CPCI-910 Programmer's Guide - Emerson Network Power

More documents

Recommendations

Info

Software Architecture Introduction VLAN INPUT Note: Only the broadcast port will appear in VLAN. Example: 0 | A4,A5 | 1 | A4 | 4 | B3,B4 | 1 | B3 | OVER: TID Trunk id to be created. PORTS List of trunk members separated by commas. PSC Port selection criteria. BCAST_POR T Designated broadcast/DLF port for trunk. Note: All the fields are separated by '|' character. • VLAN This command allows you to create tagged vlans. The syntax for vlan configuration is as follows: SYNTAX | | | INPUT Note: Stack ports should not be included in untagged members. Example: 2 | A0,A1,A2,A3,A4,A5,A6,A7 | A0,A1,A3,A4,A5,A6,A7 | 3 | B0,B1,B2,B3,B4,B5,B6,B7 | B0,B2,B3,B4,B5,B6,B7 | OVER: VLANID vlan id to be created. 1 - 10 CPCI-910
Introduction Software Architecture TAGGED VLAN PORTS UNTAGGED VLAN PORTS PORTCONTROL AUTOLEARN Comma separated list of vlan members. Comma separated list of untagged members of vlan. Note: • Ports specified in UNTAGGED VLAN PORTS are subset of TAGGED VLAN PORTS. • The field separation character '|' is very important. If there are no untagged members in a vlan, the last '|' char is still required. • Port related configuration The syntax for vlan configuration is as follows: SYNTAX PORTS| SPEEDMODE | or PORTS| ON | Note: • Either you can force ports to a particular speed and mode or, you can set them in auto-negotiate mode. • The possible SPEEDMODEs are 10H, 10F, 100H, 100F, 1000H, 1000F • Multiple port listing is separated by the ',' seperator. Example: A3 | 10H | A4 | 100F | A0,A1,A2,A5,A6,A7,B1,B6,B2,B3,B4,B0,B7,B5| ON | OVER: This command allows you to control port speed. • Port learning Port learning allows you to configure MAC address learning behavior on each port. The syntax is as follows. SYNTAX PORTS| ALFLAG| The valid values for ALFLAG are the following: CPCI-910 1 - 11
Page 1 and 2: CPCI-910 Programmer’s Guide P/N 2
Page 3: 221014 410 000 AD World Wide Web: w
Page 6 and 7: List of APIs . . . . . . . . . . .
Page 8 and 9: viii CPCI-910
Page 10 and 11: viii CPCI-910
Page 12 and 13: BIB Board Information Block CMIC CP
Page 14 and 15: Document Number, P/N, or Order Numb
Page 16 and 17: xiv CPCI-910
Page 19 and 20: Introduction Introduction Introduct
Page 21 and 22: Introduction Introduction Packet Dr
Page 23 and 24: Introduction Software Architecture
Page 25: Introduction Software Architecture
Page 29 and 30: Introduction Software Architecture
Page 31: 2 API Call Reference
Page 34 and 35: List of APIs API Call Reference Not
Page 36 and 37: List of APIs API Call Reference int
Page 38 and 39: List of APIs API Call Reference RET
Page 40 and 41: List of APIs API Call Reference the
Page 44 and 45: List of APIs API Call Reference INP
Page 52 and 53: List of APIs API Call Reference Reg
Page 56 and 57: List of APIs API Call Reference dat
Page 64 and 65: List of APIs API Call Reference Tru
Page 74 and 75: List of APIs API Call Reference por
Page 76 and 77:
List of APIs API Call Reference int
Page 78 and 79:
List of APIs API Call Reference RET
Page 80 and 81:
Page 82 and 83:
List of APIs API Call Reference INP
Page 84 and 85:
Page 86 and 87:
List of APIs API Call Reference Por
Page 88 and 89:
List of APIs API Call Reference L3
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
List of APIs API Call Reference hit
Page 96 and 97:
List of APIs API Call Reference ip_
Page 98 and 99:
List of APIs API Call Reference Mul
Page 100 and 101:
List of APIs API Call Reference INC
Page 102 and 103:
List of APIs API Call Reference mod
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
List of APIs API Call Reference 2 -
Page 113 and 114:
Error Codes Error Codes Error Codes
Page 115 and 116:
Error Codes Error Codes Error Code
Page 117:
B Project Configuration and Example
Page 120 and 121:
Project Configuration and Example D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
int bcm_trunk_bitmap_expand() .....
show all

CPCI-910 Programmer's Guide - Emerson Network Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?