15533 Nifty HR12 - Facelift

More documents

Recommendations

Info

DRIVING CONTROLSSTOWED3) Only Low speed will be attainable regardless of position ofHi/Lo selector.4) Select drive joystick from hand lever controlsA Up for FORWARDSBCDDown for REVERSELeft for STEER LEFTRight for STEER RIGHTDO NOT OPERATE THE NIFTYLIFT WHILST ELEVATEDUNLESS ON A FIRM, LEVEL SURFACE FREE FROM ANYPOSSIBLE OBSTRUCTIONS OR HAZARDS BOTH ATGROUND LEVEL AND OVERHEAD.5) Control levers give a fully proportional response thereforethe more the lever is moved away from the centre OFFposition the faster the function will become.1) Check proposed route for possible hazards, obstructionsand personnel.2) Depress footswitch located in platform floor (if applicable).3) Use Hi/Lo selector on platform pushbutton control stationto determine speed. (See section Platform PushbuttonControls Station).HIGH DRIVE – GIVES HIGH SPEED AND LOW GRADEABLITYLOW DRIVE – GIVES LOW SPEED AND HIGH GRADEABILITY4) Select drive joystick from hand lever controls (see SectionPlatform control operation) andA Up for FORWARDSB Down for REVERSEC Left for STEER LEFTD Right for STEER RIGHT5) All control levers give a fully proportional response,therefore the more the lever is moved away from the centre(off) position the faster the function will become.6) Maximum drive speed is only attainable when all booms arefully stowed and the Hi/Lo selector is in the Hi position.7) When driving with the booms fully stowed, the tilt alarm isbypassed to allow the <strong>Nifty</strong>lift to be driven in areas wherethe slope exceeds the five degree working limit. In normaloperation the drive is therefore unaffected when drivenonto a slope in excess of five degrees until the booms areraised, whereupon the drive would be disabled and the tiltalarm sounds continuously.8) Under no circumstances should any <strong>Nifty</strong>lift SP seriesmachine be driven on slopes exceeding 25%, with thebooms fully stowed.ELEVATEDALL NIFTYLIFTS ARE FITTED WITH ATILT ALARM – PRE-SET IN THE FACTORY. ONCEENERGISED THE NIFTYLIFT WILL LOSE ALL POWERTO DRIVE FUNCTIONS AND A LOUD AUDIBLE ALARMWILL BE ACTIVATED. TO DE-ACTIVATE, LOWER THEBOOMS FULLY TO STOWED POSITION AND REPOSITION ON FIRM LEVEL GROUND.IF ALARM SOUNDS -DESCEND IMMEDIATELYAND RE- LEVEL MACHINE BASE.BOOM CONTROLSDO NOT OPERATE THE NIFTYLIFT WHILST ELEVATEDUNLESS ON A FIRM, LEVEL SURFACE FREE FROM ANYPOSSIBLE OBSTRUCTIONS OR HAZARDS BOTH ATGROUND LEVEL AND OVERHEAD.1) Never exceed the maximum platform as capacity as statedon identification plate.2) Check below, above and around platform for anyobstruction or hazards before operating any function.3) Depress the foot switch located in the platform floor(if applicable).4) Select hand lever controls marked 2,3,4,5,6 (see section:Platform Control OPeration)DO NOT OPERATE THE NIFTYLIFT WHILST ELEVATEDUNLESS ON A FIRM, LEVEL SURFACE FREE FROM ANYPOSSIBLE OBSTRUCTIONS OR HAZARDS BOTH ATGROUND LEVEL AND OVERHEAD1) Check proposed route for possible hazards, obstructionsand personnel.2) Depress footswitch located in platform floor (if applicable).IF ALARM SOUNDS – DESCEND IMMEDIATELY.THIS MACHINE IS NOT ELECTRICALLY INSULATED. DONOT WORK WITHIN 10FT (3M) OF OVERHEAD CABLESEXCEEDING 415 VOLTS.4
EMERGENCY CONTROLSNOTESGENERALCHECKING THE OPERATION OF THE EMERGENCYCONTROLS EVERY DAY AND/OR BEFORE EACH SHIFTIS AN ESSENTIAL PART OF THE OPERATORS DUTIES.The operator and all ground personnel must bethoroughly familiar with the location and operation of theEMERGENCY CONTROLS.IN THE EVENT OF AN INCAPACITATED OPERATOR.Turn key switch selector at ground control station to ground (i.e.fully down). Lower on ground controls as detailed under Section:Ground Control Operation.IN THE EVENT OF MACHINE FAILURE.If all machine power is lost, the Emergency Handpump can beused to provide the hydraulic power to manoeuvre the machine.Lower the platform using handlever controls in platform or atground control station.FOLLOWING AN EMERGENCY DESCENT RECOVERYOF THE PLATFORM, FULLY EXTEND AND RETRACTALL CYLINDERS FROM GROUND CONTROL STATIONBEFORE USING THE MACHINE.TO ROTATE PLATFORM IN AN EMERGENCY.Fit 1/2 inch drive socket on to end of slew worm gear and crankround manually.5
Page 4 and 5: HR12 with base telescope controlTEL
Page 8: 0800 52 15 95www.facelift.co.ukoper

15533 Nifty HR12 - Facelift

Create successful ePaper yourself

Delete template?

Save as template?