USB/PCI Precision Timer Relay Board (PTRB-C) Specifications & Installation Guide

More documents

Recommendations

Info

777 Zapata Drive Fairborn, OH 45324 USA 888.707.4852 Fax: 937-318-2445 E-mail: sales@laserlinc.com www.laserlinc.com 8
1 Specifications Typical for 25°C unless otherwise specified. 1.1 Timer Relay - Control Loop Output Specifications: • Number of loops: PCI CTR-05 – two / PCI CTR-10 – five / PCI CTR-20 - ten USB 4302 – two / USB 4304 - five • Contact configuration FORM C (SPDT) NO, NC and Common available at connector • Contact rating 5 amperes (A) @ 250 volts AC (VAC) or 28 volts DC (VDC) resistive • Will support up to (4) LaserLinc Motorized Potentiometers (MOP) • Contact resistance 100 milliohms max • Operate time 5 milliseconds (ms) max • Release time 2 ms max • Bounce time: 1ms typ. At nom. voltage • Vibration: 10 to 55 hertz (Hz) (Dual amplitude 1.5 millimeters (mm) • Shock: 10 G (11 ms) • Dielectric isolation: 500 V (1 minute) • Life expectancy: 15 million mechanical operations, min • Switch Rate: 360-ops/hr. max at rated load • Power on RESET state: Not energized. NC in contact to Common 1.2 Alarms - Digital Output specifications • Number of outputs: PCI CTR-05 – eight / PCI CTR-10 – eight / PCI CTR-20 – none USB 4302 – eight / USB 4304 – eight • Contact configuration 10 FORM C (SPDT) NO, NC and Common available at connector • Contact rating 5 amperes (A) @ 250 volts AC (VAC) or 28 volts DC (VDC) resistive 777 Zapata Drive Fairborn, OH 45324 USA 888.707.4852 Fax: 937-318-2445 E-mail: sales@laserlinc.com www.laserlinc.com 9
Page 1 and 2: USB/PCI Precision Timer Relay Board
Page 3 and 4: ERRATA: May 25 th , 2010 1) Control
Page 5 and 6: Read Me First: Safety and Electroma
Page 7 and 8: Compliance Electromagnetic Compatib
Page 9 and 10: Conventions - This icon denotes a c
Page 11: Table of Contents 1 SPECIFICATIONS.
Page 15 and 16: 2 Precision Timer / Digital I/O Spe
Page 17 and 18: (8) Input Terminals (+/-) 2-30 VDC
Page 19 and 20: 6) Exit InstaCal. 7) Disable USB Po
Page 21 and 22: 2.4 Installation Procedure PCI - ad
Page 23 and 24: 3 Wiring Procedure 3.1 Digital Inpu
Page 25 and 26: 1. Figure 3-1 Illustration showing
Page 27 and 28: To Voltage Source +/- 2-30 V DC To
Page 29 and 30: Closeup of DIP switch (all on) show
Page 31 and 32: 3.3 Counter (Encoder) Inputs A stan
Page 33 and 34: Apply a voltage differential of bet
Page 35 and 36: 5 Example Configurations 5.1 Digita
Page 37 and 38: 5.1.1 Reset Footage Counter Example
Page 39 and 40: 5.1.3 Using Digital Input to Trigge
Page 41 and 42: 5.1.5 Record Digital Input in Proce
Page 43 and 44: 5.1.7 Record Digital Input in Data

USB/PCI Precision Timer Relay Board (PTRB-C) Specifications & Installation Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?