KERBL Horse and Rider 2020

Frost Protection Heating with thermostat
• keeps your water line frost-free to -45 ° C • integrated frost protection thermostat (switch-on temperature
approx. +5 °C, switch-off temperature approx. +13 °C) • not suitable for heating pipes • do not insulate
the thermostat when adding insulation • Protect the area animals could chew on with a bite protector
• VDE tested heating cable • 230 V • IPX7
Frost Protection Accessories
​
Do not mount in animal feed area unprotected - use only
24-volt heating cable. Do not shorten the heating cable!
frost-protected down to max. -45 °C
Pipe
Insulation max. 13 mm
Insulating cover
Heating cable
Ref. no. Heating output Length Plug type BE Pieces / unit
​ ​
€
223582 16 W 1 m with safety plug 1 blister 1 / blister 1/16 192 ​
223585 32 W 2 m with safety plug 1 blister 1 / blister 1/16 192 ​
223586 64 W 4 m with safety plug 1 blister 1 / blister 1/16 192 ​
223587 128 W 8 m with safety plug 1 blister 1 / blister 1/16 192 ​
223588 192 W 12 m with safety plug 1 blister 1 / blister 1/16 192 ​
223590 224 W 14 m with safety plug 1 blister 1 / blister 1/16 192 ​
223589 288 W 18 m with safety plug 1 blister 1 / blister 1/10 100 ​
223591 384 W 24 m with safety plug 1 blister 1 / blister 1/10 100 ​
223592 592 W 37 m with safety plug 1 blister 1 / blister 1/5 75 ​
223593 784 W 49 m with safety plug 1 blister 1 / blister 1/5 60 ​
Frost-protection heating lines
• prevent water pipes from freezing
• Thermostat in the heating cable switches the cable on automatically
What to remember about 230 V heating cables:
• Always attach the heating cable to the underside of the pipe
• the water pipe must be earthed
• 230 V heating cables are ready to connect and should be connected to a
power supply with a 30 mA residual current circuit breaker
• heating cables must not be shortened and should therefore be ordered
in the correct length
• Excess length can be wound around the pipe (note that a winding
distance of at least 15 mm must be maintained between coils)
• Do not bend heating cables and note the maximum bending radius of
approx. 35 mm
• heating cables can be secured to the pipe with insulating tape or aluminium
tape (222809)
• if using plastic pipes, wrap aluminium tape (222809) around the pipe
before routing the heating cable
• if using plastic pipes, please pay attention to the separate, specific
assembly instructions
• insulate the pipe and heating cable with insulation of max. 13 mm
• attach the heating cable thermostat to the coldest part of the pipe
• insulate the thermostat only moderately
• do not use 230 V heating cables in the bite area of animals
• installation must be carried out by a qualified professional in accordance
with VDE0100
Pipe Ø 15 mm
With insulation (max. 13 mm) frost-resistant
to
Ø 22 mm
½”
Ø 28 mm
¾”
Ø 35 mm
1”
Ø 42 mm
1 ¼”
Ø 48 mm
1 ½”
Ø 60 mm
2”
Ø 76 mm
2 ½”
- 45 °C - 45 °C - 40 °C - 40 °C - 35 °C - 30 °C - 25 °C - 20 °C
245