Technisches Merkblatt - FEYCO COATINGS

Technical Data SheetEffective: 11/07/2012Replaces edition dated: 15/03/2011Data Sheet No. 8650HYDROLAN Wischbeize (Wiping Stain)DescriptionProduct descriptionHYDROLAN Wischbeizen are ready-to-use, water-based, light-fast pigmentstains with a rustic stain effect (e.g. on oak and ash).Raw material baseArea of applicationStaining substances and waterFurniture and interiors as well as panelling when a rustic stain effect isrequired.Form of supply Colours 7 shades (can be mixed), as well as to customer specifications220 brown 224 blue221 yellow 225 black222 orange 226 white223 redGloss level -PackagingPlastic 1 5 lTechnical DataThe data apply for White. They can vary for other shades.Specific gravity (23 ºC) 1.3 g/cm³Solids content 40 ± 1 % by weightOrganic solvents 2 ± 1 % by weightVOC content (EU) 44 g/lShelf life at 20 °C 12 months in well-sealed original containersTheoretical coverage -- g/m² 7-8 m²/kg for -- µm dry coat thicknessSafety DataRefer to our Safety Data Sheet No. 865000as well as the instructions on the label.FEYCO AG, Hauptsitz, Industriestrasse 11, CH-9430 St. MargrethenPhone +41 71 747 84 11 Fax +41 71 747 85 10 www.feyco-coatings.comPage 1 of 3

Technical Data Sheet No. 8650 Page 2 of 3PreparationSubstrate Product DatasheetCoverage perapplication8650 Hydrolan Wischbeize 8650 1 x saturatedLacquer 1 x 120 - 150g/m2Intermediate sanding, grain 220 - 280Lacquer 1 x 120 - 150g/m2Surface preparationPlease contact our technical staff for further application suggestions.SubstrateWood substrate, untreatedEvery substrate must be clean, dry and free from grease and oil.Only apply stains to newly-sanded surfaces.Wood sanding, grain 150 / 180 (comply with sequence)ApplicationPersonal protectionWe recommend wearing protective clothing even in cases where no localregulations are in force.The precautions according to local regulations with respect to hygiene andequipment must be observed.StirringStir stains well before useDilutionIf necessary with water (produces lighter shade)Brush / spongeapplicationYes, apply evenly, then wipe off excess with absorbent cloth.RollingNoTrowel applicationNoFEYCO AG, CH-9430 St. Margrethen

Technical Data Sheet No. 8650 Page 3 of 3Viscosity Dilution Nozzle Pressure Spray coatsGravity feed gun - - 1.2 1-1.5bar1Apply evenly,then wipe offexcess withabsorbentcloth.Suction spray gun - - - - -UB paint gun - - - - -Airless (airmix) spraying - - - - -HVLP paint gun - - - - -EvaporationDrying timeFor -- µm dry film at 23 °C and 65 % relative humidityDust-dry after: 30 minutesTouch-dry after: 30 minutesRecoatable after: 3-4 hoursImportant InformationSpecial restrictionsBefore beginning staining work always make a test on the original wood. Theshade of a stain depends on several factors such as the wood characteristics,wood shade, sanded finish etc.Minimum application anddrying temperatureCoat removal -Equipment clean-up16 °C The temperature of the floor, air and material must not bebelow this temperatureImmediately with water, treat dried stains with cellulose thinner and rinsewith spirit polishThis data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guaranteesfor use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees.Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to technicalstandards, regulations and rules of the trade are the responsibility of the processor, even if our employee was on site during handling .Modifications due to technical developments may be made. The latest version of this information is applicable. In special cases, please requestseparate technical specifications.FEYCO AG, CH-9430 St. Margrethen