Ball Bearings Catalog - Timken

D
A
•
Ball BeaRIngs
GVFTD, GVFTDR Relubricatable Series
VFTD, VFTDR Non-Relubricatable Series
GvFTD, GvFTDR RELUBRICATABLE SERIES - vFTD, vFTDR NON-RELUBRICATABLE SERIES
• Malleable iron flange cartridges provide self-alignment
and rigid support for medium-duty applications.
Suggested shaft tolerances: nominal to -.013 mm, -.0005”.
BEARING DATA
Unit Bearing Number Dimensions and Load Ratings
vFTD, vFTDR RA...RRB Page D56
GvFTD, GvFTDR GRA...RRB Page D57
H
J
d1
L
N
HOLE WIDTH SQ.
TOLERANCE ± .005
D118 TIMKEN PRODUCTS CATALOG
E
A
E1
A1
A 3
VFTD VFTDR
H2
MINIMUM
FRAME
OPENING
H
H
J
J
L
L
45°
N
HOLE WIDTH SQ.
TOLERANCE ± .005
GVFTD
37°
N
HOLE WIDTH SQ.
TOLERANCE ± .005
GVFTDR
FOR NON-RELUBRICATABLE SERIES, OMIT G PREFIX ON UNIT AND BEARING NUMBER.
TO ORDER, SPECIFY UNIT AND SHAFT DIAMETER. Example: vFTD 1 3/16’’ or vFTDR 1 3/16’’ or GvFTD 1 3/16’’ OR GvFTDR 1 3/16’’.
Unit Shaft H J L N H2 E A E1 A3 A1 d1 Bearing Collar Unit
face reverse Dia. Number Number Wt.
mounted mounted
RELUBRICATABLE SERIES (1)
mm mm mm mm mm mm mm mm mm mm mm mm kg
in. in. in. in. in. in. in. in. in. in. in. in. lbs.
GVFTD GVFTDR 1 /2 81 63.5 53.2 7.1 47.6 31.8 17.5 22.2 7.9 9.5 28.6 GRA008RRB S1008K 0.245
GVFTD GVFTDR 5 /8 3 3 /16 2 1 /2 2 3 /32 9 /32 1 7 /8 1 1 /4 11 /16 7 /8 5 /16 3 /8 1 1 /8 GRA010RRB S1010K 0.54
GVFTD GVFTDR 17 GRAE17RRB SE17K
GVFTD GVFTDR 3 /4 90.5 71.4 60.3 8.7 54.8 34.1 19.8 23.4 9.1 10.7 33.3 GRA012RRB S1012K 0.331
GVFTD GVFTDR 20 3 9 /16 2 13 /16 2 3 /8 11 /32 2 5 /32 1 11 /32 25 /32 59 /64 23 /64 27 /64 1 5 /16 GRAE20RRB SE20K 0.73
GVFTD GVFTDR 7 /8 GRA014RRB S1014K
GVFTD GVFTDR 15 /16 95.2 76.2 66.7 8.7 60.3 34.1 19.8 23.4 9.1 10.7 38.1 GRA015RRB S1015K 0.363
GVFTD GVFTDR 1 3 3 /4 3 2 5 /8 11 /32 2 3 /8 1 11 /32 25 /32 59 /64 23 /64 27 /64 1 1 /2 GRA100RRB S1100K 0.8
GVFTD GVFTDR 25 GRAE25RRB SE25K
GVFTD GVFTDR 1 1 /8 GRA102RRB S1102K
GVFTD GVFTDR 1 3 /16 112.7 90.5 78.6 10.3 71.4 38.9 22.2 26.6 10.7 11.9 44.5 GRA103RRB S1103K 0.608
GVFTD GVFTDR 1 1 /4 S 4 7 /16 3 9 /16 3 3 /32 13 /32 2 13 /16 1 17 /32 7 /8 1 3 /64 27 /64 15 /32 1 3 /4 GRA103RRB2 S1103K3 1.34
GVFTD GVFTDR 30 GRAE30RRB SE30K
GVFTD GVFTDR 1 1 /4 GRA104RRB S1104K 0.862
GVFTD GVFTDR 1 3 /8 122.2 100 88.9 10.3 81.8 42.1 23.8 29.4 11.1 12.7 54 GRA106RRB S1106K 1.9
GVFTD GVFTDR 1 7 /16 4 13 /16 3 15 /16 3 1 /2 13 /32 3 7 /32 1 21 /32 15 /16 1 5 /32 7 /16 1 /2 2 1 /8 GRA107RRB S1107K
GVFTD GVFTDR 35 GRAE35RRB SE35K
(1) All units have a 1 /4-28 grease fitting.
Shaft diameter with an S = smaller housing.
d1
25°
50°
E1
E
A
A1
A 3
H2
MINIMUM
FRAME
OPENING