combined small

Corrosion 

ProteCtion P O L Y S C R E E D Corrolam solidguard

CONCRETE PROTECTION 

PRODUCT NAME DESCRIPTION AREAS OF APPLICATION/MARKET FOCUS 

CORROLAM 

H05 / VO5 

Trowel applied vinyl ester epoxy resin screed. 

It has high chemical resistance and the system 

is designed for demanding acid or highly 

alkaline environments. Its durability, resistance 

to thermal shock as well as chemical 

resistance is unmatched. 

• Ideal for demanding environments such as acid plants, 

Power Stations, Mining industry bund areas for 

secondary containment areas in processing plants. 

• Exterior containment areas. 

• Can also be used as a chemical resistant tank lining. 

CORROLAM RC 

A chemical resistant vinyl ester roller top coat 

that is used as protection in acid or highly 

alkaline environments. It can be applied over 

existing laminate systems or fibre wound 

tanks as a rejuvenation coat and can also be 

used as a top coat on new laminate systems. 

• Ideal for the protection of concrete walls, equipment 

and tank bases, floors and drains against aggressive 

chemicals in bund areas. 

• Tank linings with aggressive chemicals. 

• Acid bunds, tank linings top coats or rejuvination coats. 

CORROLAM GL 

A chemical resistant epoxy vinyl ester resin 

laminating resin that is also used in demanding 

acid or highly alkaline environments. It is 

applied in combination with glass fibre and 

chemical resistant C glass veil for optimum 

chemical resistance and excellent crack 

bridging capabilities. 

• Ideal for protection of concrete structures, equipment 

bases, floors and drains against aggressive chemicals 

that may experience a high amount of movement. 

• Exterior and interior Acid bunds as well as a range of 

chemical resistant tank linings ie: Chloride dioxide tanks, 

Flue gas scrubbers, acid and alkali tanks. 

CORROLAM UT 

A chemical resistant epoxy vinyl ester system 

with a non-slip screeded finish of Corrolam 

RC vinyl ester sealcoat for optimum chemical 

and slip resistance. 

• Ideal for demanding environments such as Acid plants, 

Power Stations, Mining industry bund areas for 

secondary containment areas in processing plants 

requiring a non-slip finish. 

• Exterior and interior secondary containment areas for 

chemical resistance. 

POLYSCREED HF 

Abrasion and temperature resistant, heavy 

duty trowel applied polyurethane flooring 

system. Polyscreed HF incorporates silver 

ion’s for antimicrobial protection in the food 

environment and is applied between 8 - 

10mm for high wear and abrasion resistance 

as well as excellent temperature resistance of 

up to 140 0 C. 

• Food and beverage wet processing plants ie: Bakeries, 

Butcheries, Bottling Halls, etc. 

• Brewery wet processing areas with high temperature 

requirements. 

• Heavy duty Engineering workshops. 

• Chemical resistance lining for secondary containment 

areas with chemical attack in processing plants, mines 

and high impact areas. 

POLYSCREED RT 

Abrasion, chemical resistant, heavy duty 

flow applied Rake and Trowel polyurethane 

flooring system. Polyscreed RT resin system 

incorporates silver ion’s for antimicrobial protection 

in the food processing environment 

and is applied between 6 - 8mm. Temperature 

resistance of up to 120 0 C. 

• Food and beverage processing plants ie: Bakeries, 

Butcheries, Bottling Halls, Wineries, etc. 

• Brewery processing areas. 

• Heavy duty Engineering workshops. 

• Loading and wash bays. 

POLYSCREED MD 

Abrasion and chemical resistant, medium 

duty flow applied polyurethane flooring system. 

Polyscreed MD is a resin system which 

also incorporates antimicrobial silver ion 

protection and is applied between 3 - 4mm. 

• Storage areas. 

• Dry or wet processing areas. 

• Areas with high fork lift traffic and impact. 

• Automotive manufacturing areas. 

• Packaging areas. 

POLYSCREED WR 

Abrasion and chemical resistant, light weight 

trowel applied polyurethane wall render. This 

resin system incorporates antimicrobial silver 

ion protection. Applied between 2 - 25mm. 

• As a wall render in Food and beverage processing plants. 

• Brewery processing bund areas. 

• Heavy duty Engineering workshops wall covings. 

• Loading and wash bays skirtings and wall applications.

STEEL PROTECTION 

PRODUCT NAME DESCRIPTION AREAS OF APPLICATION/MARKET FOCUS 

SOLIDKOTE 227 

A self-priming, waterbased, water potable 

high-build epoxy coating system. It offers 

excellent corrosion protection to a wide 

variety of substrates in the minimum number 

of coats.Its superior adhesion properties allow 

it to be applied over marginally prepared 

rusted steel surfaces and the solids content 

allows the coating to be applied over existing 

coatings without lifting and wrinkling. It is 

solvent free and VOC compliant. Also 

suitable for potable water applications. 

• Bridges, machinery, structural steel. 

• Tank linings (steel or concrete). 

• Green concrete surface compatible. 

• Tank and piping interior linings. 

• Mining structures. 

• Metal roofing. 

• Offshore equipment, marine environments. 

STEELMASTIC 

168 

An industry standard, surface tolerant, 

self-priming, direct-to-rust, high build epoxy 

mastic coating. Its superior adhesion properties 

allow it to be applied over marginally prepared 

rusted steel and old existing coatings. 

• Excellent maintenance coating for bridges, pipes, fences, 

machinery, structural steel or tank exteriors, especially 

when corrosion of the steel has taken place. 

• Ideal for offshore structures, marine piping and exposed 

steel structures. 

SOLIDGUARD 88 

A rapid curing, surface tolerant, chemical 

resistant high solids epoxy primer, 

intermediate or finish coating for application 

onto steel surfaces. Solidguard 88 provides 

excellent adhesion and corrosion protection 

to mild steel. 

• Ideal for protection of steel tanks, equipment bases, 

floors and drains against aggressive chemicals. 

• Tank farms and chemical storage tanks ideal in Petroleum 

Plants, sugar industry etc. 

• Priming of steel prior to applying ceramic tiles for added 

corrosion protection. 

SOLIDGUARD 

HCP 

An extremely high chemical resistant 

Bisphenol. A ceramic coating that is 

specifically designed for demanding acid 

or highly alkaline environments. Available in 

various colours offering high abrasion and 

scratch resistance. 

• Ideal for protection of concrete tanks, equipment bases, 

floors and drains against aggressive chemicals in extreme 

environments. 

• Tank farms and chemical storage tanks and petroleum 

tanks. 

• Acid bunds, tank linings. 

• Chemical loading bays. 

SOLIDKOTE UVC 

Solidkote UVC is a two component , aliphatic 

polyurethane with excellent UV stablility. It offers 

a high gloss finish. Its weather resistance 

and ability to resist chalking is outstanding. 

The product displays excellent flexibility, high 

abrasion, acid alkali and solvent resistance. 

• Interior or exterior application. 

• For use on concrete floors, structural steel, waste water 

facilities, chemical plants as well as marine application 

above water-line. 

• Ideal coating where outstanding colour and gloss 

retention is mandated. 

• Do not apply over wet / damp surfaces. Ensure a 

complete, dry seal of walls.

PRODUCT GROUP 

CONCENTRATION 

% 

TEMPERATURE 

0 

C 

A b C D E 

Acetic Acid 

10 60 NR NR NR NR VG 

30 20 NR NR E NR VG 

blood – – E E E E E 

Calcium Chloride – – E E E E E 

Calcium 

Hydroxide 

30 – E E E E E 

Citric Acid 30 20 E F E E E 

Copper Sulphate 30 20 E E E E E 

Formic Acid 

30 20 NR NR E NR E 

98 20 NR NR F NR F 

Petrol – – E E E E E 

Hydrofluoric Acid 48 20 NR NR E NR E 

Hydrogen 

Peroxide 

100 20 G F E E E 

Lactic Acid 90 20 NR NR E NR E 

Nitric Acid 

30 20 NR NR E NR E 

69 20 NR NR NR NR NR 

Abbreviations 

Phosphoric Acid 

5 20 E NR E VG E 

50 20 E NR E E E 

Skydrol A500 – – E NR E E E 

Sodium 

Hydroxide 

50 20 E E E E E 

50 60 NR NR NR NR VG 

5 20 E NR E F E 

Sulphuric Acid 

30 20 G NR G NR G 

98 20 NR NR NR NR NR 

Potassium 

Hydroxide 

10 100 E E E E E 

50 20 E E E E E

P O L Y S C R E E D 

Corrolam 

solidguard

TECHNICAL FINISHES COMPANY PROFILE: 

Technical Finishes have been leaders in the field of surface preparation and 

protection since 1989. We specialise in Industrial Flooring materials branching into 

Commercial and residential market sectors too. Technical Finishes have developed 

a reputation for delivering high performance, technically advanced, durable and 

HACCP compliant flooring systems as required by our client’s demands, promptly 

and effectively. 

We pride ourselves in being able to provide solutions for the most corrosive 

environments and conditions such as harsh chemical areas and acid exposure. Our 

product also comply to various legal requirements specific to an industryie: Food 

and beverage, pharmaceutical etc. 

The company currently employs over 80 people on a national basis and offers 

exclusive training of our products to our approved applicators and well as 

technical support to our smaller clients handling residential and commercial 

flooring applications. Site support is also offered to construction houses and 

building contractors. 

We pride ourselves in fast turnaround times for our products due to local 

manufacture. Our team of dedicated industrial chemists keeps us abreast to 

serve a rapidly developing and changing market environment. We pride 

ourselves in continually investing in research and development of new 

technologies and trends, and providing on-going training and skills 

development to our staff. 

We have three fully equipped manufacturing units based in Gauteng, Kwazulu 

Natal and the Western Cape which are fully ISO 9001 certified enabling us to 

better serve the Southern African region. We are proudly South African. 

Our product range covers the following markets: 

 

 

 

 

 

 

Industrial Flooring 

Commercial Flooring 

Residential Flooring 

Concrete repair 

Waterproofing 

Cleaning Chemicals 

Visit our website on www.technicalfinishes.com or contact us directly on ….

Mining Products 

INDEX 

Technical Finishes 

Equivalent 

Coatings 

1. Solidguard 88 Nordcoat 6 

Eposhield HCP 

Nordcoat 1 Special 

Eposhield ST 

Nordcoat 2 + ¼ 

Corrolam VEP GL 

Wearing Compounds 

2. Solidguard LV wearkote Brushable wearing compound 

Solidfix FS Fast set wearing compound Fixwear FS 

Solidwear ST standard set 

Nordtile 

Solidwear HP 100 

Solidwear HP 500 Nordwear 5 

Solidwear HP 800 Nordwear 8 

Adhesives 

3. Solidbond 110 

Solidbond QSP 

Screeds 

4. Solidscreed 49 Damp tolerant and chemical resistant epoxy screed 

Solidscreed LW Light weight epoxy screed for repairs 

Backing Compounds 

5. Solidback HP High performance backing 

Solidback ST 

Standard backing

TECHNICAL DATA SHEET 

SOLIDGUARD 88 

11 August 2016, Rev 2 

SOLIDGUARD 88 

Chemical resistant epoxy steel primer or Top coat 

DESCRIPTION 

Solidguard 88 is a rapid curing chemical resistant high solids epoxy primer or top coat. 

Provides excellent adhesion and corrosion protection to mild steel. Can be used as a primer 

, intermediate or finish coat on steel and has excellent recoat window for overcoating with 

epoxy or polyurethane topcoats. Ideal for tanks exposed to extreme conditions in the pulp 

and paper industry, water pipes sugar industry,mining industry, petroleum industry, Acid 

processing plants and tank farms, etc 

Benefits: 

Excellent adhesion to steel. 

Low temperature cure. 

Extremely tough and crack resistant. 

Excellent corrosion barrier. 

Uses: 

 

 

 

 

Ideal for protection of steel tanks, equipment bases, floors and drains against 

aggressive chemicals. 

Protection of steel water pipes. 

Tank farms and chemical storage tanks. 

Priming of steel prior to applying ceramic tiles for added corrosion protection. 

Substrate requirements: 

Surfaces to be coated must be clean and free of dust, oily residues and loose friable 

material. All steel surfaces to be abrasive blast cleaned to SA2.5 ( ISO 8501-1:2007). If 

oxidation has occurred between blasting and application, the surface must be reblasted. 

Surface defects revealed by blasting , should be ground and filled with Solidbond 120 

epoxy paste. 

Application: 

This is a specialized system that must be installed by an approved applicator . 

Mixing: Materials are supplied as 2 components. Epoxy Part A and Hardener Part B. Mix 

ratio is 4:1 by volume. 

Add components together and mechanically mix for 2 minutes. Use within 60 

minutes. 

Application: Short hair mohair roller or airless spray. If airless spray is used recommended 

spray nozzle is 15 – 21 thou or 0.38 – 0.53mm with 2000 psi pressure. 

Thinners: Only use approved epoxy thinners if necessary. 

Page 1 of 2 

Gauteng Kwa-Zulu Natal Western Cape 

35 Activia Rd, Activia Park, Germiston, 1610 41 Circuit Rd, Westmead 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 

7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDGUARD 88 


TECHNICAL DETAILS: 

Application : Roller or Spray 

Chemical resistance : Consult Technical finishes’ technical department for details. 

Profile 

: Smooth 

Finish 

: Gloss 

Solids : 70% 

Application Temp : 5 - 30ºC 

Spread rate : 8 sqm/litre 

Dry film thickness : 80 micron 

Surface dry at 25 deg C : 45 min 

Over coat 

: min 6hrs : Max 7days 

Dry Film Thickness : 80 microns at 8sqm/L 

Mix Ratio 

: 4:1 by volume 

Colour 

: Red 

Health and safety: They system contains styrene and all appropriate PPE must be worn. 

Please consult Health and Safety Data sheets for each product. 

Technical Finishes products are guaranteed against defective materials and are 

manufactured under high quality standards and are sold subject to its standard Terms and 

Conditions of Sale, copies of which can be obtained on request. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


Eposhield HCP 


EPOSHIELD HCP 

Chemical resistant EPOXY lining resin 

DESCRIPTION 

Eposhield HCP is an extremely chemical resistant Bisphenol-A resin that is specifically designed 

for demanding acid or highly alkaline environments. Also excellent use in Petroleum storage 

tanks. It is applied as a roller coat on steel tanks or in combination with Glass fiber reinforcing 

membrane and chemical resistant C glass veil for optimum chemical resistance. Ideal for tanks 

exposed to extreme conditions in the pulp and paper industry, sugar industry, petroleum industry, 

Acid processing plants and tank farms, etc 

Benefits: 

Excellent chemical resistance to a wide variety of corrosive environments. 

High mechanical properties . 


Excellent scratch and mar resistance / easy to clean. 

Low odour. 

Thermal shock resistant. 

Uses: 

 

 

 

 

 

Ideal for protection of concrete tanks, equipment bases, floors and drains against aggressive 

chemicals. 


Acid bunds, tank linings. 

Chemical loading bays. 

Chemical resistant to 50% Sulphuric acid, 20% HCL , 5% Acetic acid, 30% Sodium 

Hyroxide. 


Surfaces to be coated must be clean and free of dust, oily residues and loose friable material. All 

surfaced to be suitably prepared using grinders, shot blasting or scarifiers to remove laitance. 

Substrate must be a concrete screed Grade 2 evenness and must be a minimum of 20MPa 

compressive strength and must have a tensile pull off exceeding 1.5 Mpa. The substrate should be 

dry to 75% RH (BS 8204) and free from rising damp or ground water pressure. 

Prime with Solidkote STP primer. 

Application: 

This is a specialized system that must be installed by an approved applicator with documented 

quality assurance. Consult Technical Finishes for list of approved applicators. 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


Eposhield HCP 



Application 

: Roller 


Profile 

: Smooth 

Typical Laminate Properties 

Finish : Gloss Glass content: 33% (2 x 450 GSM glass cloth) 

Application Temp : 5 - 30ºC Tensile strength:> 125 Mpa ISO 527-1993 

Service Temperature : 110 ºC max dry Tensile Modulus: > 7800 MPa 

Dry Film Thickness : 1 - 3mm system Flexural strength: > 200 MPa ISO 178-2001 

Colour 

: Various 

Walk on time : 12hrs at 20 ºC 

Full cure 

: 3 days 

System details : Primer Solidkote STP primer and Eposhield HCP and Eposhield HCP 

top coat. Detailed application instructions are available upon request. 

Health and safety: They system contains styrene and all appropriate PPE must be worn. Please 

consult Health and Safety Data sheets for each product. 

Technical Finishes products are guaranteed against defective materials and are manufactured 

under high quality standards and are sold subject to its standard Terms and Conditions of Sale, 

copies of which can be obtained on request. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


Eposhield ST 


EPOSHIELD ST 

SURFACE TOLERANT EPOXY 

DESCRIPTION 

Eposhield ST is an extremely chemical resistant EPOXY resin that is specifically designed for 

demanding applications such as green concrete or high humid conditions. Also excellent use in 

Petroleum storage tanks, Chemical bund areas , breweries , acid plants , sugar mills etc It is applied 

as a roller coat on steel or concrete tanks or in combination with Glass fiber reinforcing membrane 

and chemical resistant C glass veil for optimum chemical resistance. Ideal for tanks exposed to 

extreme conditions in the pulp and paper industry, sugar industry, petroleum industry, Acid 

processing plants and tank farms, etc 

Benefits: 


Can be applied in 98% humidity 




Low odour. 


Uses: 

 

 

 

 

 

Ideal for protection of concrete tanks, equipment bases, floors and drains against aggressive 

chemicals. 


Acid bunds, tank linings. 

Chemical loading bays. 

Chemical resistant to 50% Sulphuric acid, 20% HCL , 5% Acetic acid, 30% Sodium 

Hyroxide. 







Prime with Solidkote STP primer. 

Application: 



Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


Eposhield ST 



Application 

: Roller 


Profile 

: Smooth 

Typical Laminate Properties 

Finish : Gloss Glass content: 33% (2 x 450 GSM glass cloth) 

Application Temp : 5 - 30ºC Tensile strength: > 125 Mpa ISO 527-1993 

Service Temperature : 110 ºC max dry Tensile Modulus: > 7800 MPa 

Dry Film Thickness : 1 - 3mm system Flexural strength: > 200 MPa ISO 178-2001 

Colour 

: Various 

Walk on time : 12hrs at 20 ºC 

Full cure 

: 3 days 

System details : Prime using same resin 

Detailed application instructions are available upon request. 






Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455




CORROLAM VEP GL 

Chemical resistant vinyl ester laminating resin 

DESCRIPTION 

Corrolam VEP RC is an extremely chemical resistant Bisphenol-A epoxy vinyl ester resin that is 

specifically designed for demanding acid or highly alkaline environments. It is applied in 

combination with Glass fiber and chemical resistant C glass veil for optimum chemical reistance. 

Ideal for tanks exposed to extreme conditions in the pulp and paper industry , sugar industry, 

petroleum industry, Flue gas scrubbers, Ozone and bleaching tanks etc 

Benefits : 

Fast curing 





Thixotropic resin 


Uses : 

Ideal for protection of concrete walls, equipment bases, floors and drains against aggressive 

chemicals. 

Thermal resistant. 

Acid bunds, tank linings . 

Chloride dioxide tanks, Flue gas scrubbers, Acid and alkali tanks. 







Application : 



Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455





Application : Roller Chemical resistance:Consult Technical finishes’technical dept for details. 

Profile : Smooth Typical Laminate Properties 

Finish : Gloss Glass content 33% 

Application Temp : 5 - 30ºC Tensile strength : > 125 Mpa ISO 527-1993 

Service Temperature: 110 ºC max dry Tensile Modulus > 7800 MPA 

Dry Film Thickness: 0.5mm - 1mm system Flexural strength : > 200 MPa ISO 178-2001 

Colour 

: Various 

Walk on time : 12hrs at 20 degC 

Full cure : 3 days 

System details : Primer VEP and Corrolam RC top coat. Detailed application instructions 

are available upon request. 






Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDGUARD LV WEARKOTE 



BRUSHABLE WEARING COMPOUND 

DESCRIPTION 

Solidguard LV wearkote is a high performance Silicon Carbide filled ceramic epoxy using new 

generation epoxy technology to combine high impact resistance with abrasion and excellent 

corrosion resistance. Designed as a brushable grade wearing compound . 

Benefits: 

Easy to apply with brush. 

Self priming on shot blasted steel with excellent adhesion. 

Chemical resistance to concentrated acids and alkalis. 

Hard wearing and resistant to abrasive slurries. 

Smooth gloss finish which eliminates “hang up” and turbulence in pump cases and pipes 

Solvent free and non flammable . 

High physical properties. 

100% reactive, no solvents 

Uses: 

 

 

 

Recommended for abrasion resistant coating to pipes and pump casings including 

impellers. 

Protection of slurry chutes , separators and slurry tanks. 

Tank linings where continuous agitation causes erosion of steel. 


Surfaces to be coated must be clean and free of oily residues and loose rust . Recommended 

surface profile is a sweep blast with surface finish of Sa 2.5. BS 7079 Part A1 1989 with surface 

profile 75 micron. 

Application: 




Application : Brushable Compressive: > 80mPa (BS6319) 

Profile : Smooth Flexural Strength: > 30mPa (BS6319) 

Finish : Gloss Bond strength: > 7 MPa on shot blasted steel 

Application Temp : 8 - 30ºC 

Tensile strength: 15mPa (BS6319) 

Service Temperature : 80 ºC max dry 

Dry Film Thickness: 1mm system 2 coats 

Colour : dark grey 

Initial cure : 4hrs at 20 ºC 

Page 1 of 2 


35 Activia Rd, Activia Park, Germiston, 1610 41 Circuit Rd, Westmead, 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 

7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455




Mix ratio 

Practical cure 

Full cure 

Pot life 

Overcoat time 

Coverage 

: mix as supplied. 

: 18hrs 

: 7 days 

: 17 -20 min. at 20 degC 

: 4 – 5 hrs 

: 1.8sqm/ 1.5kg kit at 500 microns. Recommend 2 coats 

Health and safety: The system is non hazardous to health and environment. Please consult 

Health and Safety Data sheets for each product. 




Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDFIX FS WEARING COMPOUND 



High Performance FAST SET Wearing Compound 

DESCRIPTION 

Solidfix FS is a fast set high performance technically advanced wearing compound containing 

graded hi Alumina ceramic fillers, held uniformly in suspension in a blended high performance 

resin system to provide a long lasting lining to plant and equipment subject to a high degree of 

abrasive wear. It is ideal for protecting high wearing areas caused by fine slurries. Contains fine 

crushed angular Aluminium Oxide for optimum wear and packing density. 

Benefits: 

Excellent acid and alkali resistance. 

Fast set , cuts down time to a minimum, as most repairs are done on site. 

Extends life of costly plant and components. 

Easy to mix and apply. It conforms and spreads easily into tight corners and curved surfaces. 

Can be applied to vertical and overhead surfaces and areas in which compound shapes or difficult 

access make the application of other wearing materials impractical. 

Water smoothable – Lightly wetting trowel or gloved hand gives a smooth finish. Rapid 

Cure- Normally ready to use in 6 hrs hours at 25 deg C- less if heat is applied. 

Excellent adhesion to metal and other surfaces under adverse conditions including damp 

surfaces. 

Good low temperature cure down to 5 Degrees C and excellent corrosion resistance. 

Uses: 

Any plant and equipment subject to erosion caused by abrasion from process materials. Common 

areas of application are feed chutes, spigots, pipe elbows, slurry lines, hoppers, chests, settling 

tanks, cyclones pump casings ect. 


Surfaces to be clean, dry and free of rust or mill scale. Grit blasting SA2.5 is recommended. If 

mechanical grinding is used ensure that prepared surface has a rough profile. 

Application: 

Using a steel trowel or gloved hand apply compound at 4mm-6mm thickness or as specified. 

Wipe smooth with hands, which are slightly wet with soapy water. 

Any mixed material will become unusable after 40 minutes. 

To accelerate curing time post cure after compound has gardened by heating to about 40 Degrees 

C for 30 

minutes. 

Resistance 

Resists dilute acids and alkalis, aliphatic solvents and petroleum products, seawater and distilled 

water. 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455





No of components : 2 

Chemical resistance : Acids and alkalis, aliphatic solvents and petroleum products 

Mixing Ratio by volume: 2:1 by volume 

Pot Life (500ml) : 15 – 17 min at 25 degC 

Touch Dry 

: 1 hours 

Practical cure : 2 - 3 hours 

Full Cure 

: 18hrs 

Apply by 

: Trowel or gloved hand 

Theoretical Coverage : 6 ltr/m2 at 6mm 

Hardness : Shore D 85 

Compressive Strength : 100 Mpa ASTM D-695-54 

Tensile Strength : 35 Mpa 

Lap shear 

: > 13 Mpa 

Heat Deflection Temp : 70 Degrees C 

Volume Solids : 100% 

Application Temp : Minimum 5 Degrees C & Maximum 35 Degrees C 

Cleaner 

: Epoxy Thinners 

Shelf Life 

: 12 month 

Health and safety: 

All PPE must be worn at all times. Please consult the relevant Health & Safety Data Sheet available from 

Technical Finishes KZN on request and sent with each delivery. 

Safety Precautions: 

Ensure adequate ventilation in work area. Use protective clothing to avoid skin contact with uncured 

compound at all times. No sparks or naked flame to be permitted in the vicinity while tools and equipment 

are being cleaned with Epoxy Thinners or other flammable products. 

Important Note 

Technical Finishes products are guaranteed against defective materials and manufacture and are sold 

subject to its standard Terms and Conditions of Sale, copies of which can be obtained on request. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDWEAR HP 100 

1 July 2016, Rev 2 


High Performance Epoxy Wearing Compound 

DESCRIPTION 

Solidwear HP100 is a high performance technically advanced epoxy wearing compound containing 

graded hi Alumina ceramic bead fillers, held uniformly in suspension in a blended high 

performance epoxy resin system to provide a long lasting lining to plant and equipment subject to 

a high degree of abrasive wear. 

Benefits: 

Excellent acid resistance > 70% Sulphuric acid. Strong acid blends typically used in mine 

processing. 

Cuts down time to a minimum, as most repairs are done on site. 






Cure- Normally ready to use in 12 hrs hours at normal room temperature- less if heat is 

applied. 


surfaces. 


Uses: 





Surfaces to be clean, dry and free of rust or mill scale. Grit blasting is recommended. If mechanical 

grinding is used ensure that prepared surface has a rough profile. 

Application: 





C for 30 

minutes. 

Resistance 


water. 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455



1 July 2016, Rev 2 



Chemical resistance : Mineral Acids and alkalis, aliphatic solvents and petroleum products 

Mixing Ratio by mass : 8.05 kg: 0.45 kg 

Epoxy: Activator 

Pot Life (500ml) : 25-30 min 

Touch Dry 

: 1 hours 


Full Cure 

: 18hrs 

Apply by 


Theoretical Coverage : 6 ltr/m2 at 6mm 



Lap shear 

: > 13 Mpa 




Cleaner 

: Epoxy Thinners 

Shelf Life 

: 12 month 


Some of the components of this product may be hazardous during mixing and application. Please 

consult the relevant Health & Safety Data Sheet available from Technical Finishes KZN on 

request and sent with each delivery. 


Ensure adequate ventilation in work area. Use protective clothing to avoid skin contact with 

uncured compound at all times. No sparks or naked flame to be permitted in the vicinity while 

tools and equipment are being cleaned with Epoxy Thinners or other flammable products. 


Technical Finishes products are guaranteed against defective materials and manufacture and are 

sold subject to its standard Terms and Conditions of Sale, copies of which can be obtained on 

request. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455





WEARING COMPOUND 

High Performance standart set Wearing Compound 

10kg Part number: 4KSWHP5KIT10 

DESCRIPTION 

SolidWEAR HP 500 is a quick set high performance technically advanced wearing compound 

containing graded high density ceramic fillers, providing excellent wear resistance, impact and 

chemical resistance a long lasting lining to plant and equipment subject to a high degree of abrasive 

wear. It is ideal for protecting high wearing areas caused by fine slurries. Contains fine crushed 

angular fillers for optimum packing and wear resistance. 

Benefits: 

Excellent acid ( up to 50% Sulphuric acid ) and alkali resistance. 






Cure- Normally ready to use in 18 hrs hours at 25 deg C- less if heat is applied. 


surfaces. 


Uses: 







Application: 





C for 30 

minutes. 

Page 1 of 2 


35 Activia Rd, Activia Park, Germiston, 1610 5 Progress Rd, New Germany, 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 

7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455




Resistance 


water. 



Kit size 

: 10 kg 

Coverage 

: 1sqm at 4.5 mm 

Mixing Ratio by volume : 2:1 by volume 

Pot Life (500ml) : 25 - 30 min at 25 degC 

Working time : 45 min. 


Full Cure 

: 18hrs 

Apply by 





Lap shear 

: > 13 Mpa 





Shelf Life 

: 12 month 


All PPE must be worn at all times. Please consult the relevant Health & Safety Data Sheet 

available from Technical Finishes KZN on request and sent with each delivery. 



uncured compound at all times. No sparks or naked flame to be permitted in the vicinity while 

tools and equipment are being cleaned with Epoxy Thinners or other flammable products. 


Technical Finishes products are guaranteed against defective materials and manufacture and are 

sold subject to its standard Terms and Conditions of Sale, copies of which can be obtained on 

request. 

Page 2 of 2 


35 Activia Rd, Activia Park, Germiston, 1610 5 Progress Rd, New Germany, 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 

7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455





WEARING COMPOUND 

High Performance Wearing Compound 

10kg Part number: 4KSWHP8KIT10 

DESCRIPTION 

SolidWEAR HP 500 is a superior high performance technically advanced wearing compound 

using Novalac resin technology for superior temperature, chemical and wear resistance, It 

contains graded high density ceramic fillers creating a “bed” of ceramic for excellent wear 

resistance, impact and chemical resistance.It is ideal for protecting high wearing containing 

acid slurries. Also suitable in Chrome reduction plants. 

Benefits: 

Excellent acid ( up to 70% Sulphuric acid )and alkali resistance. 



Can be applied to vertical and overhead surfaces and areas in which compound shapes or 

difficult access make the application of other wearing materials impractical. 

• Water smoothable – Lightly wetting trowel or gloved hand gives a smooth finish. 

Rapid Cure- Normally ready to use in 18 hrs hours at 25 deg C- less if heat is applied. 

• Excellent adhesion to metal and other surfaces under adverse conditions including 

damp surfaces. 

• Good low temperature cure down to 5 Degrees C and excellent corrosion 

resistance. 

Uses: 

Any plant and equipment subject to erosion caused by abrasion from process materials. 

Common areas of application are feed chutes, spigots, pipe elbows, slurry lines, hoppers, 

chests, settling tanks, cyclones pump casings ect. 




Application: 




To accelerate curing time post cure after compound has gardened by heating to about 40 

Degrees C for 30 

minutes. 

Resistance 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 

7733 Tel: +27 (0) 21 535 

4455




Resists dilute acids and alkalis, aliphatic solvents and petroleum products, seawater and 

distilled water. 



Kit size 

: 10 kg 

Coverage 

: 1sqm at 4.5 mm 

Mixing Ratio by volume : 2:1 by volume 

Pot Life (500ml) : 25 min at 25 degC 

Working time : 35 min. 


Full Cure 

: 18hrs 

Apply by 





Lap shear 

: > 13 Mpa 




Shelf Life 

: 12 month 


All PPE must be worn at all times. Please consult the relevant Health & Safety Data Sheet 

available from Technical Finishes KZN on request and sent with each delivery. 



uncured compound at all times. No sparks or naked flame to be permitted in the vicinity 

while tools and equipment are being cleaned with Epoxy Thinners or other flammable 

products. 


Technical Finishes products are guaranteed against defective materials and manufacture and 

are sold subject to its standard Terms and Conditions of Sale, copies of which can be 

obtained on request. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 

7733 Tel: +27 (0) 21 535 

4455


SOLIDBOND 110SS 

30 June 2016, Rev 2 

SOLIDBOND 110 SS 

CERAMIC TILE PASTE ADHESIVE 

DESCRIPTION 

Solidbond 110 is a solvent free, STANDARD SET epoxy adhesive for bonding high 

alumina ceramics where chemical resistance is required. It may also be used for a wide 

range of adhesive applications where excellent adhesion and high chemical resistance is 

required. 

Benefits: 

Excellent adhesion on steel, ceramic , glass , concrete , GRP . 

Excellent chemical resistance. 

Damp tolerant 

Thixotropic and can be applied to vertical or overhead surfaces. 

Good temperature resistance. Up to 90 deg C 

Ease of mixing : 1:1 mix ratio. 


Surfaces to be treated must be free of dust, oily residues and loose friable material. 


Appearance : Part A – Off white / Part B – brownish Physical Properties 

Pot life : 15 minutes Service Temperature : wet 60 deg C : Dry 90 deg C 

Set : 1 hour Tensile strength : > 50 Mpa 

Mix ratio : 1:1 by volume Compressive strength : > 75 mpa 

Full cure : 24 hours, cure is temp sensitive Bond strength ceramics > 13 Mpa 

Application temperature: 5 - 35 ºC 

Packaging : 2 L kits 

Health and safety: Epoxy products are to be treated with care. In the event of skin 

contact, was well with soap and warm water. Seek medical assistance immediately in 

case of eye contact. Please consult Health and Safety Data sheets for each product. 

Technical Finishes products are guaranteed against defective materials and are 

manufactured under high quality standards and are sold subject to its standard Terms and 

Conditions of Sale, copies of which can be obtained on request. 

Page 1 of 1 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDBOND QSP 


SOLIDBOND QSP 

Quick set paste adhesive 

DESCRIPTION 

Solidbond QSP is a solvent free, epoxy quick set epoxy adhesive for bonding ceramics, acid bricks, 

steel or concrete. It may also be used for a wide range of adhesive applications where rapid set 

and high chemical resistance is required. 

Benefits: 

Excellent chemical resistance – resists attack of petroleum products, acids and alkali. 

Fast curing 

Damp tolerant 

Thixotropic and can be applied to vertical or overhead surfaces. 

Good temperature resistance 

Ease of application 


Surfaces to be treated must be free of dust, oily residues and loose friable material. 


Appearance : Part A – Off white / Part B – brownish Physical Properties 

Pot life : 15 - 20 minutes Service Temperature : wet 60 deg C : Dry 90 deg C 

Set : 1 hour Tensile strength : > 50 Mpa 

Mix ratio : 2:1 by volume Compressive strength : > 75 mpa 

Full cure : 24 hours, cure is temp sensitive Bond strength ceramics > 11 Mpa 

Application temperature : 5 - 35 ºC 

Packaging 

: 1.5 L kits 

Health and safety: Epoxy products are to be treated with care. In the event of skin contact, was 

well with soap and warm water. Seek medical assistance immediately in case of eye contact. 

Please consult Health and Safety Data sheets for each product. 




Page 1 of 1 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDBACK HP 


SOLIDBACK HP 

High performance backing 

DESCRIPTION 

Solidback HP - HI-PERFORMANCE BACKING is a 100% Solids reactive resin system 

for backing metal wear plates in large gyratory crushers and cone crushers. It offers 

excellent impact strength and resilience, together with high compression and tensile 

strengths. It is non-flammable, easy to mix and apply and on curing has no shrinkage which 

eliminates the gaps between backing and liners or support structures. Ideally suited to 

Chrome, Platinum, Manganese and Iron ores to improve liner life. 

BENIFITS 

Non Hazardous 

No molten zinc and peripheral equipment 

100% solids co-polymer system. 

Saves downtime and money. 

Tough and resilient. 

Easy and safe to use. 

PHYSICAL PROPERTIES (all at 25°) 

Compressive strength 

> 110Mpa Suitable for large Gyratory and Cone 

crushers 

Working time 

20 - 25 Minutes 

Gel time 

45 Minutes 

Operational time 

6 Hours 

Mixed colour 

Red 

Kit size 

20kg (12.4 litres) 

APPLICATION INSTRUCTIONS 

Store backing material and concaves between 10°C - 25°C for 24 hours prior to application. 

Backing surface of concaves should be free of rust, dirt, grease and oil. 

Place the first row of concaves and support them in the usual manner. 

Use wood strips around each concave to obtain even spacing. 

A light coating of release agent should be applied to all surfaces of the bowl or mantle to 

facilitate future removal of worn liners. 

N.B DO NOT APPLY RELEASE AGENT ONTO LINERS THEMSELVES 

Seal gaps between cancaves to prevent leakage with Solidfix TROWL MIX. 

If ambient temperatures are expected to be below 16°C, apply heat with torches between 

concaves and the shell to bring the temperature up to the specified level, preferably 32°C, 

but not more than 60°C. 

Premix resin in large pail for one minute using a low speed drill. 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDBACK HP 


While stirring, add hardener contents from the small bottle at a slow continuous rate. 

Move stirrer up and down and around the sides of the pail until the contents are a uniform 

colour. Mix for three minutes. 

Pour the mixture at several locations around the concave ring. 

After the entire row is fully backed, more heat can be applied to the face side of the 

concaves to accelerate curing, while the next row of concaves is being installed. 

SAFE HANDLING PROCEDURES 

SAFETY WARNING 

Provide adequate ventilation and respirators 

Avoid inhaling fumes. 

Personnel are required to use airline respirators when torch cutting or grinding the product. 

Avoid contact with skin and eyes. 

STORAGE CONDITIONS 

Store indoors on pallets at temperatures between 10°C and 35°C 

PROTECTION 

All work is to be done in a well-ventilated area. 

Overalls and eye protection required. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDBACK ST 


SOLIDBACK ST 

Standard backing 

DESCRIPTION 

Solidback ST Standard Backing is tough, resilient and ideal for Cone Crusher 

Gyratory Crushers, Rotating Mills, Pulverisers and other heavy reduction machinery. 

Solidback ST will suit will many types of crushing operations. Suitable for 5 foot crushers 

and Gold, Copper and low strength ores. 

BENIFITS 

Non Hazardous 

No molten zinc and peripheral equipment 

100% solids co-polymer system. 

Saves downtime and money. 

Tough and resilient. 

Easy and safe to use. 

PHYSICAL PROPERTIES (all at 25°) 

Compressive strength 

In excess of 135 Mpa min 

Working time 

10 - 13 Minutes 

Gel time 

20 Minutes @25°C 

Operational time 

6 Hours 

Mixed colour 

Beige 

Kit size 

10kg and 20kg 

MIXING AND POURING INSTRUCTIONS FOR CONE CRUSHERS 

• Premix resin using a low speed power drill (400rpm max) for ± 2 minutes. 

• While stirring, it is important to move stirrer up and down and around the sides of the 

Pail to disperse resin evenly. Mix for ± 2 minutes. (Exercise mixing speeds cause air 

entrapment, resulting in foaming of the product). 

• Add hardener and mix for a further 2 minute or until a uniform colour is achieved. 

• Pour mixture at several locations to ensure even distribution of Solidback ST Backing 

material. 

• In high temperature regions, assembly and pouring of crushers should be done indoors 

to avoid overheating of components, which could result in uneven cured properties. 

Alternatively pours should take place in the early morning. 

• Avoid water contamination during mixing and pouring. 

Page 1 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455


SOLIDBACK ST 


APPLICATION INSTRUCTIONS 

1. A light coating of release agent should be applied to all surfaces of the bowl of 

mantle to facilitate future removal of worn liners. 

N.B DO NOT APPLY RELEASE AGENT ONTO LINERS THEMSELVES 

2. Liners should be positioned in the Crusher in the normal manner and all gaps sealed 

to prevent leakage of the Solidback ST Backing during pouring. 

3. If ambient temperature is below 15°C, the liners as well as the bowl or mantle 

should be preheated to ±25° 

4. Where Crusher downtime is critical, curing time can be reduced by preheating 

contact surface to a maximum of 50°C. 

SAFETY WARNING 

Provide adequate ventilation and respirators 

Avoid inhaling fumes. 

Personnel are required to use airline respirators when torch cutting or grinding the product. 

Avoid contact with skin and eyes. 

STORAGE CONDITIONS 

Store indoors on pallets at temperatures between 10°C and 35°C 

PROTECTION 

All work is to be done in a well-ventilated area. 

Overalls and eye protection required. 

Page 2 of 2 



7475 

Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455

MATERIAL SAFETY DATA SHEET 

SOLIDGUARD ACTIVATOR 

41 Circuit Road, 

Westmead, Kwa-Zulu Natal, 

South Africa 

Tel: +27 (0) 31 7057733 

EMERGENCY: 0832891307 18 August 2016; Rev 1 

1. PRODUCT INFOROMATION 

Trade name: SOLIDGUARD LV ACTIVATOR Chemical abstract no.: Not Available 

Chemical family: Blend 

NIOSH no.: Not Available 

Chemical name: Blend 

Hazchem code: Not Available 

Synonyms: EPOXY CURING AGENT UN no.: 1760 

2. COMPOSITION 

Hazardous components: 

Ingredient CAS no. Percent R Phrase EEC 

Benzyl Alcohol 100-51-6 5 R36/37/38; R22 Xi 

Isophoronediamine (IPD) 2855-13-2 30 - 40 R36/37/38; R22 Xi 

Mixed amines 30 - 40 R 36/37/38 : R22 Xi 

3. HAZARDS IDENTIFICATION 

Main hazard: Possible skin and eye irritant 

Flammability: None 

Chemical hazard: None 

Biological hazard: None 

Reproductive hazard: None 

Health effects – eyes: Reddening, irritation 

Health effects – skin: Skin reddening, irritation 

Health effects – ingestion: Stomach ache, nausea and vomiting 

Health effects – inhalation: None 

Carcinogenicity: None Mutagenicity: None Neurotoxicity: None 

4. FIRST AID MEASURES 

Product in eye: Flush eyes with water and seek medical attention 

Product on skin: Flush with water and remove clothing. Seek medical advice if rash develops 

Product ingestion: DO NOT induce vomiting. Get immediate medical attention 

Product inhaled: Remove to fresh air. Seek medical advice if breathing becomes difficult 

5. FIRE FIGHTING MEASURES 

Extinguishing media: CO 2, Dry chemical, alcohol resistant foam 

Special hazards: May produce CO 2, ammonia gas or nitrogen oxide. 

Protective clothing: Self contained breathing apparatus. 

6. ACCIDENTAL RELEASE MEASURES 

Personal precautions: Wear protective clothing as indicated in section 8 

Environmental precautions: Do not discharge to natural water systems 

Small spills: Collect in a container for disposal and wash areas with clean water 

Large spills: Collect in containers for disposal. Rinse affected areas with clean water to effluent. 

7. HANDLING AND STORAGE 

Please refer to the disclaimer in section 16 at the end of this material safety data sheet. 

TFIMS-03-02-03-F01 Printed Copies Uncontrolled Page 1 of 4





South Africa 

Tel: +27 (0) 31 7057733 


Suitable material: Keep in original containers in well ventilated areas. 

Handling / storage precautions: Keep containers closed and in a dry place away from acids. 

8. EXPOSURE CONTROLS / PERSONAL PROTECTION 

Occupational exposure limits: Keep below OEL with explosion proof ventilation. 

Engineering control measures: Local exhaust systems, natural air flow 

Personal protection – respiratory: Wear respirator if ventilation inadequate 

Personal protection – hand: Nitrile gloves 

Personal protection – eye: Chemical resistant goggles. 

Personal protection – skin: Apron, closed shoes, overalls 

Other protection: Safety showers must be available. 

9. PHYSICAL AND CHEMICAL PROPERTIES 

Appearance: Clear thick liquid 

Odour: Ammonia type odour 

pH: 11.2 

Boiling point: >100C 

Melting point: Not known 

Flash point: 104C 

Flammability: No 

Autoflammability: No 

Explosive properties: No 

Oxidizing properties: No 

Vapour pressure: 17.70 mmHg at 21C 

Density: 1.3 

Solubility – water: Yes 

Solubility – solvent: No 

Solubility – coefficient: Not known 

Neurotoxicity: No 

10. STABILITY AND REACTIVITY 

Conditions to avoid: Humid, hot conditions 

Incompatible materials: Strong organic acids and alkalis, oxidizing agents. 

Hazardous decomposition products: Carbon monoxide, ammonia, nitrogen oxide. 

11. TOXICOLOGICAL INFORMATION 

Acute toxicity: Oral LD50 - rat: 500-2000mg/kg; Dermal LD50 - rabbit: >2000 mg/kg 

Skin and eye contact: Irritating to skin and eye (rabbit) 

Chronic toxicity: Not known 

Carcinogenicity: None 

Mutagenicity: None 

Neurotoxicity: None 

Reproductive hazardous: None 

12. ECOLOGICAL INFORMATION 







South Africa 

Tel: +27 (0) 31 7057733 


Aquatic toxicity – fish: Not known 

Aquatic toxicity – daphnia: Not known 

Aquatic toxicity – algae: Not known 

Biodegradability: Not known 

Mobility: No 

German wgk: Not Available 

13. DISPOSAL CONSIDERATIONS 

Disposal methods: Dispose of as chemical waste at approved landfill sites 

Disposal of packaging: Rinse and recycle or dispose of at approved landfill sites 

14. TRANSPORT INFORMATION 

UN no.: 1760 

Substance identity no.: Amines n.o.s. 

ADR/RID class: Not available 

ADR/RID item no.: Not available 

ADR/RID hazard identity no.: Not available 

IMDG – shipping name: Amines n.o.s. 

IMDG – class: 8 

IMDG – packaging group: III 

IMDG – marine pollutant: Not available 

IMDG – EMS no.: Not available 

IMDG – MFAG table no.: Not available 

IATA – shipping name: Not available 

IATA – class: Not available 

IATA – subsidiary risk(s): Not available 

ADNR – class: Not available 

UK – description: Not available 


UK – emergency action class: Not available 

UK – classification: Not available 

Tremcard no.: Not available 

15. REGULATORY INFORMATION 

EEC hazard classification: Xi 

Risk phrases: R36/37/38; R22 

Safety phrases: S7, S24/25 

National legislation: None 







South Africa 

Tel: +27 (0) 31 7057733 


16. OTHER INFORMAION 

Technical Finishes (PTY) Ltd provides the information contained herein in good faith but makes no representation 

as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate 

precautionary handling of the material by a properly trained person using this product. Individuals receiving the 

information must exercise their independent judgment in determining its appropriateness for a particular purpose. 

TECHNICAL FINISHES (PTY) LTD MAKES NO REPRESENTATIONS OR WARRANTIES, EITHER 

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF 

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE 

INFORMATION SET FORTH HEREIN OR THE PRODUCT TO WHICH THE INFORMATION REFERS. 

ACCORDINGLY, TECHNICAL FINISHES (PTY) LTD WILL NOT BE RESPONSIBLE FOR DAMAGES 

RESULTING FROM USE OF OR RELIANCE UPON THIS INFORMATION. 





5 Progress Road, 

New Germany, Kwa-Zulu Natal, 

South Africa 

Tel: +27 (0) 31 7057733 EMERGENCY: 0832891307 18 August 2016; Rev 1 


Trade name: SOLIDGUARD LV WEARKOTE EPOXY Chemical abstract no.: Not Available 

Chemical family: Mixture 


Chemical name: Mixture 


Synonyms: Epoxy Resin UN no.: 3082 




Epichlorohydrin & Bisphenol A 

SILICON CARBIDE FILLERS 


025085-99-8 60 -70 

30 – 35 

R38, R43, R52 Xi 

Main hazard: Skin and eye irritant 






Health effects – skin: Skin reddening, significant irritation with possible sensitization 



Carcinogenicity: Not classified as a carcinogen but there is evidence for carcinogenicity 





Product on skin: Flush with water and remove clothing. Seek medical advice if irritation develops 

Product ingestion: Do not induce vomiting. Get immediate medical attention 



Extinguishing media: Dry Powder or C02 

Special hazards: None 

Protective clothing: Yes 







Suitable material: Keep in original containers 






South Africa 


Handling / storage precautions: Keep containers closed and in a dry place 



Occupational exposure limits: None 


Personal protection – respiratory: None 

Personal protection – hand: Rubber gloves 

Personal protection – eye: Not expected to be necessary 


Other protection: None 


Appearance: paste 

Odour: Resin odour 

pH: Not applicable 

Boiling point: Not applicable 

Melting point: Not applicable 



Autoflammability: None 

Explosive properties: None 

Oxidizing properties: None 

Vapour pressure: None 

Density: 1.4 

Solubility – water: No 

Solubility – solvent: Yes 




Conditions to avoid: Heat 

Incompatible materials: Strong organic acids and alkalis, oxidizing materials 

Hazardous decomposition products: Carbon monoxide, phenolics 


Acute toxicity: Not known 

Skin and eye contact: Not known 







Aquatic toxicity – fish: 3.1mg/l (fathead minnow) 

Aquatic toxicity – daphnia: 1.3mg/l 


Biodegradability: Natural materials 

Mobility: No 






South Africa 








UN no.: 3082 

Substance identity no.: Environmentally Hazardous Liquid n.o.s. 

ADR/RID class: Not Available 

ADR/RID item no.: Not Available 

ADR/RID hazard identity no.: Not Available 

IMDG – shipping name: Environmentally Hazardous Liquid n.o.s. 



IMDG – marine pollutant: Not Available 

IMDG – EMS no.: Not Available 

IMDG – MFAG table no.: Not Available 

IATA – shipping name: Not Available 

Tremcard no.: Not Available 



Risk phrases: R38, R43, R52 

Safety phrases: S2, S24/25, S37 








South Africa 
















SOLIDWEAR HP100 ACTIVATOR 

ACTIVATOR 

41 Circuit Rd, 

Westmead , Kwa-Zulu Natal, 

South Africa 



Trade name: SOLIDWEAR HP100 ACT 

Chemical abstract no.: Not Available 





Synonyms: AMINE CURING AGENT UN no.: 1760 




Benzyl Alcohol 100-51-6



ACTIVATOR 



South Africa 












Appearance: Brown Liquid 


pH: 11.2 

Boiling point: >NA 


Flash point: >270 






Density: 1.1 

Solubility – water: NO 

Solubility – solvent:Yes 























ACTIVATOR 



South Africa 



Mobility: No 






UN no.: 1760 





























ACTIVATOR 



South Africa 
















SOLIDWEAR HP100 EPOXY 



South Africa 



Trade name: SOLIDWEAR HP100 











ALUMINIUM OXIDE FILLERS 


025085-99-8 25 - 30 

60 -65 

R38, R43, R52 Xi 

































South Africa 














Appearance: Black paste 











Density: 2.7 


























South Africa 



Mobility: No 







UN no.: 3082 
























South Africa 

















ACTIVATOR 



South Africa 
















ACTIVATOR 



South Africa 












Appearance: RED PASTE 


pH: 11.2 









Density: 2.2 

























ACTIVATOR 



South Africa 



Mobility: No 






UN no.: 1760 





























ACTIVATOR 



South Africa 

















41 Circuit Rd , 


South Africa 
















025085-99-8 25 - 30 

60 -65 

R38, R43, R52 Xi 

































South Africa 

























Density: 2.7 


























South Africa 



Mobility: No 







UN no.: 3082 
























South Africa 

















ACTIVATOR 

41 Circuit Rd 


South Africa 
















ACTIVATOR 

41 Circuit Rd 


South Africa 












Appearance: RED PASTE 


pH: 11.2 









Density: 2.2 

























ACTIVATOR 

41 Circuit Rd 


South Africa 



Mobility: No 






UN no.: 1760 





























ACTIVATOR 

41 Circuit Rd 


South Africa 



















South Africa 
















025085-99-8 25 - 30 

60 -65 

R38, R43, R52 Xi 

































South Africa 

























Density: 2.7 


























South Africa 



Mobility: No 







UN no.: 3082 
























South Africa

combined small

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?