Seals Specification Guide - Timken

Shaft Diameter Shaft/mm Width Overall Fitted Width Tolerance Height Part
Range* (d1) (d1) Shaft (A) Width (B) Width (B1) (+/-) (C) Number Style Matl
47.84 50.00 1250 0.56 0.98 0.79 0.160 0.59 812500 VS1 S
50.00 51.97 1300 0.56 0.98 0.79 0.160 0.59 813000 VS1 S
50.98 51.77 1300 0.56 0.98 0.79 0.160 0.59 813003 VS4 S
51.97 53.94 1300 0.56 0.98 0.79 0.160 0.59 813500 VS1 S
52.76 53.74 1350 0.56 0.98 0.79 0.160 0.59 813503 VS4 S
53.94 55.91 1400 0.56 0.98 0.79 0.160 0.59 814000 VS1 S
54.72 55.71 1400 0.56 0.98 0.79 0.160 0.59 814003 VS4 S
55.91 57.87 1450 0.56 0.98 0.79 0.160 0.59 814500 VS1 S
56.69 57.68 1450 0.56 0.98 0.79 0.160 0.59 814503 VS4 S
57.87 59.84 1500 0.56 0.98 0.79 0.160 0.59 815000 VS1 S
58.66 59.65 1500 0.56 0.98 0.79 0.160 0.59 815003 VS4 S
59.84 61.81 1550 0.56 0.98 0.79 0.160 0.59 815500 VS1 S
60.63 61.81 1550 0.56 0.98 0.79 0.160 0.59 815503 VS4 S
61.81 63.78 1600 0.56 0.98 0.79 0.160 0.59 816000 VS1 S
62.99 64.57 1600 0.56 0.98 0.79 0.160 0.59 816003 VS4 S
63.78 65.75 1650 0.56 0.98 0.79 0.160 0.59 816500 VS1 S
64.57 66.14 1650 0.56 0.98 0.79 0.160 0.59 816503 VS4 S
65.75 67.72 1700 0.56 0.98 0.79 0.160 0.59 817000 VS1 S
66.15 67.72 1700 0.56 0.98 0.79 0.160 0.59 817003 VS4 S
67.72 69.69 1750 0.56 0.98 0.79 0.160 0.59 817500 VS1 S
67.72 69.49 1750 0.56 0.98 0.79 0.160 0.59 817503 VS4 S
69.46 71.26 1800 0.56 0.98 0.79 0.160 0.59 818003 VS4 S
69.69 71.65 1800 0.56 0.98 0.79 0.160 0.59 818000 VS1 S
71.26 73.03 1850 0.56 0.98 0.79 0.160 0.59 818503 VS4 S
71.65 73.62 1850 0.56 0.98 0.79 0.160 0.59 818500 VS1 S
73.03 75.00 1900 0.56 0.98 0.79 0.160 0.59 819003 VS4 S
73.62 75.59 1900 0.56 0.98 0.79 0.160 0.59 819000 VS1 S
75.00 76.97 1950 0.56 0.98 0.79 0.160 0.59 819503 VS4 S
75.59 77.56 1950 0.56 0.98 0.79 0.160 0.59 819500 VS1 S
76.90 79.10 2000 0.56 0.98 0.79 0.160 0.59 820003 VS4 S
77.56 79.53 1999 0.56 0.98 0.79 0.160 0.59 819990 VS1 S
84 * Select the larger V-Seal when the dimension d1 is on the boundary between two sizes of V-Seals