XRAY T1 EVO2.pdf - Minicars Hobby AB
XRAY T1 EVO2.pdf - Minicars Hobby AB
XRAY T1 EVO2.pdf - Minicars Hobby AB
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
5<br />
2. REAR TRANSMISSION<br />
BAG<br />
02<br />
309054<br />
BB 10x15<br />
309045<br />
BB 6x10<br />
309035<br />
BB 5x9<br />
309452<br />
P 2x10<br />
309314<br />
ST 6X12<br />
302040<br />
305511<br />
302040<br />
309452<br />
302070<br />
305511<br />
305582<br />
305570<br />
309314<br />
305540<br />
305431<br />
303015<br />
309054<br />
309045<br />
30 2040 LOWER SUSPENSION HOLDER (SET 2+1+1)<br />
30 2070 ECCENTRIC NYLON HUB FOR BULKHEAD + COVERS (4+2)<br />
30 2053 ALU LOWER SUSPENSION HOLDER<br />
30 3040 ALU REAR BULKHEAD BRACE<br />
30 5001 BALL DIFFERENTIAL - SPRING STEEL - SET (OPTION)<br />
30 5431 HIGH-PERFORMANCE KEVLAR DRIVE BELT FRONT 3 x 507 MM<br />
30 5441 HIGH-PERFORMANCE KEVLAR DRIVE BELT REAR 4 x180 MM<br />
30 5511 LAYSHAFT SPRING STEEL INTEGR. SPUR G. ADAPTER EVO2<br />
30 5540 ONE-WAY ADJUSTMENT NUT M6<br />
30 5570 FIXED PULLEY 16T<br />
30 5582 ONE-WAY PULLEY 16T WITH GROOVED ONE-WAY BEARING<br />
30 9035 HIGH-SPEED BALL-BEARING MR95ZZ 5 x 9 x 3 BLUE COVERED (2)<br />
30 9045 HIGH-SPEED BALL-BEARING MR106ZZ 6 x 10 x 3 BLUE COVERED (2)<br />
305000<br />
305441<br />
The new adjustable bulkheads enable you to easily adjust belt tightness.<br />
1. Press in the plastic holders for the small ball-bearings into the bulkheads as shown.<br />
The plastic holder with the hole through it goes in the right bulkhead; the plastic holder<br />
without the hole through it goes in the left bulkhead.<br />
2. Press #309035 (BB 5x9) ball-bearing into the plastic holder in the right bulkhead. Press<br />
#309045 (BB 6x10) ball-bearing into the plastic holder in the left bulkhead.<br />
3. Press the large eccentric ball-bearing holders into the bulkheads. Align the tab of each<br />
holder with the middle notch in each bulkhead as shown.<br />
4. Press #309054 (BB 10x15) ball-bearings into the eccentric covers.<br />
Make sure the bearings turn freely and easily.<br />
How to adjust the tightness of belt:<br />
To loosen rear belt:<br />
Rotate rear nylon hubs in arrow direction (A)<br />
To tighten rear belt:<br />
Rotate rear nylon hubs in arrow direction (B)<br />
1. Insert the layshaft with spur gear adapter through the preinstalled ball-bearing<br />
in the bulkhead.<br />
2. Install the diff washer thrust shim.<br />
3. Install the 16T one-way pulley. Make sure that the one-way pulley "free wheels"<br />
when rotated forward, but locks onto the layshaft when rotated backward.<br />
4. Install the fixed pulley shim.<br />
5. Press the #309452 (P 2x10) pin into the hole on the layshaft. Note that the pin<br />
should stick out from both sides equally.<br />
A<br />
B<br />
303040<br />
309035<br />
302040<br />
309343<br />
302053<br />
301110<br />
302070<br />
302040<br />
303025<br />
309335<br />
30 9054 HIGH-SPEED BALL-BEARING 10 x 15 x 4 BLUE COVERED (2)<br />
30 9314 CONE WASHER ST 6 x 12 (10)<br />
30 9335 HEX SCREW SH M3x10 (10)<br />
30 9343 HEX SCREW SFH M3x6 (10)<br />
30 9452 PIN 2x10 (10)<br />
30 1110 6-CELL CHASSIS 2.5 MM GRAPHITE - CNC MACHINED<br />
30 3015 ALU SUSP. ADJUST<strong>AB</strong>LE BULKHEAD REAR RIGHT - HARD COATED<br />
30 3025 ALU SUSP. ADJUST<strong>AB</strong>LE BULKHEAD REAR LEFT - HARD COATED<br />
30 5000 BALL DIFFERENTIAL WITH L<strong>AB</strong>YRINTH DUST COVERS - SET<br />
INITIAL POSITION:<br />
PLACE T<strong>AB</strong><br />
IN THIS NOTCH<br />
➊<br />
➎<br />
➊<br />
➋<br />
➋<br />
➌<br />
DETAIL DETAIL<br />
➌<br />
➍<br />
➍<br />
To remove hub, press<br />
out with tool as shown.<br />
➏ ➐ ➑