SSPA Remote Control Panel - General Dynamics SATCOM ...

SSPA Remote Control PanelRCP-2001IntroductionThe RCP-2001 allows you to easily monitor and control an Antenna-Mount solid-state power amplifier (SSPA) or othersingle-module SSPA from a remote location. The RCP-2001 enables the remote, real-time operation of a single SSPA,which is especially convenient for installations where the SSPA is located in an inaccessible or inconvenient location.Features• User-friendly menu structure for SSPA controlcommands and status display• Provides customer Serial I/O port (up to 28.8 kBps)• Audible alarm• Worldwide AC input capability• Can be located up to 1.3 km (4000') from SSPA withinexpensive cable• Compatible with all Antenna-Mount SSPAs withfirmware version 2.0x or higherPart Number/Ordering InformationRCP-2001Options1 Rack Slides3 Parallel I/O5 DC Power 24 V6 DC Power 48 VOrder cable ACAB-13135-X separately(where ‘X’ denotes length in feet, in 50 ftincrements).Front PanelONLINE 1RF ONRCP-2001PREVWARNINGGAINMODIFYMENUFAULTONLINE 2MUTESELFAULTRESETRear Panel85-264 V47-63 HzSERIAL I/OSSPA LINKAUXOPTION 3 PARALLEL I/OJ1J2RCP-2001VX.XXJ3J4FOR CONTINUED PROTECTION AGAINST FIRE,REPLACE ONLY WITH SAME TYPE AND RATINGOF FUSE.Connector InterfaceRef. Des. Function Connector Type Mating Connector CommentJ1 AC In IEC 320 IEC Cordset Standard" DC In 4-pin MS, Male 4-pin MS, Female Option 5 or 6J2 Serial I/O 9-pin D, Female 9-pin D, Male StandardJ3 SSPA Link 9-pin D, Male 9-pin D, Female StandardJ5 Parallel I/O 37-pin D, Male 37-pin D, Female Option 3

SpecificationsParameter Notes Min. Nom./Typ. † Max. UnitsPower Requirements Voltage, Standard 85 265 VacFrequency 47 63 HzPower 13.5 WVoltage, Option 5 20 32 VdcVoltage, Option 6 42 56 VdcOperating Temperature Range 0 +50 °CSSPA Link Cable Length 4000 (1.3) ft (km)Size 19 W x 1.72 H x 17.52 D inches482.6 x 43.7 x 445 mm†When there is only one value on a line, the Nom./Typ. column is a nominal value; otherwise it is a typical value. Typical values areintended to illustrate typical performance, but are not guaranteed.Parallel I/O (Option 3)The RCP-2001's parallel I/O (Option 3) provides eight independent contact-closure inputs and eight Form 'C' outputs.Each input or output is easily configured via the RCP-2001's front panel display and an extensive menu of SSPAcontrol and status monitoring options.Inputs *No functionUser Fault (Active High)User Fault (Active Low)MuteUn-MuteMute/Un-Mute ToggleMute (Low)/Un-Mute (High)RF Inhibit (Active Low)RF Inhibit (Active High)Fault ResetOutputs *No function (user-defined function)Output Power Fault (High or Low)Voltage FaultAny FaultRemote/Local ModeMaintenance ModeRF InhibitRF On/OffMute/OperateAny WarningAny Fault or WarningTemperature FaultCurrent FaultRatingsInputs:Contact closure to ground(5 V/5 mA)Outputs:Form 'C' dry contacts100 V/0.5 A/3 W maximum* Additional functions may be offered for SSPAs with optional hardware features.Other Products• Low Noise Amplifiers and LNA Systems• Solid-State Power Amplifiers and SSPA Systems• General Purpose Converters• Satellite Communications Equipment• Custom Subsystems60 Decibel Road, Suite 200 • State College, PA 16801 USA • Tel. 814 238 2700 • FAX 814 238 6589 12724 Rev. A ECR 7991 4/11/07 MDBWeb Site: www.gdsatcom.com/electronics.php© General Dynamics. All rights reserved. General Dynamics reserves the right to make changes to its products and specifications at any time and without notice.All trademarks indicated as such herein are trademarks of General Dynamics. All other product and service names are the property of their respective owners.