoid: None knownHazardous decomposition products: None knownHazardous polymerization: Will not occurSECTION VII SPILL OR LEAK PROCEDURESSteps to Be Taken if Material is Spilled: Keep out of sewersystems to prevent blockage due to polymer deposits. Useabsorbent material to collect <strong>and</strong>/or scrape up excess <strong>and</strong>place into closed DOT approved containers for disposal.Waste Disposal: Abide by all State, Federal <strong>and</strong> localregulations.SECTION VIII SPECIAL PROTECTION INFORMATIONRespiratory protection: None neededVentilation: Local exhaustProtective gloves: None required.Eyes: GogglesOther protective equipment: NoneSECTION IX SPECIAL PRECAUTIONSPrecaution for H<strong>and</strong>ling <strong>and</strong> Storing: Do not puncture,protect from freezing <strong>and</strong> excessive heat.KEEP OUT OF REACH OF CHILDRENT&A <strong>Supply</strong> <strong>Company</strong>, <strong>Inc</strong>., Kent, WA05/09/12
Change language