You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
EUROPEAN PRICELIST <strong>2018</strong>
AMPLIFIERS<br />
Jeff <strong>Genzler</strong> has done it again. The Magellan amplifiers, build on the legacy of the famous Genz Benz,<br />
but with serious updates and new design. And the line is simple, with only two heads so far, the 350<br />
and the 800. Both great looking and sounding amps, built to last a lifetime. For smaller gigs, the 350<br />
will do the job, and for larger gigs, the 800 takes you all the way. Both amps can work with a 2.67 ohms<br />
load, and will give you a trouble free run for your money.<br />
MAGELLAN 350 AMPHEAD<br />
(SKU: MG-350)<br />
PREAMP: All solid state analog design with integrated soft clip circuitry.<br />
INPUT: :1 Meg ohm input impedance. Mute button.<br />
CHANNEL OVERVIEW: Voiced to provide natural, pristine, transparent<br />
reproduction of the bass instrument. The circuitry consists of<br />
an FET feedback type variable gain circuit that provides wide range,<br />
continuously variable gain for use with a wide range of instrument<br />
pick-ups and preamps.<br />
CONTOUR: Continuously variable control of 2 vastly different response<br />
curves. In either CURVE position, when the SHAPE control is<br />
all the way off (CCW) the response curve is completely FLAT.<br />
Curve A (Blue): A variable pre-shaped curve that boosts lows and highs<br />
while simultaneously cutting mids. The slopes are fairly gentle which<br />
keep the tone shaping very musical. This curve covers a wide range of<br />
sounds from flat to classic to modern depending on the position of the<br />
SHAPE control.<br />
Curve B (Amber): A variable pre-shaped curve with attenuated high<br />
mids and highs, a low mid bump, and a slight roll-off of the lowest bass<br />
frequencies. Again, the slopes are fairly gentle which keep the tone<br />
shaping very musical. This curve is intended to provide sounds in the<br />
range of vintage amps and vintage cabinets that do not have tweeters.<br />
ACTIVE EQUALIZATION: The MAGELLAN® 350 contains an active<br />
3 band equalizer with a sweepable parametric mid-range frequency<br />
control.<br />
Bass:<br />
Mid:<br />
Freq:<br />
+/- 15dB boost/cut shelving curve with a corner frequency of 75Hz<br />
+/- 15dB boost/cut of the variable mid frequency selected<br />
Variable mid frequency from 150Hz-3kHz<br />
Treble: +/- 15dB boost/cut shelving curve with a corner frequency of 6kHz<br />
POWER AMP: The MAGELLAN® 350 uses a state of the art, class D<br />
power amplifier design and a high frequency auto-sensing universal<br />
switch-mode power supply (SMPS) to achieve unprecedented high<br />
performance and lightweight packaging. There are no Voltage Switches<br />
to change or jumpers to move. This SMPS senses the line voltage from<br />
100-240 Volts and automatically configures itself.<br />
REAR PANEL:<br />
XLR Direct Output<br />
Mic / Line Switch<br />
Pre / Post EQ Switch<br />
Ground Lift Switch<br />
Aux Input<br />
Head Phones<br />
Dual Speakon® Speaker Outputs<br />
Impedance Selector Switch for 8, 4 or 2.67 ohm operation<br />
SPECIFICATIONS:<br />
Power Output: 175W/8 Ohms, 350W/4 Ohms and 350W/2.67 Ohms<br />
Minimum Speaker Load: 2.67 Ohms<br />
Operating Power condition: 100 – 240V, 50/60 Hz<br />
Dimensions: 2.63”H X 9”W X 9.83”D (67mm H x 228.6mm W x<br />
249.8mm D)<br />
Weight: 3.5 LBS (1.75 Kg)<br />
<strong>Europe</strong>an distribution: Audiosupport · +45 7734 1214 · info@audiosupport.dk · www.audiosupport.dk
MAGELLAN 800 AMPHEAD<br />
(SKU: MG-800)<br />
PREAMP: All solid state analog design with integrated soft clip circuitry.<br />
INPUT: 1Meg ohm input impedance, with 8,5dB PAD switch. Mute button.<br />
CLEAN CHANNEL OVERVIEW: Voiced to provide natural, pristine,<br />
transparent reproduction of the bass instrument.<br />
DRIVE CHANNEL OVERVIEW: Voiced to provide a more “driven”<br />
tonal signature and harmonic content along with a softer top end and<br />
more relaxed low frequency response.<br />
CONTOUR: Continuously variable control of 2 vastly different response<br />
curves. In either CURVE position, when the SHAPE control is<br />
all the way off (CCW) the response curve is completely FLAT.<br />
Curve A (Blue): a variable pre-shaped curve that boosts lows and highs while<br />
simultaneously cutting mids. The slopes are fairly gentle which keep the tone<br />
shaping very musical. This curve covers a wide range of sounds from flat to<br />
classic to modern depending on the position of the SHAPE control.<br />
Curve B (Amber): a variable pre-shaped curve with attenuated high<br />
mids and highs, a low mid bump, and a slight roll-off of the lowest bass<br />
frequencies. Again, the slopes are fairly gentle which keep the tone<br />
shaping very musical. This curve is intended to provide sounds in the<br />
range of vintage amps and vintage cabinets that do not have tweeters.<br />
ACTIVE EQUALIZATION: The MAGELLAN® 800 contains an active 3<br />
band equalizer with a sweepable parametric mid-range frequency control.<br />
Bass:<br />
Mid:<br />
Freq:<br />
+/- 15dB boost/cut shelving curve with a corner frequency of 75Hz<br />
+/- 15dB boost/cut of the variable mid frequency selected<br />
Variable mid frequency from 150Hz-3kHz<br />
Treble: +/- 15dB boost/cut shelving curve with a corner frequency of 6kHz<br />
POWER AMP: The MAGELLAN® 800 uses a state of the art, class D<br />
power amplifier design and a high frequency auto-sensing universal<br />
switch-mode power supply (SMPS) to achieve unprecedented high<br />
performance and lightweight packaging. There are no Voltage Switches<br />
to change or jumpers to move. This SMPS senses the line voltage from<br />
100-240 Volts and automatically configures itself.<br />
REAR PANEL<br />
XLR Direct Output<br />
Mic / Line Switch<br />
Pre / Post EQ Switch<br />
Ground Lift Switch<br />
Effects Loop<br />
Aux Input<br />
Head Phones<br />
Foot Switch – Channel switching (pedal NOT included)<br />
Dual Speakon® Speaker Outputs<br />
Impedance Selector Switch for 8, 4 or 2.67 ohm operation<br />
SPECIFICATIONS:<br />
Power Output: 400W/8 Ohms, 800W/4 Ohms and 800W/2.67 Ohms<br />
Minimum Speaker Load: 2.67 Ohms<br />
Operating Power condition: 100 – 240V, 50/60 Hz<br />
Dimensions: 3”H X 11,25”W X 10,5”D (76,2mm H x 285.75mm W x<br />
266.7mm D)<br />
Weight: 6.25 LBS (3.8 Kg)
BASS ARRAY CABINETS<br />
With the Bass Array cabinets, Jeff <strong>Genzler</strong> really has made a difference,<br />
when it comes to compact bass cabinets. DO NOT compare<br />
these cabs to any standard 10” or 12” woodbox out there, cause the<br />
this is a very different ballgame.<br />
Size and weight compares to most traditional cabs, but a careful<br />
selection of speakers and crossover, combined with the stacked 3”<br />
mid-high drivers in a ported cabinet, gives you a full range bass<br />
sound, with unique horizontal dispersion. From the low B string to<br />
effortless mids and highs, these cabinets deliver bass sounds, that<br />
are heard and defined all over the stage.<br />
Equipped with two NL-2 Speakon connectors, as well as two ¼”<br />
jacks*.<br />
BASS ARRAY 10-2<br />
SLANTED<br />
(SKU: BA10-2)<br />
One 10” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling. 4 premium Neodymium 2,5” Mid/<br />
High cone drivers, loaded into a sealed Line<br />
Array stack. This cabinet is very well suited<br />
for both electric and upright basses.<br />
Top/rear handle, Large rubber feet. *This cabinet<br />
comes with two Neutrik Combi Speakon/<br />
Jack inputs.<br />
POWER HANDLING: 250 watts RMS<br />
FREQUENCY RESPONSE: 55 Hz - 20 kHz<br />
SENSITIVITY: 96 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY: 1,6kHz<br />
DIMENSIONS: 33 x 39,37 x 38,1 cm<br />
WEIGHT: 9,5 kg<br />
BASS ARRAY 210-3<br />
(SKU: BA210-3)<br />
Two 10” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling.<br />
4 premium Faital Neodymium 3” Mid/High<br />
cone drivers, loaded into a sealed Line Array<br />
stack. Heavy recessed handles, Large rubber<br />
feet.<br />
POWER HANDLING: 500 watts RMS<br />
FREQUENCY RESPONSE: 45 Hz - 15 kHz<br />
SENSITIVITY: 99 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY: 800Hz<br />
DIMENSIONS: 40,64 x 58,42 x 45,72 cm<br />
WEIGHT: 17,23 kg<br />
BASS ARRAY 410-3<br />
(SKU: BA410-3)<br />
Four 10” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling.<br />
6 premium Faital Neodymium 3” Mid/High<br />
cone drivers, loaded into a sealed Line Array<br />
stack. Heavy recessed handles, Large rubber<br />
feet.<br />
POWER HANDLING: 1000 watts RMS<br />
FREQUENCY RESPONSE: 40 Hz - 15 kHz<br />
SENSITIVITY: 103 dB 1W 1M<br />
IMPEDANCE: 4 ohms<br />
CROSSOVER FREQUENCY: 800Hz<br />
DIMENSIONS: 40,64 x 58,42 x 45,72 cm<br />
WEIGHT: 24,95 kg<br />
<strong>Europe</strong>an distribution: Audiosupport · +45 7734 1214 · info@audiosupport.dk · www.audiosupport.dk
BASS ARRAY 12-3<br />
STRAIGHT<br />
(SKU: BA12-3 STR)<br />
One 12” Neodymium cast<br />
frame woofer, with Dual<br />
Wound voice coil, for increased<br />
power handling. 4 premium<br />
Faital Neodymium 3” Mid/<br />
High cone drivers, loaded into<br />
a sealed Line Array stack. Deluxe<br />
heavy strap handles, Large<br />
rubber feet.<br />
POWER HANDLING:<br />
350 watts RMS<br />
FREQUENCY RESPONSE:<br />
32 Hz - 15 kHz<br />
SENSITIVITY: 98 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY:<br />
800Hz<br />
DIMENSIONS:<br />
40,64 x 48,26 x 45,72 cm<br />
WEIGHT: 15,4 kg<br />
BASS ARRAY 12-3<br />
SLANTED<br />
(SKU: BA12-3 SLT)<br />
The 12-3 in a 6-degree slanted<br />
design, for improved self-monitoring,<br />
when playing on stage.<br />
One 12” Neodymium cast<br />
frame woofer, with Dual<br />
Wound voice coil, for increased<br />
power handling. 4 premium<br />
Faital Neodymium 3” Mid/<br />
High cone drivers, loaded into<br />
a sealed Line Array stack. Top<br />
mounted handle, Large rubber<br />
feet.<br />
POWER HANDLING: 350<br />
watts RMS<br />
FREQUENCY RESPONSE:<br />
32 Hz - 15 kHz<br />
SENSITIVITY: 98 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY:<br />
800Hz<br />
DIMENSIONS:<br />
40,64 x 48,26 x 45,72 cm<br />
WEIGHT: 14,5 kg
MAGELLAN CABINETS<br />
The Magellan Series, is a serious choice, when searching for a fat<br />
and grounded tone. Focused midrange and great projection cuts<br />
right through any mix. Built from Baltic Birch, and equipped with<br />
Custom made Faital woofers, plus crossover and 1” Bullet Tweeter.<br />
The distinctive front triangular ports provide an optimum porting<br />
design as well as structural strength in the corners of the cabinet.<br />
Beautifully finished in Heavy Duty textured Black Vinyl, with<br />
matching Silver/Black grille, and silver metallic piping. The result<br />
is a cool range of cabinets for the Pro player. All cabinets equipped<br />
with One Neutrik Speakon and two 1/4” inputs, large rubber feet<br />
and heavy duty strap handles.<br />
Padded covers available for all models<br />
MAGELLAN 1X12 CABINET<br />
W/TWEETER<br />
(SKU: MG-112T)<br />
One 12” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling. 1” Bullet tweeter with Ferro Fluid<br />
infusion in the coil gap, for higher power<br />
rating and HF response, Deluxe strap handle,<br />
Large rubber feet.<br />
MAGELLAN 2X12 CABINET<br />
W/TWEETER<br />
(SKU: MG-212T)<br />
Two 12” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling. 1” Bullet tweeter with Ferro Fluid<br />
infusion in the coil gap, for higher power<br />
rating and HF response, Deluxe strap handle,<br />
Large rubber feet.<br />
POWER HANDLING: 350 watts RMS<br />
FREQUENCY RESPONSE: 36 Hz - 14 kHz<br />
SENSITIVITY: 97 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY: 4,7Khz<br />
DIMENSIONS: 40,64 x 48,26 x 40,64 cm<br />
WEIGHT: 13,6 kg<br />
POWER HANDLING: 700 watts RMS<br />
FREQUENCY RESPONSE: 33 Hz - 14 kHz<br />
SENSITIVITY: 100 dB 1W 1M<br />
IMPEDANCE: 4 ohms<br />
CROSSOVER FREQUENCY: 4,7Khz<br />
DIMENSIONS: 78,75 x 48,26 x 40,64 cm<br />
WEIGHT: 24,5 kg<br />
MAGELLAN COMBO<br />
MAGELLAN 350 COMBO<br />
(SKU: MG350-BA10-COMBO)<br />
The Magellan Combo offers you a prepacked setup,<br />
consisting of a MG350 amp, a BA10-2 cabinet as well as<br />
Speakon cable, and a Cradle for mounting the amp on<br />
top of the cabinet.<br />
This little combo gives you all you need for smaller<br />
gigs, as well as for your upright bass, and you can even<br />
buy an optional carrybag, that holds the complete<br />
package for easy transportation.<br />
<strong>Europe</strong>an distribution: Audiosupport · +45 7734 1214 · info@audiosupport.dk · www.audiosupport.dk
ACOUSTIC INSTRUMENT<br />
AMPLIFICATION<br />
ACOUSTIC ARRAY<br />
PRO AMPLIFIER<br />
(SKU: AA-PRO)<br />
The Acoustic Array Pro sets a new standard<br />
for amplifying acoustic instruments.<br />
Portable, powerful and packed with features,<br />
the AA Pro gives you the perfect amplification<br />
for any stringed instrument, and you<br />
can even use it for vocals too. Add an extra<br />
cabinet, and you have a powerful little PA rig.<br />
The <strong>Genzler</strong> trademark is the Acoustic Array<br />
configuration, which you will, of course, also<br />
find on both the AA Pro and the optional<br />
extension speaker.<br />
AA Pro has two identical preamps, with both<br />
XLR and ¼” jack inputs, plus a long list of<br />
features:<br />
• Phantom Power for Condenser Mics<br />
• Signal Phase Reverse Switch<br />
• Unique Contour Circuit for Quick<br />
Tonal Adjustments<br />
• Active EQ w/Sweepable Mids<br />
• Adjustable Digital Reverb and Chorus<br />
on Each Channel (switchable)<br />
• Innovative Acoustic Array Speaker<br />
System Design<br />
• 10” Woofer w/4 x 2.5” Cone-driver Line<br />
Array<br />
• Slanted Cabinet Design for Improved<br />
Projection<br />
• Ultra-lightweight 12,25 Kg Compact<br />
Cabinet Design<br />
• Power Output: 150 W (combo); 300 W<br />
with Extension Cab<br />
• 3 XLR Direct Outputs (Channel A,<br />
Channel B or both)<br />
• Effects Loop<br />
• Auxiliary Input<br />
• Bottom-mounted Stand Adaptor<br />
• Dimensions: 49.53 x 44.45 x 55.88 cm<br />
EXTENSION SPEAKER<br />
FOR THE AA PRO<br />
(SKU: AA-PRO-EXT)<br />
One 10” Neodymium cast frame woofer, with<br />
Dual Wound voice coil, for increased power<br />
handling. 4 premium Neodymium 2,5” Mid/<br />
High cone drivers, loaded into a sealed Line<br />
Array stack. This cabinet is very well suited for<br />
both electric and upright basses.<br />
Top/rear handle, Large rubber feet. *This cabinet<br />
comes with two Neutrik Combi Speakon/<br />
Jack inputs.<br />
POWER HANDLING: 250 watts RMS<br />
FREQUENCY RESPONSE: 55 Hz - 20 kHz<br />
SENSITIVITY: 96 dB 1W 1M<br />
IMPEDANCE: 8 ohms<br />
CROSSOVER FREQUENCY: 1,6kHz<br />
DIMENSIONS: 33 x 39,37 x 38,1 cm<br />
WEIGHT: 9,5 kg
ACCESSORIES<br />
CVR-BA12-3 STR<br />
Heavy-Duty, Padded Cover for BA12-3 STR.<br />
CVR-BA12-3 SLT<br />
Heavy-Duty, Padded Cover for BA12-3 SLT.<br />
CVR-BA210-3<br />
Heavy-Duty, Padded Cover for BA210-3<br />
Cabinet.<br />
MG-800-BAG<br />
Heavy-Duty, Padded Carry Bag for MG-800<br />
Amplifier.<br />
CVR-AA-PRO<br />
Heavy-Duty Padded Cover for the AA.<br />
MG-350-COMBO-BAG<br />
Heavy-Duty, Padded, Carry Bag for MG-350<br />
Combo.<br />
MG-350-CRADLE<br />
Mounting Bracket for MG-350, w/Speakon®<br />
Cable.<br />
<strong>Europe</strong>an distribution: Audiosupport · +45 7734 1214 · info@audiosupport.dk · www.audiosupport.dk
<strong>2018</strong> EUROPEAN SUGGESTED RETAIL<br />
BASS ARRAY® BASS CABINETS<br />
Model<br />
Description<br />
BA10-2 Bass Array Neo 1x10” w/4 x 2.5” stack, 250W, 8 ohm 659 4.925 6.570 6.750<br />
BA12-3 STR BA STRAIGHT VERSION 12”w/4x3”Array,350W,8ohm 999 7.445 9.930 10.199<br />
BA12-3 SLT BA SLANT VERSION 12”w/4X3”Array,350W,8ohm 999 7.445 9.930 10.199<br />
BA210-3 Bass Array-Neo 2x10” w/4 x 3” stack, 500W, 8 ohm 1.179 8.785 11.720 12.035<br />
BA410-3 Bass Array-Neo 4x10” w/6 x 3” stack, 1000W, 4 ohm 1.699 12.675 16.900 17.365<br />
MAGELLAN®SERIES BASS CABINETS<br />
Model<br />
Description<br />
MG-112T Magellan – Neo 1x12” w/tweeter, 350W, 8 ohm 749 5.580 7.440 7.645<br />
MG-212T Magellan – Neo 2x12” w/tweeter, 700W, 4 ohm 1.229 9.150 12.200 12.535<br />
MAGELLAN®SERIES AMPLIFIERS<br />
Model<br />
Description<br />
MG350 Single Chan Pre, 175W/8ohm,350W/4ohm/2.67ohm 499 3.725 4.970 5.100<br />
MG800 Two Chan Pre, 400W/8ohm, 800W/4ohm/2.67ohm 899 6.699 8.935 9.175<br />
MG350-BA10-COMBO “Kit” w/MG-350 Amp, BA10-2 Cab, MG-350-Cradle 1.159 8.635 11.515 11.825<br />
ACCESSORIES<br />
Model<br />
Description<br />
CVR-BA12-3 STR Heavy-Duty, Padded Cover for BA12-3 STR 70 525 700 720<br />
CVR-BA12-3 SLT Heavy-Duty, Padded Cover for BA12-3 SLT 70 525 700 720<br />
CVR-BA210-3 Heavy-Duty, Padded Cover for BA210-3 Cabinet 72 540 720 740<br />
MG-800-BAG Heavy-Duty, Padded Carry Bag for MG-800 Amplifier 66 499 665 685<br />
MG-350-CRADLE Mounting Bracket for MG-350, w/Speakon® Cable 68 510 680 699<br />
MG-350-COMBO-BAG Heavy-Duty, Padded, Carry Bag for MG-350 Combo 110 820 1.099 1.125<br />
ACOUSTIC INSTRUMENT AMPLIFICATION<br />
Model<br />
Description<br />
AA-PRO Acoustic Array PRO Acoustic Guitar Amplifier 1.149 8.560 11.415 11.725<br />
CVR-AA-PRO Heavy-Duty Padded Cover for the AA-PRO 69 515 690 705<br />
AA-PRO-EXT Extension Cabinet For Acoustic Array PRO 649 4.835 6.450 6.625
“I started my first amplifier company with a vision, and a passion, in a garage<br />
in Phoenix, Arizona decades ago. As professional musician for more than a<br />
dozen years, I saw a need for smart, reliable, amplification systems that made<br />
strategic advancements to the form.<br />
My wife Catherine and I, along with our dedicated team, built that company<br />
and delivered exceptional products and support, worked closely with inspiring<br />
and talented people, and earned a global reputation for innovative designs<br />
and superior quality.<br />
Now we’re returning to our roots.<br />
I’m building smart, pure, innovative bass amps and cabinets. We’re proud to<br />
have our longtime engineer, Scott Andres, as an important part of our team.<br />
We have strong relationships with trusted craftspeople, suppliers, and retailers<br />
around the world.<br />
We now live in Brooklyn, close to family and an incredible music vibe. As a<br />
company, we do the work because we love it, because the music is worth it,<br />
because the conversation with our customers is inspiring. Our spirit is simple<br />
and true, uncompromising and dedicated.<br />
I’m proud to present the next generation of GENZLER amplification.<br />
This is the product you expect from the people you trust.”<br />
- Jeff <strong>Genzler</strong><br />
ABOUT GENZLER<br />
<strong>Europe</strong>an distribution: Audiosupport · +45 7734 1214 · info@audiosupport.dk · www.audiosupport.dk