Over 110 years of Quality P e rf o rmance and Serv i c e
special application chain - Spinet
special application chain - Spinet
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
STANDARD ATTACHMENT<br />
ROLLER CHAIN<br />
Chain Descriptions <strong>and</strong> Dimensions<br />
www.diamondchain.com<br />
St<strong>and</strong>ard Attachment Roller Chain<br />
Single- <strong>and</strong> Double-Pitch chains are available assembled with either attachment link plates or extended pins. While most carbon steel<br />
attachment chains fall within Diamond’s Attachment Chain Program <strong>and</strong> ship in 48 hours (for quantities up to 100 feet) in 3-5 working<br />
days (for quantities <strong>of</strong> 101 to 300 feet) or in 5-7 working days (for quantities <strong>of</strong> 301 to 500 feet), stainless steel, nickel-plated <strong>and</strong> ACE coated<br />
attachment chains also get special attention through Diamond's 5-day shipping program. These attachments' shapes <strong>and</strong> sizes are "st<strong>and</strong>ard"<br />
their uses are limited only by your imagination. Now the chain that lasts the longest, arrives the fastest because from the minute you place your<br />
order, we have from 48 hours to 5 days to get it out the door. That way you don’t wait -- wasting countless dollars in downtime.<br />
When designing or specifying attachment chains, consider the following information to avoid problems with either<br />
installation or pe<strong>rf</strong>o<strong>rmance</strong>.<br />
St<strong>and</strong>ard Attachments: St<strong>and</strong>ard attachments described on the following pages are normally much less expensive<br />
than special designs. However, if a specialty attachment is necessary please refer to the Made-To-Order section <strong>of</strong><br />
this guide or contact Diamond’s application engineers for possible design options.<br />
Link Plate Location: Attachments, regardless <strong>of</strong> st<strong>and</strong>ard or special design, assembled on pin links are less<br />
expensive than those assembled on roller links.<br />
Modifications: Diamond’s attachment link plates are specifically designed <strong>and</strong> heat treated to permit further operations<br />
by the user such as drilling, reaming, <strong>and</strong> tapping if desired. At no time should attachment links be modified by<br />
welding because the heat applied can adversely affect the heat treatment <strong>of</strong> the steel, resulting in either reduced<br />
pe<strong>rf</strong>o<strong>rmance</strong> or failure.<br />
Extended Pins: Extended pins, made from medium carbon steel, are specially heat treated for ductility <strong>and</strong> toughness<br />
<strong>and</strong> can be easily assembled at virtually any spacing. It is important to note that if pairs <strong>of</strong> extended pins are<br />
specified, they must be located in a common pin link. In some applications this may require the use <strong>of</strong> an <strong>of</strong>fset in the<br />
cycle.<br />
Diamond does not recommend using “shouldered pins.” They are generally expensive to manufacture <strong>and</strong> can <strong>of</strong>ten<br />
compromise quality due to high stress concentrations at the point where diameters change. Additions <strong>of</strong> sleeves or<br />
bearings on the extended pins will <strong>of</strong>ten yield a more dependable design <strong>and</strong> at a lower cost.<br />
Attachment Hole Sizes: Diamond’s st<strong>and</strong>ard attachment hole sizes are designed to accommodate the most<br />
common screw sizes. If your application requires a different attachment hole size, than shown in this section, please<br />
contact Diamond, as many alternate lug holes are available <strong>and</strong> may be available from stock.<br />
Dimensions in Inches<br />
Chain Hole Screw Screw<br />
Size Diameter Size Diameter<br />
25 .125 #3 .099<br />
35 .102 #2 .086<br />
40 .141 #5 .125<br />
41 .141 #5 .125<br />
50 .203 #10 .190<br />
60 .203 #10 .190<br />
80 .266 1<br />
⁄ 4 .250<br />
100 .343 5<br />
⁄ 16 .312<br />
120 .386 3<br />
⁄ 8 .375<br />
140 .448 7<br />
⁄ 16 .438<br />
160 .516 1<br />
⁄ 2 .500<br />
Dimensions in Inches<br />
Chain Hole Screw Screw<br />
Size Diameter* Size Diameter<br />
C2040 .141 # 5 .125<br />
C2050 .203 #10 .190<br />
C2060H .203 #10 .190<br />
C2080H .266 1<br />
⁄ 4 .250<br />
C2100H .328 5<br />
⁄ 16 .312<br />
C2120H .391 3<br />
⁄ 8 .375<br />
C2160H .516 1<br />
⁄ 2 .500<br />
*Straight, one hole attachments have larger diameters than shown. Refer to Double-<br />
Pitch Straight <strong>and</strong> Bent Attachment tables for more detail.<br />
24