Waterous Product Catalog

SPLIT-SHAFT PUMPCM / CMUThe low profile split-shaft two-stage series/parallel pump with ball-type transfervalve allows you to switch from pressure to volume smoothly & easily.• Flame-plated impellers (standard on CMU, optional on CM)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings located outsidethe pump casing• Bronze double-hubbed accurately balanced impellers• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Adjustable BFG packing standard (spring-loaded mechanical seal available)• C20 Transmission consisting of an aluminum case and chain-driven forsilent operationSPLIT-SHAFT PUMPS• Maximum Pressure: 600 PSI (41 bar)SPLIT-SHAFT PUMPSA SPLIT-SHAFT FIRE PUMP FOR EVERY APPLICATION.Waterous split-shaft pumps provide fire industry professionals with easy-to-operate systems that offer the most efficient waterdelivery system on the market. Admired for their craftsmanship and exclusive design features, Waterous split-shaft pumps havebecome the primary firefighting tools of fire departments around the globe.SPLIT-SHAFT PUMPCS / CSUDesigned with a two-piece, horizontally split body with intake and dischargepassageways in a single casting and on the same level. This design provides thelowest possible height, a lower center of gravity, and more room for hose reels,GPMl/minl/secGPMl/minl/secCM FLOW500, 750, 1000, 12502000, 3000, 4000, 500030, 50, 65, 80CMU FLOW1500, 1750, 2000, 22506000, 7000, 8000, 9000100, 115, 130, 150PSI150PSI150CM PRESSUREBar kPa10 1000CMU PRESSUREBar kPa10 1000MPa1.0MPa1.0SPLIT-SHAFT PUMPShose beds and other equipment.SPLIT-SHAFT PUMP• Flame-plated impellers (standard on CSU, optional on CS)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings locatedoutside the pump casing• Bronze double-hubbed accurately balanced impeller• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Adjustable BFG packing standard (spring-loaded mechanical seal available)• C20 Transmission consisting of an aluminum case and chain-driven forsilent operation• Maximum Pump Pressure: 400 PSI (34 bar)CS FLOWCS PRESSUREGPM 750, 1000, 1250 PSI Bar kPa MPal/min 3000, 4000, 5000 150 10 1000 1.0l/sec 50, 65, 80CSU FLOWCSU PRESSURES101 COMPACTWith a smaller footprint than other larger, midship mounted fire pumps, the S101 Compactmeasures 26” from the front of the ram’s horn intake to the rear of the C20 transmission, whichsaves on compartment space for those important tools needed when fighting a fire.• Cast ductile iron body• Dual stripping edge volute• Passive lubrication system• Dual Intake Wye (Ram Horn)• Self-adjusting mechanical seal• Mechanically and hydraulically balanced impeller• Replaceable bronze wear rings• All deep-groove anti-friction ball bearings, oil-splash lubricated• Discharge: 5 in. ANSI flange or an optional 21st Century Manifold (4 in.end flanged manifold with (8) 2-1/2 in. side pads or an optional 5 in. ANSIto 4 in. ANSI adapter• C20 Transmission consisting of an aluminum case and chain-driven forsilent operation• 5-Year Limited WarrantyS101 COMPACT FLOWS101 COMPACT PRESSUREGPM1500, 1750, 2000, 2250PSIBarkPaMPaGPM1250, 1500, 1750, 2000PSIBarkPaMPal/min6000, 7000, 8000, 90001501010001.0l/min5000, 6000, 7000, 80001501010001.0l/sec100, 115, 130, 150l/sec80, 100, 115, 1305 6

SPLIT-SHAFT PUMPPTO-DRIVEN PUMPSS100Get the power and performance of a traditional midship fire pump in a compact,lightweight design. Made of ductile iron, the S100 are nearly 35% lighter, and yet 25%stronger than identical pumps made with gray iron. Available as a direct-engine mount ormatched with a Waterous aluminum case transmission.PUMPING ON THE GO.Provide true "pump and roll" capability while reducing transmission wear on your apparatus by adding a PTO fire pump to your firefightingarsenal. Available in multiple sizes and styles, Waterous has a PTO fire pump to fit your requirements and apparatus set-up perfectly.• Cast ductile iron bodyPTO-DRIVEN PUMP• Dual stripping edge volute• Passive lubrication systemCPK- 2• Self-adjusting mechanical sealThe CPK-2 is driven by a transmission side mounted PTO and is able to accommodate multiple lines• Mechanically and hydraulically balanced impellerfor straight stream or fog nozzles.• Replaceable bronze wear rings• All deep-groove anti-friction ball bearings, oil-splash lubricated• 5-inch ANSI flange or optional end flanged discharge manifold• C20 Transmission consisting of an aluminum case and chain-drivenfor silent operation• 5-Year Limited Warranty• High tensile, close-grained gray iron casing (bronze/gunmetal optional),one-piece volute body• 17-4 stainless steel, heat-treated impeller shaft (monel shaft optional)• Bronze double-hubbed precision-balanced impeller• 3-inch (76.2mm) NPT or BSP intake; 2-inch (50mm) NPT or BSP discharge(BSP threads available straight or tapered)SPLIT-SHAFT PUMPSSPLIT-SHAFT PUMPCX / CXS SeriesS100 FLOWS100 PRESSUREGPM 1250, 1500, 1750, 2000 PSI Bar kPa MPal/min 5000, 6000, 7000, 8000 150 10 1000 1.0l/sec 80, 100, 115, 130The most versatile pump offered by Waterous. When you need the performance of a largersplit-shaft pump, but just don’t have the compartment space, the CX/CXS is the answer.• Multiple gearbox mounting positions (horizontally, vertically or inverted)• Seven optional speed-increasing transmission ratios• Crown-shaved, carburized and hardened helical cut, constant-mesh quiet gears• K Transmission consists of a close-grained, gray iron casing with constant-mesh,stainless steel helical gears• 5-year Limited WarrantyMAXIMUM FLOWMAXIMUM PRESSUREGPMCPK-2 PERFORMANCEL/min L/sec PSI150400Bar1028kPa10002800300 1100 1860 200 3MPa1.02.8• Cast ductile iron bodyPTO-DRIVEN PUMP• Dual stripping edge volute• Passive lubrication systemCPK- 3• Self-adjusting mechanical seal• Mechanically and hydraulically balanced impeller• Replaceable bronze wear rings• All deep-groove anti-friction ball bearings, oil-splash lubricated• 5-inch ANSI flange or optional end flanged discharge manifold• C20 Transmission consisting of an aluminum case and chaindriven for silent operation• 5-Year Limited WarrantyCXC20 / CXSC20 FLOWCX / CXS PRESSUREGPM 750, 1000, 1250, 1500* PSI Bar kPa MPaA compact two-stage pump with “pump and roll” capability making it ideal for extinguishing grass andbrush fires.• High tensile, close-grained gray iron casing (bronze/gunmetal optional),one-piece volute body• Bronze double-hubbed, precision-balanced impellers• Separable impeller shaft for ease of serviceability• Push-pull manual bronze transfer valve• Available in either rotation of input shaft• 4-inch (101.4mm) NPT tee adapter intake; two 2-inch (50mm)or 2.5-inch (64mm)NPT tee adapter (or 2.5-inch (64mm) tapped flange) dischargePTO-DRIVEN PUMPSl/min3000, 4000, 5000, 6000*1501010001.0• K Transmission consists of a close-grained, gray iron casing withl/sec 50, 65, 80, 100***Using both sides of the “Ram Horn” styleintake fitting (CXSC20 Models Only)constant-mesh, stainless steel helical gears• Seven optional speed-increasing transmission ratios• 5-year Limited WarrantyCPK-3 PERFORMANCEGPML/minL/secPSIBarkPaMPaMAXIMUM FLOW500 2000 331501010001.0MAXIMUM PRESSURE60 200 38005555005.57 8

PTO-DRIVEN PUMPCMK / CMUKCMPA / CMUPAPTO-DRIVEN PUMPCSK / CSUKCSPA / CSUPAThe low profile two-stage series/parallel pump with ball-type transfervalve allows you to switch from pressure to volume smoothly & easily.PTO-DRIVEN PUMPSThe leading single-stage split-shaft fire pump on the market today provides efficient useof power and performance. Designed with a two-piece, horizontally split body withintake and discharge passageways in a single casting and on the same level, thispump provides the lowest possible height, a lower center of gravity, and more roomfor hose reels, hose beds and other equipment.• Flame-plated impellers (standard on CSU, optional on CS)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings locatedoutside the pump casing• Bronze double-hubbed accurately balanced impeller• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Adjustable BFG packing standard (spring-loaded mechanical seal available)• Available with K Series or PA Series Transmissions• K Series consists of a close-grained, gray iron casing andconstant-mesh helical gears• PA Series consists of an aluminum case and is chain driven for silent operation• Flame-plated impellers (standard on CMU, optional on CM)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings located outsidethe pump casing• Bronze double-hubbed accurately balanced impellers• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Adjustable BFG packing standard (spring-loaded mechanical seal available)• Available with K Series or PA Series Transmissions• K Series consists of a close-grained, gray iron casing andconstant-mesh helical gears• PA Series consists of an aluminum case and is chain driven for silent operationCM FLOWCM PRESSUREGPM 500, 750, 1000, 1250 PSI Bar kPa MPal/min 2000, 3000, 4000, 5000 150 10 1000 1.0l/sec 30, 50, 65, 80PTO-DRIVEN PUMPSGPMl/minl/secCS FLOW750, 1000, 12503000, 4000, 500050, 65, 80PSI150CS PRESSUREBar kPa10 1000MPa1.0GPMl/minl/secCMU FLOW1500, 1750, 2000, 22506000, 7000, 8000, 9000100, 115, 130, 150PSI150CMU PRESSUREBar kPa10 1000MPa1.0CSU FLOWCSU PRESSUREGPM1500, 1750, 2000, 2250PSIBarkPaMPal/min6000, 7000, 8000, 90001501010001.0l/sec100, 115, 130, 15011 12

REAR-MOUNT FIRE PUMPSTHE LITTLE PUMPS THAT PACK A MIGHTY PUNCH.Specifically designed for international-style fire vehicles, the compact, rear-mounted simultaneous High/Low pressure series pumps feature builtinhigh-pressure relief valves for enhanced safety. All HL models are backed by an industry exclusive 5-Year Limited Warranty.REAR-MOUNT FIRE PUMPHL400• Corrosion-resistant anodized aluminum or bronze body (gunmetal)• Wear-resistant anodized aluminum, flame-plated hubs Low Pressure Impeller• Bronze High Pressure Impeller• Stainless Steel Impeller Shaft• Bronze Wear Ring• Maintenance-free mechanical seal• Available with K Gear Drive Transmission• Available in Clockwise or Counterclockwise rotation (not available on bronze models)• Constructed of anodized aluminum, the pedestal supports the Waterous automatic pistonprimer and main bearings.• Anodized aluminum or bronze Intake with 30°droop, two auxiliary 4” side flanges• HL400 available with 6 in. BSP, 5 in. Victaulic® connection, 150 mm Storz® or 4 in. BSP dual intake• Anodized aluminum or bronze discharge manifold with six discharge outlets(2) Anodized aluminum non-return discharge valve (Low Pressure)• Interstage Crossover Valve: The valve incorporates both a built-in high pressure reliefvalve and a removable strainer for the high pressure stage inlet• 275 lbs (125 kg).HL400 FLOWGPM L/min L/secHIGH 100 400 6.5REAR-MOUNT FIRE PUMPLOW 1000 4000 65HL400 PRESSUREPSI600150Bar4010kPa40001000MPa4.01.0REAR-MOUNT FIRE PUMPPASSPORT S200 MODELThe S200 fire pump was designed by Waterous engineers to provide the utmost quality and reliability that comes with the Waterous name. With thegoal of reaching international standards, the S200 accomplished that goal by meeting EN 1028, NFPA 1901 (North America) and CCC in China. TheS200 is quieter, lighter and more flexible than any other fire pump on the market today. You can rest assured that the dependability and quality ofthe S200 is guaranteed by a 5-Year Limited Warranty.PASSPORT (S200) PERFORMANCEGPM L/min L/sec PSI Bar kPa MPaNFPA 1901,500 2000 33 150 10 1000 1.0EN1028 and500 2000 33 225 15 1500 1.5CCC Ratings750 3000 50 150 10 1000 1.0750 3000 50 225 15 1500 1.5HL300Key Factors:• Maintenance-free (oil-free primer and self-lubricated bearings)• Available in mid-mount configuration• Optional round-the-pump foam system• Available with K Series gear-drive transmission• Available in clockwise or counterclockwise• Built-in automatic primers• Weighs less than 200 lbs. (91 kg).• Optional operator’s panel• Optional Storz fittings• Bronze/gunmetal construction availablerotation (not available on bronze models)• 5-Year Limited Warranty• 245 lbs (111 kg)Volute Body and Head:Bronze with lightweight composite materialsPriming:Integrated, fully automatic, oil and maintenance-free piston primer withREAR-MOUNT FIRE PUMPSHIGHLOWREAR-MOUNT FIRE PUMPHL200HL300 FLOWHL300 PRESSUREGPM L/min L/sec PSI Bar kPa MPa100 400 6.5600 40 4000 4.0750 3000 60150 10 1000 1.0• Available in mid-mount configuration• Optional round-the-pump foam system• Optional operator’s panel• Optional Storz fittings• Bronze/gunmetal construction available• Available with K Series gear-drive transmission• Available in clockwise or counterclockwiserotation (not available on bronze models)• 5-Year Limited Warranty• 235 lbs (107 kg)HL200 FLOWHL200 PRESSUREGPM L/min L/sec PSI Bar kPa MPaHIGH 100 400 6.5600 40 4000 4.0LOW 500 2000 33150 10 1000 1.0Impeller:Bronze impellers are standardImpeller Shaft:Consists of an impeller mounted on a stainless steel shaft with selflubricatedsealed bearings.Shaft Seal:The mechanical seal consists of a flat, highly polished (lapped), selfadjusting(spring-fed) carbon ring that is sealed in the pump body. Thecarbon ring presses against a highly-polished rotating ring that issealed to and rotates with the impeller. Mechanical seal is retained inand easily removable seal housing.Pedestal (Primer Housing):The pedestal is constructed of anodized aluminum and supports thepiston primers and main bearings. Contains no oil. Maintenance isnot required.50% more capacity than a typical piston primer. All components areconstructed of corrosion-resistant materials.Thermal Relief Valve:The thermal relief valve opens as the temperature of the water insidethe pump reaches 49° C. The valve opens and diverts water to one ofthe following locations:• To the holding tank, vehicle tank or to atmosphere (ground).Bearings:The main pump shaft uses long-life, double-row angular contact ballbearing and a single-row ball bearing that are self-lubricated, doublesealedand require no maintenance.REAR-MOUNT FIRE PUMPS13 14

DIRECT-ENGINE MOUNT PUMPSDIRECT-ENGINE MOUNTED PUMPSCPT- 2DIRECT-ENGINE MOUNTED PUMPSCPT- 3DIRECT-ENGINE MOUNTED PUMPSCPT- 4DIRECT-ENGINE MOUNT PUMPSThe CPT-2 is powered by directly mounting to an engine using an SAE bellhousing. Pumps are alsoable to accommodate multiple lines for straight stream or fog nozzles.• High tensile, close-grained gray iron casing (bronze/gunmetal optional),one-piece volute body• 17-4 stainless steel, heat-treated impeller shaft (monel shaft optional)• Bronze double-hubbed precision-balanced impeller• 3-inch (76.2mm) NPT or BSP intake; 2-inch (50mm) NPT or BSP discharge(BSP threads available straight or tapered)• T Series Transmission consists of a close-grained, gray iron casing withconstant-mesh, stainless steel helical gears• Multiple gearbox mounting positions (horizontally, vertically or inverted)• Several optional speed-increasing transmission ratios• 5-year Limited WarrantyMAXIMUM FLOWMAXIMUM PRESSUREGPMCPT-2 PERFORMANCEL/min L/sec PSI Bar kPa MPa300 1100 18 150 10 1000 1.060 200 3 400 28 2800 2.8A compact two-stage pump with “pump and roll” capability making it ideal for extinguishing grass andbrush fires.• High tensile, close-grained gray iron casing (bronze/gunmetal optional),one-piece volute body• Bronze double-hubbed, precision-balanced impellers• Separable impeller shaft for ease of serviceability• Push-pull manual bronze transfer valve• Available in either rotation of input shaft• 4-inch (101.4mm) NPT tee adapter intake; two 2-inch (50mm) or 2.5-inch (64mm)NPT tee adapter (or 2.5-inch (64mm) tapped flange) discharge• T Series Transmission consists of a close-grained, gray iron casingwith constant-mesh, stainless steel helical gears• Several optional speed-increasing transmission ratios• 5-year Limited WarrantyMAXIMUM FLOWMAXIMUM PRESSUREGPMCPT-3 PERFORMANCEL/min L/sec PSI Bar kPa MPa500 2000 33 150 10 1000 1.060 200 3 800 55 5500 5.5DIRECT-ENGINE MOUNTED PUMPSThe single stage design with vertically-split volute and pump transmission provides simpleoperation, easy maintanence and high reserve capacity.• High-tensile, close-grained gray iron (bronze/gunmetal optional), two-piece, vertically-split volute body• 17-4 stainless steel, heat-treated impeller shaft• Fully-enclosed, bronze, double-hubbed impeller with flame-plated hubs• Victaulic®, threaded or flanged intake connections• Self-adjusting corrosion- and wear-resistant mechanical seals• T Series Transmission consists of a close-grained, gray iron casing w/ constant-mesh, stainlesssteel helical gears• 5-year Limited Warranty• High-tensile, close-grained gray iron (bronze/gunmetal optional), one-piece volute body• 17-4 stainless steel, heat-treated impeller shaft• Bronze, double-hubbed, precision-balanced impellerAn ultra high-pressure, lightweight, 4-stage centrifugal pump. Able to produce high-pressure• Maintenance-free, self-adjusting shaft sealfog while the pumper is in motion or stationary.• Choice of 4-inch (101.4mm) NH or BSP threaded-end intake• T Series Transmission consists of a close-grained, gray iron casing• Ni-resist; special “stepped” designed wear rings reduce internal leakage & increase efficiencywith constant-mesh, stainless steel helical gears• Bronze, hydraulically and mechanically balanced impellers• 5-year Limited WarrantyCLT PERFORMANCE• Impeller hubs are “stepped” to minimize internal bypassGPM L/min L/sec PSI Bar kPa MPa• High-tensile, close-grained gray iron (bronze/gunmetal optional), two-piece,MAXIMUM FLOW 500 2000 33 150 10 1000 1.0horizontally-split volute body• Adjustable braided flexible graphite (BFG) packing• Available with either clockwise or counter-clockwise rotationCPT-4 PERFORMANCEof input shaftGPM L/min L/sec PSI Bar kPa MPa• T Series Transmission consists of a close-grained, gray ironcasing with constant-mesh, stainless steel helical gears60 200 3 1000 70 7000 7.015 16C GTDIRECT-ENGINE MOUNTED PUMPSC XTA single-stage end suction pump that is direct-engine mounted via a T Series Transmission.• High-tensile, close-grained gray iron (bronze/gunmetal optional),two-piece, vertically-split volute body• 17-4 stainless steel, heat-treated impeller shaft• Fully-enclosed, bronze, double-hubbed, precision-balanced impeller• Bronze replaceable wear rings• Self-adjusting corrosion- and wear-resistant mechanical seals• Optional crosspipe intake fitting allows for maximum flow of 1500 GPM (5700 L/min)• T Series Transmission consists of a close-grained, gray iron casingwith constant-mesh, stainless steel helical gears• 5-year Limited WarrantyDIRECT-ENGINE MOUNTED PUMPSC LTMAXIMUM FLOWMAXIMUM PRESSUREMAXIMUM FLOWCGT PERFORMANCEL/min L/sec PSI Bar kPa MPa750 3000 50 150 10 1000 1.080 300 5 350 24 2400 2.4One-piece design featuring intake and discharge arrangements in a wide variety of options to meet your requirements.GPMGPMCXT PERFORMANCEL/min L/sec PSI Bar kPa MPa1500 6000 100 150 10 1000 1.0DIRECT-ENGINE MOUNT PUMPS

DIRECT DRIVEN PUMPCMD / CMUDThe low profile midship two-stage series/parallel pump with ball-type transfervalve allows you to switch from pressure to volume smoothly & easily.• Flame-plated impellers (standard on CMU, optional on CM)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings located outsidethe pump casing• Bronze double-hubbed accurately balanced impellers• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Adjustable BFG packing standard (spring-loaded mechanical seal available)CMD FLOWCMD PRESSUREGPM500, 750, 1000, 1250PSIBarkPaMPaDIRECT-DRIVEN PUMPSA FIRE PUMP FOR EVERY APPLICATION.Waterous Direct Driven pumps provide fire industry professionals with easy-to-operate systems that offer the mostefficient water delivery system on the market. Admired for their craftsmanship and exclusive design features, WaterousDirect Driven pumps have become the primary firefighting tools of fire departments around the globe.DIRECT DRIVEN PUMPCSD / CSUDDIRECT-DRIVEN PUMPSThe leading single-stage split-shaft fire pump on the market today is available as a directdrive pump providing efficient use of power and performance. Designed with a two-DIRECT DRIVEN PUMPS100 / S100Dl/minl/secGPMl/minl/sec2000, 3000, 4000, 500030, 50, 65, 80CMUD FLOW1500, 1750, 2000, 22506000, 7000, 8000, 9000100, 115, 130, 150150 10 1000 1.0CMUD PRESSUREPSI150Bar10kPa1000MPa1.0DIRECT-DRIVEN PUMPSpiece, horizontally split body with intake and discharge passageways in a singlecasting and on the same level, this pump provides the lowest possibleheight, a lower center of gravity, and more room for hose reels, hosebeds and other equipment.Get the power and performance of a traditional midship fire pump in a compact,lightweight direct-engine mounted pump. Made of ductile iron, the S100D is nearly35% lighter, and yet 25% stronger than identical pumps made with gray iron.• Cast ductile iron body• Flame-plated impellers (standard on CSU, optional on CS)• Two-piece, horizontally-split, high-tensile strength cast iron pump casing• Optional bronze/gunmetal pump casing• All deep-groove oil and grease lubricated ball bearings locatedoutside the pump casing• Bronze double-hubbed accurately balanced impeller• Stainless steel separable impeller shaft• Replaceable bronze impeller rings• Flinger rings mounted on impeller shaft• Dual stripping edge volute• Passive lubrication system• Self-adjusting mechanical seal• Mechanically and hydraulically balanced impeller• Replaceable bronze wear rings• All deep-groove anti-friction ball bearings, oil-splash lubricated• 5-inch ANSI flange or optional end flanged discharge manifold• 5-Year Limited Warranty• Adjustable BFG packing standard (spring-loaded mechanical seal available)CS FLOWCS PRESSUREGPM 750, 1000, 1250 PSI Bar kPa MPal/min 3000, 4000, 5000 150 10 1000 1.0l/sec 50, 65, 80S100DGPMl/minl/secS100 FLOW1250, 1500, 1750, 20005000, 6000, 7000, 800080, 100, 115, 130PSI150S100 PRESSUREBar kPa10 1000MPa1.0CSU FLOWCSU PRESSUREGPM1500, 1750, 2000, 2250PSIBarkPaMPal/min6000, 7000, 8000, 90001501010001.0l/sec100, 115, 130, 15017 18

WATEROUS CAFSystemsCAFSystemsECLIPSE THE WORLD'S MOST TRUSTED CAFS.Used by more fire departments around the world than any other CAFSystem, the Eclipse CAFSystem from Waterous is easy tooperate, incredibly efficient and a proven performer. The Eclipse CAFSystem buttresses your attack capabilities with big flow ratesup to 2,250 GPM, high pressure up to 150 PSI and impressive suppression results.CAFSystemsONE STEP CAFSYSTEMPERFECT FOAM. EVERY TIME.• Encapsulated compressor with fewer hose, less noise and the ability to shiftin and out as needed while the pump is in use• Electric Auto-Sync balancing system to match air and water pressure• Available with Advantus® foam proportioner• Free onsite product orientation• 5-year Limited WarrantyWhen it comes to compressed air foam systems, nothing can match the ease of use ofthe ONE STEP CAFSystem. ONE STEP incorporates a powerful integrated midshipmountedair compressor system and revolutionary compact foam generators to providea reproducible homogenous, micro-cellular, continuous bubble stream. A characteristicof each ONE STEP CAFSystem is the pre-set flow rate and pre-set pressure for water andair. The operator does not have to adjust flows and pressures.WATEROUS CAFSystemsWATEROUS SPLIT-SHAFT PUMPThe ONE STEP CAFSystem is currently availableon Waterous CS, CSU and CMU midship pumpswith split-shaft transmissions.• CS, CSU, CMU150-OS GHH RAND AIR COMPRESSOR• 150 SCFM (4.25 m 3 /min)• Quiet, efficient and dependable rotary screwair compressor• Toothed-belt drive requires no lubricationor maintenanceAQUIS 2.5 FOAM PROPORTIONER• 2.5 GPM ( 9.5 l/min) @ 150 PSI (10 bar)• Exceeds NFPA 1901 requirements forproportioning accuracy• Pre-plumbed and pre-mountedONE STEP COMPACT FOAM GENERATORA characteristic of each ONE STEP CAFSystem isthe pre-set flow rate and pre-set pressure forwater and air. The operator does not have toadjust flows and pressures.ONE STEP CAFSystem uses a stand-alone“Compact Foam Generator” (CFG) for eachsimultaneously operated discharge outlet. Three2” Foam Generators are standard. These arespecially developed and patented devices in which• 80% of water content in the foam iseffectively used for fire fighting• Improved firefighter safety• Faster knockdown time• Less property damage• Less water usedthe ONE STEP extinguishing agent will begenerated. These foam generators include allnecessary elements such as:• Volume flow regulation of water and air• Volume flow limitations of water and air• Non-return valves for water and air• Mixing chamber• Mixing pressure control valve• Wet-dry changeoverl/minl/secPSI150CAFSystemsCS FLOWGPM 750, 1000, 1250ECLIPSE ES3000, 4000, 500050, 65, 80CS PRESSUREBar kPa MPa10 1000 1.0CSU FLOWCSU PRESSUREGPM 1500, 1750, 2000, 2250 PSI Bar kPa MPal/min 6000, 7000, 8000, 9000 150 10 1000 1.0l/sec 100, 115, 130, 150CMU FLOWCMU PRESSUREGPM 1500, 1750, 2000, 2250 PSI Bar kPa MPal/min 6000, 7000, 8000, 9000 150 10 1000 1.0l/sec 100, 115, 130, 150BIG SUPPRESSION. SMALL PACKAGE.The Eclipse ES compressed air foam system is proof that you can still get serious powerout of a tiny package. Unmatched in the industry for performance and versatility, the EclipseES is available in multiple configurations to fit your needs while providing unmatched fireextinguishing capabilities.• Available in three different models• Compatible with S100, CX and TC20 Series PTOS100 FLOWS100 PRESSUREGPM 1250, 1500, 1750, 2000 PSI Bar kPa MPal/min 5000, 6000, 7000, 8000 150 10 1000 1.0WATEROUS CAFSystemsSMARTPANEL CONTROL SYSTEMl/sec80, 100, 115, 130• 7” SMARTPANEL Control System• Engages Pump and Compressor• Engages the ONE STEP CAFSystem• Select from Dry or Wet Foam• Monitor Intake and Discharges• Monitor Engine / Pump PerformanceGPMl/minl/secCX FLOW750, 1000, 1250, 1500*3000, 4000, 5000, 6000*50, 65, 80, 100*PSI150CX PRESSUREBar kPa10 1000MPa1.019 20

PRE-SET FLOW RATEPRE-SET PRESSURE FOR WATER AND AIRNO OPERATOR ADJUSTMENTS NEEDED DURING OPERATIONWATEROUS CAFSystems MODULAR SLIDE-INModular Slide-InModular Slide-In70-35-GP• Briggs and Stratton Vanguard two-cylinder,air-cooled, four-cycle engine• 23 HP (17.2 kW)• Fire Troll 1.5 Foam Proportioner standard70-35-GP FLOWGPM 70l/min 265l/sec 4.4100-50-OS• Deutz 29.9 HP (22.4 kW) diesel engine• Waterous CPD-2 Pump• Waterous ONESTEP CAFSystemTwo 1-1/2" Compact Foam GeneratorsONE STEP CAFSystem is the pre-set flowrate and pre-set pressure for water and100-50-OS FLOWModular Slide-In100-50-DSSCFMM 3 /min35.970-35-GP PRESSUREPSI Bar kPa MPa100 6.9 690 .69air. The operator does not have to adjustflows and pressures during operation.• 7" SMARTPANEL Control System• One button engages fire pump, foamproportioner and CAFSystem• Easily select Wet or Dry Foam• GHH Rand 50 sCFM (1.4 m3/min) compressor• Stainless Steel Frame• Aquis 1.5 Foam ProportionerPSIGPM 100l/min 400l/secSCFMM 3 /minBarkPa6.5501.42100-50-OS PRESSUREMPaWATEROUS CAFSystems MODULAR SLIDE-INModular Slide-In200-100-DS• Duetz 29.9 HP (22.4 kW) diesel-fueled engine• Waterous CPD-2 Pump• GHH Rand 100 sCFM compressor• Stainless Steel Frame• Aquis 1.5 Foam Proportioner• Rotary Dial Foam Proportioning Rate Panel• Optional Operator Interface Terminal (OIT)for selecting foam proportioning ratesWATERAIR• Duetz 60.6 HP (45.2 kW) diesel-fueledengine• Waterous CPD-2 Pump• GHH Rand 100 sCFM compressor• Stainless Steel Frame• Aquis 1.5 Foam Proportioner• Rotary Dial Foam Proportioning Rate Panel• Optional Operator Interface Terminal (OIT)for selecting foam proportioning rates100-50-DS FLOWGPMl/min100400l/secSCFMM 3 /min6.5501.42100-50-DS PRESSUREPSI Bar kPa MPa100 6.9 690 .69125 8.6 860 .86200-100-DS FLOWGPM 200l/min 800l/secSCFMM 3 /min131002.83200-100-DS PRESSUREModular Slide-In200-100-OSWATER 150 10 1000 1.0AIR 125 8.6 860 .86• Duetz 60.6 HP (45.2 kW) diesel-fueled engine• Waterous CPD-2 Pump• Waterous ONESTEP CAFSystemTwo 1-1/2" Compact Foam Generators200-100-OS FLOWONE STEP CAFSystem is the pre-set flowrate and pre-set pressure for water andair. The operator does not have to adjustflows and pressures during operation.• 7" SMARTPANEL Control System• One button engages fire pump, foamproportioner and CAFSystem• Easily select Wet or Dry FoamGPMl/minl/secSCFMM 3 /min200800131002.83• GHH Rand 100 sCFM (2.83 m3/min) compressor 200-100-OS PRESSURE• Stainless Steel Frame• Aquis 1.5 Foam ProportionerPSI Bar kPa MPaWATER 150 10 1000 1.0AIR 125 8.6 860 .86WATEROUS CAFSystems MODULAR SLIDE-INPSI Bar kPa MPaWATER 150 10 1000 1.021 AIR 125 8.6 860 .8622

INTEGRATED PUMP / COMPRESSOR SYSTEMSPTO-DRIVEN AIR COMPRESSOR KITSINTEGRATED PUMP / COMPRESSOR SYSTEMSINTEGRATED PUMP / COMPRESSOR SYSTEMSPTO-DRIVEN AIR COMPRESSOR KITS500-80-P 80-P / 140-P / 200-PUNIFIED IN THE FIGHTPart pump, part compressor, all CAFS fire suppressing power. Waterous has several PTO-drivenIntegrated Pump/Compressor Systems available to meet your department’s needs. Thesemodels deliver everything you’d expect in a CAFS unit, including the ability to discharge water, foamsolution and compressed air for pneumatic tools. They also include a GHH Rand rotary screw airendwith poly-chain.• CLVK water pump and transmission• Auto Sync panel control• Compressor temperature gauge• 3-inch NPT discharge• GHH Rand rotary screw compressor• 5-year warranty• 4-inch Victaulic intakeWATER FLOWAIR FLOWPRESSUREGPM L/min L/sec500-80-P PERFORMANCESCFMm3/minPSI Bar kPa MPa500 2000 33 150 10 1000 1.080 2.3 125 8.6 860 .86PTO-DRIVEN. FIELD PROVEN.When you consider that a good PTO driven air compressor system is worth itsweight in gold, it’s hard to imagine the value of a Waterous PTO kit to yourfire department. Waterous offers three models available as OEM installationor retrofit. These CAFSystems are water-cooled and designed to dischargewater, foam solution or compressed air. They come with a GHH Rand rotaryscrew airend with integral speed increasing gear set, a 1013 shaft yoke andfree on-site orientation. What’s more, all units are available with Advantus®Foam Systems or Aquis Foam Proportioners and come with an industryexclusive 5-year warranty.Premium Quality PTO-Driven AirCompressor KitsSAIR FLOWCFM m3/min80 2.3PSI125PRESSUREBar kPa8.6 860MPa0.86PTO-DRIVEN AIR COMPRESSOR KITS500-120-P PERFORMANCE140 3.9125 8.6 860 0.86500 2000 33 150 10 1000 1.0200 5.6125 8.6 860 0.86120 3.4 125 8.6 860 .86500-150-P PERFORMANCE500 2000 33 150 10 1000 1.0150 4.25 125 8.6 860 .86Additional models available:INTEGRATED PUMP / COMPRESSOR SYSTEMS750-100-P / 1000-100-P / 1250-100-P750-150-P / 1000-150-P / 1250-150-P• Waterous CXVK Pump• Auto-Sync Control Panel• Compressor Temperature Gauge• 6-inch Victaulic Intake• 4-inch ANSI Discharge• Available with Advantus Foam Systems orAquis Foam Proportioner• 100 sCFM (2.83 m3/min)• Waterous CXVK Pump• Auto-Sync Control Panel• Compressor Temperature Gauge• 6-inch Victaulic Intake• 4-inch ANSI Discharge• Available with Advantus Foam Systems orAquis Foam Proportioner• 150 sCFM (4.3 m3/min)23 24

FOAM MANAGEMENT SYSTEMSFOAM PROPORTIONERSFOAM SYSTEMSWE PACKED THE FEATURES IN,SO YOU COULD PUT THE FIRES OUT.It takes more than concentrate and water to create the world’s most effective fire suppressing foam. Itdemands world-class engineering coupled with breakthrough technology to get it right. In other words, ittakes Advantus ® , the world’s most advanced foam system.• Foam Pump: Positive Displacement Pump• Available with A-B selector valve• Pump Motor: 1/2 HP (.40 kW)• 2-year warrantyFOAM PROPORTIONERSADVANTUS ® 3 AQUIS 1.5THE PERFECT BLEND OF PERFORMANCEAND VALUE.It’s not easy to properly proportion fire-suppressing Class A foam. To get the ratios right, you need tocompensate for a number of variables. Doing so demands world-class engineering coupled with dependable flowmeter technology. In other words, you need The Aquis Foam Proportioner from Waterous. It delivers a level ofperformance and reliability typically reserved for more expensive Class A foam proportioners.• Foam Pump: positive displacement plunger pump• Pump Motor: 1/3 HP ( .27 kW)• 1-year warrantyFOAM OUTPUTPRESSUREFOAM OUTPUTPRESSUREFOAM SYSTEMSFOAM SYSTEMSADVANTUS ® 6GPM L/min L/sec PSI Bar3 11.3 .18150 10MAXIMUM OPERATING PRESSUREPSI Bar kPa MPa450 32 3200 3.2kPa1000MPa1.0FOAM PROPORTIONERSAQUIS 2.5GPM L/min L/sec PSI Bar1.5 5.7 .1150 10MAXIMUM OPERATING PRESSUREPSI Bar kPa MPa450 32 3200 3.2kPa1000MPa1.0FOAM PROPORTIONERS• Foam Pump: Positive Displacement Pump• Available with A-B selector valve• Pump Motor: 1/2 HP (.40 kW)• 2-year warranty• Foam Pump: positive displacement plunger pump• Pump Motor: 1/2 HP ( .40 kW)• 1-year warrantyFOAM OUTPUTPRESSUREFOAM OUTPUTPRESSUREGPML/minL/secPSIBarkPaMPaGPML/minL/secPSIBarkPaMPa6 22.6 .361501010001.02.5 9.5 .161501010001.0MAXIMUM OPERATING PRESSUREPSI Bar kPa MPa450 32 3200 3.2MAXIMUM OPERATING PRESSUREPSI Bar kPa MPa450 32 3200 3.2FOAM TANK REFILL SYSTEMFOAMFILLThe Waterous FoamFill Foam Tank Refill System is completely-automated, making it easier, safer,cleaner and quicker to top off the foam tank or tanks in your apparatus. The FoamFill Foam Tank Refillcan be used with both Class A and B foam and features a dripless coupling available in either brass orstainless steel in 3/4-inch or 1-inch sizes. The unit is powered by a 12- or 24-volt motorized pump.When turned on, a microcontroller identifies if tanks are low, and automatically fills them withoutoverflowing using a stainless steel wick wand and six feet of reinforced hose.• 10 GPM (37.8 l/min)25 26Contents in this brochure are subject to change without notice.

TAKE THE FIGHT TO THE FIRE.Don't wait for fire to come to you. With fuel-powered portable and motor pumps from Waterous, you can take the fight to the fire.Waterous portable and motor pumps range from lightweight, easy-to-carry models to heavy-duty trailer/truck/skid mount models withplenty of fire suppressing power. No matter the location, Waterous has a portable pump for you.PORTABLE AND MOTOR PUMPSPB18-SERIESPORTABLE AND MOTOR PUMPSPORTABLE AND MOTOR PUMPSE300The E300 Motor Pump provides the versatility of a combination apparatus in a skid-mounted design.Equipped with Kubota® 1335cc diesel engine and a Waterous CPT-2 Series Fire Pump.E300MAXIMUM FLOWMAXIMUM PRESSUREGPM l/min l/sec PSI Bar kPa325 1200 20 50 3.5 350100 400 6.5 210 14 1400MPa0.351.4The Waterous PB18 series features four portable pump models. Each PB18 is equipped with a Briggs &Stratton 18hp (13kW) V-Twin gasoline engine and is available with no base or rail base option. Fuel tankis 3-gallon (11 liter) fuel tank that meets the EPA evaporative requirement (40 CFR Part 1060).PB18-4025BMAXIMUM FLOWGPM l/min250 1000l/sec16.5PSI70Bar4.8kPa480MPa0.48Wrap-around base isPORTABLE AND MOTOR PUMPSFLOTO-PUMP MAXIMUM PRESSURE 150 600• 143 lbs. (65.0 kg)10906.56500.65only available onInternational orders.The Waterous Floto-pump was developed to meet the rugged demands of the United StatesForest Service. Now, it is also used for marine service, dewatering, pool maintenance,environmental clean-up and irrigation. Floto-Pumps are available in two models, Standard andPB18-2515GPMl/minl/secPSIBarkPaMPaForestry. Both are powered by a U.S. Motor Power "Power Bee" engine.MAXIMUM FLOWMAXIMUM PRESSURE150 60075 300105901356.59.36509300.650.93Floto Pump StandardGPM l/minl/secPSIBarkPaMPa• 133 lbs. (60.5 kg)MAXIMUM FLOW140 53093022000.2PB18-3030GPMl/minl/secPSIBarkPaMPaMAXIMUM PRESSURE• Bronze Impeller10 40.710577000.7MAXIMUM FLOW400 1500251511000.1• 42 lbs. (19.1 kg)PORTABLE AND MOTOR PUMPSMAXIMUM PRESSURE 100 400 6.5 110 7.6 760 0.76• 135 lbs. (61.2 kg)PB18-G2015GPM l/min l/sec PSI Bar kPa MPaMAXIMUM FLOW 75 300 5 190 13 1300 1.3MAXIMUM PRESSURE 20 80 1.3 320 22 2200 2.2• 152.5 lbs. (64.6 kg)PORTABLE AND MOTOR PUMPSE501-C / E511-CThe E500 Series Motor Pump is specifically designed for mounting on specialized attack vehicles. EquippedFloto Pump High Pressure (Forestry)MAXIMUM FLOWMAXIMUM PRESSUREGPM6010l/min23040l/sec3.8.7PSI35170• Aluminum Impeller with Ni-resist wear rings• 42 lbs. (19.1 kg)Bar312kPa3001200MPa0.31.2PORTABLE AND MOTOR PUMPSwith Kubota 899cc diesel engine and Waterous fire pump. Available in two models: E501 or E511:E501-CGPMl/minl/secPSIBarkPaMPaMAXIMUM FLOW110 4206.610077000.7MAXIMUM PRESSURE50 2003.34002828002.8E511-CGPMl/minl/secPSI Bar kPa MPaMAXIMUM FLOW275 100016.5503.5350.35MAXIMUM PRESSURE100 4006.51901313001.327 28

ARFF FIRE PUMPSFIRE PUMP ACCESSORIESFIREFIGHTING SYSTEMS YOU CAN COUNT ON.Whether fighting fires on the open sea or battling blazes on the runway, you demand pumps that exceed performance standards. To meet thesedemands, our fireboat and aircraft rescue and firefighting (ARFF) pumps are built with the highest quality materials using the latest technology—so you never have to worry about performance or reliability. Tough and rugged, Waterous ARFF pumps deliver the type of knockdown power youneed, when you need it most.ARFF FIRE PUMPSCH-4• Bronze (cast iron optional),horizontally-split volute body• 17-4 stainless steel impeller shaft• Oil- or grease-lubricated ball bearings• Fully-enclosed, bronze, double-hubbedprecision-balanced impeller• Bronze replaceable wear rings• 5-year warrantyDISCHARGE VALVES• Chromium-plated bronze valve ball• Spring-loaded floating seal assembly• Multi-purpose drainport• Manual, push/pull, twist lock (2.5”) mechanismwith panel-mounted “T” handle lock• Optional electric actuator compliesDISCHARGE RELIEF VALVE• Controls discharge pressure by bypassing flow fromdischarge back to suction• Control discharge pressure up to 300 psi (20 bar)• Available in three sizes, up to 2250 GPM (8500 l/min)CH-4 PERFORMANCEwith NFPA requirements for slow actuationGPMl/minl/secPSI Bar kPa MPa1400 5300 88 250 17 1700 1.7ARFF FIRE PUMPSCR / CRU• Gray iron (bronze optional),vertically-split volute body• Fully-enclosed, bronze, double-hubbedprecision-balanced impellerOVERHEATPROTECTION MANAGERMONARCHINTAKE VALVE• 17-4 stainless steel impeller shaft• Oil-splash lubricated ball bearings• Bronze replaceable wear rings• 5-year warranty• Opens when water inside the pump reaches 140º F (60º C)• Flashing warning light on pump panel is• Manual, electric or pneumatic operation• Stainless steel Wafer-Sphere® elementtriggered when water reaches 180º F (82º C)• Polymeric flexible lip sealCR / CRU PERFORMANCE• Water is released to ground• Provision for pre-butterfly relief valveGPMl/minl/secPSI Bar kPa MPaCR2050 7800 130 250 17 1700 1.7ARFF FIRE PUMPSCRU2640 10000 165 250 17 1700 1.7CZ / CZU• High-tensile gray iron (bronze optional),• Fully-enclosed, bronze, double-hubbedvertically-split casingprecision-balanced impeller• 17-4 stainless steel impeller shaft• Bronze replaceable wear rings• Oil-splash lubricated ball bearings• 5-year warrantyCZ / CZU PERFORMANCEPRIMING PUMPS• VPO oil-free primer• Fast, dependable priming• Electrically driven• Operates independently from the pump• Lubrication option (requires priming tank)INTAKE RELIEF VALVE• Pilot-operated for improved performance• Pressure scale markings• Panel-mounted strainerGPMl/minl/secPSI Bar kPa MPaCZ950 3600 60 260 18 1800 1.8CZU1500 5700 95 250 17 1700 1.7ARFF FIRE PUMPSARFF FIRE PUMPSCPT-4UHP Ultra High PressureThis ultra high-pressure performer is a lightweight four-stage centrifugal pump that delivers 90 GPM (350 l/min) at 1350 PSI (93 bar) to produce high-pressure fog, which can knock out fires quickly while the pumper iseither in motion or stationary.• Two-piece, horizonally-split gray iron body • Braided Flexible Graphite Packing• Ni-Resist wear rings to reduce internal leakage • Direct-Engine Mounted with SAE Bellhousing• Bronze ImpellersPRIMING VALVES• Vacuum Activated Priming (VAP) Valve• Stainless steel valve stem• Opens automatically during pump priming• Closes automatically when primer is deactivatedPNEUMATIC SHIFT• Spring-loaded locking control• Dual-action cylinderFIRE PUMP ACCESSORIESCPT-4UHP PERFORMANCEGPMl/minl/secPSI Bar kPa MPa90 350 6.0 1350 93 9300 9.329 30

To help you find the right Waterous products, services and educationaland training seminars, visit our Web site at www.waterousco.com.WORLDWIDEWith customers in Europe, North and South America, the Middle East, Asia, Australia, and Africa,Waterous continues to serve the needs of the global fire industry with unmatched service andcustomer care. Call Waterous today, and discover the force behind the fight.CORPORATE HEADQUARTERS125 HARDMAN AVENUE SOUTH, SOUTH SAINT PAUL, MINNESOTA USA 55075-2456+1- 651- 450-5000 www.waterousco.comF-2733 04/13