You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Contents<br />
7.4 Disposing of sanding dust<br />
7.5 Replacing the sanding belt<br />
Caution!<br />
1 Introduction..................................................................................................................................................................... When the dust bag becomes 1/3 full the bag must be emptied. The dust collecting 4<br />
capacity is greatly reduced when the fatal bag is filled Caution! past this Danger point. from The machine sanding starting dust must up!<br />
2 Scope be of delivery disposed ............................................................................................................................................................ of in a fire proof, non-flammable container. When replacing The container the sanding must belt, be there 5 covered is a risk from t<br />
3 with a fire proof, non-flammable lid. Store the container unintentionally. only outdoors. Always disconnect the parquet floor s<br />
Machine specifications COBRA CLASSIC ................................................................................................................... 6<br />
working at the sanding belt.<br />
3.1 Important components ...................................................................................................................................................... 6<br />
3.2 Technical Caution! data .................................................................................................................................................................. Fire risk!<br />
7<br />
3.3 Safety Because and machine of protection the fire facilities............................................................................................................................ risk, the sanding dust contained in the dust bag must always 7 be<br />
4<br />
disposed of immediately if the machine is stopped Caution! for a Risk extended of cutting period your hands! of time.<br />
Proper The use ....................................................................................................................................................................... fatal<br />
sanding dust must be disposed of in a fire The proof, sanding non-flammable grains of the container. sanding 7 belt The have sharp ed<br />
container must be covered with a fire proof, non-flammable when replacing lid. the Store sanding the belt. container only<br />
5 Assembly outdoors. of the machine............................................................................................................................................... 8<br />
5.1 Installing the guide tube ................................................................................................................................................... 8<br />
5.2 Installing the motor ........................................................................................................................................................... 8<br />
Instructions for replacing the sanding belt:<br />
7.5 6 Disassembling Replacing for transport the sanding ......................................................................................................................................... belt<br />
9<br />
6.1 Removing the guide tube ................................................................................................................................................ 9<br />
6.2 Removing the motor.......................................................................................................................................................... 1. Switch the machine off. 10<br />
Caution! Danger from machine starting up! 2. Disconnect the machine from the mains<br />
7 Operating When the COBRA replacing CLASSIC the .................................................................................................................................. sanding belt, there is a risk from power. the machine starting up<br />
fatal<br />
11<br />
unintentionally. Always disconnect the power from 3. Open the motor the sanding before drum working cover (1). on the<br />
7.1 Protective clothing and equipment .................................................................................................................................. 11<br />
7.2 Fitting the sanding dust bag belt. ........................................................................................................................................................<br />
4. Move the tension lever (2) forward.<br />
11<br />
The<br />
7.3 Safety instructions regarding dust ....................................................................................................................................<br />
sanding belt which was held under<br />
12<br />
tension<br />
7.4 Disposing Caution! of sanding Risk dust ............................................................................................................................................... of cutting your hands!<br />
is now released. Pull it out to the 12side.<br />
7.5 Replacing 5. Insert a new sanding belt.<br />
The the sanding belt grains .............................................................................................................................................. of the sanding fatal belt have sharp edges. Always wear safety 13gloves<br />
7.6 Adjusting the sanding pressure ....................................................................................................................................... 6. Clamp the new sanding belt by moving 14 the<br />
when replacing the sanding belt.<br />
7.7 Safety instructions for electric cable and connectors ...................................................................................................... tension lever (2) backward. 14<br />
7.8 Connecting the COBRA CLASSIC to the mains power .................................................................................................. 7. Close the sanding drum cover (1). 15<br />
7.9 Remarks Instructions about sanding parquet for replacing and plank floors the .......................................................................................................... sanding belt:<br />
16<br />
7.10 <strong>Sanding</strong> with the COBRA CLASSIC ............................................................................................................................... 19<br />
1. Switch the machine off.<br />
8 Maintenance ................................................................................................................................................................... 24<br />
2. Disconnect power to the motor.<br />
8.1 Changing the sanding drum ............................................................................................................................................ 24<br />
8.2 Adjusting 3. the Open running the wheels sanding .......................................................................................................................................... drum cover (1).<br />
26<br />
8.3 Adjusting the castor wheels ............................................................................................................................................ 27<br />
8.4 Adjusting 4. the Move tension the roller tension ............................................................................................................................................... lever (2) forward.<br />
28<br />
8.5 Changing the The belt.............................................................................................................................................................. sanding which was held under<br />
29<br />
8.6<br />
8.7<br />
9<br />
10<br />
Checking dust tension extraction is ................................................................................................................................................. now released. Pull it out to the<br />
Switching off side. and storing the machine ............................................................................................................................<br />
Declaration 5. Insert of conformity a new .............................................................................................................................................. sanding belt.<br />
6. Clamp the new sanding belt by moving<br />
Warranty........................................................................................................................................................................... the tension lever (2) backward.<br />
7. Close the sanding drum cover (1).<br />
30<br />
30<br />
31<br />
32<br />
Pallmann <strong>King</strong> <strong>Cobra</strong> <strong>Manual</strong> 13