T-TAPE
t-tape
t-tape
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
T-<strong>TAPE</strong><br />
...anything else is compromise<br />
“T-Tape gives us maximum flexibility of product choice.<br />
We use 15 cm dripper spacing as it provides the most effective<br />
wetting pattern, leading to better crop uniformity and yields.”<br />
David Moon, St George QLD<br />
Water flows through supply<br />
tube & enters inlet filters<br />
Slit outlet opens when<br />
the system is pressurised<br />
to allow flow of water<br />
Inlets built into the tape act as micro-filters<br />
preventing certain contaminants from<br />
entering the emitter flow track<br />
Rivulis<br />
Irrigation<br />
Unique chevron design flow track<br />
creates a turbulent flow to provide<br />
excellent clogging resistance<br />
1800 558 009 (Aus) / +61 7 3881 4071 (intl.)<br />
www.Rivulis.com.au | www.Rivulis.co.nz
T-<strong>TAPE</strong>...<br />
ANYTHING ELSE<br />
IS COMPROMISE<br />
So you might be asking what makes T-Tape so unique?<br />
First there are the number of inlets in every emitter in T-Tape. These small inlets, built directly into the tape, work like microfilters<br />
to help stop contaminants entering the emitter. But because it’s T-Tape, it doesn’t just have a few inlets, T-Tape has up to<br />
211 inlets per emitter! So even if a few get blocked, the tape still keeps going due to the extreme excess redundancy built into<br />
every single emitter.<br />
Still not convinced? How about the reverse chevron flow track? Not just a couple of fancy words, this specially engineered<br />
section keeps the water turbulent and solids in suspension to help prevent the tape from blocking.<br />
Plus, there is the icing on the cake… the knife cut outlet. Instead of laser/hole cut, which some of our (cough!) competitors use, the<br />
knife cut provides a precision incision that closes on shut-off. This makes it hard for dirt to get in, helping to protect your system.<br />
Knife cut outlet<br />
Reverse chevron track<br />
Inlet filters<br />
QUALITY – BECAUSE COMPROMISE IS NOT AN OPTION<br />
Our quality assurance team are very, very serious people! Although they may not be the life of the party (sorry guys!),<br />
their over-the-top attention to detail is what you need for making top quality tape.<br />
Every 4,500 m of T-Tape we manufacture undergoes a computerised flow test, labyrinth fluid path and inlet check, adhesion test<br />
and burst test? Told you... serious testing.<br />
Then because it is your crop (and livelihood) on the line, before dispatching any roll, a second qualified operator must recheck<br />
and sign off every T-Tape roll manufactured.<br />
I LIKE BIG ROLLS & I CANNOT LIE. ..<br />
T-Tape is now available on 570 mm discs, enabling rolls to be 30% on average<br />
longer than standard T-Tape. Make installation easier with fewer joiners, fewer<br />
changeovers while laying with Big Boy Rolls T-Tape.<br />
Caution: Big Boy Rolls weigh more than standard T-Tape rolls. Weights are specified<br />
in the product tables. You may need a couple of big boys to lift Big Boy Rolls.
CLOSE DRIPPER SPACING<br />
Make the best decision for your crops, without the concern of increased costs.<br />
Correct spacing between each drip emitter can make a big difference. Early drip irrigation systems used drippers spaced at<br />
40+ cm intervals. However, this practice has generally been superseded by closer dripper spacing of 10–30 cm intervals due to<br />
the need for more uniform crops and better irrigation system efficiencies.<br />
The benefits of closer dripper spacing are numerous, but are all related to more effective water movement. When irrigating, you<br />
want water to move laterally, not deep down through the soil profile where it is either lost (including any fertilisers added) or<br />
is harder for plants to uptake. By keeping drippers spaced at close intervals, water flows laterally quicker, ensuring a continued<br />
wet strip along the row.<br />
A great thing is when you use T-Tape, closer dripper spacing intervals do not need to come at an extra cost. Because Rivulis T-Tape<br />
has emitters manufactured into the tape itself, as opposed to inserted molded drippers, there is no cost difference per metre<br />
between 10 drippers per metre (10 cm spacing) and two drippers per metre (50 cm spacing).<br />
T-Tape helps make your choice of dripper interval spacing an agronomic decision, not one based on your bank account.<br />
Use close emitter spacing for better crops & system efficiency<br />
Getting your flow & spacing right<br />
A handy rule of thumb — the freer draining the soil, the closer<br />
the emitter spacing needs to be. Therefore in sand, you would<br />
want a relatively close emitter spacing. On the other hand,<br />
in clay, the water will move further laterally allowing you to<br />
use wider drippers. However, keep dripper intervals relatively<br />
close to maximise efficiency of your system, regardless of soil.<br />
Sand Loam Clay<br />
Water movement<br />
Recommended dripper interval spacing<br />
10–20 cm | Strawberries and leafy veg<br />
20–30 cm | All vegies except leafy greens<br />
30 cm | Melons, cane & cotton<br />
Spacing too wide<br />
Spacing correct
DON’T BE THICK ABOUT WALL THICKNESS!<br />
6, 8, 10, 12 OR 15 MIL WALL THICKNESS. ..<br />
HOW TO CHOOSE THE CORRECT ONE?<br />
What is mil wall<br />
thickness?<br />
A mil is an old-school term that<br />
means one thousandth of an inch.<br />
So 6 mil wall thickness means the<br />
tape is 6 thousandths of an inch<br />
thick.<br />
When it comes to tape, sometimes<br />
it is good to be thick! Greater wall<br />
thickness means the tape will last<br />
longer and is more suited for longterm<br />
use, or where there is high<br />
risk of external damage.<br />
Want to go thicker than 15 mil? We<br />
have products for that. However,<br />
for most tape applications<br />
(especially sub-surface), 15 mil is<br />
the most you will need.<br />
6 mil wall thickness (NZ translation: Sucks mul wall thickness bro)<br />
For 6 mil, you want well-cultivated soils where chewing insects are minimal. Generally you<br />
will be using this for single cropping only. Often used for sweet potatoes, onions and lettuce.<br />
8 mil wall thickness<br />
With 8 mil you’ve got a bit more strength, making this one of our most popular tapes for<br />
strawberries, melons and vegetable crops.<br />
10 mil wall thickness<br />
If you’ve got heavy soil and a few insects that fancy a bit of tape, then 10 mil tape will be what<br />
you’re chasing. A great tape for beans, corn, melons and vegetable crops.<br />
12 mil wall thickness<br />
Looking to re-use your tape or grow for multiple seasons, or have chewy insect problems?<br />
Then 12 mil tape is a minimum requirement. You will find 12 mil in sugar cane, cotton and<br />
other sub-surface applications.<br />
15 mil wall thickness<br />
Bring out the big guns with 15 mil tape. This is the stuff you want to use when you’ve got a<br />
swarm of locusts descending on your crop and you want the tape to last a really long time.<br />
We’ve got 15 mil tape in sub-surface sugar cane which is over 20 years old. This stuff is tough<br />
and often used for cane, cotton, young trees and bananas in more permanent applications.<br />
DIAMETERS<br />
500 Series<br />
16 mm – ⅝”<br />
Sometimes size does matter.<br />
Larger T-Tape diameters allow you to run your tape over a<br />
longer distance, and to give you maximum flexibility, T-Tape<br />
is available in four different diameters.<br />
500 and 700 series are our most popular products for<br />
vegetables, melons, strawberries and row crops.<br />
900 series is a great product for longer run lengths of vegies<br />
and row crops such as sugar cane.<br />
1100 series is when you are after some seriously long run<br />
lengths. Think sugar cane and cotton.<br />
700 Series<br />
22 mm – ⅞”<br />
900 Series<br />
29 mm – 1⅛”<br />
1100 Series<br />
35 mm – 1⅜”
EASY PRODUCT IDENTIFICATION<br />
508–30–340<br />
Specifies the series and the<br />
diameter of the tape:<br />
500 series, 5/8” (16 mm)<br />
Specifies the thickness of<br />
the tape: 8 thousandths of<br />
an inch (0.20 mm)<br />
Specifies the spacing<br />
between emitters: 30 cm<br />
Specifies the flow rate per<br />
100 m of tape per hour<br />
@ 55 kPa: 340 lph/100 m<br />
DESIGN & SUPPORT<br />
No pushy sales guys... just a top notch team that is dedicated to assisting you grow more<br />
Call us old-fashioned, but we think the last thing you need is another sales guy who doesn’t<br />
know one end of a tractor from the other flogging you drip tape.<br />
All of our team are experts in their field. From hydraulic design to agronomy, our team is here<br />
to help you achieve more from your irrigation system.<br />
Designing a green field system or new to drip irrigation? Our team can use GPS mapping<br />
equipment to plot your blocks, including elevation data. With this data, our designers can develop<br />
an efficient system customised to your precise requirements.<br />
Need help with installation or irrigation scheduling? We’ve got you covered. With many, many decades of experience (there is<br />
a lot of grey hair on our team), we have the proven track record to deliver irrigation systems that deliver real results.
TYPICAL SYSTEM<br />
CONFIGURATION<br />
PUMP STATION<br />
• Pump (kind of obvious really)<br />
• Primary filters: Rivulis F3200 Screen / F2000 Media F<br />
application) to provide protection to the whole irrig<br />
• Automation & fertigation (if required)<br />
• We recommend a Rivulis ‘stone collector’ or suction<br />
help protect your system. No one likes an eel going<br />
MAIN LINES & SUB MAINS<br />
• Main lines take water to your blocks and sub-mains to the<br />
laterals (i.e. the T-Tape)<br />
• New main lines are generally PVC and buried underground<br />
• Sub-mains are generally either PVC or poly, buried<br />
underground or layflat above ground<br />
• Remember to install Rivulis combination air-valves throughout<br />
to allow air to escape on start up, and to prevent your irrigation<br />
system from imploding on shut-down (not fun)<br />
T-<strong>TAPE</strong><br />
• T-Tape (also known as drip laterals in a<br />
surface, sub-surface or under plastic m<br />
• Diameter, wall thickness, spacing and<br />
crop, topography and water quality. W<br />
configuration suited for your crop
FILTERS & VALVES<br />
ilter (depending on<br />
ation system<br />
strainer pre-pump to<br />
through their pump!<br />
• Primary filtration and valves<br />
• Generally housed in the pump shed<br />
• Provide filtration and control for the entire system<br />
• Use Rivulis V3000 metal valves in the pump shed<br />
• Secondary filtration and valves<br />
• Located in-field<br />
• Valves control individual / sets of blocks. The Rivulis V2000 (plastic)<br />
valve is ideal (and rust proof!)<br />
• In-field filters provide back-up in case something goes wrong in the<br />
main line. Rivulis plastic filters provide economical protection for<br />
your drip irrigation system<br />
MOISTURE MONITORING<br />
design) is installed either onulch<br />
flow rate will depend on your soil,<br />
e can help you choose a T-Tape<br />
• You can’t manage what you can’t measure (copied from a motivational<br />
poster)<br />
• Take the guesswork out of irrigation with Rivulis moisture monitoring<br />
equipment<br />
• GDots: Economical tensiometers with easy to read flip dots<br />
• Plexus: Moisture monitoring that you can view on your phone<br />
with up to 60 field stations per hub
MORE INLET FILTERS THAN<br />
YOU CAN POKE A STICK AT<br />
No one wants blocked tape!<br />
What makes a drip tape less likely to plug? A good starting point is putting as many inlet filters into the<br />
tape as physically possible. These little inlets are designed specifically to help prevent nasty contaminants<br />
making their way into the emitter itself.<br />
Unless you are using bottled spring water from the Swiss Alps as your irrigation water, chances are you are<br />
going to get some funky junk in your tape. Over time, some of this may block up inlet filters – because that’s<br />
what they are designed to do. However, never fear! A unique feature of T-Tape over many other brands with<br />
inserted emitters is the sheer gigantuous number of inlets each emitter has.<br />
The table below highlights the number of inlet filters inbuilt into every single dripper, ranging from 13 in<br />
10 cm spacing T-Tape to 211 in 60 cm T-Tape.<br />
Depending on the configuration, did you know that T-Tape needs as few as 5 inlet filters to work correctly?<br />
Talk about redundancy and peace of mind.<br />
Inlet filters<br />
Product*<br />
Spacing (cm)<br />
Flow (lph / per<br />
emitter)<br />
Flow<br />
(lph / 100 m)<br />
Number of<br />
Inlets per<br />
Emitter<br />
508-10-750 10 0.75 750 13<br />
508-10-1000 10 1.00 1000 13<br />
508-15-170 15 0.25 170 33<br />
508-15-220 15 0.33 220 52<br />
508-15-340 15 0.51 340 30<br />
508-15-500 15 0.75 500 21<br />
508-15-1000 15 1.50 1000 22<br />
510-20-250 20 0.50 250 17<br />
510-20-380 20 0.75 380 17<br />
510-20-500 20 1.00 500 25<br />
508-25-300 25 0.75 300 45<br />
508-25-600 25 1.50 600 62<br />
510-30-170 30 0.50 170 50<br />
510-30-250 30 0.75 250 56<br />
510-30-340 30 1.00 340 65<br />
515-40-250 40 1.00 250 121<br />
515-40-315 40 1.25 315 121<br />
515-60-210 60 1.25 210 211<br />
* The number of inlet filters does not vary between diameters of T-Tape. 500 series product<br />
is specified in this table, but the same specifications also apply to 700, 900 and 1100 series<br />
T-Tape where applicable.
OPERATING PRESSURES,<br />
ROLL DIMENSIONS & WEIGHTS<br />
Mil Thickness Minimum Operating Pressure Maximum Operating Pressure<br />
500 Series (16 mm)<br />
Roll Dimensions of Standard<br />
Size Coils (cm)*<br />
Roll Weight of Standard<br />
Size Coils (kg)*<br />
6 30 kPa 70 kPa 51 x 26 32<br />
8 30 kPa 105 kPa 51 x 26 30<br />
10 30 kPa 105 kPa 51 x 26 30<br />
12 30 kPa 105 kPa 51 x 26 30<br />
15 30 kPa 105 kPa 51 x 26 30<br />
700 Series (22 mm)<br />
6 30 kPa 55 kPa 51 x 26 30<br />
8 30 kPa 70 kPa 51 x 26 30<br />
10 30 kPa 105 kPa 51 x 26 30<br />
12 30 kPa 105 kPa 51 x 26 30<br />
15 30 kPa 105 kPa 51 x 26 30<br />
900 Series (29 mm)<br />
8 30 kPa 55 kPa 51 x 34 33<br />
10 30 kPa 70 kPa 51 x 34 33<br />
12 30 kPa 85 kPa 51 x 34 33<br />
15 30 kPa 105 kPa 51 x 34 33<br />
1100 Series (35 mm)<br />
15 30 kPa 105 kPa 51 x 34 32<br />
* Excludes mini rolls and Big Boy Rolls. All Big Boy Rolls have a diameter of 57 cm and weights are published in the Big Boy Rolls product<br />
section. Mini roll dimensions and weights are dependent on individual product and are available by contacting Rivulis customer service.<br />
FLOW RATES<br />
The flow rates calculated for T-Tape are determined at 55 kPa (0.55 bar). However, in some cases, you may increase pressure, which will in turn<br />
provide a higher flow rate from each dripper. For example, if you run T-Tape with 0.50 lph drippers at 80 kPa, each dripper will emit 0.62 lph.<br />
The table below provides a handy reference of the output per dripper of T-Tape at 80 and 100 kPa.<br />
Dripper Flow Rate (lph)<br />
Based on Nominal Pressure of 55 kPa (0.55bar)<br />
0.25 0.33 0.50 0.75 1.00 1.25 2.00<br />
Flow rate (lph) per emitter @ 80 kPa (0.80 bar) 0.32 0.42 0.62 0.89 1.20 1.47 2.31<br />
Flow rate (lph) per emitter @ 100 kPa (1.00 bar) 0.37 0.49 0.70 1.00 1.35 1.65 2.58
T-<strong>TAPE</strong> 500 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 16 mm (5/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 20<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
506-15-220 16mm (5/8") 6 0.15 15 0.33 220 185 55–70 3050 Custom 101001995<br />
506-10-750 16mm (5/8") 6 0.15 10 0.75 750 85 55–70 3050 Custom 101008273<br />
506-15-170 16mm (5/8") 6 0.15 15 0.25 170 180 55–70 3050 Standard 101001678<br />
506-15-340 16mm (5/8") 6 0.15 15 0.50 340 130 55–70 3050 Standard 101001996<br />
506-15-500 16mm (5/8") 6 0.15 15 0.75 500 110 55–70 3050 Standard 101001679<br />
506-15-1000 16mm (5/8") 6 0.15 15 1.50 1000 75 55–70 3050 Custom WT13088<br />
506-20-125 16mm (5/8") 6 0.15 20 0.25 125 235 55–70 3050 Custom 101001478<br />
506-20-250 16mm (5/8") 6 0.15 20 0.50 250 175 55–70 3050 Standard 101001479<br />
506-25-300 16mm (5/8") 6 0.15 25 0.75 300 155 55–70 3050 Standard 101001997<br />
506-20-380 16mm (5/8") 6 0.15 20 0.75 380 135 55–70 3050 Standard 101001480<br />
506-20-500 16mm (5/8") 6 0.15 20 1.00 500 115 55–70 3050 Standard 101001481<br />
506-30-250 16mm (5/8") 6 0.15 30 0.75 250 175 55–70 3050 Standard 101001485<br />
506-30-170 16mm (5/8") 6 0.15 30 0.50 170 230 55–70 3050 Custom 101001482<br />
506-30-340 16mm (5/8") 6 0.15 30 1.00 340 150 55–70 3050 Custom 101001488<br />
506-40-250 16mm (5/8") 6 0.15 40 1.00 250 175 55–70 3050 Custom 101001691<br />
508-10-1000 16mm (5/8") 8 0.2 10 1.00 1000 75 55–105 2300 Custom 101002004<br />
508-10-1000 | AGS 16mm (5/8") 8 0.2 10 1.00 1000 75 55–105 2300 Custom 101001980<br />
508-10-1000 | AGS (2,000 m roll) 16mm (5/8") 8 0.2 10 1.00 1000 75 55–105 2000 Custom 101001978<br />
508-10-750 16mm (5/8") 8 0.2 10 0.75 750 85 55–105 2300 Standard 101001490<br />
508-15-170 16mm (5/8") 8 0.2 15 0.25 170 180 55–105 2300 Standard WT10311<br />
508-15-220 16mm (5/8") 8 0.2 15 0.33 220 185 55–105 2300 Standard 101002008<br />
508-15-340 16mm (5/8") 8 0.2 15 0.50 340 130 55–105 2300 Custom 101002009<br />
508-15-500 16mm (5/8") 8 0.2 15 0.75 500 110 55–105 2300 Custom 101002012<br />
508-15-1000 16mm (5/8") 8 0.2 15 1.50 1000 75 55–105 2300 Standard 101001491<br />
508-15-1000 | AGS (2,000 m roll) 16mm (5/8") 8 0.2 15 1.50 1000 75 55–105 2000 Custom 101001981<br />
508-20-125 16mm (5/8") 8 0.2 20 0.25 125 235 55–105 2300 Custom 101002013<br />
508-20-250 16mm (5/8") 8 0.2 20 0.50 250 175 55–105 2300 Standard 101001492<br />
508-20-380 16mm (5/8") 8 0.2 20 0.75 380 135 55–105 2300 Standard 101001869<br />
508-20-500 16mm (5/8") 8 0.2 20 1.00 500 115 55–105 2300 Standard 101001494<br />
508-25-300 16mm (5/8") 8 0.2 25 0.75 300 155 55–105 2300 Standard 101002018<br />
508-25-600 16mm (5/8") 8 0.2 25 1.50 600 115 55–105 2300 Standard 101002019<br />
508-30-80 16mm (5/8") 8 0.2 30 0.25 80 300 55–105 2300 Custom 101002020<br />
508-30-170 16mm (5/8") 8 0.2 30 0.50 170 230 55–105 2300 Standard 101001497<br />
508-30-250 16mm (5/8") 8 0.2 30 0.75 250 175 55–105 2300 Standard 101001499<br />
508-30-340 16mm (5/8") 8 0.2 30 1.00 340 150 55–105 2300 Standard 101001500<br />
508-40-250 16mm (5/8") 8 0.2 40 1.00 250 175 55–105 2300 Custom 101001712<br />
508-60-210 16mm (5/8") 8 0.2 60 1.25 210 205 55–105 2300 Custom 101001715<br />
510-10-750 16mm (5/8") 10 0.25 10 0.75 750 85 55–105 1830 Custom 101001506<br />
510-10-1000 16mm (5/8") 10 0.25 10 1.00 1000 75 55–105 1830 Standard 101002024<br />
510-15-1000 16mm (5/8") 10 0.25 15 1.50 1000 75 55–105 1830 Custom 101002025<br />
510-15-220 16mm (5/8") 10 0.25 15 0.33 220 185 55–105 1830 Custom 101002026<br />
510-15-340 16mm (5/8") 10 0.25 15 0.50 340 130 55–105 1830 Standard 101002027<br />
510-15-500 16mm (5/8") 10 0.25 15 0.75 500 110 55–105 1830 Custom 101002028<br />
510-20-250 16mm (5/8") 10 0.25 20 0.50 250 175 55–105 1830 Standard 101001509
T-<strong>TAPE</strong> 500 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 16 mm (5/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 20<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
Continued<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
510-20-380 16mm (5/8") 10 0.25 20 0.75 380 135 55–105 1830 Standard 101001870<br />
510-20-500 16mm (5/8") 10 0.25 20 1.00 500 115 55–105 1830 Standard 101001511<br />
510-25-600 16mm (5/8") 10 0.25 25 1.50 600 115 55–105 1830 Custom 101002031<br />
510-30-170 16mm (5/8") 10 0.25 30 0.50 170 230 55–105 1830 Standard 101001512<br />
510-30-250 16mm (5/8") 10 0.25 30 0.75 250 175 55–105 1830 Standard 101001514<br />
510-30-340 16mm (5/8") 10 0.25 30 1.00 340 150 55–105 1830 Standard 101001515<br />
510-40-125 16mm (5/8") 10 0.25 40 0.50 125 240 55–105 1830 Custom 101001726<br />
510-40-250 16mm (5/8") 10 0.25 40 1.00 250 175 55–105 1830 Custom 101001727<br />
510-40-315 16mm (5/8") 10 0.25 40 1.25 315 160 55–105 1830 Custom 101002032<br />
510-50-400 16mm (5/8") 10 0.25 50 2.00 400 135 55–105 1830 Custom 101002034<br />
510-50-800 16mm (5/8") 10 0.25 50 4.00 800 85 55–105 1830 Custom 101002033<br />
510-60-210 16mm (5/8") 10 0.25 60 1.25 210 205 55–105 1830 Custom 101001730<br />
512-10-1000 16mm (5/8") 12 0.3 10 1.00 1000 75 55–105 1550 Custom 101002038<br />
512-15-500 16mm (5/8") 12 0.3 15 0.75 500 110 55–105 1550 Standard WT14724<br />
512-20-250 16mm (5/8") 12 0.3 20 0.50 250 175 55–105 1550 Custom 101002040<br />
512-20-380 16mm (5/8") 12 0.3 20 0.75 380 135 55–105 1550 Standard 101002041<br />
512-20-500 16mm (5/8") 12 0.3 20 1.00 500 115 55–105 1550 Standard 101001737<br />
512-30-170 16mm (5/8") 12 0.3 30 0.50 170 230 55–105 1550 Custom 101002039<br />
512-30-250 16mm (5/8") 12 0.3 30 0.75 250 175 55–105 1550 Standard 101002043<br />
512-30-340 16mm (5/8") 12 0.3 30 1.00 340 150 55–105 1550 Standard 101001738<br />
512-40-125 16mm (5/8") 12 0.3 40 0.50 125 240 55–105 1550 Custom 101002044<br />
512-40-185 16mm (5/8") 12 0.3 40 0.75 185 215 55–105 1550 Custom 101002045<br />
512-40-250 16mm (5/8") 12 0.3 40 1.00 250 175 55–105 1550 Standard 101001739<br />
512-40-315 16mm (5/8") 12 0.3 40 1.25 315 160 55–105 1550 Standard 101002046<br />
512-50-250 16mm (5/8") 12 0.3 50 1.25 250 175 55–105 1550 Custom 101002047<br />
512-50-400 16mm (5/8") 12 0.3 50 2.00 400 135 55–105 1550 Custom 101002048<br />
512-60-210 16mm (5/8") 12 0.3 60 1.25 210 205 55–105 1550 Custom 101002049<br />
512-75-267 16mm (5/8") 12 0.3 75 2.00 267 175 55–105 1550 Custom 101002050<br />
515-20-250 16mm (5/8") 15 0.38 20 0.50 250 175 55–105 1250 Standard 101001743<br />
515-20-380 16mm (5/8") 15 0.38 20 0.75 380 135 55–105 1250 Standard 101001744<br />
515-20-500 16mm (5/8") 15 0.38 20 1.00 500 115 55–105 1250 Custom 101001745<br />
515-30-170 16mm (5/8") 15 0.38 30 0.50 170 230 55–105 1250 Custom 101002052<br />
515-30-250 16mm (5/8") 15 0.38 30 0.75 250 175 55–105 1250 Custom 101001747<br />
515-30-340 16mm (5/8") 15 0.38 30 1.00 340 150 55–105 1250 Custom 101001748<br />
515-40-125 16mm (5/8") 15 0.38 40 0.50 125 240 55–105 1250 Custom 101001750<br />
515-40-185 16mm (5/8") 15 0.38 40 0.75 185 215 55–105 1250 Custom 101001751<br />
515-40-250 16mm (5/8") 15 0.38 40 1.00 250 175 55–105 1250 Custom 101001752<br />
515-40-315 16mm (5/8") 15 0.38 40 1.25 315 160 55–105 1250 Custom 101002055<br />
515-50-400 16mm (5/8") 15 0.38 50 2.00 400 135 55–105 1250 Standard 101002056<br />
515-50-800 16mm (5/8") 15 0.38 50 4.00 800 85 55–105 1250 Custom 101002057<br />
515-60-210 16mm (5/8") 15 0.38 60 1.25 210 205 55–105 1250 Standard 101001757<br />
515-75-267 16mm (5/8") 15 0.38 75 2.00 267 175 55–105 1250 Custom 101002058<br />
515 Header Hose 16mm (5/8") 15 0.38 - - - - 55–105 1250 Standard 101001343
T-<strong>TAPE</strong> 700 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 22 mm (7/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 20<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
706-15-170 22mm (7/8") 6 0.15 15 0.25 170 405 30–55 2250 Standard 101001767<br />
706-15-220 22mm (7/8") 6 0.15 15 0.33 220 350 30–55 2250 Standard 101002059<br />
706-15-340 22mm (7/8") 6 0.15 15 0.50 340 265 30–55 2250 Custom 101002060<br />
706-20-250 22mm (7/8") 6 0.15 20 0.50 250 310 30–55 2250 Standard 101001521<br />
706-20-380 22mm (7/8") 6 0.15 20 0.75 380 240 30–55 2250 Custom 101002061<br />
706-20-500 22mm (7/8") 6 0.15 20 1.00 500 205 30–55 2250 Custom 101001522<br />
706-25-300 22mm (7/8") 6 0.15 25 0.75 300 280 30–55 2250 Custom 101002063<br />
706-30-170 22mm (7/8") 6 0.15 30 0.50 170 405 30–55 2250 Standard 101001523<br />
706-30-250 22mm (7/8") 6 0.15 30 0.75 250 315 30–55 2250 Custom 101001530<br />
706-30-340 22mm (7/8") 6 0.15 30 1.00 340 265 30–55 2250 Standard 101001532<br />
706-40-250 22mm (7/8") 6 0.15 40 1.00 250 320 30–55 2250 Custom 101001776<br />
708-15-170 22mm (7/8") 8 0.2 15 0.25 170 405 55–70 1695 Custom 101002065<br />
708-15-220 22mm (7/8") 8 0.2 15 0.33 220 350 55–70 1695 Standard 101002066<br />
708-15-340 22mm (7/8") 8 0.2 15 0.50 340 265 55–70 1695 Custom 101002067<br />
708-15-500 22mm (7/8") 8 0.2 15 0.75 500 205 55–70 1695 Custom 101002068<br />
708-20-125 22mm (7/8") 8 0.2 20 0.25 125 415 55–70 1695 Custom 101002069<br />
708-20-250 22mm (7/8") 8 0.2 20 0.50 250 310 55–70 1695 Standard 101001534<br />
708-20-380 22mm (7/8") 8 0.2 20 0.75 380 240 55–70 1695 Custom 101001871<br />
708-20-500 22mm (7/8") 8 0.2 20 1.00 500 205 55–70 1695 Custom 101001535<br />
708-25-300 22mm (7/8") 8 0.2 25 0.75 300 280 55–70 1695 Custom 101002070<br />
708-25-600 22mm (7/8") 8 0.2 25 1.50 600 200 55–70 1695 Custom 101002071<br />
708-30-170 22mm (7/8") 8 0.2 30 0.50 170 405 55–70 1695 Standard 101001536<br />
708-30-250 22mm (7/8") 8 0.2 30 0.75 250 315 55–70 1695 Standard 101001542<br />
708-30-340 22mm (7/8") 8 0.2 30 1.00 340 265 55–70 1695 Standard 101001543<br />
708-40-185 22mm (7/8") 8 0.2 40 0.75 185 390 55–70 1695 Custom 101014482<br />
708-40-250 22mm (7/8") 8 0.2 40 1.00 250 320 55–70 1695 Custom 101001788<br />
710-15-220 22mm (7/8") 10 0.25 15 0.33 220 360 55–105 1340 Standard 101002072<br />
710-15-340 22mm (7/8") 10 0.25 15 0.50 340 265 55–105 1340 Standard 101002078<br />
710-20-250 22mm (7/8") 10 0.25 20 0.50 250 310 55–105 1340 Custom 101001544<br />
710-20-380 22mm (7/8") 10 0.25 20 0.75 380 240 55–105 1340 Standard 101001873<br />
710-20-500 22mm (7/8") 10 0.25 20 1.00 500 205 55–105 1340 Custom 101001545<br />
710-30-170 22mm (7/8") 10 0.25 30 0.50 170 405 55–105 1340 Custom 101001546<br />
710-30-250 22mm (7/8") 10 0.25 30 0.75 250 315 55–105 1340 Standard 101001553<br />
710-30-340 22mm (7/8") 10 0.25 30 1.00 340 265 55–105 1340 Standard 101001554<br />
710-40-315 22mm (7/8") 10 0.25 40 1.25 315 280 55–105 1340 Custom 101002079<br />
710-50-800 22mm (7/8") 10 0.25 50 4.00 800 150 55–105 1340 Custom 101002080<br />
710-60-210 22mm (7/8") 10 0.25 60 1.25 210 365 55–105 1340 Custom 101001804<br />
712-20-250 22mm (7/8") 12 0.3 20 0.50 250 310 55–105 1135 Custom 101002082<br />
712-20-380 22mm (7/8") 12 0.3 20 0.75 380 240 55–105 1135 Standard 101002083<br />
712-20-500 22mm (7/8") 12 0.3 20 1.00 500 205 55–105 1135 Standard 101002084<br />
712-30-170 22mm (7/8") 12 0.3 30 0.50 170 405 55–105 1135 Custom 101002085<br />
712-30-250 22mm (7/8") 12 0.3 30 0.75 250 315 55–105 1135 Standard 101002089<br />
712-30-340 22mm (7/8") 12 0.3 30 1.00 340 265 55–105 1135 Custom 101002090<br />
712-40-125 22mm (7/8") 12 0.3 40 0.50 125 490 55–105 1135 Custom 101002091<br />
712-40-185 22mm (7/8") 12 0.3 40 0.75 185 390 55–105 1135 Custom 101002092
T-<strong>TAPE</strong> 700 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 22 mm (7/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 20<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
712-40-250 22mm (7/8") 12 0.3 40 1.00 250 320 55–105 1135 Standard 101002093<br />
712-40-315 22mm (7/8") 12 0.3 40 1.25 315 280 55–105 1135 Standard 101002094<br />
712-50-400 22mm (7/8") 12 0.3 50 2.00 400 240 55–105 1135 Custom 101002095<br />
712-60-210 22mm (7/8") 12 0.3 60 1.25 210 365 55–105 1135 Custom 101002096<br />
712-75-267 22mm (7/8") 12 0.3 75 2.00 267 310 55–105 1135 Custom 101002097<br />
715-20-380 22mm (7/8") 15 0.38 20 0.75 380 240 55–105 915 Standard 101002108<br />
715-20-500 22mm (7/8") 15 0.38 20 1.00 500 205 55–105 915 Standard 101001806<br />
715-30-170 22mm (7/8") 15 0.38 30 0.50 170 405 55–105 915 Standard 101002119<br />
715-30-250 22mm (7/8") 15 0.38 30 0.75 250 315 55–105 915 Standard 101001814<br />
715-30-340 22mm (7/8") 15 0.38 30 1.02 340 265 55–105 915 Standard 101001815<br />
715-40-185 22mm (7/8") 15 0.38 40 0.75 185 390 55–105 915 Custom 101002111<br />
715-40-250 22mm (7/8") 15 0.38 40 1.00 250 320 55–105 915 Custom 101001818<br />
715-40-315 22mm (7/8") 15 0.38 40 1.25 315 280 55–105 915 Standard 101002113<br />
715-60-210 22mm (7/8") 15 0.38 60 1.25 210 365 55–105 915 Standard 101001819<br />
715-50-400 22mm (7/8") 15 0.38 50 2.00 400 240 55–105 915 Custom 101002115<br />
715-50-800 22mm (7/8") 15 0.38 50 4.00 800 150 55–105 915 Custom 101002114<br />
715-60-350 22mm (7/8") 15 0.38 60 2.10 350 260 55–105 915 Custom 101002116<br />
715-75-267 22mm (7/8") 15 0.38 75 2.00 267 310 55–105 915 Custom 101002117<br />
715-75-533 22mm (7/8") 15 0.38 75 4.00 533 200 55–105 915 Custom 101002118<br />
715 Header Hose 22mm (7/8") 15 0.38 - - - - 55–105 915 Standard 101001348
T-<strong>TAPE</strong> 900 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 29 mm (9/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 16<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
908-15-170 29mm (9/8") 8 0.2 15 0.25 170 530 30–55 1700 Custom 101002120<br />
908-20-125 29mm (9/8") 8 0.2 20 0.25 125 640 30–55 1700 Custom 101002121<br />
908-20-250 29mm (9/8") 8 0.2 20 0.50 250 480 30–55 1700 Standard 101002122<br />
908-20-500 29mm (9/8") 8 0.2 20 1.00 500 320 30–55 1700 Standard 101002123<br />
908-30-250 29mm (9/8") 8 0.2 30 0.75 250 480 30–55 1700 Standard 101002124<br />
908-30-340 29mm (9/8") 8 0.2 30 1.00 340 410 30–55 1700 Standard 101002125<br />
908-40-250 29mm (9/8") 8 0.2 40 1.00 250 480 30–55 1700 Custom 101002127<br />
908-40-315 29mm (9/8") 8 0.2 40 1.25 315 435 30–55 1700 Custom 101002128<br />
908-50-400 29mm (9/8") 8 0.2 50 2.00 400 370 30–55 1700 Custom 101002129<br />
908-60-210 29mm (9/8") 8 0.2 60 1.25 210 560 30–55 1700 Custom 101002130<br />
910-15-220 29mm (9/8") 10 0.25 15 0.33 220 540 55–70 1345 Custom 101002131<br />
910-20-250 29mm (9/8") 10 0.25 20 0.50 250 480 55–70 1345 Standard 101002136<br />
910-20-380 29mm (9/8") 10 0.25 20 0.75 380 370 55–70 1345 Standard 101002137<br />
910-20-500 29mm (9/8") 10 0.25 20 1.00 500 320 55–70 1345 Standard 101002138<br />
910-30-170 29mm (9/8") 10 0.25 30 0.50 170 620 55–70 1345 Custom 101002139<br />
910-30-250 29mm (9/8") 10 0.25 30 0.75 250 480 55–70 1345 Custom 101002140<br />
910-30-340 29mm (9/8") 10 0.25 30 1.00 340 410 55–70 1345 Custom 101002141<br />
910-40-250 29mm (9/8") 10 0.25 40 1.00 250 480 55–70 1345 Custom 101002142<br />
910-40-315 29mm (9/8") 10 0.25 40 1.25 315 435 55–70 1345 Custom 101002143<br />
912-20-250 29mm (9/8") 12 0.3 20 0.50 250 480 55–85 1150 Standard 101002151<br />
912-20-380 29mm (9/8") 12 0.3 20 0.75 380 370 55–85 1150 Standard 101002146<br />
912-20-500 29mm (9/8") 12 0.3 20 1.00 500 320 55–85 1150 Standard 101002147<br />
912-30-170 29mm (9/8") 12 0.3 30 0.50 170 620 55–85 1150 Custom 101047902<br />
912-30-250 29mm (9/8") 12 0.3 30 0.75 250 480 55–85 1150 Custom 101002152<br />
912-30-340 29mm (9/8") 12 0.3 30 1.02 340 410 55–85 1150 Custom 101002153<br />
912-40-185 29mm (9/8") 12 0.3 40 0.75 185 600 55–85 1150 Custom 101002155<br />
912-40-250 29mm (9/8") 12 0.3 40 1.00 250 480 55–85 1150 Custom 101002156<br />
912-40-315 29mm (9/8") 12 0.3 40 1.25 315 435 55–85 1150 Custom 101002157<br />
912-50-400 29mm (9/8") 12 0.3 50 2.00 400 370 55–85 1150 Custom 101002158<br />
912-60-210 29mm (9/8") 12 0.3 60 1.25 210 560 55–85 1150 Custom 101002159<br />
915-20-250 29mm (9/8") 15 0.38 20 0.50 250 480 55–105 925 Custom 101002172<br />
915-20-500 29mm (9/8") 15 0.38 20 1.00 500 320 55–105 925 Custom 101002173<br />
915-30-170 29mm (9/8") 15 0.38 30 0.50 170 620 55–105 925 Custom 101002174<br />
915-30-250 29mm (9/8") 15 0.38 30 0.75 250 480 55–105 925 Custom 101002175<br />
915-30-340 29mm (9/8") 15 0.38 30 1.00 340 410 55–105 925 Standard 101002176<br />
915-40-185 29mm (9/8") 15 0.38 40 0.75 185 600 55–105 925 Custom 101047903<br />
915-40-250 29mm (9/8") 15 0.38 40 1.00 250 480 55–105 925 Custom 101002177<br />
915-40-315 29mm (9/8") 15 0.38 40 1.25 315 435 55–105 925 Custom 101002178<br />
915-50-400 29mm (9/8") 15 0.38 50 2.00 400 370 55–105 925 Custom 101002179<br />
915-60-210 29mm (9/8") 15 0.38 60 1.25 210 560 55–105 925 Custom 101002180<br />
915-60-310 29mm (9/8") 15 0.38 60 1.85 310 425 55–105 925 Custom 101002181<br />
915 Header Hose 29mm (9/8") 15 0.38 - - - - 55–105 925 Standard 101047901
T-<strong>TAPE</strong> 1100 SERIES<br />
SPECIFICATIONS<br />
Nominal diameter 35 mm (11/8")<br />
Flow rate calculated at 55 kPa<br />
Rolls per pallet 16<br />
Description<br />
Nominal<br />
Diameter<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
1115-30-250 35mm (1 1/8") 15 0.38 30 0.75 250 680 55–105 823 Standard 101001829<br />
1115-30-340 35mm (1 1/8") 15 0.38 30 1.02 340 590 55–105 823 Standard 101001830<br />
1115-40-250 35mm (1 1/8") 15 0.38 40 1.00 250 705 55–105 823 Standard 101001832<br />
1115 Header Hose 35mm (1 1/8") 15 0.38 - - - - 55–105 823 Standard 101001350<br />
(lph/<br />
100m)<br />
T- <strong>TAPE</strong> BIG BOY ROLLS<br />
Flow rate calculated at 55 kPa<br />
500/700 series rolls per pallet 20<br />
900/1100 series rolls per pallet 16<br />
Caution: Big Boy Rolls weigh more than standard T-Tape rolls. Weights are specified in the table below.<br />
Other configurations available on request<br />
Description<br />
508-15-220 - Big Boy Roll<br />
(3,000m)<br />
508-20-250 - Big Boy Roll<br />
(3,000m)<br />
508-20-380 - Big Boy Roll<br />
(3,000m)<br />
508-20-500 - Big Boy Roll<br />
(3,000m)<br />
508-30-340 - Big Boy Roll<br />
(3,000m)<br />
510-20-250 - Big Boy Roll<br />
(2,250m)<br />
510-20-380 - Big Boy Roll<br />
(2,250m)<br />
510-20-500 - Big Boy Roll<br />
(2,250m)<br />
510-30-250 - Big Boy Roll<br />
(2250m)<br />
510-30-340 - Big Boy Roll<br />
(2,250m)<br />
512-30-250 - Big Boy Roll<br />
(2,050m)<br />
512-30-340 - Big Boy Roll<br />
(2,050m)<br />
708-30-250 - Big Boy Roll<br />
(2,150m)<br />
708-30-340 - Big Boy Roll<br />
(2,150m)<br />
710-30-250 - Big Boy Rolls<br />
(1,700m)<br />
710-30-340 - Big Boys Rolls<br />
(1,700m)<br />
710-30-250 - Big Boy Roll<br />
(1,830m)<br />
710-30-340 - Big Boy Roll<br />
(1,830m)<br />
1115-30-340 - Big Boy Roll<br />
(1,100m)<br />
Nominal<br />
Diameter<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
22mm<br />
(7/8")<br />
22mm<br />
(7/8")<br />
22mm<br />
(7/8")<br />
22mm<br />
(7/8")<br />
22mm<br />
(7/8")<br />
22mm<br />
(7/8")<br />
35mm (1<br />
1/8")<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
Flow<br />
(lph/per<br />
emitter)<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range<br />
(kPa)<br />
Roll<br />
Length<br />
(m)<br />
Weight<br />
(kg /<br />
roll)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
8 0.20 15 0.33 220 185 55–105 3000 35.0 Standard 101048034<br />
8 0.20 20 0.50 250 175 55–105 3000 35.0 Standard 101048035<br />
8 0.20 20 0.76 380 135 55–105 3000 35.0 Standard 101048036<br />
8 0.20 20 1.00 500 115 55–105 3000 35.0 Standard 101048037<br />
8 0.20 30 1.02 340 150 55–105 3000 35.0 Standard 101048038<br />
10 0.25 20 0.50 250 175 55–105 2250 33.5 Standard 101048200<br />
10 0.25 20 0.76 380 135 55–105 2250 33.5 Standard 101048201<br />
10 0.25 20 1.00 500 115 55–105 2250 33.5 Standard 101048202<br />
10 0.25 30 0.75 250 175 55–105 2250 33.5 Standard 101046418<br />
10 0.25 30 1.02 340 150 55–105 2250 33.5 Standard 101048203<br />
12 0.30 30 0.75 250 175 55–105 2050 36.5 Standard 101048204<br />
12 0.30 30 1.02 340 150 55–105 2050 36.5 Standard 101048205<br />
8 0.20 30 0.75 250 315 55–70 2150 32.5 Standard 101048206<br />
8 0.20 30 1.02 340 265 55–70 2150 32.5 Standard 101048207<br />
10 0.25 30 0.75 250 315 55–105 1700 44.0 Standard 101048208<br />
10 0.25 30 1.02 340 265 55–105 1700 44.0 Standard 101048209<br />
10 0.25 30 0.75 250 315 55–105 1830 47.5 Standard 101048210<br />
10 0.25 30 1.02 340 265 55–105 1830 47.5 Standard 101048211<br />
15 0.38 30 1.02 340 590 55–105 1100 45.0 Standard 101048212
T-<strong>TAPE</strong> MINI ROLLS<br />
SPECIFICATIONS<br />
Nominal diameter 16 mm (5/8”)<br />
Flow rate calculated at 55 kPa<br />
Description<br />
506-10-750 - MINI (610 m roll)<br />
506-20-500 - MINI (610 m roll)<br />
508-10-1000 - MINI (455 m roll)<br />
508-10-750 - MINI (455 m roll)<br />
508-15-500 - MINI (455 m roll)<br />
508-20-500 - MINI (455 m roll)<br />
508-30-340 - MINI (455 m roll)<br />
508-40-250 - MINI (455 m roll)<br />
515-20-500 - MINI (225 m roll)<br />
515-30-340 - MINI (225 m roll)<br />
506-20-500 - SPECIAL (1,000 m<br />
roll)<br />
508-10-750 - SPECIAL (1,000 m<br />
roll)<br />
508-10-1000 | AGS - SPECIAL<br />
(1,000 m roll)<br />
508-15-500 - SPECIAL (1,000 m<br />
roll)<br />
508-20-500 - SPECIAL (1,000 m<br />
roll)<br />
512-10-1000 - SPECIAL (1,000<br />
m roll)<br />
512-10-750 - SPECIAL (1,000 m<br />
roll)<br />
512-20-500 - SPECIAL (1,000 m<br />
roll)<br />
Nominal<br />
Diameter<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
16mm<br />
(5/8")<br />
Nominal<br />
Wall<br />
Thickness<br />
(mil)<br />
(mm)<br />
Spacing<br />
(cm)<br />
(lph/per<br />
emitter)<br />
Flow<br />
(lph/<br />
100m)<br />
Maximum<br />
Run Length<br />
(m) 90%<br />
Emission<br />
Uniformity<br />
Operating<br />
Pressure<br />
Range (kPa)<br />
Roll<br />
Length<br />
(m)<br />
Stocking<br />
Category<br />
Product<br />
Number<br />
6 0.15 10 0.75 750 85 55–70 610 Standard 101002185<br />
6 0.15 20 1.00 500 115 55–70 610 Standard 101002186<br />
8 0.2 10 1.00 1000 75 55–105 455 Standard 101002005<br />
8 0.2 10 0.75 750 85 55–105 455 Standard 101002187<br />
8 0.2 15 0.75 500 110 55–105 455 Standard 101002010<br />
8 0.2 20 1.00 500 115 55–105 455 Standard 101002189<br />
8 0.2 30 1.02 340 155 55–105 455 Standard 101002182<br />
8 0.2 40 1.00 250 175 55–105 455 Standard 101002022<br />
15 0.38 20 1.00 500 115 55–105 225 Standard 101002053<br />
15 0.38 30 1.02 340 150 55–105 225 Standard 101002054<br />
6 0.15 20 1.00 500 115 55–70 1000 Standard 101047900<br />
8 0.2 10 0.75 750 85 55–105 1000 Standard 101002188<br />
8 0.2 10 1.00 1000 75 55–105 1000 Standard 101001979<br />
8 0.2 15 0.75 500 110 55–105 1000 Standard 101002011<br />
8 0.2 20 1.00 500 115 55–105 1000 Standard 101002190<br />
12 0.3 10 1.00 1000 75 55–105 1000 Standard 101002036<br />
12 0.3 10 0.75 750 85 55–105 1000 Standard 101002035<br />
12 0.3 20 1.00 500 115 55–105 1000 Standard 101002042<br />
MORE THAN JUST GREAT PRODUCTS...<br />
At Rivulis we like to keep things pretty simple — great products, on time and good value.<br />
Whether you need irrigation for ag, landscape or greenhouses, we can assist! And we don’t just have great products, we also<br />
offer great irrigation services. We can help sort you out with agronomic irrigation advice, irrigation design, moisture monitoring<br />
and GPS surveying.<br />
This literature has been compiled for worldwide circulation and the descriptions, photos and information are for<br />
general purpose use only. Please consult with an irrigation specialist and technical specifications for proper use of<br />
products. Because some products are not available in all regions, please contact your local dealer for details. Rivulis<br />
Irrigation reserves the right to change specifications and the design of all products without notice.<br />
RIV_DS_T-Tape_AU_EN_201509<br />
Rivulis Irrigation<br />
1800 558 009 (Aus) / +61 7 3881 4071 (intl.)<br />
www.Rivulis.com.au | www.Rivulis.co.nz