产 品 规 格 书 SPECIFICATION

规 格 书 编 号SPEC NO :产 品 规 格 书SPECIFICATIONCUSTOMER 客 户 :PRODUCT 产 品 :MODEL NO 型 号 :MARKING 印 字 :SAW FILTERHDF915C1 SMD-6HDF6943PREPARED 编 制 : CHECKED 审 核 :APPROVED 批 准 : D A T E 日 期 : 2010-6-1客 户 确 认 CUSTOMER RECEIVED:审 核 CHECKED 批 准 APPROVED 日 期 DATE无 锡 市 好 达 电 子 有 限 公 司Shoulder Electronics Limitedwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 9

SAW FILTERHDF915C1 S6更 改 历 史 记 录History Record更 改 日 期Date规 格 书 编 号Spec. No.产 品 型 号Part No.客 户 产 品 型 号Customer No.更 改 内 容 描 述Modify Content备 注Remarkwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 9

SAW FILTERHDF915C1 S61. Package Dimension2. Marking:HDF6943HD: BrandF : Filter6:SMD-6943 : No.3.Performance3.1ApplicationLow-loss RF filter for remote control receiversCenter Frequency:915 MHz3.2Maximum RatingOperation Temperature Range -40℃ to +85℃Storage Temperature Range -40℃to +85℃DC. Permissive VoltageMaximum Input Power5V DC. max.15dBmwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 9

SAW FILTERHDF915C1 S63.3Electronic CharacteristicsTemperature range for specification: T = –40 °C to +85 °CTerminating source impedance: ZS = 50 WTerminating load impedance: ZL = 50WUnit Minimum Typical MaximumCenter Frequency MHz - 915 -Insertion Loss (902~928MHz) dB 2.4 3.5Amplitude Ripple (902~928MHz) dB 0.9 1.8Relative Attenuation10.0 ~ 800.0 MHz800.0~845.0MHz845.0 MHz ~ 880.0 MHz947.0 MHz ~ 992.0 MHz992.0 MHz ~ 1020.0 MHz1020.0 MHz ~ 1200.0 MHzdB504533253545Input/Output Impedance Ohms 503.4 Frequency Characteristics555043354550-www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 4 of 9

SAW FILTERHDF915C1 S63.5 Test Circuit4. ENVIRONMENTAL CHARACTERISTICS4-1 Temperature cyclingSubject the device to a low temperature of -40℃ for 30 minutes. Following by ahigh temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30Minutes. Then release the device into the room conditions for 1 to 2 hours prior to themeasurement. It shall meet the specifications in 3.3.4-2 Resistance to solder heatSubmerge the device terminals into the solder bath at 260℃±5℃ for 10±1 sec.Then release the device into the room conditions for 4 hours. It shall meet the specificationswww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 5 of 9

SAW FILTERHDF915C1 S6in 3.3.4-3 SolderabilitySubmerge the device terminals into the solder bath at 245℃±5℃ for 5s, More than95% area of the soldering pad must be covered with new solder. It shall meet thespecifications in 3.3.4-4 Mechanical shockDrop the device randomly onto the concrete floor from the height of 1 m 3 times. thefilter shall fulfill the specifications in 3.3.4-5 VibrationSubject the device to the vibration for 2 hour each in x,y and z axes with theamplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 3.3.5. REMARK5.1 Static voltageStatic voltage between signal load & ground may cause deterioration &destruction ofthe component. Please avoid static voltage.5.2 Ultrasonic cleaningUltrasonic vibration may cause deterioration & destruction of the component. Pleaseavoid ultrasonic cleaning5.3 SolderingOnly leads of component may be soldered. Please avoid soldering another part ofcomponent.6. Packing6.1 Dimensions(1) Carrier Tape: Figure 1(2) Reel: Figure 2(3) The product shall be packed properly not to be damaged during transportation and storage.6.2 Reeling Quantity1000 pcs/reel 7’’3000 pcs/reel 13’’6.3 Taping Structure(1) The tape shall be wound around the reel in the direction shown below.www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 9

SAW FILTERHDF915C1 S6(2) LabelDevice NameUser Product NameQuantityLot No.(3) Leader part and vacant position specifications.7. TAPE SPECIFICATIONS7.1 Tensile Strength of Carrier Tape: 4.4N/mm width7.2 Top Cover Tape Adhesion (See the below figure)(1) pull off angle: 0~15º(2) speed: 300mm/min.(3) force: 20~70gwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 7 of 9

SAW FILTERHDF915C1 S6[Figure 1] Carrier Tape DimensionsW F E P0 P1 P2 D0 D1 t1 t2 A B12.0 5.5 1.75 4.0 4.0Ø1.0 0.3 1.253.32.0 Ø1.53.3±± ± ± ± ±± ± ±±±0.05 ±0.10.10.3 0.05 0.1 0.1 0.10.25 0.05 0.10.1[Figure 2][Unit:mm]www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 8 of 9

SAW FILTERHDF915C1 S6www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 9 of 9