Camel 6.7' Instructions - Rouse International
Camel 6.7' Instructions - Rouse International
Camel 6.7' Instructions - Rouse International
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
ROUSE<br />
TECHNOLOGIES LLC<br />
This is a Double Layer RMS <strong>Camel</strong>. It uses 348 round latex balloons inflated to 4” in diameter and<br />
44 balloons inflated 3” in diameter to produce a camel design approximately 6.7’ long and 5.7’ tall.<br />
A. Prepare The Matrix.<br />
-- You will find two frameworks in the package like<br />
the one shown above<br />
Stretch Matrix<br />
Unfold Matrix<br />
Hold down the framework with one<br />
hand and lift straight up with the<br />
other to stretch open a small area<br />
at a time. Work your way across the<br />
entire framework.<br />
Spray<br />
paint & extra<br />
Bend Discard adhesive down pop if out on desired. both chips.<br />
sides<br />
If some cuts in the Matrix resist<br />
opening, flex them back and forth<br />
and pull open as shown below.<br />
Bend up on both<br />
sides.<br />
Stretch Matrix<br />
1. 2.<br />
Inflate & size balloons. Tie pairs of the same<br />
size balloons together. (See step “B.) to left.)<br />
NOTE: It is NOT necessary to squeeze balloons<br />
before measuring them. Install pairs of balloons<br />
vertically as shown above in “1.” and “2.”<br />
Continue installing one balloon of each pair in<br />
the first framework ( “3.”) until your design is<br />
complete (”4”).<br />
B. Prepare The Balloons.<br />
Size 348 balloons 4” in diameter<br />
Size 44 balloons 3” in diameter<br />
Tie 4” balloons very close<br />
together.<br />
Trim excess balloon<br />
necks or tie them in<br />
an additional very<br />
loose knot.<br />
3. 4.<br />
The top layer of balloons will be wider than the<br />
lower layer. The lower layer of balloons has<br />
been forced into framework openings.<br />
Tie 3”<br />
balloons far apart.<br />
C. Assemble The <strong>Camel</strong>.<br />
-- Follow general instructions to the right.<br />
-- You may add the second layer as you fill up sections<br />
of the first layer if you prefer.<br />
-- Make sure pairs are vertical when adding second layer.<br />
-- Add colors, details & accessories for more realism.<br />
-- HALF SIZED openings<br />
(in white to right)<br />
get 3” balloons.<br />
-- You may stand the<br />
the RMS <strong>Camel</strong> on the<br />
floor with two base plates<br />
and two vertical poles. Each<br />
pole can slide up between<br />
balloon layers of the camel legs.<br />
5.<br />
* Open and align the<br />
second framework<br />
w i t h t h e f i r s t<br />
framework.<br />
* Press the second<br />
framework down onto<br />
the top layer of<br />
balloons (”5.”).<br />
* Center each balloon<br />
in the frameworks as<br />
shown in (”6.” & “7.”)<br />
6. 7.<br />
USA Patents #6,332,823 & #7,094,124 & #7,507,137. Other patents pending. File: S-CAMEL-H-196A-5L-INSTR Updated: 9/7//2009<br />
© G. <strong>Rouse</strong> 2009 - <strong>Rouse</strong> Technologies LLC - Manufactured & Distributed by <strong>Rouse</strong> <strong>International</strong> LLC, 212 Thomas St., Clemson, SC, USA<br />
Email: info@rouseinternational.com - Tel: 1-877-GO-ROUSE [1-877-467-6873] Toll Free in USA - Tel. <strong>International</strong>: 1-864-654-4166 - Fax: 1-864-654-4051