Maximum Yield Canada July/August 2017

More documents

Recommendations

Info

nutrient solution strength salts that conduct electricity when dissolved in a solution, and this conductive property allows growers to accurately measure the strength of a nutrient solution. The higher the conductivity, the higher the concentration of dissolved salts present in a solution. Electrical conductivity (EC) or total dissolved solid (TDS) meters are the two most commonly used pieces of equipment to measure the concentration of nutrients in a solution. However, TDS meters (commonly referred to as parts per million [ppm] meters) are really EC meters in disguise. TDS meters measure the EC of a nutrient solution then use a conversion factor of 500, 640, or 700 to estimate the ppm of a solution (depending on the brand of the meter). Whether you are using an EC or TDS meter, the steps used to measure your nutrient solution are the same. You will first measure the water that you will be mixing your nutrients with to see if your source water contributes to the overall conductivity of the solution. You will then mix your nutrients into the solution and measure the overall conductivity of water and nutrients combined (if you had any charge in your source water, you will need to subtract that value from the reading if you are trying to achieve a desired EC or ppm). Depending on your irrigation methods (hand watering, drip, ebb and flood, etc.) and irrigation frequency, the strength of your solution will need to be adjusted to maintain the optimal level in the root zone for the crop you’re growing. While it is very important to know the strength of the nutrient solution applied to your crop, it is equally (if not more) important to monitor the amount of soluble salts in your root zone. A simple method used to measure the conductivity of your media is called the pour-thru method. The first step of this method is to irrigate your crop with your nutrient solution until the media is completely saturated. Wait 30 minutes, then place a saucer below the container and pour distilled water over the surface of the media until you collect a sample large enough (about 50 millilitres) to be able to submerge the tip of an EC or TDS probe. This reading will indicate whether you need to increase or reduce your nutrient solution concentration, or if you need to flush the root zone with pure water to remove soluble salts. ENVIRONMENTAL VARIABLES Several environmental variables will impact how fast water and mineral nutrients are taken up by a plant, including but not limited to light intensity, temperature, and relative humidity. As light intensity (µmol/m 2 /s) is increased, the rate of growth also increases and results in a greater demand for nutrients. However, increased light intensity also increases the rate of transpiration, which will cause you to irrigate your crop more frequently. If you are feeding a high rate of fertilizer at each irrigation, this can cause soluble salts to build up in the root zone, resulting in increased osmotic pressure that will make it difficult to for your plants to uptake water and nutrients. Any time you have increased osmotic pressure in the root zone, your growth rate will decrease and yield will be sacrificed. Increasing the air temperature or reducing the relative humidity in your controlled environment will also increase transpiration rates, which will influence your irrigation frequency. The bottom line is this: anytime you are changing environmental variables, it is extremely important to monitor the EC of your root zone to ensure you do not run into issues. 44 grow cycle
WHILE IT IS very important to know the strength of the nutrient solution applied to your crop, it is equally (if not more) important to monitor the amount of soluble salts in your root zone.” There are hundreds of different fertilizer brands on the market, and whichever one you decide to use, make sure it provides balanced levels of macro- and micronutrients necessary for the crop you are growing. EC and TDS meters are great tools used to check the strength of your nutrient solution, however, if you want to know the composition of specific nutrient salts that are contributing to your solution or media, you will need to have a chemical lab analysis done. Different fertilizer salts contribute to the overall EC differently, and certain nutrient components like urea will not contribute to the overall EC until its converted into nitrate (NO 3). Plant nutrition is just one important variable to consider when making adjustments to optimize your controlled environment. To learn more about optimizing environmental conditions, download the Fluence Bioengineering High PPFD Cultivation Guide at fluence.science. grow cycle 45
Page 1: MODERN GROWING CANADIAN EDITION EC
Page 7 and 8: CONTENTS first feed 8 from the edit
Page 10: first feed contributors KEVIN FREND
Page 14: tapped in ask the experts Q I have
Page 18: max facts Feeding the North with Ve
Page 22: good to grow Par Pro Hyper Arc Par
Page 25 and 26: Ideal Air Pro Dual Series Air Condi
Page 28 and 29: feature hydroponic fruit trees BY S
Page 30: feature hydro apps TOP FIVE HYDROPO
Page 33 and 34: get social. facebook | twitter | pi
Page 36 and 37: plant analysis The plant analysis l
Page 38 and 39: plant analysis “WHILE HYDROPONICS
Page 40 and 41: grow cycle grow tent growing “ SU
Page 42: grow cycle nutrient solution streng
Page 47 and 48: THE BEESWAX Beeswax doesn’t get a
Page 49 and 50: “MEASURING LST IS like taking a p
Page 52 and 53: leaf surface temperature Yellow Man
Page 54: leaf surface temperature OPTIMIZING
Page 57 and 58: The company’s products are unique
Page 59 and 60: I ended up growing for the restaura
Page 61 and 62: EXPERIENCE THE FUTURE OF GROWING SA
Page 63 and 64: groundbreakers 63
Page 65 and 66: distributors ----------------------

Maximum Yield Canada July/August 2017

Create successful ePaper yourself

Delete template?

Save as template?