Instruction Manual Manual de Instrucciones Manuel d'Instructions

Please do not return unit to retailer.Por favor, no devuelva el aparato al lugar de compra.Veuillez ne pas retourner l’outil au détaillant.1 -800 -554 -6723www.poulan -pro.comIMPORTANT MANUAL - Do not throw awayMANUAL IMPORTANTE - No lo descarteMANUEL IMPORTANT - À ConserverRBVM200VSWARNING:Read and follow all Safety Rules and Operating Instructions beforeusing this product. Failure to do so can result in serious injury.ADVERTENCIA:Lea el manual de instrucciones y siga todas las advertencias einstrucciones de seguridad. El no hacerlo puede resultar en lesionesgraves.AVERTISSEMENT:Veuillez lire le manuel d’instructions et bien respecter tous lesavertissements et toutes les instructions de sécurité. Tout défautde le faire pourrait entraîner des blessures graves.Poulan PRO1030 Stevens Creek RoadAugusta, GA 30907Instruction ManualManual de InstruccionesManuel d’InstructionsPoulan PRO5855 Terry Fox WayMississauga, Ontario L5V 3E4545146927 Rev. 5 9/1/07 BRWENGLISH ESPAÑOL FRANÇAIS

IDENTIFICATION OF SAFETY SYMBOLSWARNING: This unit can be dangerous! Careless or improperuse can cause serious injury.Read your operator’s manual carefully until you completely understandand can follow all warnings and safety rules before operating the unit.Failure to do so can result in serious injury. Save operator’s manual.The blower can throw objects violently.You can be blinded or injured.Always wear hearing protection andsafety glasses marked Z87. Alwayswear heavy, long pants, longsleeves, boots and gloves.Hazard zone for thrown objects. Keep children, bystanders,and animals away from work area a minimumof 30 feet (10 meters) when starting or operatingunit. Do not point blower nozzle in the direction ofpeople or pets.Secure hair above shoulder length. Donot wear jewelry, loose clothing, orclothing with loosing hanging straps,ties, tassels, etc. They can be caught inmoving parts.Always stop unit and disconnect spark plug beforecleaning or servicing.WARNING: Stop the engine before opening the vacuum inlet door. The engine mustbe stopped and the impeller blades no longer turning to avoid serious injury from the rotatingblades. Gently tilt the handle of the screwdriver toward the front of the unit to release the latchwhile pulling up on the vacuum inlet cover with your other hand.-- 2 --

IDENTIFICATION OF SAFETY SYMBOLSWhen using the vacuum attachment, the unit is designed to pick up drymaterial such as leaves, grass, small twigs, and bits of paper. Do notvacuum stones, gravel, metal, broken glass, etc., to avoid severe damageto the impeller.WARNING: Fire hazard. Never mix, pour, or store gasoline oruse the unit near a flame or sparks (including smoking, open flames, orwork that can cause sparks).WARNING: Failure to follow allSafety Rules and Precautions can result inserious injury.KNOW YOUR UNITS Read your instruction manual carefully untilyou completely understand and can followall warnings and safety rules before operatingthe unit.D Restrict unit to users who understand andwill follow all warnings and safety rules inthis manual.SAFETY RULESWARNING: Inspect area before startingunit. Remove all debris and hard objectssuch as rocks, glass, wire, etc. that can ricochet,be thrown, or otherwise cause injury ordamage during operation.Use your unit as a blower for:D Sweeping debris or grass clippings fromdriveways, sidewalks, patios, etc.D Blowing grass clippings, straw, or leaves intopiles, around joints, or between bricks.Use your unit as a vacuum for:D Picking up dry material such as leaves,grass, small twigs, and bits of paper.D For best results during vacuum use, operateyour unit at high speed.D Move slowly back and forth over the materialas you vacuum. Avoid forcing the unitinto a pile of debris as this can clog the unit.D Keep the vacuum tube about an inch abovethe ground for best results.PLAN AHEADD Always wear eye protection when operating,servicing, or performing maintenanceon unit. Wearing eye protection will help toprevent rocks or debris from being blown orricocheting into eyes and face which canresult in blindness and/or serious injury.Eye protection should be marked Z87.D Always wear foot protection. Do not gobarefoot or wear sandals.D Always wear respirator or face mask whenworking with unit in dusty environments.-- 3 --D Secure hair so it is above shoulder length.Keep loose hair, loose clothing, fingers, andall other parts of the body away from openingsand moving parts. Hair, jewelry, loose clothing,or clothing with loosely hanging straps,ties, tassels, etc., can be caught in movingparts.D Do not operate unit when you are tired, ill, upset,or if you are under the influence of alcohol,drugs, or medication.D Keep children, bystanders, and animalsaway from work area a minimum of 30 feet(10 meters) when starting or operating unit.Do not point the blower nozzle in the directionof people or pets.HANDLE FUEL WITH CAUTION, IT ISHIGHLY FLAMMABLED Eliminate all sources of sparks or flame (includingsmoking, open flames, or work thatcan cause sparks) in the areas where fuel ismixed, poured, or stored.D Mix and pour fuel in an outdoor area; storefuel in a cool, dry, well ventilated place; usean approved, marked container for all fuelpurposes.D Do not smoke while handling fuel or whileoperating the unit.D Make sure the unit is properly assembledand in good operating condition.D Do not fill fuel tank while engine is hot orrunning.D Avoid spilling fuel or oil. Wipe up fuel spillsbefore starting engine.D Move at least 10 feet (3 meters) away fromfuel and fueling site before starting engine.D Always store gasoline in a container approvedfor flammable liquids.OPERATE YOUR UNIT SAFELYWARNING: Stop the engine beforeopening the vacuum inlet door. The enginemust be stopped and the impeller blades nolonger turning to avoid serious injury from therotating blades.

D Inspect unit before each use for worn,loose, missing, or damaged parts. Do notuse until unit is in proper working order.D Keep outside surfaces free of oil and fuel.D Never start or run engine inside a closedroom, building or other unventilated area.Breathing exhaust fumes can kill.D To avoid static electricity discharge, do notwear rubber gloves or any other insulatedgloves while operating unit.D Do not set unit on any surface except aclean, hard area while engine is running.Debris such as gravel, sand, dust, grass,etc. could be picked up by the air intake andthrown out through discharge opening,damaging unit, property, or causing seriousinjury to bystanders or operator.D Avoid dangerous environments. Do not usein unventilated areas or where explosivevapors or carbon monoxide build up couldbe present.D Do not overreach or use from unstable surfacessuch as ladders, trees, steep slopes,rooftops, etc. Keep firm footing and balanceat all times.D Never place objects inside the blowertubes; always direct the blowing debrisaway from people, animals, glass, and solidobjects such as trees, automobiles, walls,etc. The force of air can cause rocks, dirt, orsticks to be thrown or to ricochet which canhurt people or animals, break glass, orcause other damage.D Never run unit without the proper equipmentattached. When using your unit as ablower, always install blower tubes. Whenusing your unit as a vacuum, always installvacuum tubes and vacuum bag assembly.Make sure vacuum bag assembly is completelyzipped.D Check air intake opening, blower tubes,vacuum tubes, and elbow tube frequently,always with engine stopped and spark plugdisconnected. Keep vents and dischargetubes free of debris which can accumulateand restrict proper air flow.D Never place any object in the air intake openingas this could restrict proper air flow andcause damage to the unit.D Never use for spreading chemicals, fertilizers,or other substances which may containtoxic materials.D To avoid spreading fire, do not use near leafor brush fires, fireplaces, barbecue pits,ashtrays, etc.D Use only for jobs explained in this manual.MAINTAIN YOUR UNIT PROPERLYWARNING: Disconnect spark plug beforeperforming maintenance except for carburetoradjustments.D Have all maintenance other than the recommendedprocedures described in the instructionmanual performed by an authorizedservice dealer.D Use only recommended Poulan PRO replacementparts; use of any other partsmay void your warranty and cause damageto your unit.D Empty fuel tank before storing the unit. Useup fuel left in carburetor by starting engine andletting it run until it stops.D Do not use any accessory or attachmentother than those recommended by manufacturerfor use with your unit.D Do not store the unit or fuel in a closed areawhere fuel vapors can reach sparks or anopen flame from hot water heaters, electricmotors or switches, furnaces, etc.D Store in a dry area out of reach of children.SPECIAL NOTICE: Exposure to vibrationsthrough prolonged use of gasoline poweredhand tools could cause blood vessel ornerve damage in the fingers, hands, andjoints of people prone to circulation disordersor abnormal swelling. Prolonged use in coldweather has been linked to blood vessel damagein otherwise healthy people. If symptomsoccur such as numbness, pain, loss ofstrength, change in skin color or texture, orloss of feeling in the fingers, hands, or joints,discontinue the use of this tool and seekmedical attention. An antivibration systemdoes not guarantee the avoidance of theseproblems. Users who operate power tools ona continual and regular basis must monitorclosely their physical condition and the conditionof this tool.SPECIAL NOTICE: This unit is equippedwith a temperature limiting muffler and sparkarresting screen which meets the requirementsof California Codes 4442 and 4443. AllU.S. forest land and the states of California,Idaho, Maine, Minnesota, New Jersey, Oregon,and Washington require by law thatmany internal combustion engines beequipped with a spark arresting screen. If youoperate in a locale where such regulations exist,you are legally responsible for maintainingthe operating condition of these parts. Failureto do so is a violation of the law. Refer to theMAINTENANCE section for information onmaintenance of the muffler and spark arrestingscreen.-- 4 --

WARNING: Stop engine and be surethe impeller blades have stopped turning beforeopening the vacuum inlet door or attemptingto insert or remove the vacuum orblower tubes. The rotating blades can causeserious injury. Always disconnect the sparkplug before performing maintenance or accessingmovable parts.ASSEMBLYHIGH -SPEED NOZZLE ASSEMBLYWhen greater air speed is desired, use thehigh -speed nozzle.1. Align the slots on the nozzle with the tabson the lower blower tube.High -SpeedNozzleWARNING: If you receive your unitassembled, check each step to insure yourunit is properly assembled and all fastenersare secure. Follow all safety information inthe manual and on the unit.D A standard screwdriver is required for assembly.BLOWER TUBE ASSEMBLY1. Align the slots on the lower blower tubewith the tabs on the upper blower tube.Upper Blower TubeLower Blower TubeLower BlowerTabTubeSlot2. Slide the nozzle onto the lower blower tube.3. Turn the nozzle clockwise until a click isfelt to secure the nozzle to the lower blowertube.VACUUM BAG ASSEMBLY1. Open the zipper on the vacuum bag andinsert the elbow tube.2. Push the small end of the elbow tubethrough the small opening in the bag.ElbowTubeRibTabSlot2. Slide the lower blower tube onto the upperblower tube.3. Turn the lower blower tube clockwise untila click is felt to secure the lower blowertube to the upper blower tube.NOTE: When the upper and lower blowertubes are assembled together properly, thearrows on both tubes will be aligned.ZipperOpeningSmall OpeningNOTE: Make sure edge of the small openingis flush against the flared area of the elbowtube, and the rib on the elbow tube is on thebottom.3. Close the zipper on the bag. Make sure thezipper is closed completely.4. Remove blower tubes from engine.4. Align the rib on the upper blower tube withthe groove in the blower outlet; slide thetube into place.NOTE: Knob must be loose enough to allowblower tubes to be inserted in blower outlet.Loosen knob by turning counterclockwise.Blower OutletGrooveRib5. Secure the tubes by turning the knobclockwise.6. To remove the tubes, turn the knob counterclockwiseto loosen the tubes; removethe tubes.-- 5 --RibGroove5. Insert the elbow tube into the blower outlet.Make sure elbow tube rib is aligned withthe blower outlet groove.6. Turn knob clockwise to secure elbow tube.VACUUM TUBE ASSEMBLYWARNING: Stop engine and be surethe impeller blades have stopped turning beforeopening the vacuum inlet door or attemptingto insert or remove the vacuum orblower tubes. The rotating blades can causeserious injury.

1. Insert the tip of a screwdriver into the latcharea of the vacuum inlet.Latch Area BlowerOutlet6. Align slanted end of lower vacuum tube asshown. Firmly push lower vacuum tubeinto upper vacuum tube.LatchAreaVacuum Inlet Cover2. Gently tilt the handle of the screwdriver towardthe front of the unit to release thelatch while pulling up on the vacuum inletcover with your other hand.3. Hold the vacuum inlet cover open until uppervacuum tube is installed.VacuumInletCoverVacuum Inlet4. Align the tabs on the inside of the vacuum inletwith the slots on the upper vacuum tube.cSlanted end oflower vacuum tubeHOW TO CONVERT UNIT FROMVACUUM USE TO BLOWER USE1. Remove the elbow tube and vacuum bagby turning the knob counterclockwise toloosen the elbow tube.2. Remove the vacuum tubes by turning thetubes clockwise.3. Close the vacuum inlet cover and makesure it is latched closed.4. Reinstall the blower tubes (see BLOWERTUBE ASSEMBLY).SHOULDER STRAP ADJUSTMENT1. Hold the unit as shown with the muffler sidefacing away from your body and clothes.2. Pass the shoulder strap over your headand onto your right shoulder.3. Extend your left arm toward the rear of thevacuum bag.4. Adjust shoulder strap until the vacuumbag/shoulder strap seam lies betweenyour thumb and index finger.5. Make sure air flows freely from the elbowtube into bag. If bag is kinked, the unit willnot operate properly.TabSlot5. Push the upper vacuum tube into the vacuuminlet. Turn the tube counterclockwiseuntil a click is felt to secure the tube to theblower unit.-- 6 --

OPERATIONKNOW YOUR BLOWERREAD THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.Compare the illustrations with your unit to familiarize yourself with the location of the various controlsand adjustments. Save this manual for future reference.Upper Vacuum TubeElbow TubeLower Vacuum TubeStarterRopeFuel MixFill CapThrottleTriggerSTOPSwitchSparkPlugUpper Blower TubeChoke LeverPrimerButtonSTOP SWITCHThe STOP switch is used to stop the engine.To stop the engine, push and hold the STOPswitch in the STOP position until the enginestops.Vacuum HandleTHROTTLE TRIGGERThe THROTTLE TRIGGER is used to selectthe desired engine speed.OPERATING POSITIONBlowerVacuumVacuum BagLower Blower TubeHigh -SpeedNozzlePRIMER BUTTONThe PRIMER BUTTON removes air from thecarburetor and fuel lines and fills them with fuel.This allows you to start the engine with fewerpulls on the starter rope. Activate primer buttonby pressing it and allowing it to return to its originalposition.CHOKE LEVERThe CHOKE helps to supply fuel to the enginetoaidincoldstarting.Activatethechokebymoving the choke lever to the FULL CHOKEposition. After engine attempts to start, move thechoke lever to the HALF CHOKE position.Once engine starts, move choke lever to theRUN position.OPERATING TIPSS While vacuuming or blowing debris, holdthe unit with the muffler side facing awayfrom your body and clothes (see OPERAT-ING POSITION illustration above).S To reduce the risk of hearing lossassociated with sound level(s), hearingprotection is required.S To reduce the risk of injury associated withcontacting rotating parts, stop the engine beforeinstalling or removing attachments. Donot operate without guard(s) in place.S Operate power equipment only at reasonablehours -not early in the morning or late at nightwhen people might be disturbed. Comply withtimes listed in local ordinances. Usual recommendationsare 9:00 a.m. to 5:00 p.m.,Monday though Saturday.S To reduce noise levels, limit the number ofpieces of equipment used at any one time.-- 7 --

S To reduce noise levels, operate powerblowers at the lowest possible throttlespeed to do the job.S Use rakes and brooms to loosen debris beforeblowing.S In dusty conditions, slightly dampen surfacesor use a mister attachment when wateris available.S Conserve water by using power blowersinstead of hoses for many lawn and gardenapplications, including areas such as gutters,screens, patios, grills, porches, and gardens.S Watch out for children, pets, open windows,or freshly washed cars. Blow debris awaysafely.S Use the full blower nozzle extension so theair stream can work close to the ground.S After using blowers and other equipment,CLEAN UP! Dispose of debris in trash receptacles.BEFORE STARTING ENGINEHOW TO STOP YOUR ENGINED Release the throttle trigger.S Push and hold the STOP switch in theSTOP position until the engine stops.HOW TO START YOUR ENGINEWARNING: You MUST make surethe tubes are secure before using the unit.D Fuel engine. Move at least 10 feet (3 meters)away from the fueling site.D Hold the unit in the starting position asshown. Make sure the blower end is directedaway from people, animals, glass,and solid objects.STARTING POSITIONBlowerWARNING: Be sure to read the fuelinformation in the safety rules before you begin.If you do not understand the safety rules,do not attempt to fuel your unit. Call1-800-554-6723.FUELING ENGINEWARNING: Remove fuel cap slowlywhen refueling.HELPFUL TIPTo obtain the correct oil mixratio, pour 3.2 ounces of2-cycle synthetic oil intoone gallon of fresh gas.This engine is certified to operate on unleadedgasoline. Before operation, gasoline must bemixed with a good quality synthetic 2-cycleair-cooled engine oil designed to be mixed at aratio of 40:1. Poulan PRO brand synthetic oil isrecommended. Mix gasoline and oil at a ratio of40:1. A 40:1 ratio is obtained by mixing 3.2ounces (95 ml) of oil with 1 gallon (4 liters) ofunleaded gasoline. DO NOT USE automotiveoil or marine oil. These oils will cause enginedamage. When mixing fuel, follow instructionsprinted on container. Once oil is added togasoline, shake container momentarily toassure that the fuel is thoroughly mixed. Alwaysread and follow the safety rules relating to fuelbefore fueling your unit.IMPORTANTExperience indicates that alcohol blendedfuels (called gasohol or using ethanol ormethanol) can attract moisture which leads toseparation and formation of acids duringstorage. Acidic gas can damage the fuelsystem of an engine while in storage. To avoidengine problems, empty the fuel systembefore storage for 30 days or longer. Drain thegas tank, start the engine and let it run until thefuel lines and carburetor are empty. Use freshfuel next season. Never use engine orcarburetor cleaner products in the fuel tank orpermanent damage may occur.-- 8 --VacuumWARNING:When starting engine,hold the unit as illustrated. Do not set unit on anysurface except a clean, hard area when startingengine or while engine is running. Debris suchas gravel, sand, dust, grass, etc. could bepicked up by the air intake and thrown outthrough the discharge opening, damaging theunit or property, or causing serious injury to bystandersor the operator.HELPFUL TIPIf your engine still does notstart after following theseinstructions, please call1 -800 -554 -6723.STARTING A COLD ENGINE (or warmengine after running out of fuel)1. Slowly press the primer bulb 6 times.2. Move choke lever to the FULL CHOKE position.3. Squeeze the throttle trigger fully and holdthrough all remaining steps.StarterHandleChokeLeverPrimerBulb

4. Pull starter rope handle sharply until enginesounds as if it is trying to start, but do not pullrope more than 6 times.5. As soon as engine sounds as if it is trying tostart, move choke lever to HALF CHOKEposition.6. Pull starter rope sharply until engine runs,but no more than 6 pulls. NOTE: If the enginedoesn’t start after 6 pulls (at the HALFCHOKE position), move the choke lever tothe FULL CHOKE position and press theprimer bulb 6 times. Squeeze and hold thethrottle trigger and pull the starter rope 2more times. Move the choke lever to theHALF CHOKE position and pull the starterrope until the engine runs, but no morethan 6 pulls. If the engine still doesn’t start,it is probably flooded. Proceed to START-ING A FLOODED ENGINE.7. Oncetheenginestarts,allowittorun10seconds,then move the choke lever to theRUN position. Allow the unit to run for 30more seconds at RUN before releasing thethrottle trigger. NOTE: If engine dies withthe choke lever in the RUN position, moveWARNING: Avoid touching mufflerunless engine and muffler are cold. A hotmuffler can cause serious burns.WARNING: Stop engine and be surethe impeller blades have stopped turning beforeopening the vacuum inlet door or attemptingto insert or remove the vacuum orblower tubes. The rotating blades can causeserious injury. Always disconnect the sparkplug before performing maintenance or accessingmovable parts.HELPFUL TIPIMPORTANT: Have allrepairs other than the recommendedmaintenancedescribed in the instructionmanual performed by anauthorized service dealer.If any dealer other than an authorizedservice dealer performs work on theproduct, Poulan PRO may not pay forrepairs under warranty. It is your responsibilityto maintain and performgeneral maintenance.GENERAL RECOMMENDATIONSThe warranty on this unit does not cover itemsthat have been subjected to operator abuseor negligence. To receive full value from thewarranty, the operator must maintain unit asinstructed in this manual. Various adjustmentswill need to be made periodically toproperly maintain your unit.MAINTENANCE-- 9 --the choke lever to the HALF CHOKE positionand pull the rope until engine runs, butno more than 6 pulls.STARTING A WARM ENGINE1. Move the choke lever to the HALF CHOKEposition.2. Squeeze the throttle trigger fully and holdthrough all remaining steps.3. Pull starter rope sharply until engine runs,but no more than 6 pulls.4. Allow engine to run 15 seconds, then movethe choke lever to RUN.NOTE: If engine has not started, pull starterrope 5 more pulls. If engine still does not run, itis probably flooded.STARTING A FLOODED ENGINEFlooded engines can be started by placing thechoke lever in the RUN position; then, pull therope to clear the engine of excess fuel. Thiscould require pulling the starter handle manytimes depending on how badly the unit isflooded. If the unit still doesn’t start, refer toTROUBLESHOOTING TABLE or call1-800-554-6723.CHECK FOR LOOSEFASTENERS AND PARTSS MufflerS Spark Plug BootS Air FilterS Housing ScrewsCHECK FOR DAMAGED OR WORNPARTSContact an authorized service dealer for replacementof damaged or worn parts.S Fuel Tank - Do not use unit if fuel tank showssigns of damage or leaks.S Vacuum Bag - Do not use vacuum bag if itis torn or damaged.INSPECT AND CLEAN UNIT ANDDECALSS After each use, inspect complete unit forloose or damaged parts. Clean the unit anddecals using a damp cloth with a mild detergent.S Wipe off unit with a clean dry cloth.CLEAN AIR FILTERA dirty air filter decreases engine performanceand increases fuel consumption andharmful emissions. Always clean or replaceair filter after every 5 hours of operation oryearly, whichever comes first.ButtonAir FilterCoverAir Filter

Cleaning the air filter:1. Clean the cover and the area around it tokeep debris from falling into the carburetorchamber when the cover is removed.NOTE: Move choke lever to RUN positionbefore opening air filter cover.2. Open air filter cover by pushing button(see illustration). Remove air filter.NOTE: Do not clean filter in gasoline or otherflammable solvent. Doing so can create a firehazard or produce harmful evaporative emissions.3. Wash the filter in soap and water.4. Allow filter to dry.5. Apply a few drops of oil to the filter;squeeze filter to distribute oil.6. Replace parts.REPLACE SPARK PLUGReplace spark plug each year to ensure theengine starts easier and runs better. Setspark plug gap at 0.025 inch (0.6 mm). Ignitiontiming is fixed, nonadjustable.1. Twist, then pull off spark plug boot.2. Remove spark plug from cylinder and discard.3. Replace with Champion RCJ-6Y sparkplug and tighten securely with a 3/4 inch(19 mm) socket wrench.4. Reinstall the spark plug boot.REPLACE FUEL FILTERTo replace fuel filter, drain unit by running it dryof fuel, then remove fuel cap/retainer assemblyfrom tank. Pull filter from tank and removeit from the fuel line. Install new fuel filter on fuelline; reinstall parts.CHECK MUFFLER MOUNTINGSCREWSOnce each year, ensure muffler mountingscrews are tightened securely to preventdamage.MufflerMountingScrewINSPECT MUFFLER AND SPARKARRESTING SCREENWARNING: The muffler on this productcontains chemicals known to the State ofCalifornia to cause cancer.As the unit is used, carbon deposits build upon the muffler and spark arresting screen,and must be removed to avoid creating a firehazard or affecting engine performance.Muffler CoverSparkArrestingScreenHoodFuel FilterFuel LineScrewsReplace the spark arresting screen every 50hours of operation or if any damage or breaksin the screen are noted.NOTE: Do not attempt to clean the spark arrestingscreen.1. Remove 3 screws from muffler cover.Remove muffler cover.2. Loosen and remove 4 screws from themuffler hood.3. Remove the muffler hood and spark arrestingscreen.4. Install new spark arresting screen.5. Reinstall muffler hood and 4 screws. Tightenscrews securely.6. Reinstall muffler cover and 3 screws.Tighten securely.NOTE: If any part of the muffler is cracked,broken or damaged, we recommend that themuffler be replaced.-- 10 --

CARBURETOR ADJUSTMENTThe carburetor has been carefully set at thefactory. Adjustments may be necessary if younotice any of the following conditions:S Engine will not idle when the throttle is released.Idle Speed AdjustmentAllow engine to idle. Adjust speed until engineruns without stalling (idle speed too slow).S Turn idle speed screw clockwise to increaseengine speed if engine stalls or dies.S Turn idle speed screw counterclockwise todecrease engine speed.Idle Speed ScrewAirFilterCoverIf you require further assistance or are unsureabout performing this procedure, contact anauthorized service dealer or call1 -800 -554 -6723.STORAGEWARNING: Perform the followingsteps after each use:S Allow engine to cool, and secure the unitbefore storing or transporting.S Store unit and fuel in a well ventilated areawhere fuel vapors cannot reach sparks oropen flames from water heaters, electricmotors or switches, furnaces, etc.S Store unit with all guards in place. Positionunit so that any sharp object cannot accidentallycause injury.S Store unit and fuel well out of the reach ofchildren.SEASONAL STORAGEPrepare unit for storage at end of season or ifit will not be used for 30 days or more.If your unit is to be stored for a period of time:S Clean the entire unit before lengthy storage.S Store in a clean dry area.S Lightly oil external metal surfaces.FUEL SYSTEMUnder FUELING ENGINE in the OPERA-TION section of this manual, see message labeledIMPORTANT regarding the use of gasoholin your engine.Fuel stabilizer is an acceptable alternative inminimizing the formation of fuel gum depositsduring storage. Add stabilizer to gasoline in fueltank or fuel storage container. Follow the mixinstructions found on stabilizer container. Runengine at least 5 minutes after adding stabilizer.HELPFUL TIPDuring storage of your gas/oil mixture, the oil will separatefrom the gas.We recommend that youshake the gas can weeklyto insure proper blending ofthe gas and oil.ENGINES Remove spark plug and pour 1 teaspoon of40:1, 2-cycle engine oil (air cooled) throughthe spark plug opening. Slowly pull thestarter rope 8 to 10 times to distribute oil.S Replace spark plug with new one of recommendedtype and heat range.S Clean air filter.S Check entire unit for loose screws, nuts,and bolts. Replace any damaged, broken,or worn parts.S At the beginning of the next season, useonly fresh fuel having the proper gasoline tooil ratio.OTHERS Do not store gasoline from one season toanother.S Replace your gasoline can if it starts to rust.-- 11 --

TROUBLESHOOTING TABLEWARNING: Always stop unit and disconnect spark plug before performing any of therecommended remedies below other than remedies that require operation of the unit.TROUBLE CAUSE REMEDYEngine will notstart.1. Engine flooded.Engine will notidle properly.Engine will notaccelerate,lacks power, ordies under aload.Engine smokesexcessively.Engine runs hot.2. Fuel tank empty.3. Spark plug not firing.4. Fuel not reachingcarburetor.5. Compression low.1. Fuel not reachingcarburetor.2. Carburetor requiresadjustment.3. Crankshaft seals worn.4. Compression low.1. Air filter dirty.2. Fuel not reachingcarburetor.3. Spark plug fouled.4. Carburetor requiresadjustment.5. Carbon build up.6. Compression low.1. Choke partially on.2. Fuel mixture incorrect.3. Air filter dirty.4. Carburetor requiresadjustment.1. Fuel mixture incorrect.2. Spark plug incorrect.3. Carburetor requiresadjustment.4. Carbon build up.1. See “Starting a Flooded Engine”in Operation section.2. Fill tank with correct fuel mixture.3. Install new spark plug.4. Check for dirty fuel filter; replace.Check for kinked or split fuel line;repair or replace.5. Contact an authorized service dealer.1. Check for dirty fuel filter; replace.Check for kinked or split fuel line;repair or replace.2. Contact an authorized service dealer.3. Contact an authorized service dealer4. Contact an authorized service dealer.1. Clean or replace air filter.2. Check for dirty fuel filter; replace.Check for kinked or split fuel line;repair or replace.3. Clean or replace spark plugand re-gap.4. Contact an authorized service dealer.5. Contact an authorized service dealer.6. Contact an authorized service dealer.1. Adjust choke.2. Empty fuel tank and refill withcorrect fuel mixture.3. Clean or replace air filter.4. Contact an authorized service dealer.1. See “Fueling Engine” in Operationsection.2. Replace with correct spark plug.3. Contact an authorized service dealer.4. Contact an authorized service dealer.-- 12 --

Poulan PRO, a division of Husqvarna OutdoorProducts Inc., warrants to the original consumerpurchaser that each new Poulan PRO brandgasoline tool or attachment is free from defectsin material and workmanship and agrees to repairor replace under this warranty any defectivegasoline product or attachment as follows fromthe original date of purchase.2YEARS -Parts and Labor, when used forhousehold purposes.90 DAYS - Parts and Labor, when used forcommercial, professional, or income producingpurposes.30 DAYS - Parts and Labor, if used for rentalpurposes.This warranty is not transferable and does notcover damage or liability caused by improperhandling, improper maintenance or alteration, orthe use of accessories and/or attachments notspecifically recommended by Poulan PRO forthis tool. This warranty does not cover tune -up,spark plugs, filters, starter ropes, starter springs,cutting line, or rotating head parts that will wearand require replacement with reasonable useduring the warranty period. This warranty doesnot cover pre -delivery setup or normal adjustmentsexplained in the instruction manual. Thiswarranty does not cover transportation costs.In the event you have a claim under this warranty,you must return the product to an authorizedservice dealer.Should you have any unanswered questionsconcerning this warranty, please contact:Poulan PRO, a division ofHusqvarna Outdoor Products Inc.1030 Stevens Creek RoadAugusta, GA 309071 -800 -554 -6723LIMITED WARRANTY-- 13 --In Canada, contact:Poulan PRO5855 Terry Fox WayMississauga,Ontario L5V3E4Giving the model number, serial number anddate of purchase of your product and the nameand address of the authorized dealer fromwhom it was purchased.THIS WARRANTY GIVES YOU SPECIFICLEGAL RIGHTS, AND YOU MAY HAVE OTH-ER RIGHTS WHICH VARY FROM STATE TOSTATE.NO CLAIMS FOR CONSEQUENTIAL OROTHER DAMAGES WILL BE ALLOWED,AND THERE ARE NO OTHER EXPRESSWARRANTIES EXCEPT THOSE EX-PRESSLY STIPULATED HEREIN.SOME STATES DO NOT ALLOW LIMITA-TIONS ON HOW LONG AN IMPLIED WAR-RANTY LASTS OR THE EXCLUSION ORLIMITATIONS OF INCIDENTAL OR CONSE-QUENTIAL DAMAGES, SO THE ABOVE LIM-ITATIONS OR EXCLUSION MAY NOT APPLYTO YOU.This is a limited warranty within the meaning ofthat term as defined in the Magnuson -Moss Actof 1975.The policy of Poulan PRO is to continuouslyimprove its products. Therefore, PoulanPRO reserves the right to change, modify, ordiscontinue models, designs, specifications,and accessories of all products at any timewithout notice or obligation to any purchaser.U.S. EPA/CALIFORNIA/ENVIRONMENT CANADAEMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGA-TIONS: The U.S. Environmental ProtectionAgency, California Air Resources Board, EnvironmentCanada and Poulan PRO arepleased to explain the emissions control systemwarranty on your year 2007 and latersmall off -road engine. In California, all smalloff -road engines must be designed, built, andequipped to meet the State’s stringent anti -smog standards. Poulan PRO must warrantthe emission control system on your smalloff -road engine for the periods of time listedbelow provided there has been no abuse, neglect,or improper maintenance of your smalloff -road engine. Your emission control systemincludes parts such as the carburetor, theignition system and the fuel tank (Californiaonly). Where a warrantable condition exists,Poulan PRO will repair your small off -roadengine engine at no cost to you. Expensescovered under warranty include diagnosis,parts and labor.MANUFACTURER’S WARRANTY COVER-AGE: If any emissions related part on your engine(as listed under Emissions Control WarrantyParts List) is defective or a defect in the materialsor workmanship of the engine causes thefailure of such an emission related part, the partwill be repaired or replaced by Poulan PRO.OWNER’S WARRANTY RESPONSIBILI-TIES: As the small off -road engine engine owner,you are responsible for the performance ofthe required maintenance listed in your instructionmanual. Poulan PRO recommends that youretain all receipts covering maintenance on yoursmall off -road engine, but Poulan PRO cannotdeny warranty solely for the lack of receipts orfor your failure to ensure the performance of allscheduled maintenance. As the small off -roadengine engine owner, you should be aware thatPoulan PRO may deny you warranty coverageif your small off -road engine engine or a part of ithas failed due to abuse, neglect, improper maintenance,unapproved modifications, or the useof parts not made or approved by the original

equipment manufacturer. You are responsiblefor presenting your small off -road engine to anPoulan PRO authorized repair center as soonas a problem exists. Warranty repairs should becompleted in a reasonable amount of time, notto exceed 30 days. If you have any questionsregarding your warranty rights and responsibilities,you should contact your nearest authorizedservice center or call Poulan PRO at1 -800 -554 -6723. WARRANTY COM-MENCEMENT DATE: The warranty period beginson the date the small off -road engine ispurchased. LENGTH OF COVERAGE: Thiswarranty shall be for a period of two years fromthe initial date of purchase. WHAT IS COV-ERED: REPAIR OR REPLACEMENT OFPARTS. Repair or replacement of any warrantedpart will be performed at no charge to theowner at an approved Poulan PRO servicingcenter. If you have any questions regarding yourwarranty rights and responsibilities, you shouldcontact your nearest authorized service centeror call Poulan PRO at 1 -800 -554 -6723. WAR-RANTY PERIOD: Any warranted part which isnot scheduled for replacement as requiredmaintenance, or which is scheduled only forregular inspection to the effect of “repair or replaceas necessary” shall be warranted for 2years. Any warranted part which is scheduledfor replacement as required maintenance shallbe warranted for the period of time up to the firstscheduled replacement point for that part.DIAGNOSIS: The owner shall not becharged for diagnostic labor which leads tothe determination that a warranted part is defectiveif the diagnostic work is performed atan approved Poulan PRO servicing center.CONSEQUENTIAL DAMAGES: Poulan PROmay be liable for damages to other engine componentscaused by the failure of a warrantedpart still under warranty. WHAT IS NOT COV-ERED: All failures caused by abuse, neglect, orimproper maintenance are not covered. ADD -ON OR MODIFIED PARTS: The use of add -onor modified parts can be grounds for disallowinga warranty claim. Poulan PRO is not liable tocover failures of warranted parts caused by theuse of add -on or modified parts.HOW TO FILE A CLAIM: If you have any questionsregarding your warranty rights and responsibilities,you should contact your nearest authorizedservice center or call Poulan PRO at1 -800 -554 -6723. WHERE TO GET WAR-RANTY SERVICE: Warranty services or repairsshall be provided at all Poulan PRO servicecenters. Call 1 -800 -554 -6723. MAINTE-NANCE, REPLACEMENT AND REPAIR OFEMISSION RELATED PARTS: Any PoulanPRO approved replacement part used in theperformance of any warranty maintenance orrepair on emission related parts will be providedwithout charge to the owner if the part is underwarranty. EMISSION CONTROL WARRANTYPARTS LIST: Carburetor, Ignition System:Spark Plug (covered up to maintenance schedule),Ignition Module, Muffler including Catalyst,Fuel Tank (California only). MAINTENANCESTATEMENT: The owner is responsible for theperformance of all required maintenance as definedintheinstructionmanual.The information on the product label indicates which standard your engine is certified.Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.This engine is certified to be emissions compliant for the following use:Moderate (50 hours)Intermediate (125 hours)Extended (300 hours)-- 14 --