Material Safety Data Sheet - Waterproofing Warehouse

Material Safety Data SheetPage 1 of 1Date of Issue: Sept ‘02Ref: MSDS - 366Sikadur-Combiflex ® ®NOT CLASSIFIED AS HAZARDOUS ACCORDING TO CRITERIA OF WORKSAFE AUSTRALIACOMPANY DETAILSCOMPANY: Sika Australia Pty. Limited A.C.N. 001 342 329Sika New Zealand LimitedADDRESS:TELEPHONE:EMERGENCY TELEPHONE NO.:EMERGENCY AFTER HOURS:FAX NUMBER:55 Elizabeth Street, Wetherill Park, NSW 2164 (AUS)85-91 Patiki Road, Avondale, Auckland (NZ)(02) 9725 1145 (AUS)(09) 828 7002 (NZ)(02) 9757 5634 or (02) 9757 5625 (AUS)0800 734 607 (NZ)1 800 033 111 (AUS)0800 734 607(NZ)(02) 9725 3330 (AUS)(09) 828 4091 (NZ)IDENTIFICATIONPRODUCT NAME:Sikadur-Combiflex®OTHER NAMES:HypalonMANUFACTURER'S PRODUCT CODE: None assignedU.N. NUMBER:None assignedDANGEROUS GOODS CLASS:None assignedHAZCHEM CODE:None assignedPOISONS SCHEDULE NUMBER: None assignedUSE:Flexible waterproof sheeting for expansion jointsPHYSICAL DESCRIPTION/PROPERTIES:APPEARANCE:BOILING POINT/MELTING POINT:VAPOUR PRESSURE:SPECIFIC GRAVITY:FLASHPOINT:FLAMMABILITY LIMITS:SOLUBILITY IN WATER:Grey sheetNot availableNot applicableApprox 1.14 kg/litreNot applicableNot applicableNilADVICE NOTE:The information contained in this Material Safety Data Sheet corresponds to our best knowledge at thetime of publication. Each user should read the MSDS and Technical Data Sheet prior to handling anduse.This product is sold subject to our latest standard terms and conditions.

OTHER PROPERTIES:Page 2 of 2Product Name: Sikadur-Combiflex ®Date of Issue: Sept ‘02INGREDIENTS:Chemical Name: CAS Number: Proportion:Chlorosulphonated Polyethylene - > 60 %Carbon Tetrachloride 56-23-5 < 1%Chloroform 67-66-3 < 1 %Non-hazardous ingredients - 100 %HEALTH HAZARD INFORMATIONHEALTH EFFECTS:Acute:Swallowed:Eye:Skin:Inhaled:Chronic:Swallowed:Eye:Skin:Inhaled:FIRST AID:Swallowed:Eye:Skin:Inhaled:First Aid Facilities:ADVICE TO DOCTOR:Ingestion is unlikely to occur however, large amounts may causenausea and vomiting.Not applicable. Exposure to fumes from molten material may causeirritation to eyes.Not applicable. Exposure to molten material may cause skin burns.Not applicable. Exposure to fumes from molten material may causeirritation to mucous membranes and respiratory tract.Not applicable.Not applicable.Not applicable.Not applicable. This product would contain trace amounts ofchlorinated hydrocarbons. Carbon Tetrachloride and chloroform havebeen classified as carcinogens based on tests with laboratory animals.Exposure to carbon tetrachloride at concentrations above the PEL maycause liver damage.If swallowed, rinse mouth with water. Give plenty of water to drink. Ifvomiting occurs, give further water. Contact doctor or PoisonsInformation Centre.If in eyes, hold eyes open, flood with water for at least 15 minutes andsee a doctor.If skin contact occurs, remove contaminated clothing and wash skinthoroughly.Should molten material contact the skin and adhere, cool quickly withrunning water – do not attempt to remove. Seek medical attention.Move to fresh air. Seek medical advice if effects persist.Eye washes and clean running cold water should be available.No adverse health effects are expected with the product in its originalform when used in accordance with this Material Safety Data Sheet. Ifadverse symptoms appear, treat symptomatically.PRECAUTIONS FOR USEEXPOSURE STANDARDS:Exposure standards for constituents, thermal degradation products:

TWA TLVCarbon Tetrachloride 10 ppm 5 ppm A2 ACGIHChloroform 50 ppm 10 ppm A2 ACGIHHydrogen ChlorideENGINEERING CONTROLS:PERSONAL PROTECTION:FLAMMABILITY:STORAGE & TRANSPORT:N/APage 3 of 3Product Name: Sikadur-Combiflex ®Date of Issue: Sept ‘02Carcinogen CategoryThese exposure standards are guides to be used in the control ofoccupational health hazards. All atmospheric contamination should bekept to as low a level as is workable. Exposure standards should not beused as fine dividing lines between safe and dangerous concentrationsof chemicals. They are not a measure of relative toxicity.If welding, use in well-ventilated area. Avoid exposure to fumesemanating from molten material. The use of forced ventilation awayfrom personnel can be effective.Use heat protection gloves when handling hot or molten material. Theuse of safety goggles / glasses is recommended.Do not store or consume food, drink or tobacco in an area where theymay become contaminated with this material. Wash thoroughly beforeeating, smoking, applying cosmetics etc. Thoroughly launder workclothes before reuse.Solid polymer can be combusted only with difficulty. May emit fumesduring combustion and welding containing:Carbon MonoxideCarbon DioxideFormaldehydeHydrogen ChlorideSAFE HANDLING INFORMATIONStore in cool, dry conditions. Protect from exposure to UV light. Stableat normal temperatures and storage conditions.Not classified as Dangerous GoodsSPILLS & DISPOSAL: Spills Not applicable.Disposal. Unlikely to be hazardous to aquatic life. Do not dispose of insewer or storm water system. Seek advice from local Authority onrequirements for approved methods of disposal.FIRE/EXPLOSION HAZARD:OTHER INFORMATION:CONTACT POINT:Stable under normal conditions.On combustion or during welding processes, toxic fumes includingthose of hydrogen chloride, carbon monoxide and carbon dioxide maybe emitted. Fire fighters should wear self-contained breathingapparatus if risk of exposure to fumes of combustion products.Suitable extinguishing media – water, foam, carbon dioxide, drychemical.Avoid storing near strong oxidizing agents, acids or in contact withorganic solvents.Responsible Care Co-ordinator or Laboratory Manager(02) 9725 1145 (AUS)Operations Manager (09) 828 7002 or (09) 820 1432 (NZ)