holeshot® drills

CUTTING TOOLS
MANCHESTER
lower cost per cut
www.manchestertools.com
Holeshot ®
OTM
®
OTM

G2
GRADES
WCMX Insert Grades
Grade Description Application
6N Uncoated Cermet10 Non-Ferrous Materials, Stainless, Cast Iron
10 Uncoated C2 Carbide Gray Cast Iron, Non-Ferrous Materials
UD11 Uncoated C2 Carbide Non-Ferrous Materials, High Temp Alloys
90C CVD TiN/TiCN Coated C6 Carbide Steel, Stainless
66C PVD TiN Coated C5 Carbide Very Tough General Purpose Grade
CD42 CVD TiN/TiC Coated C1 Carbide Stainless, Alloy Steel
PD51 PVD TiAlN Coated C2 Carbide Steel, Stainless, High Temp Alloys
WCGT Insert Grades
Grade Description Application
12 Uncoated C3 Carbide, J-Polish First Choice for Aluminum, Brass, etc.
TCMT Insert Grades
Grade Description Application
5N Uncoated Cermet Non-Ferrous Materials, Stainless, Cast Iron
13 Uncoated C2 Carbide Non-Ferrous Materials, High Temp Alloys
23C CVD TiN/TiC/TiN Coated C5 Carbide Steel, Stainless, Steel Castings
40C CVD TiN/Al2O3/TiCN Coated C5 Carbide Stainless, Alloy Steel
XPMT Insert Grades
Grade Description Application
1 Cermet Stainless,Tool Steel, High Temp Alloys
5 Cermet Steel,Tool Steel, High Temp Alloys
6 Cermet Steel,Tool Steel, High Temp Alloys
10 Uncoated C2 Carbide Gray Cast Iron, Non-Ferrous, Nickel Alloys
13 Uncoated C2 Carbide Heat Resistant and Titanium Alloys, Non-Ferrous
23C CVD TiN/TiC/TiN Coated C5 Carbide Steel, Stainless, Steel Castings
66C PVD TiN Coated C5 Carbide Stainless, Tool Steel, Tough Materials
93C PVD TiCN Coated C6 Carbide Tough Stainless, High Temp and Titanium Alloys
APET Insert Grades
Grade Description Application
12 Uncoated C3 Carbide w/ J-Polish Aluminum, Brass, Plastic
35C CVD TiN/Al2O3/TiC/TiN Coated C6 Carbide Steel, Stainless, Steel Castings
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-0515-X3N 0.515 0.750 1.54 4.23 2.20 2.03 0.070
DR-0531-X3N 0.531 0.750 1.59 4.29 2.26 2.03 0.072
DR-0551-X3N 0.551 (14 mm) 0.750 1.65 4.43 2.40 2.03 0.074
DR-0563-X3N 0.563 0.750 1.70 4.36 2.33 2.03 0.079
DR-0591-X3N
DR-0594-X3N
0.591 (15 mm)
0.594
0.750
0.750
1.77
1.78
4.55
4.49
2.52
2.46
2.03
2.03
0.083
0.083
WCMX S30204-M1A 2 SCR-07 T6
DR-0625-X3N 0.625 0.750 1.87 4.62 2.59 2.03 0.087
DR-0630-X3N 0.630 (16 mm) 0.750 1.89 4.68 2.65 2.03 0.088
DR-0656-X3N 0.656 0.750 1.96 4.75 2.72 2.03 0.091
DR-0669-X3N 0.669 (17 mm) 0.750 2.01 4.80 2.77 2.03 0.093
DR-0688-X3N 0.688 0.750 2.06 4.87 2.84 2.03 0.090
DR-0709-X3N 0.709 (18 mm) 0.750 2.13 5.04 3.01 2.03 0.092
DR-0719-X3N 0.719 0.750 2.15 5.00 2.97 2.03 0.093
DR-0750-X3N 0.750 0.750 2.25 5.13 3.10 2.03 0.102
DR-0781-X3N 0.781 0.750 2.34 5.26 3.23 2.03 0.106 WCMX 040204-M1A 2 SCR-01 T7
DR-0787-X3N 0.787 (20 mm) 0.750 2.36 5.29 3.26 2.03 0.106
DR-0813-X3N 0.813 0.750 2.44 5.39 3.36 2.03 0.110
DR-0827-X3N 0.827 (21 mm) 0.750 2.48 5.41 3.38 2.03 0.112
DR-0844-X3N 0.844 0.750 2.53 5.52 3.49 2.03 0.114
DR-0866-X3N 0.866 (22 mm) 1.000 2.60 5.80 3.52 2.28 0.130
DR-0875 0.875 1.000 1.75 4.78 2.50 2.28 0.131
DR-0875-X3N 0.875 1.000 2.63 5.79 3.51 2.28 0.131
DR-0906 0.906 (23 mm) 1.000 1.75 4.78 2.50 2.28 0.135 WCMX 050308-M1(A)
DR-0906-X3N
DR-0937
0.906 (23 mm)
0.937
1.000
1.000
2.71
1.75
5.88
4.78
3.60
2.50
2.28
2.28
0.135
0.139
or
WCGT 050308-M1
2 SCR-03 T9
DR-0937-X3N 0.937 1.000 2.81 5.98 3.70 2.28 0.139
DR-0945 0.945 (24 mm) 1.000 1.75 4.78 2.50 2.28 0.140
DR-0945-X3N 0.945 1.000 2.83 6.04 3.76 2.28 0.140
DR-0969 0.969 1.000 1.75 4.78 2.50 2.28 0.143
DR-0969-X3N 0.969 1.000 2.91 6.08 3.80 2.28 0.143
DR-0984 0.984 (25 mm) 1.000 1.75 4.78 2.50 2.28 0.145
DR-0984-X3N 0.984 (25 mm) 1.000 2.95 6.17 3.89 2.28 0.145
DR-1000 1.000 1.000 1.75 4.78 2.50 2.28 0.147 WCMX 050308-M1(A)
DR-1000-X3N
DR-1024
1.000
1.024 (26 mm)
1.000
1.000
3.00
1.75
6.18
4.78
3.90
2.50
2.28
2.28
0.147
0.150
or
WCGT 050308-M1
2 SCR-03 T9
DR-1024-X3N 1.024 (26 mm) 1.000 3.07 6.29 4.01 2.28 0.150
DR-1031 1.031 1.000 2.13 5.16 2.88 2.28 0.151
DR-1031-X3N 1.031 1.000 3.09 6.27 3.99 2.28 0.151
DR-1062 1.062 (27 mm) 1.000 2.13 5.16 2.88 2.28 0.155
See page G11 for Insert Specifications and Grade Selection.
G3

G4
HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-1062-X3N 1.062 (27 mm) 1.000 3.18 6.37 4.09 2.28 0.155
DR-1094 1.094 1.000 2.13 5.16 2.88 2.28 0.159
DR-1094-X3N 1.094 1.000 3.28 6.47 4.19 2.28 0.159
DR-1102 1.102 (28 mm) 1.000 2.13 5.16 2.88 2.28 0.160
DR-1102-X3N 1.102 (28 mm) 1.000 3.31 6.53 4.25 2.28 0.160 WCMX 050308-M1(A)
DR-1125 1.125 1.000 2.13 5.16 2.88 2.28 0.163 or 2 SCR-03 T9
DR-1125-X3N 1.125 1.000 3.37 6.56 4.28 2.28 0.163 WCGT 050308-M1
DR-1142 1.142 (29 mm) 1.000 2.13 5.16 2.88 2.28 0.165
DR-1142-X3N 1.142 (29 mm) 1.000 3.43 6.66 4.38 2.28 0.165
DR-1156 1.156 1.000 2.13 5.16 2.88 2.28 0.167
DR-1156-X3N 1.156 1.000 3.47 6.67 4.39 2.28 0.167
DR-1181 1.181 (30 mm) 1.000 2.13 5.16 2.88 2.28 0.169
DR-1181-X3N 1.181 (30 mm) 1.250 3.54 6.78 4.50 2.28 0.169
DR-1187 1.187 1.000 2.13 5.16 2.88 2.28 0.169
DR-1187-X3N 1.187 1.250 3.56 6.76 4.48 2.28 0.169 WCMX 06T308-M1(A)
DR-1219
DR-1219-X3N
1.219
1.219
1.000
1.250
2.50
3.66
5.53
6.86
3.25
4.58
2.28
2.28
0.173
0.173
or
WCGT 06T308-M1
2 SCR-30 T10
DR-1250 1.250 1.000 2.50 5.53 3.25 2.28 0.177
DR-1250-X3N 1.250 1.250 3.75 6.96 4.68 2.28 0.177
DR-1260 1.260 (32 mm) 1.000 2.50 5.53 3.25 2.28 0.179
DR-1260-X3N 1.260 (32 mm) 1.250 3.78 7.03 4.75 2.28 0.179
DR-1281 1.281 1.000 2.50 5.53 3.25 2.28 0.181
DR-1281-X3N 1.281 1.250 3.84 7.05 4.77 2.28 0.181
DR-1299 1.299 (33 mm) 1.000 2.50 5.53 3.25 2.28 0.184
DR-1299-X3N 1.299 (33 mm) 1.250 3.90 7.15 4.87 2.28 0.184
DR-1312 1.312 1.000 2.50 5.53 3.25 2.28 0.185 WCMX 06T308-M1(A)
DR-1312-X3N 1.312 1.250 3.94 7.16 4.88 2.28 0.185 or 2 SCR-30 T10
DR-1339 1.339 (34 mm) 1.000 2.50 5.53 3.25 2.28 0.189 WCGT 06T308-M1
DR-1339-X3N 1.339 (34 mm) 1.250 4.02 7.27 4.99 2.28 0.189
DR-1344 1.344 1.000 2.50 5.53 3.25 2.28 0.190
DR-1344-X3N 1.344 1.250 4.03 7.25 4.97 2.28 0.190
DR-1375 1.375 1.000 2.50 5.53 3.25 2.28 0.193
DR-1375-X3N 1.375 1.250 4.12 7.34 5.06 2.28 0.193
DR-1406 1.406 1.000 2.75 5.78 3.50 2.28 0.197
DR-1406-X3N 1.406 1.250 4.22 7.45 5.17 2.28 0.197
DR-1417 1.417 (36 mm) 1.000 2.75 5.78 3.50 2.28 0.199
DR-1417-X3N 1.417 (36 mm) 1.250 4.25 7.52 5.24 2.28 0.199 WCMX 06T308-M1(A)
DR-1437 1.437 1.000 2.75 5.78 3.50 2.28 0.196 or 2 SCR-30 T10
DR-1437-X3N 1.437 1.250 4.31 7.54 5.26 2.28 0.196 WCGT 06T308-M1
DR-1457 1.457 (37 mm) 1.000 2.75 5.78 3.50 2.28 0.199
DR-1457-X3N 1.457 (37 mm) 1.250 4.37 7.64 5.36 2.28 0.199
DR-1469 1.469 1.000 2.75 5.78 3.50 2.28 0.200
DR-1469-X3N 1.469 1.250 4.40 7.63 5.35 2.28 0.200
See page G11 for Insert Specifications and Grade Selection.

HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-1496 1.496 (38 mm) 1.000 2.75 5.78 3.50 2.28 0.204
DR-1496-X3N 1.496 (38 mm) 1.250 4.49 7.76 5.48 2.28 0.204
DR-1500 1.500 1.000 2.75 5.78 3.50 2.28 0.204
DR-1500-X3N 1.500 1.250 4.50 7.73 5.45 2.28 0.204 WCMX 06T308-M1(A)
DR-1531 1.531 1.250 2.88 6.16 3.88 2.28 0.208 or
DR-1531-X3N 1.531 1.250 4.59 8.08 5.80 2.28 0.208 WCGT 06T308-M1
DR-1535 1.535 (39 mm) 1.250 2.88 6.16 3.88 2.28 0.209
DR-1535-X3N 1.535 (39 mm) 1.250 4.61 8.08 5.80 2.28 0.209
DR-1562 1.562 1.250 2.88 6.16 3.88 2.28 0.212
DR-1562-X3N 1.562 1.250 4.68 8.17 5.89 2.28 0.212
DR-1575 1.575 (40 mm) 1.250 2.88 6.16 3.88 2.28 0.208
DR-1575-X3N 1.575 (40 mm) 1.500 4.72 8.61 5.92 2.69 0.208
DR-1594 1.594 1.250 2.88 6.16 3.88 2.28 0.210
DR-1594-X3N 1.594 1.500 4.78 8.68 5.99 2.69 0.210 WCMX 050308-M1(A)
DR-1614 1.614 (41 mm) 1.250 2.88 6.16 3.88 2.28 0.212 or
DR-1614-X3N 1.614 (41 mm) 1.500 4.84 8.73 6.04 2.69 0.212 WCGT 050308-M1
DR-1625 1.625 1.250 2.88 6.16 3.88 2.28 0.214
DR-1625-X3N 1.625 1.500 4.87 8.77 6.08 2.69 0.214
DR-1656 1.656 1.250 2.88 6.16 3.88 2.28 0.218
DR-1656-X3N 1.656 1.500 4.96 8.87 6.18 2.69 0.218
DR-1687 1.687 1.250 2.88 6.16 3.88 2.28 0.221
DR-1687-X3N 1.687 1.500 5.06 8.97 6.28 2.69 0.221
DR-1693 1.693 (43 mm) 1.250 2.88 6.16 3.88 2.28 0.222
DR-1693-X3N 1.693 (43 mm) 1.500 5.08 8.97 6.28 2.69 0.222 WCMX 050308-M1(A)
DR-1719 1.719 1.250 3.00 6.41 4.13 2.28 0.225 or
DR-1719-X3N 1.719 1.500 5.15 9.20 6.51 2.69 0.225 WCGT 050308-M1
DR-1732 1.732 (44 mm) 1.250 3.00 6.41 4.13 2.28 0.224
DR-1732-X3N 1.732 (44 mm) 1.500 5.20 9.29 6.60 2.69 0.224
DR-1750 1.750 1.250 3.00 6.41 4.13 2.28 0.225
DR-1750-X3N 1.750 1.500 5.25 9.30 6.61 2.69 0.225
DR-1772 1.772 (45 mm) 1.250 3.00 6.41 4.13 2.28 0.231
DR-1772-X3N 1.772 (45 mm) 1.500 5.31 9.42 6.73 2.69 0.231
DR-1781 1.781 1.250 3.00 6.41 4.13 2.28 0.223
DR-1781-X3N 1.781 1.500 5.34 9.38 6.69 2.69 0.223 WCMX 050308-M1(A)
DR-1812 1.812 1.250 3.00 6.41 4.13 2.28 0.230 or
DR-1812-X3N 1.812 1.500 5.43 9.48 6.79 2.69 0.230 WCGT 050308-M1
DR-1844 1.844 1.250 3.38 6.78 4.50 2.28 0.233
DR-1844-X3N 1.844 1.500 5.53 9.58 6.89 2.69 0.233
DR-1850 1.850 (47 mm) 1.250 3.38 6.78 4.50 2.28 0.233
DR-1850-X3N 1.850 (47 mm) 1.500 5.55 9.66 6.97 2.69 0.233
See page G11 for Insert Specifications and Grade Selection.
2 SCR-30 T10
3 SCR-03 T9
3 SCR-03 T9
4 SCR-03 T9
4 SCR-03 T9
G5

G6
HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-1875 1.875 1.250 3.38 6.78 4.50 2.28 0.240
DR-1875-X3N 1.875 1.500 5.62 9.68 6.99 2.69 0.240
DR-1890 1.890 (48 mm) 1.250 3.38 6.78 4.50 2.28 0.245
DR-1890-X3N 1.890 (48 mm) 1.500 5.67 9.79 7.10 2.69 0.245 WCMX 050308-M1(A)
DR-1906 1.906 1.250 3.38 6.78 4.50 2.28 0.254 or
DR-1906-X3N 1.906 1.500 5.72 9.79 7.10 2.69 0.254 WCGT 050308-M1
DR-1929 1.929 (49 mm) 1.250 3.38 6.78 4.50 2.28 0.259
DR-1929-X3N 1.929 (49 mm) 1.500 5.79 9.92 7.23 2.69 0.259
DR-1937 1.937 1.250 3.38 6.78 4.50 2.28 0.259
DR-1937-X3N 1.937 1.500 5.81 9.89 7.20 2.69 0.259
DR-1969 1.969 (50 MM) 1.250 3.38 6.78 4.50 2.28 0.260
DR-1969-X3N 1.969 (50 MM) 1.500 5.91 9.99 7.30 2.69 0.260
DR-2000-X1 2.000 1.250 2.13 6.06 3.38 2.28 0.267
DR-2000 2.000 1.250 3.38 6.78 4.50 2.28 0.267 WCMX 050308-M1(A)
DR-2000-X3N 2.000 1.500 6.00 10.09 7.40 2.69 0.267 or
DR-2008 2.008 (51 mm) 1.250 3.38 6.78 4.50 2.28 0.267 WCGT 050308-M1
DR-2008-X3N 2.008 (51 mm) 1.500 6.02 10.16 7.47 2.69 0.267
DR-2031-X1 2.031 1.500 2.13 6.06 3.38 2.69 0.268
DR-2031 2.031 1.500 3.50 7.44 4.75 2.69 0.268
DR-2031-X3N 2.031 1.500 6.09 10.30 7.61 2.69 0.268
DR-2047 2.047 (52 mm) 1.500 3.50 7.44 4.75 2.69 0.259
DR-2047-X3N 2.047 (52 mm) 2.000 6.14 10.91 7.66 3.25 0.259
DR-2062-X1 2.062 1.500 2.13 6.06 3.38 2.69 0.260
DR-2062 2.062 1.500 3.50 7.44 4.75 2.69 0.260 WCMX 06T308-M1(A)
DR-2062-X3N 2.062 2.000 6.18 10.94 7.69 3.25 0.260 or
DR-2087 2.087 (53 mm) 1.500 3.50 7.44 4.75 2.69 0.267 WCGT 06T308-M1
DR-2087-X3N 2.087 (53 mm) 2.000 6.26 11.04 7.79 3.25 0.267
DR-2094-X1 2.094 1.500 2.13 6.06 3.38 2.69 0.267
DR-2094 2.094 1.500 3.50 7.44 4.75 2.69 0.267
DR-2094-X3N 2.094 2.000 6.28 11.05 7.80 3.25 0.267
DR-2125-X1 2.125 (54 MM) 1.500 2.13 6.06 3.38 2.69 0.266
DR-2125 2.125 (54 MM) 1.500 3.50 7.44 4.75 2.69 0.266
DR-2125-X3N 2.125 2.000 6.37 11.14 7.89 3.25 0.266
DR-2156-X1 2.156 1.500 2.31 6.25 3.56 2.69 0.270 WCMX 06T308-M1(A)
DR-2156 2.156 1.500 3.88 7.81 5.13 2.69 0.270 or
DR-2156-X3N 2.156 2.000 6.47 11.24 7.99 3.25 0.270 WCGT 06T308-M1
DR-2165 2.165 (55 mm) 1.500 3.88 7.81 5.13 2.69 0.273
DR-2165-X3N 2.165 (55 mm) 2.000 6.50 11.28 8.03 3.25 0.273
DR-2187-X1 2.187 1.500 2.31 6.25 3.56 2.69 0.273
DR-2187 2.187 1.500 3.88 7.81 5.13 2.69 0.273
See page G11 for Insert Specifications and Grade Selection.
4 SCR-03 T9
4 SCR-03 T9
4 SCR-30 T10
4 SCR-30 T10

HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-2187-X3N 2.187 2.000 6.56 11.33 8.08 3.25 0.273
DR-2205 2.205 (56 mm) 1.500 3.88 7.81 5.13 2.69 0.283
DR-2205-X3N 2.205 (56 mm) 2.000 6.61 11.41 8.16 3.25 0.283
DR-2219-X1 2.219 1.500 2.31 6.25 3.56 2.69 0.277 WCMX 06T308-M1(A)
DR-2219 2.219 1.500 3.88 7.81 5.13 2.69 0.277 or
DR-2219-X3N 2.219 2.000 6.66 11.44 8.19 3.25 0.277 WCGT 06T308-M1
DR-2244 2.244 (57 mm) 1.500 3.88 7.81 5.13 2.69 0.281
DR-2244-X3N 2.244 (57 mm) 2.000 6.73 11.52 8.27 3.25 0.281
DR-2250-X1 2.250 1.500 2.31 6.25 3.56 2.69 0.281
DR-2250 2.250 1.500 3.88 7.81 5.13 2.69 0.281
DR-2250-X3N 2.250 2.000 6.75 11.53 8.28 3.25 0.281
DR2281-X1 2.281 1.500 2.31 6.25 3.56 2.69 0.283
DR-2281 2.281 1.500 3.88 7.81 5.13 2.69 0.283
DR-2281-X3N 2.281 2.000 6.84 11.62 8.37 3.25 0.283 WCMX 06T308-M1(A)
DR-2312-X1 2.312 1.500 2.31 6.25 3.56 2.69 0.287 or
DR-2312 2.312 1.500 3.88 7.81 5.13 2.69 0.287 WCGT 06T308-M1
DR-2312-X3N 2.312 2.000 6.93 11.72 8.47 3.25 0.287
DR-2323 2.323 (59 mm) 1.500 3.88 7.81 5.13 2.69 0.290
DR-2323-X3N 2.323 (59 mm) 2.000 6.97 11.77 8.52 3.25 0.290
DR-2344-X1 2.344 1.500 2.50 6.56 3.88 2.69 0.289
DR-2344 2.344 1.500 4.13 8.19 5.50 2.69 0.289
DR-2344-X3N 2.344 2.000 7.03 11.95 8.70 3.25 0.289
DR-2362 2.362 (60 mm) 1.500 4.13 8.19 5.50 2.69 0.301
DR-2362-X3N 2.362 (60 mm) 2.000 7.09 12.02 8.77 3.25 0.301 WCMX 06T308-M1(A)
DR-2375-X1 2.375 1.500 2.50 6.56 3.88 2.69 0.298 or
DR-2375 2.375 1.500 4.13 8.19 5.50 2.69 0.298 WCGT 06T308-M1
DR-2375-X3N 2.375 2.000 7.12 12.05 8.80 3.25 0.298
DR-2402 2.402 (61 mm) 1.500 4.13 8.19 5.50 2.69 0.304
DR-2402-X3N 2.402 (61 mm) 2.000 7.20 12.14 8.89 3.25 0.304
DR-2406-X1 2.406 1.500 2.50 6.56 3.88 2.69 0.304
DR-2406 2.406 1.500 4.13 8.19 5.50 2.69 0.304
DR-2406-X3N 2.406 2.000 7.22 12.15 8.90 3.25 0.304
DR-2437-X1 2.437 1.500 2.50 6.56 3.88 2.69 0.309
DR-2437 2.437 1.500 4.13 8.19 5.50 2.69 0.309 WCMX 06T308-M1(A)
DR-2437-X3N 2.437 2.000 7.31 12.25 9.00 3.25 0.309 or
DR-2441 2.441 (62 mm) 1.500 4.13 8.19 5.50 2.69 0.309 WCGT 06T308-M1
DR-2441-X3N 2.441 (62 mm) 2.000 7.32 12.26 9.01 3.25 0.309
DR-2469-X1 2.469 1.500 2.50 6.56 3.88 2.69 0.319
DR-2469 2.469 1.500 4.13 8.19 5.50 2.69 0.319
DR-2469-X3N 2.469 2.000 7.41 12.36 9.11 3.25 0.319
See page G11 for Insert Specifications and Grade Selection.
4 SCR-30 T10
4 SCR-30 T10
4 SCR-30 T10
4 SCR-30 T10
G7

G8
HOLESHOT ® DRILLS
Holeshot ® Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 L4 Insert Qty. Screw Wrench
DR-2480 2.480 (63 mm) 1.500 4.13 8.19 5.50 2.69 0.310
DR-2480-X3N 2.480 (63 mm) 2.000 7.44 12.38 9.13 3.25 0.310
DR-2500-X1 2.500 1.500 2.50 6.56 3.88 2.69 0.329
DR-2500 2.500 1.500 4.13 8.19 5.50 2.69 0.329
DR-2500-X3N 2.500 2.000 7.50 12.46 9.21 3.25 0.329 WCMX 06T308-M1(A)
DR-2625-X1 2.625 2.000 2.75 7.50 4.25 3.25 0.326 or 4 SCR-30 T10
DR-2625 2.625 2.000 6.50 11.25 8.00 3.25 0.326 WCGT 06T308-M1
DR-2750-X1 2.750 2.000 2.75 7.50 4.25 3.25 0.340
DR-2750 2.750 2.000 6.50 11.25 8.00 3.25 0.340
DR-2875-X1 2.875 2.000 3.00 7.75 4.50 3.25 0.357
DR-2875 2.875 2.000 6.50 11.25 8.00 3.25 0.357
DR-3000-X1 3.000 2.000 3.00 7.75 4.50 3.25 0.369
DR-3000 3.000 2.000 6.50 11.25 8.00 3.25 0.369
DR-3125-X1 3.125 2.000 3.25 8.13 4.88 3.25 0.393
DR-3125 3.125 2.000 7.63 12.50 9.25 3.25 0.393 WCMX 06T308-M1(A)
DR-3250-X1 3.250 2.000 3.25 8.13 4.88 3.25 0.387 or 6 SCR-30 T10
DR-3250 3.250 2.000 7.63 12.50 9.25 3.25 0.387 WCGT 06T308-M1
DR-3375-X1 3.375 2.000 3.50 8.38 5.13 3.25 0.393
DR-3375 3.375 2.000 7.63 12.50 9.25 3.25 0.393
DR-3500-X1 3.500 2.000 3.50 8.38 5.13 3.25 0.440
DR-3500 3.500 2.000 7.63 12.50 9.25 3.25 0.440
DR-3625-X1 3.625 2.000 3.75 8.75 5.50 3.25 0.441
DR-3625 3.625 2.000 7.94 12.67 9.42 3.25 0.441
DR-3750-X1 3.750 2.000 3.75 8.75 5.50 3.25 0.459 WCMX 06T308-M1(A)
DR-3750 3.750 2.000 8.00 13.00 9.75 3.25 0.459 or 6 SCR-30 T10
DR-3875-X1 3.875 2.000 4.00 9.38 6.13 3.25 0.470 WCGT 06T308-M1
DR-3875 3.875 2.000 8.44 13.44 10.19 3.25 0.470
DR-4000-X1 4.000 2.000 4.00 9.38 6.13 3.25 0.482
DR-4000 4.000 2.000 8.56 13.88 10.63 3.25 0.482
See page G11 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

COREMASTER COREDRILLS
Fixed Pocket
COREMASTER COREDRILLS
Adjustable Cartridge
Coremaster Coredrills – Fixed Pocket INCH
Part Number D d d2 MDD L1 L2 L3 Insert (2) Screw Wrench
CD-0825 .825 1.000 N/A 1.750 4.750 2.250 2.500 SCR-03 T9
CD-0865 .865 1.000 N/A 1.750 4.750 2.250 2.500 WCMX 050308-M1(A) SCR-03 T9
CD-0938 .938 1.000 N/A 1.750 4.750 2.250 2.500 or SCR-03 T9
CD-0990 .990 1.000 N/A 2.000 5.000 2.500 2.500 WCGT 050308-M1 SCR-03 T9
CD-1052 1.052 1.000 N/A 2.000 5.000 2.500 2.500 SCR-03 T9
CD-1115
CD-1178
CD-1240
CD-1303
1.115
1.178
1.240
1.303
1.000
1.000
1.000
1.000
N/A
N/A
N/A
N/A
2.500
2.500
2.500
2.500
5.500
5.500
5.500
5.500
3.000
3.000
3.000
3.000
2.500
2.500
2.500
2.500
WCMX 050308-M1(A)
or
WCGT 050308-M1
SCR-30
SCR-30
SCR-30
SCR-30
T10
T10
T10
T10
*Maximum material removal: WCMX 050308 – 5/16” per side, WCMX 06T308 – 3/8” per side.
See page G11 for Insert Specifications and Grade Selection.
Coremaster Coredrills – Adjustable Cartridge INCH
Part Number D d d2 MDD L1 L2 L3 Insert (2) Screw Wrench Cartridge
Cartridge
Screw
CD-1360-C 1.36-1.46 1.250 N/A 2.750 6.250 3.500 2.750 SCR-30 T10 02-03 01-01
CD-1460-C 1.46-1.56 1.250 N/A 2.750 6.250 3.500 2.750 SCR-30 T10 02-03 01-01
CD-1560-C 1.56-1.66 1.250 N/A 2.750 6.250 3.500 2.750 SCR-30 T10 02-03 01-01
CD-1660-C 1.66-1.76 1.250 N/A 2.750 6.250 3.500 2.750 SCR-30 T10 02-03 01-02
CD-1760-C 1.76-1.86 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-1860-C 1.86-1.96 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-1960-C 1.96-2.06 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2060-C 2.06-2.16 1.500 N/A 3.125 7.000 4.000 3.000 WCMX 06T308-M1(A) SCR-30 T10 02-03 01-02
CD-2160-C 2.16-2.26 1.500 N/A 3.125 7.000 4.000 3.000 or SCR-30 T10 02-03 01-02
CD-2260-C 2.26-2.36 1.500 N/A 3.125 7.000 4.000 3.000 WCGT 06T308-M1 SCR-30 T10 02-03 01-02
CD-2360-C 2.36-2.46 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2460-C 2.46-2.56 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2560-C 2.56-2.66 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2660-C 2.66-2.76 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2760-C 2.76-2.86 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2860-C 2.86-2.96 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
CD-2960-C 2.96-3.06 1.500 N/A 3.125 7.000 4.000 3.000 SCR-30 T10 02-03 01-02
*Maximum material removal: WCMX 050308 – 5/16” per side, WCMX 06T308 – 3/8” per side.
Cartridges can be adjusted 0.075” per side, providing 0.150” adjustment capability on diameter.
See page G11 for Insert Specifications and Grade Selection.
G9

G10
COREMASTER COREDRILLS XL
Fixed Pocket
COREMASTER COREDRILLS XL
Adjustable Cartridge
Coremaster Coredrills XL – Fixed Pocket INCH
Part Number D d d2 MDD L1 L2 L3 Insert (2) Screw Wrench
CD-0825-XL 0.825 1.000 1.375 2.250 5.530 3.250 2.280 SCR-03 T9
CD-0865-XL 0.865 1.000 1.375 2.250 5.530 3.250 2.280 WCMX 050308-M1(A) SCR-03 T9
CD-0938-XL 0.938 1.000 1.375 2.500 5.780 3.500 2.280 or SCR-03 T9
CD-0990-XL 0.990 1.000 1.375 2.500 5.780 3.500 2.280 WCGT 050308-M1 SCR-03 T9
CD-1052-XL 1.052 1.000 1.375 2.500 5.780 3.500 2.280 SCR-03 T9
CD-1115-XL
CD-1178-XL
CD-1240-XL
CD-1303-XL
1.115
1.178
1.240
1.303
1.000
1.000
1.000
1.000
1.375
1.375
1.375
1.375
3.000
3.000
3.000
3.000
6.280
6.280
6.280
6.280
4.000
4.000
4.000
4.000
2.280
2.280
2.280
2.280
WCMX 050308-M1(A)
or
WCGT 050308-M1
SCR-30
SCR-30
SCR-30
SCR-30
T10
T10
T10
T10
*Maximum material removal: WCMX 050308 – 5/16” per side, WCMX 06T308 – 3/8” per side.
See page G11 for Insert Specifications and Grade Selection.
Coremaster Coredrills XL – Adjustable Cartridge INCH
Part Number D d d2 MDD L1 L2 L3 Insert (2) Screw Wrench Cartridge
Cartridge
Screw
CD-1350-LC 1.35-1.50 1.250 1.63 3.500 6.780 4.500 2.280 SCR-30 T10 02-03 01-01
CD-1500-LC 1.50-1.65 1.250 1.63 3.500 6.780 4.500 2.280 SCR-30 T10 02-03 01-01
CD-1650-LC 1.65-1.80 1.500 1.88 4.500 8.190 5.500 2.690 SCR-30 T10 02-03 01-02
CD-1800-LC 1.80-1.95 1.500 1.88 4.500 8.190 5.500 2.690 SCR-30 T10 02-03 01-02
CD-1950-LC
CD-2100-LC
1.95-2.10
2.10-2.25
1.500
1.500
N/A
N/A
4.500
4.500
8.190
8.190
5.500
5.500
2.690
2.690
SCR-30 T10 02-03 01-02
WCMX 06T308-M1(A) CD-2250-LC
CD-2400-LC
2.25-2.40
2.40-2.55
2.000
2.000
2.38
N/A
5.500
5.500
9.750
9.750
6.500
6.500
3.250
3.250
or
WCGT 06T308-M1
SCR-30
SCR-30
SCR-30
T10
T10
T10
02-03
02-03
02-03
01-02
01-02
01-02
CD-2550-LC 2.55-2.70 2.000 N/A 5.500 9.750 6.500 3.250 SCR-30 T10 02-03 01-02
CD-2700-LC 2.70-2.85 2.000 N/A 6.000 10.250 7.000 3.250 SCR-30 T10 02-03 01-02
CD-2850-LC 2.85-3.00 2.000 N/A 6.000 10.250 7.000 3.250 SCR-30 T10 02-03 01-02
CD-3000-LC 3.00-3.15 2.000 N/A 6.000 10.250 7.000 3.250 SCR-30 T10 02-03 01-02
*Maximum material removal: WCMX 050308 – 5/16” per side, WCMX 06T308 – 3/8” per side.
Cartridges can be adjusted 0.075” per side, providing 0.150” adjustment capability on diameter.
See page G11 for Insert Specifications and Grade Selection.

WCMX INSERTS
WCGT INSERTS
WCMX Inserts INCH
Grades Available
Cermet Uncoated Coated
Insert Number I.C. T R 6N 10 12 UD11 90C 66C CD42 PD51
WCMX S30204-M1A* 3/16 0.094 0.016
WCMX 040204-M1A* 1/4 0.094 0.016
WCMX 050308-M1 5/16 0.125 0.031
WCMX Inserts are available in the Grades listed above.
WCMX 050308-M1A* 5/16 0.125 0.031
See page G2 for complete grade descriptions.
WCMX 06T308-M1 3/8 0.156 0.031
WCMX 06T308-M1A* 3/8 0.156 0.031
WCMX Inserts are used in Holeshot ® and Coremaster Drills shown on pages G3-G10.
*M1A suffix denotes Aggressive Chipbreaker.
WCGT Inserts INCH
Grades Available
Cermet Uncoated Coated
Insert Number I.C. T R 6N 10 12 UD11 90C 66C CD42 PD51
WCGT 050308-M1 5/16 0.125 0.031
WCGT Inserts are available in the Grades listed above.
WCGT 06T308-M1 3/8 0.156 0.031
See page G2 for complete grade descriptions.
WCGT Inserts are used in Holeshot ® and Coremaster Drills shown on pages G3-G10.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G11

G12
STINGER DRILLS
Stinger Drills INCH / METRIC
Part Number D d MDD L1 L2 L3 Insert Qty. Screw Wrench
SDR-0484 0.484
SDR-0492 (0.492) 12.5 mm
SDR-0500 0.500
SDR-0512 (0.512) 13 mm
SDR-0516 0.516 0.500 1.45 3.45 1.95 1.50 TCMT 1.2(1.2)2 2 SCR-07 T6
SDR-0531 0.531
SDR-0547 0.547
SDR-0551 (0.551) 14 mm
SDR-0563 0.563
SDR-0578 0.578
SDR-0591 (0.591) 15 mm
SDR-0594
SDR-0609
0.594
0.609
0.500 1.63 3.63 2.13 1.50 TCMT 1.2(1.2)2 2 SCR-07 T6
SDR-0625 0.625
SDR-0630 (0.630) 16 mm
SDR-0641 0.641
SDR-0656
SDR-0669
0.656
(0.669) 17 mm
0.500 1.80 3.80 2.30 1.50 TCMT 1.2(1.2)2 2 SCR-07 T6
SDR-0672 0.672
SDR-0688 0.688
SDR-0703 0.703 0.500 1.97 3.97 2.47 1.50 TCMT 1.2(1.2)2 2 SCR-07 T6
SDR-0709 (0.709) 18 mm
SDR-0719 0.719
SDR-0734
SDR-0748
0.734
(0.748) 19 mm
0.625 2.16 4.41 2.66 1.75 TCMT 1.8(1.5)2 2 SCR-05 T7
SDR-0750 0.750
SDR-0766 0.766
SDR-0781 0.781 0.625 2.25 4.63 2.75 1.75 TCMT 1.8(1.5)2 2 SCR-05 T7
SDR-0787 (0.787) 20 mm
SDR-0797
SDR-0813
0.797
0.813
0.750 2.50 5.03 3.00 2.03 TCMT 1.8(1.5)2 2 SCR-05 T7
SDR-0828
SDR-0844
0.828
0.844
0.750 2.66 5.19 3.16 2.03 TCMT 1.8(1.5)2 2 SCR-05 T7
See page G15 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

COUNTERBORES
One Flute Two Flutes
Counterbores INCH
Part Number SHCS Size Cut Diameter Flutes Insert Screw Head
1/4-SHCS-CB 1/4” 0.422 1
5/16-SHCS-CB 5/16” 0.515 1
3/8-SHCS-CB 3/8” 0.609 1
7/16-SHCS-CB 7/16” 0.703 1 TCMT 1.8(1.5)1 SCR-05 T7
1/2-SHCS-CB 1/2” 0.797 2
5/8-SHCS-CB 5/8” 1.000 2
3/4-SHCS-CB 3/4” 1.187 2
Counterbores METRIC
Part Number SHCS Size Cut Diameter Flutes Insert Screw Head
M6-SHCS-CB M6 0.440 1
M8-SHCS-CB M8 0.558 1
M10-SHCS-CB M10 0.676 1 TCMT 1.8(1.5)1 SCR-05 T7
M12-SHCS-CB M12 0.755 2
M16-SHCS-CB M16 1.000 2
NOTE: Maximum material removal per side is 1/4”.
See page G15 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G13

G14
COUNTERSINKS
CS-82-177 CS-82-362 CS-82-612
Countersinks INCH
Part Number FHCS size(s) Min Dia Max Dia Shank Eff Flutes Insert Qty Screw Head
CS-82-177 #10, 1/4, 5/16 0.177 0.673 1/2” 1 TCMT 2(1.5) 1 SCR-01 T7
CS-82-362 3/8, 7/16, 1/2 0.362 1.073 3/4” 1 TCMT 3(2.5) 1 SCR-02 T15
CS-82-612 5/8, 3/4 0.612 1.464 3/4” 1 TCMT 3(2.5) 2 SCR-02 T15
See page G15 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

TCMT INSERTS
TCMT Inserts INCH
Cermet
Grades Available
Uncoated Coated
Part Number I.C. T R 5N 13 23C 40C
TCMT 1.2(1.2)1 5/32 0.078 0.016
TCMT 1.2(1.2)2 5/32 0.078 0.031
TCMT 1.8(1.5)1 7/32 0.094 0.016
TCMT 1.8(1.5)2 7/32 0.094 0.031
TCMT Inserts are available in the Grades listed above.
TCMT 2(1.5)1 1/4 0.094 0.016
See page G2 for complete grade descriptions.
TCMT 2(1.5)2 1/4 0.094 0.031
TCMT 3(2.5)1 3/8 0.156 0.016
TCMT 3(2.5)2 3/8 0.156 0.031
TCMT Inserts are used in Stinger Drills, Counterbores and Countersinks shown on pages G12-G14.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G15

G16
END MILLS
Small Diameter End Mills
Small Diameter End Mills – Single Flute INCH
Part Number D d L1 L2 L3 L4 Insert (1-required) Screw Head
EM 0437-09* 7/16 1/2 2.78 1 1.78 0.37 SCR-04 T7
EM 0500-09* 1/2 1/2 2.78 1 1.78 0.37 XPMT 0902 SCR-04 T7
EM 0562-09** 9/16 1/2 2.78 1 1.78 0.37 SCR-04 T7
*Capable of ramping at 3˚ max.
**Capable of ramping at 8˚ max.
See page G21 for Insert Specifications and Grade Selection.
Small Diameter End Mills – Two Flute INCH
Part Number D d L1 L2 L3 L4 Insert (2-required) Screw Head
EM 0625-09* 5/8 5/8 2.90 1 1.90 0.37 SCR-04 T7
EM 0688-09*
EM 0750-09*
11/16
3/4
5/8
3/4
2.90
3.03
1
1
1.90
2.03
0.37
0.37
XPMT 0902
SCR-04
SCR-04
T7
T7
EM 0875-09* 7/8 3/4 3.03 1 2.03 0.37 SCR-01 T7
*Capable of ramping at 8˚ max.
See page G21 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

END MILLS
Large Diameter End Mills
Large Diameter End Mills – Single Flute INCH
Part Number D d L1 L2 L3 L4 Insert (1-required) Screw Head
EM 0625†* 5/8 3/4 2.90 1 1.90 0.60 SCR-16 T10
EM 0688* 11/16 3/4 2.90 1 1.90 0.60 SCR-16 T10
EM 0750* 3/4 3/4 3.40 1.50 1.90 0.60 XPMT 15T3 SCR-16 T10
EM 0813** 13/16 3/4 3.40 1.50 1.90 0.60 SCR-16 T10
EM 0875** 7/8 3/4 3.40 1.50 1.90 0.60 SCR-16 T10
† The EM 0625 is designed for light cuts only because it has a large insert in a small diameter mill. This tool is non-returnable.
* Capable of ramping at 3˚ max.
** Capable of ramping at 8˚ max.
See page G21 for Insert Specifications and Grade Selection.
Large Diameter End Mills – Two Flute and Three Flute INCH
Part Number D d L1 L2 L3 L4 Flutes Insert (2-3 required) Screw Head
EM 0938* 15/16 3/4 3.40 1.50 1.90 0.60 2 XPMT 15T3 SCR-16 T10
EM 1000-09-3F* 1 3/4 3.03 1 2.03 0.37 3 XPMT 0902 SCR-01 T7
EM 1000* 1 3/4 3.40 1.50 1.90 0.60 2 SCR-16 T10
EM 1000-1005* 1 1 3.78 1.50 2.28 0.60 2 SCR-16 T10
EM 1125* 1-1/8 3/4 3.40 1.50 1.90 0.60 2 SCR-30 T10
EM 1250*
EM 1250-3F*
1-1/4
1-1/4
3/4
1
3.40
3.78
1.50
1.50
1.90
2.28
0.60
0.60
2
3
XPMT 15T3
SCR-30
SCR-30
T10
T10
EM 1375* 1-3/8 3/4 3.40 1.50 1.90 0.60 2 SCR-30 T10
EM 1500* 1-1/2 3/4 3.40 1.50 1.90 0.60 2 SCR-30 T10
EM 1500-3F* 1-1/2 1 3.78 1.50 2.28 0.60 3 SCR-30 T10
* Capable of ramping at 8˚ max.
See page G21 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G17

G18
END MILLS
Extended Length End Mills
END MILLS
Long Edge End Mills
Extended Length End Mills INCH
Part Number D d L1 L2 L3 L4 Flutes Insert (2 required) Screw Head
EM 1000-2.5* 1 3/4 4.40 2.50 1.90 0.60 2 SCR-16 T10
EM 1000-3.5* 1 1 5.78 3.50 2.28 0.60 2 XPMT 15T3 SCR-16 T10
EM 1250-2.5* 1-1/4 1 4.78 2.50 2.28 0.60 2 SCR-30 T10
* Capable of ramping at 8˚ max.
See page G21 for Insert Specifications and Grade Selection.
Long Edge End Mills INCH
Part No. D d L1 L2 L3 L4 Inserts Flutes Insert Screw Head
EM 1250-1500-LE 1-1/4 1 4.41 2.13 2.28 1.50 6 2 XPMT 15T308 SCR-16 T10
EM 1500-2000-LE 1-1/2 1-1/4 4.91 2.63 2.28 2.00 8 2 XPMT 15T3 SCR-30 T10
EM 2000-2775-LE 2 1-1/2 6.25 3.50 2.75 2.77 10 2 (Bottom row) SCR-30 T10
See page G21 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

CHAMFER MILLS
Chamfer Mills INCH
Part Number Lead Root d Width Depth L1 L2 Insert (2) Screw Wrench
CM-0563-15-09 15-deg 0.563 0.500 0.089 0.340 2.78 1.00
CM-0563-20-09 20-deg 0.563 0.500 0.116 0.330 2.78 1.00
CM-0563-25-09 25-deg 0.563 0.500 0.143 0.310 2.78 1.00 SCR-04 T7
CM-0563-30-09
CM-0563-35-09
30-deg
35-deg
0.563
0.563
0.625
0.625
0.169
0.194
0.300
0.280
2.91
2.91
1.00
1.00
XPMT 0902
CM-0563-45-09 45-deg 0.563 0.625 0.239 0.240 2.91 1.00
CM-0563-60-09 60-deg 0.563 0.625 0.301 0.160 2.91 1.00 SCR-01 T7
CM-0563-75-09 75-deg 0.563 0.625 0.327 0.080 2.91 1.00
CM-1000-03 3-deg 1.000 0.750 0.031 0.589 3.15 1.25
CM-1000-05
CM-1000-10
5-deg
10-deg
1.000
1.000
0.750
0.750
0.052
0.103
0.586
0.577
3.15
3.15
1.25
1.25
SCR-16 T10
CM-1000-15
CM-1000-20
15-deg
20-deg
1.000
1.000
0.750
0.750
0.154
0.204
0.564
0.547
3.15
3.15
1.25
1.25
XPMT 15T3
CM-1000-25
CM-1000-30
25-deg
30-deg
1.000
1.000
0.750
0.750
0.252
0.298
0.526
0.501
3.15
3.15
1.25
1.25
SCR-30 T10
CM-1000-35 35-deg 1.000 0.750 0.343 0.472 3.15 1.25
CM-1000-37.5 37.5-deg 1.000 0.750 0.372 0.456 3.15 1.25
CM-1000-41 41-deg 1.000 0.750 0.393 0.433 3.15 1.25
CM-1000-45 45-deg 1.000 0.750 0.400 0.400 3.15 1.25
CM-1000-50
CM-1000-55
50-deg
55-deg
1.000
1.000
0.750
0.750
0.454
0.507
0.376
0.327
3.15
3.15
1.25
1.25
XPMT 15T3 SCR-30 T10
CM-1000-60 60-deg 1.000 0.750 0.521 0.284 3.15 1.25
CM-1000-70 70-deg 1.000 0.750 0.547 0.193 3.15 1.25
CM-1000-75 75-deg 1.000 0.750 0.584 0.146 3.15 1.25
See page G21 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G19

G20
FACE MILLS
Integral Shank
FACE MILLS
Fixed Pocket
Integral Shank Face Mills INCH
Part Number Lead Angle D d Flutes Inserts Screw Head
FM 1500-6 RH 6-deg 1-1/2 3/4 2 XPMT 15T3 SCR-30 T10
See page G21 for Insert Specifications and Grade Selection.
This tool allows for the use of the opposite, often unused, corner of the insert.
3” Diameter, 30° Lead Angle 3” Diameter, 0° Lead Angle
Fixed Pocket Face Mills INCH
Part Number D Lead Angle L2 L4 d K’way # Flutes Inserts Screw Head
FM 2000-30
RH/LH 2 30-deg 1-11/32 0.50 1 3/8 3 SCR-30 T10
FM 2000-90
RH
2 0-deg 1-13/32 0.60 3/4 5/16 3 SCR-30 T10
FM 3000-30
RH/LH 3 30-deg 1-23/32 0.50 1 3/8 4
XPMT 15T3
SCR-30 T10
FM 3000-90
RH
3 0-deg 1-25/32 0.60 1 3/8 4 SCR-30 T10
See page G21 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

XPMT INSERTS
XPMT Inserts INCH
Cermet
Grades Available
Uncoated Coated
Part Number I.C. L W T R 1 5 6 10 13 23C 66C 93C
XPMT 090204 1/4 0.375 0.248 0.094 0.016
XPMT 090208 1/4 0.375 0.248 0.094 0.031
XPMT 090216 1/4 0.375 0.248 0.094 0.063
XPMT 090224 1/4 0.375 0.248 0.094 0.094
XPMT 090231 1/4 0.375 0.248 0.094 0.122
XPMT 15T304 3/8 0.590 0.374 0.156 0.016 XPMT Inserts are available in the Grades listed above.
XPMT 15T308 3/8 0.590 0.374 0.156 0.031
See page G2 for complete grade descriptions.
XPMT 15T316 3/8 0.590 0.374 0.156 0.063
XPMT 15T324 3/8 0.590 0.374 0.156 0.094
XPMT 15T331 3/8 0.590 0.374 0.156 0.122
XPMT 15T348 3/8 0.590 0.374 0.156 0.187
XPMT 15T364 3/8 0.590 0.374 0.156 0.250
XPMT Inserts are used in End Mills (Small and Large Diameter and Extended Length and Long Edge), Chamfer Mills and Face
Mills shown on pages G16-G20.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G21

G22
ALUMINUM CUTTING END MILLS
Aluminum Cutting
ALUMINUM CUTTING END MILLS
Extended Length Aluminum Cutting
Aluminum Cutting End Mills INCH
Part Number D d L1 L2 L4 L5 Flutes Insert Screw Head
EM-0750-AL*
EM-0875-AL*
3/4
7/8
3/4
3/4
3.360
3.360
2.351
2.351
0.300
0.300
1.350
1.350
2
2
APET 0803 SCR-01 T7
EM-1000-AL* 1 3/4 3.380 2.365 0.640 1.360 2
EM-1250-AL*
EM-1500-AL*
1-1/4
1-1/2
3/4
1
3.380
4.000
2.365
2.864
0.640
0.640
1.360
1.740
2
2
APET 1604 SCR-02 T15
EM-2000-AL* 2 1 4.250 3.110 0.640 1.990 3
* Capable of ramping at 8˚ max.
See page G25 for Insert Specifications and Grade Selection.
Extended Length Aluminum Cutting End Mills INCH
Part Number D d L1 L2 L4 L5 Flutes Insert Screw Head
EM-1000-2.75-AL* 1 3/4 4.780 3.780 0.640 2.750 2
EM-1000-3.75-AL* 1 1 6.015 4.875 0.640 3.750 2 APET 1604 SCR-02 T15
EM-1250-2.125-AL* 1-1/4 1 4.433 3.293 0.640 2.125 2
* Capable of ramping at 8˚ max.
See page G25 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

ALUMINUM CUTTING CHAMFER MILLS
Aluminum Cutting Chamfer Mills INCH
Part Number Lead Angle D d L2 L4 Width Insert (2 req’d) Screw Head
CM-1000-15-AL 15-deg 1.000 3/4 1.350 0.613 0.158
CM-1000-20-AL 20-deg 1.000 3/4 1.350 0.595 0.208
CM-1000-30-AL
CM-0800-45-AL
30-deg
45-deg
1.000
0.800
3/4
3/4
1.350
1.350
0.544
0.440
0.304
0.430
APET 1604 SCR-02 T15
CM-0800-60-AL 60-deg 0.800 3/4 1.350 0.308 0.528
CM-0690-75-AL 75-deg 0.690 3/4 1.350 0.158 0.591
See page G25 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G23

G24
ALUMINUM CUTTING FACE MILLS
Fixed Pocket
Aluminum Cutting Face Mills – Fixed Pocket INCH
Part Number Cut Dia. Lead Angle L1 L4 D Keyway # Flutes Inserts Screw Head
FM-AL-2500-90-3 2-1/2" 0-deg 1.570" 0.640" 3/4" 3/8" 3
FM-3000-90-AL 3" 0-deg 1.570" 0.640" 1" 3/8" 6
FM-4000-90-AL
FM-4000-90-AL-125
4"
4"
0-deg
0-deg
1.570"
1.570"
0.640" 1"
0.640" 1-1/4"
3/8"
1/2"
8
8
APET 1604 SCR-02 T15
FM-AL-4000-90-5 4" 0-deg 1.570" 0.640" 1" 3/8" 5
FM-5000-90-AL 5" 0-deg 1.570" 0.640" 1-1/4" 1/2" 8
See page G25 for Insert Specifications and Grade Selection.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969

APET INSERTS
APET Inserts INCH
Grades Available
Uncoated Coated
Part Number I.C. L W T R 12 35C
APET 0803PDFR
APET 1604PDFR
1/4
3/8
0.300
0.630
0.250
0.375
0.125
0.188
0.028
0.039
APET Inserts are available in
the Grades listed above.
APET 160416 3/8 0.630 0.375 0.188 0.060 See page G2 for complete
APET 160431 3/8 0.630 0.375 0.188 0.125
grade descriptions.
APET Inserts are used in Aluminum Cutting End Mills, Aluminum Cutting Chamfer Mills and Aluminum Cutting Face Mills
shown on pages G22-G24.
Customer Service: 800.497.1892 ◆ Technical Support: 800.497.1892 ◆ Fax: 419.738.5969 G25