SUPER COMPACT - SCP

More documents

Recommendations

Info

SCP SUPER COMPACT Installation guidelines INSTALLATION SEQUENCE OF THE JUNCTION The installation instructions are placed on every element near the junction (Fig.1) Make sure that the contacts are clean. 30 mm Join the two elements together. (Fig. 1) (Fig. 2) 270 mm Make sure that the earth plate of the straight element is inserted behind the front plate of the junction monobloc (Fig.2) The positioning pin on the monobloc should be fitted into the corresponding slot on the earth plate. Verify the distance between elements, 270mm, before tightening the monobloc completely (Fig.3). (Fig. 3) Tighten the bolt of the monobloc until the 1st head breaks off (Fig. 4). The bolt that tightens the monobloc has a second head which is used when carrying out operations or inspections on the line. The nominal tightening torque is 85Nm. (Fig. 4) 85Nm Install the covers of the junction (Fig. 5). (Fig. 5) Connection completed correctly with degree of protection IP55 (Fig. 6). For further information, please refer to the technical guide. (Fig. 6) 51 HIGH POWER GENERAL CATALOGUE
Measurement of special element lengths MEASUREMENT OF STRAIGHT ELEMENTS dimension Q N 1 2 3 The exact length of the piece to be ordered can be determined by measuring the distance between the elements (as shown in the picture) and then subtracting 270 mm from the dimension that has been taken. Length of element = Q - 270mm Example: dimension measured = 2500 mm order a 2230 mm element MEASUREMENT OF SPECIAL TRUNKING ELEMENTS B = Q2 - 70 mm HORIZONTAL ELBOW A = Q1 - 70 mm The exact length of the piece to be ordered can be determined by measuring the dimensions Q1 and Q2 (as shown in the picture) and then subtracting 70 mm from each dimension that has been taken. Dimension of the element to order: A = Q1 - 70 mm B = Q2 - 70 mm For further information, please refer to the technical guide. Q1 Q2 52 SUPER COMPACT
Page 1 and 2: SUPER COMPACT - SCP 6 SUPER COMPACT
Page 3 and 4: SCP Features SCP is the Zucchini li
Page 5 and 6: General structural features The out
Page 7 and 8: Main features of the SCP line Strai
Page 9 and 10: Feeder elements FEEDER ELEMENT - ST
Page 11 and 12: Trunking components EXPANSION ELEME
Page 13 and 14: Direction changes HORIZONTAL ELBOW
Page 15 and 16: Direction changes DOUBLE HORIZONTAL
Page 17 and 18: Direction changes DOUBLE ELBOW HORI
Page 19 and 20: Direction changes VERTICAL “T”
Page 21 and 22: Connection interfaces STANDARD CONN
Page 23 and 24: Connection interfaces CONNECTION IN
Page 25 and 26: Connection interfaces CONNECTION IN
Page 27 and 28: Connections interfaces CONNECTION I
Page 29 and 30: Complementary run components SECTIO
Page 31 and 32: Feed units END FEED UNIT Aluminium
Page 33 and 34: Tap-off boxes EMPTY TAP-OFF BOX 125
Page 35 and 36: Tap-off boxes EMPTY TAP-OFF BOX 63A
Page 37 and 38: Fixing supports BRACKETS FOR VERTIC
Page 39 and 40: Transposition element End cover TRA
Page 41 and 42: Operating instructions on how to de
Page 43 and 44: The system: The EdM transformer adv
Page 45: Installation guidelines MINIMUM DIS
Page 49 and 50: 130 Technical data SCP (3L+N+PE) N
Page 51 and 52: 140 SCP Technical Data Functional E
Page 53 and 54: 140 “Double neutral” technical
Page 55 and 56: Suggestions for the project develop

SUPER COMPACT - SCP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?