İHTİYACLARİM BURADA PRODUCTS CATALOG

CEMENT CATEGORY

PORTLAND CEMENT CEM I 42,5R
Product
Portland Cement
Standard
TS EN 197-1:2002
Product Definition : Portland cement is a product which is obtained as clinker resulting from mixing at suitable rates,
grinding and firing raw materials such as limestone, marl, clay, iron ore, pyrite ash, bauxite, etc. and a certain amount of
setting regulator (generally gypsum) are ground together and sets after mixing with water and gains strength.
In general, it is used in buildings requiring high early strength, concrete poured in cold weather, prefabricated buildings,
tunnel-mould applications, construction chemicals production and foundation applications.

PORTLAND CEMENT CEM I 42,5R
Physical Properties
Cement Standard Unit
Chemical Properties
Cement Standard Unit
Initial Set 165 min. 60 minute
Final Set 260 - minute
Initial Set 3,13 - g/cm3
SO3 2,65 maks. 4,0 %
MgO 1,15 - %
Loss of
Ignition
3,30 maks. 5,0 %
Volume
Expansion
1,1 maks. 10 cm
Insoluble
Residue
0,34 maks. 5,0 %
2-Day
Strength
28-Day
Strength
26,2 min. 20 MPa
59,5
min./mak
s.
42,5/62,5
MP
Cl- < 0,01 maks. 0,1 %
Total Alkali
Na2O + 0.658
K2O
0,65 - %
Free Lime 0,95 - %

PORTLAND CEMENT CEM I 52,5N
Product
Portland Cement, CEM I 52,5 N
Standard
TS EN 197-1:2002
Product Definition
Portland cement is a product which is obtained as clinker resulting from mixing at suitable rates,
grinding and firing raw materials such as limestone, marl, clay, iron ore, pyrite ash, bauxite, etc.
and a certain amount of setting regulator (generally gypsum) are ground together and sets after
mixing with water and gains strength.
In general, it is used in buildings requiring high early strength, concrete poured in cold weather,
prefabricated buildings, tunnel-mould applications, construction chemicals production and
foundation applications.

PORTLAND CEMENT CEM I 52,5N
Physical Properties
Chemical Properties
Cement Standard(1) Unit
Cement Standard(1) Unit
Initial Set 170 min. 45 minute
Final Set 260 - minute
Specific
Gravity
3,15 - g/cm3
SO3 * 2,51 maks. 4,0 %
S2-* 0,01 maks.0.20 %
MgO* 1,30 maks. 3 %
Al2O3* 4.54 maks. 8
Loss of Ignition 2,70 maks. 5,0 %
Insoluble Residue 0,32 maks. 5,0 %
Volume
Expansion*
2-Day
Strength
28-Day
Strength
1,1 maks.10 mm.
288 min. 20 MPa
61,4 min. 52,5 MPa
Cl- < 0,01 maks. 0,1 %
Total Alkali
(Na2O + 0.658
K2O)
0,65 maks. 0,1 %
Free Lime 1,05 - %
C3A* 6,24 maks.10 %
[C3A + 0.27 C3S]* 21,91 maks.23,5 %

PORTLAND CEMENT CEM I 52,5R
Product
Portland Cement
Standard
TS EN 197-1:2002
Product Definition
Portland cement is a product which is obtained as clinker resulting from mixing at suitable rates,
grinding and firing raw materials such as limestone, marl, clay, iron ore, pyrite ash, bauxite, etc. and a
certain amount of setting regulator (generally gypsum) are ground together and sets after mixing with
water and gains strength.
In general, it is used in buildings requiring high early strength, concrete poured in cold weather,
prefabricated buildings, tunnel-mould applications, construction chemicals production and
foundation applications.

PORTLAND CEMENT CEM I 52,5R
Physical Properties
Chemical Properties
Cement Standard Unit
Cement Standard Unit
Initial Set 165 min. 45 minute
Final Set 275 - minute
Specific
Gravity
Volume
Expansion
3,15 - g/cm3
1,1 maks. 10 mm
SO3 2,48 maks. 4,0 %
MgO 1,35 - %
Loss of
Ignition
Insoluble
Residue
2,56 maks. 5,0 %
0,34 maks. 5,0 %
Cl- < 0,01 maks. 0.1 %
2-Day
Strength
31,7 min. 30 MPa
Total Alkali
(Na2O +
0.658 K2O)
0,69 - %
28-Day
Strength
63,1 min. 52,5 MPa
Free Lime 1,13 - %

PORTLAND COMPOSİTE CEMENT CEM II / B-M (P-L) 42,5N
Product
Portland Composite Cement
Standard
TS EN 197-1:2002
Product Definition
A product that is obtained as mineral additives (trass) at a rate defined in its standards
(maximum 30%) and Portland cement clinker are ground with a certain amount of setting
regulator (gypsum) and sets after mixing with water and gains strength.
In general, it can be used in all applications for which Portland cement is used. Compared to
Portland cement, it has a relatively lower hydration temperature. It is suitable for using in
concrete works performed in aggressive environments containing ions such as sulphate and/or
chloride, etc.

PORTLAND COMPOSİTE CEMENT CEM II / B-M (P-L) 42,5N
Physical Properties
Chemical Properties
Cement Standard Unit
Initial Set 180 min. 60 minute
Cement Standard Unit
Final Set
270 - minute
Volume
Expansion
2-Day
Strength
1,0 maks. 10 cm
24,3 min. 10 MPa
SO3 2,52 maks. 3,5 %
28-Day
Strength
53,7
min./maks.
42,5/62,5
MPa
Cl- < 0,01 maks. 0,1 %

PORTLAN COMPOSİTE CEMENT CEM II / A-M (PL) 42,5R
Product
Portland Composite Cement
Standard
TS EN 197-1:2002
Product Definition
A product that is obtained as mineral additives (trass) at a rate defined in its standards
(maximum 20%) and Portland cement clinker are ground with a certain amount of setting
regulator (gypsum) and sets after mixing with water and gains strength.
In general, it can be used in all applications for which Portland cement is used. Compared to
Portland cement, it has a relatively lower hydration temperature. It is suitable for using in
concrete works performed in aggressive environments containing ions such as sulphate and/or
chloride, etc.

PORTLAN COMPOSİTE CEMENT CEM II / A-M (PL) 42,5R
Physical Properties
Chemical Properties
Cement Standard Unit
Initial Set 175 min. 60 minute
Cement Standard Unit
Final Set
270 - minute
Volume
Expansion
2-Day
Strength
1,0 maks. 10 cm
25,9 min. 20 MPa
SO3 2,58 maks. 4,0 %
28-Day
Strength
57,2
min./maks.
42,5/62,5
MPa
Cl < 0,01 maks. 0,1 %

POZZOLAİC CEMENT CEM IV / B (P) 32,5N
Product
Pozzolanic Cement
Standard
TS EN 197-1:2002
Product Definition
A product that is obtained as mineral additives (pozzolan) at a rate defined in its standards
(maximum 55%) and Portland cement clinker are ground with a certain amount of setting
regulator (gypsum) and sets after mixing with water and gains strength.
Compared to Portland cement (CEM I 42,5 R and CEM I 52,5 N) and Portland composite cement
(CEM II / A-M (P-L) 42,5 R), it gains strength slower. Besides, water/cement rates are relatively
higher. It is more resistant to alkali-aggregate reaction and chemical external effects. In general,
it is used in repair works in buildings, plaster preparation and construction chemicals
production.

CEM IV / B (P) 32,5N
Cement Standard Unit
Initial Set 195 min. 75 minute
Final Set 290 - minute
Volume Expansion 1,1 maks. 10 cm
2-Day Strength 24,1 min. 10 MPa
28-Day Strength 37,8
min./maks.
32,5/52,5
MPa

CATEGORY IRON AND STEEL

SLAB
Steel slabs are created directly from continuous casting or indirectly
by rolling an ingot. Usage : They are used for manufacture of coils,
sheets and other flat- rolled steel products.
Steel slabs are created directly from continuous casting or
indirectly by rolling an ingot.
Usage : They are used for manufacture of coils, sheets and other
flat- rolled steel products.

BİLLET
Print page
Billets are created directly via continuous casting or extrusion or indirectly via rolling
an ingot. They are in shape of rectangular, circular or square. Usage : They are used
for manufacture of bars, rods, wire and wire products, etc..
STEEL BILLET / BILLETTE
Quality / Qualité: DIN 17100, TS 708, ASTM A 615, JISO3112 (1985)
NFA 35 - 16 (1986) Equivalent Standarts 20 MnSi,
All Desired Chemical Compositions can be met. Tous les compositions
chimique demandées peuvent étre assurées.
Length / Lounguer: 3,5 - 15 Meters
SIZE (mm)
80 x 80 100 x 100 110 x 110 110 x 110
120 x 120 125 x 125 130 x 130 150 x 150
180 x 180 200 x 200

BLOOM
Blooms are similar to billets except the crosssectional
area is greater than 36 sq in.
Common final products include building beams,
rails, rods, and seamless pipes.

HOT ROLLED SHEETS PRİNT PAGE
• Hot Rolled Coils/Bobines laminées a chaud
• Thickness (Epaisseur): Between (entre) 1,2-10 mm
• Hot Rolled Sheets/Toles laminées a chaud
• Thickness (Epaisseur): Between (entre) 1,2-40 mm
• Width/Larguer:1000-2000 mm Length/Longuer: 1000-
6000 mm
• With bundles of 3-10 Tons (Avec des paquests de 3-10
Tonnes

COLD ROLLED SHEETS PRİNT PAGE
Thickness (Epaisseur): Between (entre) 0,3-2,5 mm At desired
dimensions steel sheets, steel strips and steel coils Defferentes
diemensions de toles et de bobines sur commente.

HOT RORLLED COİLS PRİNT PAGE
Hot Rolled Coils/Bobines laminées a chaud
Thickness (Epaisseur): Between (entre) 1,2-10 mm
Hot Rolled Sheets/Toles laminées a chaud
Thickness (Epaisseur): Between (entre) 1,2-40 mm
Width/Larguer:1000-2000 mm Length/Longuer: 1000-6000 mm
With bundles of 3-10 Tons (Avec des paquests de 3-10 Tonnes

COLD ROLLED COİLS PRİNT PAGE
Thickness (Epaisseur): Between (entre) 0,3-2,5 mm At desired
dimensions steel sheets, steel strips and steel coils Defferentes
diemensions de toles et de bobines sur commente.

HOT DİPPED GALVANİZED SHEETS / COİLS PRİNT PAGE
OUR SERVİCES AT A GLANCE
Steel Grades Galvanized Pickled
Soft steels for cold
forming
EN 10346
DX51D - DX53D
EN 10111
DD11 - DD14
Steels for use
construction
EN 10346
S220gd - S550GD
EN 10025-2
S235 - S355
Steels with higher yield
strength for cold
forming
EN 10346
HX300LAD - HX 500LAD
HX550LAD -HX700LAD *)
EN 10149-2
S315MC - S700MC
Special features
Special steels and steels with special alloys upen
request

COATED SHEETS
COATED STEEL COİLS
ALUZİNC

REİNFORCİNG BARS
Print page
Length / Lounger: 6 Meters up to 16 Meters
Size / Dimension: Once folded bundles available / Epingle de nourrice avec
convenable paquets 6 mm. (Could drawned / Laminé á froid) up to jusqu' á 50 mm.
American
Standards
Canadian
Standards
Euronorm
British
Standards
German
Standards
Portuguese
Standards
Israeli
Standards
Ethiopian
Standards
Japanies
Standards
Korean
Standards

MESH
TYPES
PITCH (mm)
MESH
DIAMETER
(mm)
CROSS-SEC
(cm/mm)
Line Cross Line Cross Line Cross
WİRE RODS
R 106 150 250 4.5 4.5 1.06 0.64
R 131 150 250 5.0 5.0 1.31 0.78
R 158 150 250 4.5 5.0 1.58 0.78
R 188 150 250 6.0 5.0 1.88 0.78
R 221 150 250 6.5 5.0 2.21 0.78
R 257 150 250 7.0 5.0 2.57 0.78
R 295 150 250 7.5 5.0 2.95 0.78
R 317 150 250 5.5 d 5.0 3.17 0.78
R 355 150 250 8.0 5.0 3.65 0.78
R 377 150 250 6.0 d 5.0 2.37 0.78
R 443 150 250 6.5 d 5.5 4.43 0.95
R 513 150 250 7.0 d 6.0 5.13 1.11
R 589 150 250 7.5 d 6.5 5.89 1.33

WELDED TUBES
INDUSTRIAL WELDED PIPES
Dimensions and conventional masses per unit length of pipes
Les dimensionsns et les masses standat en unite de longuer-tube
Quality / Qualité : DIN 2458

STAİNLESS STEEL