L9 Fasteners - UZ Engineered Products
L9 Fasteners - UZ Engineered Products
L9 Fasteners - UZ Engineered Products
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
High Strength Fastening System<br />
Tensile Strength 180,000 PSI minimum<br />
Cap Screws<br />
Hex Nuts<br />
Flatwashers<br />
Locknuts<br />
<strong>Fasteners</strong> with x-tra strength!<br />
Common Problems Associated with Standard <strong>Fasteners</strong>:<br />
• Head separation due to improper material selection, poor heat treat practice, or poor joint design.<br />
• Fatigue failure caused by loss of clamp load, inadequate tightening or poor joint design.<br />
• Cracked or split washers and nuts due to improper material selection, poor material quality or poor heat treat practice.<br />
• Stripped nuts caused by improper strength grade selection, poor heat treat practice, or inadequate nut design.<br />
• Rust and corrosion caused by improper selection of materials and plating for a specific corrosive environment or poor joint design.<br />
The Solution: <strong>L9</strong> Fastening System<br />
• Up to 28% thicker heads for more wrench contact and less slippage.<br />
• Radius under cap screw head adds strength.<br />
• Smooth washer bearing surfaces distribute loads uniformly and reduces brinneling. Plated finish assists torquing.<br />
• Heat treating helps prevent splitting and stripping.<br />
• All components are protected by a Yellow Dichromate finish for maximum corrosion resistance.<br />
Benefits:<br />
You owe it to yourself and your company to compare the difference.<br />
Like many others you will...<br />
• Reduce your fastener usage... and your costs.<br />
• Cut down or completely eliminate costly downtime.<br />
• Keep your equipment, vehicles, etc., on the job longer.<br />
• Improve safety conditions in your operation.<br />
TENSILE STRENGTH: 180,000 PSI minimum.<br />
All components are protected by a Yellow Dichromate finish for maximum corrosion resistance.<br />
1 800 458-4018 www.uzengprod.com<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
93<br />
FASTENERS
FASTENERS<br />
94<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
Compare the difference for yourself...<br />
Can you afford to use less then the best?<br />
High Strength Fastening System<br />
Tensile Strength 180,000 PSI minimum.<br />
The Cap Screw<br />
• Up to 28% thicker heads for the more wrench contact and less slippage.<br />
• Designed and developed for maintenance use.<br />
• Manufactured on the most modern equipment in use today.<br />
• Triple heat treated for ultimate strength.<br />
• Rolled threads eliminate stripping & galling.<br />
• All sizes Made in America!<br />
The Flatwasher<br />
• Develops a full 200,000 PSI COMPRESSIVE strength.<br />
• Through - hardened for greater strength.<br />
• Resists dishing and galling - eliminates loose assemblies.<br />
The Hex Nut<br />
• Thicker than ordinary nuts for greater strength.<br />
• Manufactured from prime SAE approved steel.<br />
• The ONLY nut to use with <strong>L9</strong> Cap Screws.<br />
• Fully finished on all surfaces.<br />
• Clean, sharp, burr-free threads for easier assembly and disassembly.<br />
The Locknut<br />
(Necessary for applications involving severe vibration)<br />
• Designed to stay tight even under heavy vibration conditions.<br />
• Eliminates drilling holes for cotter pins.<br />
• All steel prevailing torque type - no collar or insert.<br />
• Positive locking action - even under difficult conditions.<br />
• Waxed for easier application.<br />
All components are protected by a Yellow Dichromate finish for maximum corrosion resistance.<br />
These specifications EXCEED the requirements of: ASTM B633 FE/ ZN5, Type II (Zinc) and B766, Class 5, Type II (Cadmium)<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 105305<br />
Found on Page 20<br />
PART # 105306<br />
Found on Page 20<br />
PART # 105406<br />
Found on Page 21<br />
PART # 105407<br />
Found on Page 21<br />
FASTENERS
Recommended Tightening Torques<br />
USS Coarse Thread<br />
CLAMP TORQUE BY TORQUE BY TORQUE BY<br />
BOLT LOAD BOLT HEAD NUT<br />
DIA. (LB) (FT-LB) (FT-LB)<br />
1/4-20 3.450 10 11<br />
5/16-18 5,700 19 21<br />
3/8-16 8,450 30 33<br />
7/16-14 11,550 55 60<br />
1/2-13 15,450 85 95<br />
9/16-12 19,800 120 140<br />
5/8-11 24,550 170 185<br />
3/4-10 36,350 265 290<br />
7/8-9 50,300 475 505<br />
1-8 65,900 550 775<br />
1-1/8-7 83,000 1,025 1,150<br />
1-1/4-7 105,400 1,400 1,600<br />
1-1/2-6 152,800 2,900 3,250<br />
SAE Fine Thread<br />
CLAMP TORQUE BY TORQUE BY TORQUE BY<br />
BOLT LOAD BOLT HEAD NUT<br />
DIA. (LB) (FT-LB) (FT-LB)<br />
1/4-28 3,950 12 13<br />
5/16-24 6,300 20 23<br />
3/8-24 9,550 35 38<br />
7/16-20 12,900 60 65<br />
1/2-20 17,400 95 105<br />
9/16-18 22,100 135 150<br />
5/8-18 27,800 190 205<br />
3/4-16 40,600 330 355<br />
7/8-14 55,400 520 585<br />
1-14 73,800 700 900<br />
1-1/8-12 93,100 1,150 1,325<br />
1-1/4-12 116,700 1,600 1,750<br />
1-1/2-12 171,900 3,300 3,650<br />
NOTE:<br />
1. Values are based on using the complete <strong>L9</strong> Fastening combination: Cap Screw, Flatwasher, and Nut.<br />
2. All components are protected by the Yellow Dichromate plating process.<br />
3. Nuts are treated with an industrial quality wax.<br />
These specifications EXCEED the requirements of : ASTM B633 FE/ ZN5, Type II (Zinc) and B766, Class 5, Type II (Cadmium)<br />
1 800 458-4018 www.uzengprod.com<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
95<br />
FASTENERS
FASTENERS<br />
96<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
High Strength Hex Head Cap Screws<br />
Tensile Strength 180,000 PSI Minimum<br />
1/4" DIAMETER 5/16" DIAMETER 3/8" DIAMETER<br />
LENGTH USS (20) SAE (28) QTY. USS (18) SAE (24) QTY. USS (16) SAE (24) QTY.<br />
1/2 01000 02000 50 01010 50 01021 50<br />
3/4 01001 02001 50 01011 02011 50 01022 02022 50<br />
1 01002 02002 50 01012 02012 50 01023 02023 50<br />
1-1/4 01003 02003 50 01013 02013 50 01024 02024 50<br />
1-1/2 01004 02004 50 01014 02014 50 01025 02025 50<br />
1-3/4 01005 50 01015 02015 50 01026 02026 25<br />
2 01006 02006 50 01016 02016 50 01027 02027 25<br />
2- 1/4 01028 02028 25<br />
2-1/2 01007 02007 25 01017 02017 25 01029 02029 25<br />
3 01008 02008 25 01018 02018 25 01030 02030 10<br />
3-1/2 01019 25 01031 02031 10<br />
4 01020 10 01032 02032 10<br />
4-1/2 01033 10<br />
5 01034 10<br />
6 01035 5<br />
<strong>L9</strong> HEX NUT 05661 05674 50 05662 05675 50 05663 05676 50<br />
<strong>L9</strong> FLATWASHER 05010 05010 100 05011 05011 100 05012 05012 100<br />
<strong>L9</strong> LOCKNUT 55204 55214 50 55205 55215 50 55206 55216 50<br />
7/16" DIAMETER 1/2" DIAMETER 9/16" DIAMETER<br />
LENGTH USS (14) SAE (20) QTY. USS (13) SAE (20) QTY. USS (12) SAE (18) QTY.<br />
3/4 01036 25 01048 25<br />
1 01037 02037 25 01049 02049 25 01064 10<br />
1-1/4 01038 02038 25 01050 02050 25<br />
1-1/2 01039 02039 25 01051 02051 25 01065 02065 10<br />
1-3/4 01040 02040 25 01052 02052 25<br />
2 01041 02041 25 01053 02053 25 01066 02066 10<br />
2-1/4 01054 02054 10<br />
2-1/2 01042 02042 25 01055 02055 10 01067 02067 10<br />
3 01043 02043 10 01056 02056 10 01068 02068 10<br />
3-1/2 01044 02044 10 01057 02057 10 01069 02069 10<br />
4 01045 02045 10 01058 02058 10 01070 02070 10<br />
4-1/2 01059 10<br />
5 01046 10 01060 02060 10 01071 10<br />
6 01047 5 01061 02061 5<br />
<strong>L9</strong> HEX NUT 05664 05677 25 05665 05678 10 05666 05679 10<br />
<strong>L9</strong> FLATWASHER 05013 05013 50 05014 05014 50 05015 05015 25<br />
<strong>L9</strong> LOCKNUT 55207 55217 25 55208 55218 25 55209 55219 10<br />
1 800 458-4018 www.uzengprod.com
High Strength Hex Head Cap Screws<br />
Tensile Strength180,000 PSI Minimum<br />
5/8" DIAMETER 3/4" DIAMETER<br />
LENGTH USS(11) SAE (18) QTY. USS (10) SAE (16) QTY.<br />
1 01072 02072 10<br />
1-1/4 01073 10<br />
1-1/2 01074 02074 10 01093 02093 10<br />
1-3/4 01075 02075 10 01094 10<br />
2 01076 02076 10 01095 02095 10<br />
2-1/4 01077 02077 10 01096 02096 10<br />
2-1/2 01078 02078 10 01097 02097 10<br />
2-3/4 01079 02079 10 01098 02098 10<br />
3 01080 02080 10 01099 02099 10<br />
3-1/2 01081 02081 10 01100 02100 10<br />
4 01082 02082 10 01101 02101 5<br />
4-1/2 01083 02083 10 01102 02102 5<br />
5 01084 02084 10 01103 02103 5<br />
5-1/2 01085 02085 10 01104 5<br />
6 01086 02086 5 01105 02105 5<br />
7 105689 1<br />
<strong>L9</strong> HEX NUT 05667 05680 10 05668 05681 10<br />
<strong>L9</strong> FLATWASHER 05016 05016 25 05017 05017 25<br />
<strong>L9</strong> LOCKNUT 55210 55220 10 55211 55221 10<br />
7/8" DIAMETER 1" DIAMETER<br />
LENGTH USS(9) SAE (14) QTY. USS (8) SAE (14) QTY.<br />
2 01112 5 01127 5<br />
2-1/2 01113 02113 5 01128 02128 5<br />
3 01114 02114 5 01129 02129 5<br />
3-1/2 01115 02115 5 01130 5<br />
4 01116 02116 5 01131 02131 5<br />
4-1/2 01117 02117 5 01132 02132 5<br />
5 01118 02118 5 01133 02133 5<br />
5-1/2 01134 5<br />
6 01120 02120 5 01135 02135 5<br />
<strong>L9</strong> HEX NUT 05669 05682 5 05670 05683 5<br />
<strong>L9</strong> FLATWASHER 05018 05018 10 05019 05019 10<br />
<strong>L9</strong> LOCKNUT 55212 55222 5 55213 55223 5<br />
1 800 458-4018 www.uzengprod.com<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
All Components Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
These specification EXCEED the requirements of : ASTM B633 FE/ ZN5, Type II (Zinc) and B766, Class 5, Type II (Cadmium)<br />
97<br />
FASTENERS
FASTENERS<br />
98<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
High Strength Hex Nuts<br />
Tensile Strength 180,000 PSI Minimum<br />
Look for the <strong>L9</strong> ® stamp on every nut! It's our quality guarantee!<br />
• Thicker than ordinary hex nuts.<br />
• Manufactured only from prime SAE approved steel.<br />
• Clean, sharp, burr-free threads for easier assembly.<br />
• Fully finished on all surfaces for greater reliability.<br />
• Designed to be used with the <strong>L9</strong> ® Cap Screw to<br />
achieve maximum clamping force.<br />
There is a difference in <strong>L9</strong> ® Hex Nuts...See for yourself!<br />
Thicker for greater strength! Resists splitting under load!<br />
<strong>L9</strong> ® Hex Nuts are thicker than the ordinary Ordinary hex nuts can split under load and cause premature<br />
hex nuts... This means more thread engagement and dangerous fastener failure. The thicker, heat-treated <strong>L9</strong> ® Nut<br />
and greater clamping force. is designed to resist splitting, even in the toughest applications.<br />
DIMENSIONS<br />
USS SAE WIDTH ACROSS THICKNESS<br />
SIZE PART # SIZE PART # QTY. FLATS (MAX.) HEIGHT (MAX.)<br />
1/4-20 05661 1/4-28 05674 50 .437 .264<br />
5/16-18 05662 5/16-24 05675 50 .500 .309<br />
3/8-16 05663 3/8-24 05676 50 .562 .377<br />
7/16-14 05664 7/16-20 05677 25 .687 .445<br />
1/2-13 05665 1/2-20 05678 10 .750 .511<br />
9/16-12 05666 9/16-18 05679 10 .875 .575<br />
5/8-11 05667 5/8-18 05680 10 .937 .655<br />
3/4-10 05668 3/4-16 05681 10 1.125 .762<br />
7/8-9 05669 7/8-14 05682 5 1.312 .882<br />
1-8 05670 1-14 05683 5 1.500 1.018<br />
1 1/4-7 05672 2 1.875 1.272<br />
1 800 458-4018 www.uzengprod.com
High Strength Lock Nuts<br />
Tensile Strength 180,000 PSI Minimum<br />
• Designed to stay tight even under severe vibration conditions.<br />
• All steel prevailing torque - type no collar or insert.<br />
• Positive locking action - even under difficult conditions.<br />
• Waxed for easier applications.<br />
DIMENSIONS<br />
USS SAE WIDTH ACROSS THICKNESS<br />
SIZE PART # SIZE PART # QTY. FLATS (MAX.) HEIGHT (MAX.)<br />
High Strength Flatwashers<br />
Tensile Strength 180,000 PSI Minimum<br />
• Our <strong>L9</strong> Flatwasher... designed to provide<br />
excellent service in normal applications.<br />
• Through-hardened... develops a full 200,000 PSI COMPRESSIVE STRENGTH.<br />
• Much stronger than ordinary flatwashers.<br />
SAE<br />
BOLT INSIDE OUTSIDE (NOMINAL)<br />
SIZE PART # QTY. DIAMETER DIAMETER THICKNESS<br />
1/4 05010 100 9/32 5/8 1/16<br />
5/16 05011 100 11/32 11/16 1/16<br />
3/8 05012 100 13/32 13/16 1/16<br />
7/16 05013 50 15/32 59/64 1/16<br />
1/2 05014 50 17/32 1-1/16 7/64<br />
9/16 05015 25 19/32 1-3/16 7/64<br />
5/8 05016 25 11/16 1-5/16 1/8<br />
3/4 05017 25 13/16 1-15/32 1/8<br />
7/8 05018 10 15/16 1-3/4 9/64<br />
1 05019 10 1-1/8 2 9/64<br />
1-1/8 05655 5 1-1/4 2-1/4 11/64<br />
1-1/4 05656 5 1-3/8 2-1/2 11/64<br />
1-1/2 05657 5 1-5/8 3 11/64<br />
1 800 458-4018 www.uzengprod.com<br />
<strong>L9</strong> <strong>Fasteners</strong><br />
1/4-20 55204 1/4-28 55214 50 .437 .301<br />
5/16-18 55205 5/16-24 55215 50 .500 .336<br />
3/8-16 55206 3/8-24 55216 50 .562 .400<br />
7/16-14 55207 7/16-20 55217 25 .687 .449<br />
1/2-13 55208 1/2-20 55218 25 .750 .516<br />
9/16-12 55209 9/16-18 55219 10 .875 .580<br />
5/8-11 55210 5/8-18 55220 10 .937 .660<br />
3/4-10 55211 3/4-16 55221 10 1.125 .767<br />
7/8-9 55212 7/8-14 55222 5 1.312 .887<br />
1-8 55213 1-14 55223 5 1.500 1.023<br />
All Components Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
These specifications EXCEED the requirements of : ASTM B633 FE/ ZN5, Type II (Zinc) and B766, Class 5, Type II (Cadmium)<br />
All Components Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
These specifications EXCEED the requirements of : ASTM B633 FE/ ZN5, Type II (Zinc) and B766, Class 5, Type II (Cadmium)<br />
99<br />
FASTENERS HARDWARE
FASTENERS<br />
100<br />
Grade 8 <strong>Fasteners</strong><br />
Grade 8 Cap Screws<br />
Tensile Strength 150,000 PSI Minimum<br />
• High quality.<br />
• Chamfered edges for easy starting.<br />
• Clean threads - burr-free.<br />
• Full finished dimensions.<br />
• Washer-faced head.<br />
• Conforms to SAE J429 and<br />
Meets MIL Spec MIL-DTL-1222J.<br />
• Lengths longer than 6” will be plain finish<br />
1/4" DIAMETER 5/16" DIAMETER 3/8" DIAMETER<br />
LENGTH USS (20) SAE (28) QTY. USS (18) SAE (24) QTY. USS (16) SAE (24) QTY.<br />
1/2 01600 272170 100 01610 272189 100 01621 272208 75<br />
3/4 01601 272171 100 01611 272190 100 01622 272209 75<br />
1 01602 272172 100 01612 272191 100 01623 272210 75<br />
1-1/4 01603 272173 100 01613 272192 75 01624 272211 75<br />
1-1/2 01604 272174 100 01614 272193 75 01625 272212 50<br />
1-3/4 01605 272175 75 01615 272194 50 01626 272213 50<br />
2 01606 272176 75 01616 272195 50 01627 272214 25<br />
2-1/4 272007 272177 75 272026 272196 50 01628 272215 25<br />
2-1/2 01607 272178 50 01617 272197 50 01629 272216 25<br />
2-3/4 272009 272179 50 272028 272198 25 272047 25<br />
3 01608 272180 50 01618 272199 25 01630 272218 25<br />
3-1/4 272011 272181 25 272030 272200 25 272049 25<br />
3-1/2 272012 272182 25 272031 272201 25 272050 272220 25<br />
3-3/4 272013 272183 25 272032 272202 25 272051 272221 20<br />
4 272014 272184 25 272033 272203 20 272052 272222 20<br />
4-1/2 272015 25 272034 20 272053 272223 10<br />
5 272016 25 272035 20 272054 272224 10<br />
5-1/2 272017 20 272036 10 272055 272225 10<br />
6 272018 20 272037 272207 10 272056 272226 10<br />
Gr8 HEX NUT 01216 02216 100 01217 02217 100 01218 02218 100<br />
Gr8 FLATWASHER 55224 55234 200 55225 55235 200 55226 55236 150<br />
Gr8 LOCKWASHER 05020 05020 200 05021 05021 200 05022 05022 150<br />
GrC STEEL LOCKNUT 01226 02226 100 01227 02227 100 01228 02228 100<br />
6-1/2 104041 1<br />
7 104042 1<br />
7-1/2 104023 1<br />
8 104024 104044 1<br />
8-1/2 1<br />
9 104046 1<br />
All Components Up To And Including 6” Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com
Grade 8 Cap Screws<br />
Tensile Strength 150,000 PSI Minimum<br />
Grade 8 <strong>Fasteners</strong><br />
7/16" DIAMETER 1/2" DIAMETER 9/16" DIAMETER<br />
LENGTH USS (14) SAE (20) QTY. USS (13) SAE (20) QTY. USS (12) SAE (18) QTY.<br />
3/4 01636 272227 75 01648 272245 25<br />
1 01637 272228 75 01649 272246 25 272093 272263 10<br />
1-1/4 01638 272229 75 01650 272247 25 272094 272264 10<br />
1-1/2 01639 272230 50 01651 272248 25 272095 272265 10<br />
1-3/4 01640 272231 25 01652 272249 25 272096 272266 10<br />
2 01641 272232 25 01653 272250 25 272097 272267 10<br />
2-1/4 272063 272233 25 01654 272251 20 272098 272268 10<br />
2-1/2 01642 272234 25 01655 272252 20 272099 272269 5<br />
2-3/4 272065 272235 20 272083 272253 20<br />
3 01643 272236 20 01656 272254 20 272101 272271 5<br />
3-1/4 272067 20 272085 272255 10<br />
3-1/2 272068 272238 20 272086 272256 10 272103 272273 5<br />
3-3/4 272069 20 272257 10<br />
4 272070 272240 10 272088 272258 10 272105 272275 5<br />
4-1/2 272071 272241 10 272089 272259 10 272106 272276 5<br />
5 272072 272242 10 272090 272260 10 272107 272277 5<br />
5-1/2 272073 10 272091 272261 10 272108 272278 5<br />
6 272074 10 272092 272262 10 272109 272279 5<br />
Gr8 HEX NUT 01219 02219 50 01220 02220 50 01221 02221 25<br />
Gr8 FLATWASHER 55227 55237 75 55228 55238 75 55229 55239 50<br />
Gr8 LOCKWASHER 05023 05023 75 05024 05024 75 05025 05025 50<br />
Gr8 STEEL LOCKNUT 01229 02229 50 01230 02230 50 01231 02231 25<br />
6-1/2 104061 1 104081 104381 1<br />
7 104062 1 104082 104382 1<br />
7-1/2 104083 1<br />
8 104084 104384 1<br />
8-1/2 104085 1<br />
9 104086 1<br />
9-1/2 104087 1<br />
14 104096 1<br />
All Components Up To And Including 6” Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
See Pages 22-31<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
Assortments & Modules<br />
101<br />
FASTENERS
FASTENERS<br />
102<br />
Grade 8 <strong>Fasteners</strong><br />
Grade 8 Cap Screws<br />
Tensile Strength 150,000 PSI Minimum<br />
5/8" DIAMETER 3/4" DIAMETER<br />
LENGTH USS (11) SAE (18) QTY. USS (10) SAE (16) QTY.<br />
1 272110 272280 20 272127 10<br />
1-1/4 272111 272281 20 272128 10<br />
1-1/2 272112 272282 20 272129 272299 10<br />
1-3/4 272113 272283 20 272130 272300 10<br />
2 272114 272284 20 272131 272301 10<br />
2-1/4 272115 272285 10 272132 272302 10<br />
2-1/2 272116 272286 10 272133 272303 10<br />
2-3/4 272117 272287 10 272134 272304 10<br />
3 272118 272288 10 272135 272305 10<br />
3-1/4 272119 272289 10 272136 272306 5<br />
3-1/2 272120 272290 10 272137 272307 5<br />
3-3/4 272138 5<br />
4 272122 272292 10 272139 272309 5<br />
4-1/2 272123 272293 10 272140 272310 5<br />
5 272124 272294 5 272141 271311 5<br />
5-1/2 272125 272295 5 272142 271312 5<br />
6 272126 272296 5 272143 272313 5<br />
Gr8 HEX NUT 01222 02222 25 01223 02223 10<br />
Gr8 FLATWASHER 55230 55240 50 55231 55241 50<br />
Gr8 LOCKWASHER 05026 05026 50 05027 05027 50<br />
GrC STEEL LOCKNUT 01232 02232 25 01233 02233 10<br />
6-1/2 104121 104421 1 104141 104441 1<br />
7 104122 104422 1 104142 1<br />
7-1/2 104123 104423 1 104143 1<br />
8 104124 104424 1 104144 1<br />
8-1/2 104125 104425 1 104145 1<br />
9 104126 1 104146 1<br />
10 104148 1<br />
10-1/2 104429 1<br />
11 104150 1<br />
12-1/2 104133 1<br />
13-1/2 104135 1<br />
All Components Up To And Including 6” Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com
7/8" DIAMETER 1" DIAMETER<br />
LENGTH USS (9) SAE (14) QTY. USS (8) SAE (14) QTY.<br />
2 272144 272314 10 272157 272327 5<br />
2-1/4 272145 10<br />
2-1/2 272146 272316 5 272159 272329 5<br />
3 272148 272318 5 272161 272331 5<br />
3-1/2 272150 272320 5 272163 272333 5<br />
4 272152 272322 5 272165 272335 5<br />
4-1/2 272153 272323 5 272166 272336 5<br />
5 272154 272324 5 272167 272337 5<br />
5-1/2 272155 272325 5 272168 272338 5<br />
6 272156 272326 5 272169 272339 5<br />
Gr8 HEX NUT 01224 02224 10 01225 02225 10<br />
Gr8 FLATWASHER 55232 55242 20 55233 55243 10<br />
Gr8 LOCKWASHER 05028 05028 20 05029 05029 10<br />
GrC STEEL LOCKNUT 01234 02234 10 01235 02235 10<br />
6-1/2 104161 1 104181 1<br />
7 104182 1<br />
7-1/2 104183 1<br />
8 104184 104484 1<br />
9 104466 1 1<br />
9-1/2 1 104487 1<br />
12 104172 1<br />
1-1/4" DIAMETER 1-1/2" DIAMETER<br />
LENGTH USS (7) SAE (12) QTY. USS (6) SAE (12) QTY.<br />
6-1/2 104221 1<br />
8 104224 1 104244 1<br />
13 104234 1<br />
Grade 8 <strong>Fasteners</strong><br />
All Components Up To And Including 6” Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com<br />
103<br />
FASTENERS
FASTENERS<br />
104<br />
Grade 8 <strong>Fasteners</strong><br />
Grade 8 Cap Screws - Plain Finish*<br />
• Tensile strength 150,000PSI minimum (SAE Grade 8)<br />
• Conforms to SAE J429 material and mechanical properties<br />
• Product dimensions are to ASME B18.2.1<br />
1 800 458-4018 www.uzengprod.com<br />
• Rockwell “C” hardness 33-39<br />
• Unplated or plain finish<br />
• North American Manufactured<br />
1/4" DIAMETER 5/16" DIAMETER 3/8" DIAMETER<br />
LENGTH USS (20) SAE (28) QTY. USS (18) SAE (24) QTY. USS (16) SAE (24) QTY.<br />
1/2 983535 983556 100 983577 983598 100 983619 983640 100<br />
5/8 983536 983557 100 983578 983599 100 983620 983641 100<br />
3/4 983537 983558 100 983579 983600 100 983621 983642 100<br />
7/8 983538 983559 100 983580 983601 100 983622 983643 100<br />
1 983539 983560 100 983581 983602 100 983623 983644 100<br />
1-1/4 983540 983561 100 983582 983603 100 983624 983645 100<br />
1-1/2 983541 983562 100 983583 983604 100 983625 983646 100<br />
1-3/4 983542 983563 100 983584 983605 100 983626 983647 100<br />
2 983543 983564 100 983585 983606 100 983627 983648 100<br />
2-1/4 983544 983565 100 983586 983607 100 983628 983649 100<br />
2-1/2 983545 983566 100 983587 983608 100 983629 983650 100<br />
2-3/4 983546 983567 100 983588 983609 100 983630 983651 100<br />
3 983547 983568 100 983589 983610 100 983631 983652 100<br />
3-1/4 983548 983569 50 983590 983611 50 983632 983653 50<br />
3-1/2 983549 983570 50 983591 983612 50 983633 983654 50<br />
3-3/4 983550 983571 50 983592 983613 50 983634 983655 50<br />
4 983551 983572 50 983593 983614 50 983635 983656 50<br />
4-1/2 983552 983573 50 983594 983615 50 983636 983657 50<br />
5 983553 983574 50 983595 983616 50 983637 983658 50<br />
5-1/2 983554 983575 50 983596 983617 50 983638 983659 50<br />
6 983555 983576 50 983597 983618 50 983639 983660 50<br />
Grade 8 400181 400191 100 400182 400192 100 400183 400193 100<br />
Hex Nut Plain<br />
7/16" DIAMETER 1/2" DIAMETER 9/16" DIAMETER<br />
LENGTH USS (14) SAE (20)QTY. USS (13) SAE (20) QTY. USS (12) SAE (18)QTY.<br />
1/2<br />
5/8<br />
3/4 983661 983680 100 983699 983718 50<br />
7/8 983662 983681 100 983700 983719 50<br />
1 983663 983682 100 983701 983720 50 983737 983752 25<br />
1-1/4 983664 983683 50 983702 983721 50 983738 983753 25<br />
1-1/2 983665 983684 50 983703 983722 50 983739 983754 25<br />
1-3/4 983666 983685 50 983704 983723 50 983740 983755 25<br />
2 983667 983686 50 983705 983724 50 983741 983756 25<br />
2-1/4 983668 983687 50 983706 983725 50 983742 983757 25<br />
2-1/2 983669 983688 50 983707 983726 50 983743 983758 25<br />
2-3/4 983670 983689 50 983708 983727 50 983744 983759 25<br />
3 983671 983690 50 983709 983728 50 983745 983760 25<br />
3-1/4 983672 983691 25 983710 983729 25<br />
3-1/2 983673 983692 25 983711 983730 25 983746 983761 25<br />
3-3/4 983674 983693 25 983712 983731 25<br />
4 983675 983694 25 983713 983732 25 983747 983762 25<br />
4-1/2 983676 983695 25 983714 983733 25 983748 983763 25<br />
5 983677 983696 25 983715 983734 25 983749 983764 25<br />
5-1/2 983678 983697 25 983716 983735 25 983750 983765 25<br />
6 983679 983698 25 983717 983736 25 983751 983766 25<br />
Grade 8 400184 400194 100 400185 400195 100 400186 400196 100<br />
Hex Nut Plain<br />
*Denotes non-stock item
Grade 8 Cap Screws - Plain Finish*<br />
• Tensile strength 150,000PSI minimum (SAE Grade 8)<br />
• Conforms to SAE J429 material and mechanical properties<br />
• Product dimensions are to ASME B18.2.1<br />
5/8" DIAMETER 3/4" DIAMETER 7/8" DIAMETER<br />
LENGTH USS (11) SAE (18)QTY. USS (10) SAE (16)QTY. USS (9) SAE (14) QTY.<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1 983767 983784 25 983801 983818 25<br />
1-1/4 983768 983785 25 983802 983819 25<br />
1-1/2 983769 983786 25 983803 983820 25 983835 983850 15<br />
1-3/4 983770 983787 25 983804 983821 25 983836 983851 15<br />
2 983771 983788 25 983805 983822 25 983837 983852 15<br />
2-1/4 983772 983789 25 983806 983823 25 983838 983853 15<br />
2-1/2 983773 983790 25 983807 983824 25 983839 983854 15<br />
2-3/4 983774 983791 25 983808 983825 25 983840 983855 15<br />
3 983775 983792 25 983809 983826 25 983841 983856 15<br />
3-1/4 983776 983793 25 983810 983827 25 983842 983857 15<br />
3-1/2 983777 983794 25 983811 983828 25 983843 983858 15<br />
3-3/4 983778 983795 25 983812 983829 25 983844 983859 15<br />
4 983779 983796 25 983813 983830 25 983845 983860 15<br />
4-1/2 983780 983797 25 983814 983831 25 983846 983861 15<br />
5 983781 983798 25 983815 983832 25 983847 983862 15<br />
5-1/2 983782 983799 25 983816 983833 25 983848 983863 15<br />
6 983783 983800 25 983817 983834 25 983849 983864 15<br />
Grade 8 400187 400197 50 400188 400198 50 400189 400199 25<br />
Hex Nut Plain<br />
1" DIAMETER<br />
LENGTH USS (8) SAE (14) QTY.<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2 983865 983879 10<br />
1-3/4 983866 983880 10<br />
2 983867 983881 10<br />
2-1/4 983868 983882 10<br />
2-1/2 983869 983883 10<br />
2-3/4 983870 983884 10<br />
3 983871 983885 10<br />
3-1/4 983872 983886 10<br />
3-1/2 983873 983887 10<br />
3-3/4<br />
4 983874 983888 10<br />
4-1/2 983875 983889 10<br />
5 983876 983890 10<br />
5-1/2 983877 983891 10<br />
6 983878 983892 10<br />
Grade 8 400190 400200 25<br />
Hex Nut Plain<br />
*Denotes non-stock item<br />
• Rockwell “C” hardness 33-39<br />
• Unplated or plain finish<br />
• North American Manufactured<br />
Grade 8 Hex Nuts Plain *<br />
Grade 8 <strong>Fasteners</strong><br />
• Use with Grade 8 Cap Screws • Meets ASME/ANSI B18.2.2-1987 and SAE J995<br />
• Full chamfer for positive wrenching • Plain or unplated finish<br />
USS SAE WIDTH THICKNESS QTY<br />
SIZE PART # SIZE PART # ACROSS FLATS<br />
1/4-20 400181 1/4-28 400191 7/16 7/32 100<br />
5/16-18 400182 5/16-24 400192 1/2 17/64 100<br />
3/8-16 400183 3/8-24 400193 9/16 21/64 100<br />
7/16-14 400184 7/16-20 400194 11/16 3/8 100<br />
1/2-13 400185 1/2-20 400195 3/4 7/16 100<br />
9/16-12 400186 9/16-18 400196 7/8 31/64 100<br />
5/8-11 400187 5/8-18 400197 15/16 35/64 50<br />
3/4-10 400188 3/4-16 400198 1-1/8 41/64 50<br />
7/8-9 400189 7/8-14 400199 1-5/16 3/4 25<br />
1-8 400190 1-14 400200 1-1/2 55/64 25<br />
*Denotes non-stock item<br />
1 800 458-4018 www.uzengprod.com<br />
105<br />
FASTENERS
FASTENERS<br />
106<br />
Grade 8 <strong>Fasteners</strong><br />
Grade 8 Hex Nuts<br />
• Full chamfer for positive wrenching.<br />
• Full finished dimensions.<br />
• Use with Grade 8 Cap Screws.<br />
• Clean burr-free threads.<br />
• Washer-faced for full seating.<br />
• Conforms to SAE J429 and<br />
Meets MIL Spec MIL-DTL-1222J.<br />
• Plated<br />
USS SAE<br />
WIDTH<br />
ACROSS<br />
SIZE PART # SIZE PART # FLATS THICKNESS QTY.<br />
1/4-20 01216 1/4-28 02216 7/16 7/32 100<br />
5/16-18 01217 5/16-24 02217 1/2 17/64 100<br />
3/8-16 01218 3/8-24 02218 9/16 21/64 100<br />
7/16-14 01219 7/16-20 02219 11/16 3/8 50<br />
1/2-13 01220 1/2-20 02220 3/4 7/16 50<br />
9/16-12 01221 9/16-18 02221 7/8 31/64 25<br />
5/18-11 01222 5/8-18 02222 15/16 35/64 25<br />
3/4-10 01223 3/4-16 02223 1-1/8 41/64 10<br />
7/8-9 01224 7/8-14 02224 1-5/16 3/4 10<br />
1-8 01225 1-14 02225 1-1/2 55/64 10<br />
All Steel Locknuts-Grade C<br />
• Positive multiple locking surface to resist vibration.<br />
• Use with Grade 8 Cap Screws.<br />
USS SAE<br />
WIDTH<br />
ACROSS<br />
SIZE PART # SIZE PART # FLATS THICKNESS QTY.<br />
1/4-20 01226 1/4-28 02226 7/16 7/32 100<br />
5/16-18 01227 5/16-24 02227 1/2 17/64 100<br />
3/8-16 01228 3/8-24 02228 9/16 21/64 100<br />
7/16-14 01229 7/16-20 02229 11/16 3/8 50<br />
1/2-13 01230 1/2-20 02230 3/4 7/16 50<br />
9/16-12 01231 9/16-18 02231 7/8 31/64 25<br />
5/18-11 01232 5/8-18 02232 15/16 35/64 25<br />
3/4-10 01233 3/4-16 02233 1-1/8 41/64 10<br />
7/8-9 01234 7/8-14 02234 1-5/16 47/64 10<br />
1-8 01235 1-14 02235 1-1/2 27/32 10<br />
All Components Are Protected By A Plated Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com
Nylon Insert Lock Nuts (Elastic stop nuts)<br />
Keeps fastener assemblies tight when vibration is present<br />
• Use with Grade 8 Capscrews<br />
• Uni-Zinc Plated to resist rust and corrosion<br />
USS (NC) SAE (NF)<br />
SIZE PART # Qty PART # SIZE QTY<br />
1/4-20 107356 40 107357 1/4-28 40<br />
5/16-18 107358 35 107359 5/16-24 35<br />
3/8-16 107360 30 107361 3/8-24 30<br />
7/16-14 107362 25 107363 7/16-20 25<br />
1/2-13 107364 20 107365 1/2-20 20<br />
9/16-12 107366 15 107367 9/16-18 15<br />
5/8-11 107368 10 107369 5/8-18 10<br />
3/4-10 107370 10 107371 3/4-16 10<br />
7/8-9 107372 5 107373 7/8-14 5<br />
1-8 107374 5 107375 1-14 5<br />
1-1/8-7 107376 2 107377 1-1/8-12 2<br />
1-1/4-7 107378 1 107379 1-1/4-12 1<br />
1-3/8-6 107380 1 107381 1-3/8-12 1<br />
1-1/2-6 107382 1 107383 1-1/2-12 1<br />
Grade 8 Flatwashers<br />
• Use with Grade 8 Cap Screws.<br />
• Precision stamped from prime quality medium carbon steel.<br />
• Through hardened to RC 38-45.<br />
• Smooth, burr-free surfaces.<br />
Grade 8 <strong>Fasteners</strong><br />
USS SAE<br />
SIZE PART # O.D I.D WIDTH QTY. SIZE PART # O.D I.D WIDTH QTY.<br />
1/4-20 55224 0.750 0.312 .055/.072 200 1/4-28 55234 0.625 0.281 .055/.072 200<br />
5/16-18 55225 0.875 0.375 .064/.080 200 5-16-24 55235 0.688 0.344 .064/.080 200<br />
3/8-16 55226 1.000 0.438 .064/.080 150 3/8-24 55236 0.813 0.406 .064/.080 150<br />
7/16-14 55227 1.250 0.500 .064/.080 75 7/16-20 55237 0.923 0.469 .064/.080 75<br />
1/2-13 55228 1.375 0.563 .097/.121 75 1/2-20 55238 1.063 0.531 .097/.121 75<br />
9/16-12 55229 1.500 0.625 .097/.121 50 9/16-18 55239 1.180 0.593 .097/.121 50<br />
5/8-11 55230 1.750 0.688 .122/.146 50 5/8-18 55240 1.313 0.656 .122/.146 50<br />
3/4-10 55231 2.000 0.813 .122/.146 50 3/4-16 55241 1.468 0.812 .122/.146 50<br />
7/8-9 55232 2.250 0.938 .136/.160 20 7/8-14 55242 1.750 0.937 .136/.160 20<br />
1-8 55233 2.500 1.063 .136/.160 10 1-14 55243 2.000 1.063 .136/.160 10<br />
All Components Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com<br />
107<br />
FASTENERS
FASTENERS<br />
108<br />
Grade 8 <strong>Fasteners</strong><br />
GR8 X-TRA Thick Flatwashers<br />
• Use with Grade 8 Cap Screws, A325 and A490 Cap Screws<br />
• Fabricated from prime quality medium carbon steel<br />
• Through hardened to R/C 38-45<br />
• Uniform load distribution<br />
• Zinc plated to resist rust and corrosion<br />
USS SAE<br />
SIZE PART # O.D. I.D. THICKNESS QTY. SIZE PART # O.D. I.D. THICKNESS QTY.<br />
1/4-20 116244 3/4 5/16 .090 - .110 100 1/4-28 116254 5/8 9/32 .090 - .110 100<br />
5/16-18 116245 7/8 3/8 .090 - .110 100 5/16-24 116255 11/16 11/32 .090 - .110 100<br />
3/8-16 116246 1 7/16 .110 - .126 50 3/8-24 116256 13/16 13/32 .110 - .126 50<br />
7/16-14 116247 1-1/4 1/2 .110 - .126 50 7/16-20 116257 59/64 15/32 .110 - .126 50<br />
1/2-13 116248 1-3/8 9/16 .156 - .188 25 1/2-20 116258 1-1/16 17/32 .156 - .188 25<br />
9/16-12 116249 1-1/2 5/8 .156 - .188 10 9/16-18 116259 1-3/16 19/32 .156 - .188 10<br />
5/8-11 116250 1-3/4 11/16 .170 - .195 10 5/8-18 116260 1-5/16 21/32 .170 - .195 10<br />
3/4-10 116251 2 13/16 .170 - .195 10 3/4 -16 116261 1-15/32 13/16 .170 - .195 10<br />
7/8-9 116252 2-1/4 15/16 .235 - .265 5 7/8-14 116262 1-3/4 15/16 .235 - .265 5<br />
1-8 116253 2-1/2 1-1/16 .235 - .265 5 1-14 116263 2 1-1/16 .235 - .265 5<br />
Grade 8 Lockwashers<br />
For use with Grade 8 Cap Screws!<br />
Up to 23% thicker than ordinary lockwashers!<br />
• The extra thickness helps assure longer equipment life.<br />
• Compensates for wear through increased spring tension.<br />
• Reduces loss in tightness due to vibration.<br />
• Will not warp or lose tension.<br />
• Retains strength and holding power where ordinary washers fail.<br />
• Eliminates cracking and breaking.<br />
BOLT NOM. INSIDE WASHER SECTION<br />
SIZE PART # QTY. DIAMETER WIDTH THICKNESS<br />
1/4 05020 200 17/64 .110 .077<br />
5/16 05021 200 21/64 .130 .097<br />
3/8 05022 150 25/64 .145 .115<br />
7/16 05023 75 29/64 .160 .133<br />
1/2 05024 75 33/64 .176 .151<br />
9/16 05025 50 37/64 .193 .170<br />
5/8 05026 50 41/64 .210 .189<br />
3/4 05027 50 49/64 .244 .226<br />
7/8 05028 20 57/64 .281 .266<br />
1 05029 10 1-1/64 .319 .306<br />
All Components Are Protected By A Yellow Dichromate Finish For Maximum Corrosion Resistance.<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
Assortments<br />
Part #00497 found on page 42<br />
Part #00498 found on page 42
Grade 5 Cap Screws<br />
Tensile Strength 120,000 PSI Minimum<br />
• Manufactured from SAE approved C-1038 steel.<br />
• Double-heat treated for greater strength.<br />
• Exceeds SAE Grade 5 specifications.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
• Washer faced for positive seating on uneven surfaces.<br />
• Conforms to SAE J425 and Mil Spec MIL-DTL-1222J.<br />
1/4" Diameter 5/16" Diameter<br />
THREAD PITCH: USS 1/4-20 SAE 1/4-28 THREAD PITCH: USS 5/16-18 SAE 5/16-24<br />
WIDTH ACROSS FLATS: 7/16" WIDTH ACROSS FLATS: 1/2"<br />
HEAD HEIGHT (MAX): 5/32 HEAD HEIGHT (MAX): 13/64<br />
USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY.<br />
1/2 03000 04000 100<br />
5/8 110102 100<br />
3/4 03001 04001 100<br />
7/8 110104 100<br />
1 03002 04002 100<br />
1-1/4 03003 04003 100<br />
1-1/2 03004 04004 100<br />
1-3/4 03005 04005 75<br />
2 03006 04006 75<br />
2-1/4 03007 04007 75<br />
2-1/2 03008 04008 50<br />
2-3/4 03009 04009 50<br />
3 03010 04010<strong>UZ</strong> 50<br />
3-1/4 110114 110466 25<br />
3-1/2 03011 04011 25<br />
3-3/4 110116 110467 25<br />
4 03012 04012 25<br />
4-1/2 03013 04013 25<br />
5 03014 04014 25<br />
5-1/2 03015 04015 20<br />
6 03016 04016 20<br />
Hex Nut 110821 110848 100<br />
Nylon Insert<br />
Locknut<br />
05060 05070 50<br />
Flatwasher 05116 05126 200<br />
Lockwasher 05136 05136 200<br />
Available in<br />
Assortments & Modules<br />
See Page 32 - 39<br />
Grade 5 <strong>Fasteners</strong><br />
USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY.<br />
1/2 03017 04017 100<br />
5/8 110137 100<br />
3/4 03018 04018 100<br />
7/8 110139 100<br />
1 03019 04019 100<br />
1-1/4 03020 04020 75<br />
1-1/2 03021 04021 75<br />
1-3/4 03022 04022 50<br />
2 03023 04023 50<br />
2-1/4 03024 04024 50<br />
2-1/2 03025 04025 50<br />
2-3/4 03026 04026 25<br />
3 03027 04027 25<br />
3-1/4 110149 110499 25<br />
3-1/2 03028 04028 25<br />
3-3/4 110151 110501 25<br />
4 03029 04029 20<br />
4-1/2 03030 04030 20<br />
5 03031 04031 20<br />
5-1/2 03032 04032 10<br />
6 03033 04033 10<br />
Hex Nut 110822 110849 100<br />
Nylon Insert<br />
Locknut<br />
05061 05071 50<br />
Flatwasher 05117 05127 200<br />
Lockwasher 05137 05137 150<br />
1 800 458-4018 www.uzengprod.com<br />
109<br />
FASTENERS
FASTENERS<br />
110<br />
Grade 5 <strong>Fasteners</strong><br />
Grade 5 Cap Screws<br />
Tensile Strength 120,000 PSI Minimum<br />
3/8" Diameter 7/16" Diameter<br />
THREAD PITCH: USS 3/8-16 SAE 38-24 THREAD PITCH: USS 7/16-14 SAE 7/16-20<br />
WIDTH ACROSS FLATS: 9/16" WIDTH ACROSS FLATS: 5/8"<br />
HEAD HEIGHT (MAX): 15/64 HEAD HEIGHT (MAX): 19/64<br />
USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY.<br />
1/2 03034 04034 75<br />
5/8 110172 75<br />
3/4 03035 04035 75<br />
7/8 110174 75<br />
1 03036 04036 75<br />
1-1/4 03037 04037 75<br />
1-1/2 03038 04038 50<br />
1-3/4 03039 04039 50<br />
2 03040 04040 25<br />
2-1/4 03041 04041 25<br />
2-1/2 03042 04042 25<br />
2-3/4 03043 04043 25<br />
3 03044 04044 25<br />
3-1/4 110184 110534 25<br />
3-1/2 03045 04045 25<br />
3-3/4 110186 110536 20<br />
4 03046 04046 20<br />
4-1/2 03047 04047 10<br />
5 03048 04048 10<br />
5-1/2 03049 04049 10<br />
6 03050 04050 10<br />
Hex Nut 110823 110850 100<br />
Nylon Insert<br />
Locknut<br />
05062 05072 50<br />
Flatwasher 05118 05128 150<br />
Lockwasher 05138 05138 150<br />
1 800 458-4018 www.uzengprod.com<br />
USS (NC) SAE (NF)<br />
LENGTH<br />
1/2<br />
5/8<br />
PART # PART # QTY.<br />
3/4<br />
7/8<br />
03051 04051 75<br />
1 03052 04052 75<br />
1-1/4 03053 04053 75<br />
1-1/2 03054 04054 50<br />
1-3/4 03055 04055 25<br />
2 03056 04056 25<br />
2-1/4 03057 04057 25<br />
2-1/2 03058 04058 25<br />
2-3/4 03059 04059 20<br />
3 03060 04060 20<br />
3-1/4 110217 110567 20<br />
3-1/2 03061 04061 20<br />
3-3/4 110219 110569 20<br />
4 03062 04062 10<br />
4-1/2 03063 04063 10<br />
5 03064 04064 10<br />
5-1/2 03065 04065 10<br />
6 03066 04066 10<br />
Hex Nut 110824 110851 50<br />
Nylon Insert 05063<br />
Locknut<br />
05073 50<br />
Flatwasher 05119 05129 75<br />
Lockwasher 05139 05139 100
Grade 5 Cap Screws<br />
Tensile Strength 120,000 PSI Minimum<br />
1/2" Diameter 9/16" Diameter<br />
Grade 5 <strong>Fasteners</strong><br />
THREAD PITCH: USS 1/2-13 SAE 1/2-20 THREAD PITCH: USS 9/16-12 SAE 9/16-18<br />
WIDTH ACROSS FLATS: 3/4" WIDTH ACROSS FLATS: 13/16"<br />
HEAD HEIGHT (MAX): 5/16 HEAD HEIGHT (MAX): 23/64<br />
USS (NC) SAE (NF) USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY. LENGTH PART # PART # QTY.<br />
1/2 1 03095 04095 10<br />
5/8 1-1/4 03096 04096 10<br />
3/4 03067 04067 25 1-1/2 03097 04097 10<br />
7/8 1-3/4 03098 04098 10<br />
1 03068 04068 25 2 03099 04099 10<br />
1-1/4 03069 04069 25 2-1/4 03100 04100 10<br />
1-1/2 03070 04070 25 2-1/2 03101 04101 5<br />
1-3/4 03071 04071 25 2-3/4 03102 04102 5<br />
2 03072 04072 25 3 03103 04103 5<br />
2-1/4 03073 04073 20 3-1/4 110281 110631 5<br />
2-1/2 03074 04074 20 3-1/2 03104 04104 5<br />
2-3/4 03075 04075 20 3-3/4 110283 110633 5<br />
3 03076 04076 20 4 03105 04105 5<br />
3-1/4 110250 110600 10 4-1/2 03106 04106 5<br />
3-1/2 03077 04077 10 5 03107 04107 5<br />
3-3/4 110252 110602 10 5-1/2 03108 04108 5<br />
4 03078 04078 10 6 03109 04109 5<br />
4-1/2 03079 04079 10<br />
Hex Nut 110826 110853 25<br />
5<br />
5-1/2<br />
6<br />
7<br />
03080<br />
03081<br />
03082<br />
03084<br />
04080<br />
04081<br />
04082<br />
10<br />
10<br />
10<br />
5<br />
Nylon Insert 05065<br />
Locknut<br />
Flatwasher 05121<br />
Lockwasher 05141<br />
05075<br />
05131<br />
05141<br />
25<br />
50<br />
50<br />
Hex Nut 110825 110852 50<br />
Nylon Insert 05064<br />
Locknut<br />
05074 25<br />
Flatwasher 05120 05130 75<br />
Lockwasher 05140 05140 75<br />
1 800 458-4018 www.uzengprod.com<br />
111<br />
FASTENERS
FASTENERS<br />
112<br />
Grade 5 <strong>Fasteners</strong><br />
Grade 5 Cap Screws<br />
Tensile Strength 120,000 PSI Minimum<br />
5/8" Diameter 3/4" Diameter<br />
THREAD PITCH: USS 5/8-11 SAE 5/8-18 THREAD PITCH: USS 3/4-10 SAE 3/4-16<br />
WIDTH ACROSS FLATS: 15/16" WIDTH ACROSS FLATS: 1-1/8"<br />
HEAD HEIGHT (MAX): 25/64 HEAD HEIGHT (MAX): 15/32<br />
USS (NC) SAE (NF) USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY. LENGTH PART # PART # QTY.<br />
1 03122 04122 20 1 110334 110684 10<br />
1-1/4 03123 04123 20 1-1/4 110335 110685 10<br />
1-1/2 03124 04124 20 1-1/2 03149 04149 10<br />
1-3/4 03125 04125 20 1-3/4 03150 04150 10<br />
2 03126 04126 20 2 03151 04151 10<br />
2-1/4 03127 04127 10 2-1/4 03152 04152 10<br />
2-1/2 03128 04128 10 2-1/2 03153 04153 10<br />
2-3/4 03129 04129 10 2-3/4 03154 04154 10<br />
3 03130 04130 10 3 03155 04155 10<br />
3-1/4 110312 110662 10 3-1/4 110343 110693 5<br />
3-1/2 03131 04131 10 3-1/2 03156 04156 5<br />
3-3/4 110314 110664 10 3-3/4 110345 110695 5<br />
4 03132 04132 10 4 03157 04157 5<br />
4-1/2 03133 04133 10 4-1/2 03158 04158 5<br />
5 03134 04134 5 5 03159 04159 5<br />
5-1/2 03135 04135 5 5-1/2 03160 04160 5<br />
6 03136 04136 5 6 03161 04161 5<br />
7 03138 5 6-1/2 03162 2<br />
10 03144 2 7 03163 2<br />
Hex Nut 110827 110854 25<br />
Nylon Insert 05066 05076 25<br />
Locknut<br />
Flatwasher 05122 05132 50<br />
Lockwasher 05142 05142 50<br />
1 800 458-4018 www.uzengprod.com<br />
8 03165 2<br />
10 03169 2<br />
Hex Nut 110828 110855 10<br />
Nylon Insert 05067<br />
Locknut<br />
05077 25<br />
Flatwasher 05123 05133 25<br />
Lockwasher 05143 05143 25
Grade 5 Cap Screws<br />
Tensile Strength 120,000 PSI Minimum<br />
7/8" Diameter 1" Diameter<br />
THREAD PITCH: USS 7/8-9 SAE 7/8-14 THREAD PITCH: USS 1-8 SAE 1-14<br />
WIDTH ACROSS FLATS: 1-5/16" WIDTH ACROSS FLATS: 1-1/2"<br />
HEAD HEIGHT (MAX): 35/64 THREAD HEIGHT (MAX): 39/64<br />
Grade 5 <strong>Fasteners</strong><br />
USS (NC) SAE (NF) USS (NC) SAE (NF)<br />
LENGTH PART # PART # QTY. LENGTH PART # PART # QTY.<br />
1-1/2 110365 110715 10 1-1/2 110394 5<br />
1-3/4 110366 110716 10 1-3/4 110395 110745 5<br />
2 03174 04174 10 2 03195 04195 5<br />
2-1/4 110368 110718 10 2-1/4 110397 110747 5<br />
2-1/2 03175 04175 5 2-1/2 03196 04196 5<br />
2-3/4 110370 110720 5 2-3/4 110399 110749 5<br />
3 03176 04176 5 3 03197 04197 5<br />
3-1/4 110372 110722 5 3-1/4 110401 110751 5<br />
3-1/2 03177 04177 5 3-1/2 03198 04198 5<br />
3-3/4 110374 110724 5 3-3/4 110403 110753 5<br />
4 03178 04178 5 4 03199 04199 5<br />
4-1/2 03179 04179 5 4-1/2 03200 04200 5<br />
5 03180 04180 5 5 03201 04201 5<br />
5-1/2 03181 04181 5 5-1/2 03202 04202 5<br />
6 03182 04182 5 6 03203 04203 5<br />
Hex Nut 110829 110856 10<br />
Hex Nut 110830 110857 10<br />
Nylon Insert 05068<br />
Locknut<br />
05078 25<br />
Flatwasher 05124 05134 20<br />
Lockwasher 05144 05144 20<br />
Nylon Insert 05069<br />
Locknut<br />
05079 25<br />
Flatwasher 05125 05135 20<br />
Lockwasher 05145 05145 20<br />
1 800 458-4018 www.uzengprod.com<br />
113<br />
FASTENERS
FASTENERS<br />
114<br />
Serrated Hex Flange Screws<br />
Serrated Hex Flange Screws<br />
• Designed for use in applications where loosening forces are present, such as vibration.<br />
• The serrations grip the bearing surface so that more torque is needed to loosen than tighten the screw.<br />
• The serrated flange provides more strength than the standard machine screw.<br />
• Grade 5 material per SAE J429 (1999)<br />
• Tensile strength is 120,000 PSI<br />
• Screws have a Class 2A thread fit and are fully threaded<br />
• Zinc plated for rust resistance<br />
SCREW<br />
DIA<br />
#10<br />
1/4<br />
5/16<br />
3/8<br />
1/2<br />
LGTH<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
SERRATED HEX<br />
FLANGE NUT<br />
F<br />
WIDTH ACROSS<br />
FLATS<br />
MAX MIN<br />
0.312 0.305<br />
0.375 0.367<br />
0.500 0.489<br />
0.562 0.551<br />
0.750 0.736<br />
10-24<br />
PART # QTY<br />
121481 100<br />
121482 100<br />
121483 100<br />
121484 100<br />
121485 100<br />
07384<br />
G<br />
WIDTH ACROSS<br />
CORNERS<br />
MAX MIN<br />
0.368 0.340<br />
0.433 0.409<br />
0.577 0.548<br />
0.650 0.618<br />
0.866 0.825<br />
10-32<br />
PART # QTY<br />
121486 100<br />
121487 100<br />
121488 100<br />
121489 100<br />
121490 100<br />
1 800 458-4018 www.uzengprod.com<br />
B<br />
FLANGE<br />
DIA<br />
MAX<br />
0.454<br />
0.56<br />
0.68<br />
0.81<br />
1.07<br />
H<br />
HEIGHT OF<br />
HEAD<br />
MAX<br />
0.209<br />
0.28<br />
0.32<br />
0.39<br />
0.51<br />
1/4-20<br />
PART # QTY<br />
121491 100<br />
121492 100<br />
121493 100<br />
121494 100<br />
121495 100<br />
121496 50<br />
121497 50<br />
121498 50<br />
121499 50<br />
121500 50<br />
121501 50<br />
121502 50<br />
121503 50<br />
121504 50<br />
07385<br />
DIAMETER<br />
U<br />
FLANGE<br />
THICKNESS<br />
MIN<br />
0.031<br />
0.04<br />
0.05<br />
0.06<br />
0.08<br />
5/16-18<br />
PART # QTY<br />
121505 50<br />
121506 50<br />
121507 50<br />
121508 50<br />
121509 50<br />
121510 50<br />
121511 50<br />
121512 50<br />
121513 50<br />
121514 50<br />
121515 50<br />
121528 25<br />
121529 25<br />
07386<br />
K<br />
WRENCH<br />
HEIGHT<br />
MIN<br />
0.134<br />
0.17<br />
0.21<br />
0.25<br />
0.34<br />
3/8-16<br />
PART # QTY<br />
121516 50<br />
121517 50<br />
121518 50<br />
121519 50<br />
121520 50<br />
121521 50<br />
121522 50<br />
121523 50<br />
121524 50<br />
121526 50<br />
121527 50<br />
121528 25<br />
121529<br />
07388<br />
25<br />
Available in Assortment<br />
Part #00996 found on page 40<br />
B1<br />
SERRATED<br />
DEPTH<br />
MIN<br />
0.009<br />
0.011<br />
0.013<br />
0.015<br />
0.019<br />
R1<br />
FILLET<br />
MIN<br />
0.011<br />
0.015<br />
0.015<br />
0.015<br />
0.015<br />
1/2-13<br />
PART # QTY<br />
121532 25<br />
121533 25<br />
121534 25<br />
121535 25<br />
121536 25<br />
121537 25<br />
121538 25<br />
121539 25<br />
121540 25<br />
121541 25
Free Spinning Flange Lock Nut<br />
With Uni-Guard Coating<br />
The latest innovation in locking nuts!<br />
FREE Spinning installation eliminates the need to "wrench" the nut down<br />
the thread.<br />
Uni-Guard Coating provides superior protection from corrosion.<br />
Product Features<br />
• Grade 8 strength and quality, but will work with any grade of fastener including high<br />
strength fasteners.<br />
• Does not damage threads or plating on fasteners<br />
• Locks to the part - not to the threads<br />
• Exceptional performance in applications with heavy vibration<br />
• Greater temperature range than nylon insert locknuts<br />
• Hardness of 28-38 HRc - More effective at maintaining clamp load under vibration<br />
• Not limited to 5 reuses, as with most other torque lock nuts<br />
PART # SIZE PKG QTY A B C<br />
113909UG 1/4-20 20 7/16 19/32 1/4<br />
113910UG 5/16-18 20 1/2 11/16 9/32<br />
113911UG 3/8-16 15 9/16 3/4 11/32<br />
113912UG 7/16-14 10 11/16 15/16 3/8<br />
113913UG 1/2-13 5 3/4 1 7/16<br />
113914UG 5/8-11 5 15/16 1-1/4 9/16<br />
Available in<br />
an Assortment<br />
PART #00495<br />
Found on Page 40<br />
PART # 00496KP<br />
Found on Page 40<br />
Standard Nut Fastener<br />
1 800 458-4018 www.uzengprod.com<br />
115<br />
FASTENERS
FASTENERS<br />
116<br />
Standard Nut <strong>Fasteners</strong><br />
Finished Hex Nuts<br />
• Conforms to SAE J995 and • Uni-zinc plated to resist rust and corrosion.<br />
MIL Spec MIL DTL-1222J. • Washer faced for full seating<br />
• For use with Grade 5 Cap Screws. • Clean burr-free threads for easier seating.<br />
• Full finished dimensions. • Full chamfered for positive wrenching.<br />
USS(NC) SAE(NF) WIDTH<br />
ACROSS THICKNESS QTY.<br />
BOLT SIZE PART # SIZE PART # SIZE FLATS<br />
1/4 110821 1/4-20 110848 1/4-28 7/16 7/32 100<br />
5/16 110822 5/16-18 110849 5/16-24 1/2 17/64 100<br />
3/8 110823 3/8-16 110850 3/8-24 9/16 21/64 100<br />
7/16 110824 7/16-14 110851 7/16-20 11/16 3/8 50<br />
1/2 110825 1/2-13 110852 1/2-20 3/4 7/16 50<br />
9/16 110826 9/16-12 110853 9/16-18 7/8 31/64 25<br />
5/8 110827 5/8-11 110854 5/8-18 15/16 35/64 25<br />
3/4 110828 3/4-10 110855 3/4-16 1-1/8 41/64 10<br />
7/8 110829 7/8-9 110856 7/8-14 1-5/16 3/4 10<br />
1 110830 1-8 110857 1-14 1-1/2 55/64 10<br />
1-1/8 110831 1-1/8-7 110858 1-1/8-12 1-11/16 31/32 2<br />
1-1/4 110832 1-1/4-7 110859 1-1/4-12 1-7/8 1-1/16 2<br />
1-1/2 110833 1-1/2-6 110860 1-1/2-12 2-1/4 1-9/32 2<br />
Hex Jam Nuts<br />
• Made from SAE approved carbon steel.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
USS (NC) SAE (NF) WIDTH<br />
ACROSS THICKNESS QTY.<br />
PART # SIZE PART # SIZE FLATS<br />
05080 1/4-20 05090 1/4-28 7/16 5/32 100<br />
05081 5/16-18 05091 5/16-24 1/2 3/16 100<br />
05082 3/8-16 05092 3/8-24 9/16 7/32 100<br />
05083 7/16-14 05093 7/16-20 11/16 1/4 100<br />
05084 1/2-13 05094 1/2-20 3/4 5/16 100<br />
05085 9/16-12 05095 9/16-18 7/8 5/16 50<br />
05086 5/8-11 05096 5/8-18 15/16 3/8 50<br />
05087 3/4-10 05097 3/4-16 1-1/8 27/64 25<br />
05088 7/8-9 05098 7/8-14 1-5/16 31/64 25<br />
05089 1-8 05099 1-14 1-1/2 35/64 25<br />
05646 1-1/8-7 05649 1-1/8-12 1-11/16 39/64 10<br />
05647 1-1/4-7 05650 1-1/4-12 1-7/8 23/32 10<br />
05648 1-1/2-6 05651 1-1/2-12 2-1/4 27/32 10<br />
1 800 458-4018 www.uzengprod.com
Miscellaneous Nuts<br />
Hex Machine Screw Nuts<br />
• Double chamfered.<br />
• Sharp corners for easier wrenching.<br />
• Uni-zinc plated.<br />
PART # SIZE<br />
WIDTH<br />
ACROSS THICKNESS<br />
FLATS<br />
QTY.<br />
05109 4-40 1/4 3/32 200<br />
05110 6-32 5/16 7/64 200<br />
05111 8-32 11/32 1/8 200<br />
05112 10-24 3/8 1/8 200<br />
05113 10-32 3/8 1/8 200<br />
07435 12-24 7/16 9/64 200<br />
05114 1/4-20 7/16 3/16 200<br />
07436 1/4-28 7/16 3/16 100<br />
05115 5/16-18 9/16 7/32 200<br />
110810 3/8-16 5/8 1/4 100<br />
SAE High Nuts<br />
• Extra thick-provides more thread engagement.<br />
• Uni-zinc plated.<br />
• Most sizes made from alloy steel.<br />
PART # SIZE<br />
WIDTH<br />
MATERIAL ACROSS THICKNESS QTY.<br />
FLATS<br />
116724 1/2-20 Low Carbon 3/4 11/16 25<br />
116727 5/8-18 Alloy 15/16 27/32 25<br />
116728 3/4-16 Alloy 1-1/16 1 25<br />
116729 3/4-16 Alloy 1-1/8 1 25<br />
116730 7/8-14 Alloy 1-1/4 1-5/32 10<br />
116731 7/8-14 Alloy 1-5/16 1-5/32 10<br />
116732 1-14 Alloy 1-7/16 1-5/16 10<br />
116733 1-14 Alloy 1-1/2 1-5/16 10<br />
Standard Nut <strong>Fasteners</strong><br />
Heavy Hex Nuts-Grade 2<br />
• Thicker than hex nuts finished.<br />
• Uni-zinc plated.<br />
PART # SIZE<br />
WIDTH<br />
ACROSS THICKNESS<br />
FLATS<br />
QTY.<br />
110834 1/4-20 1/2 15/64 100<br />
110835 5/16-18 9/16 19/64 100<br />
110836 3/8-16 11/16 23/64 100<br />
110837 7/16-14 3/4 27/64 100<br />
110838 1/2-13 7/8 31/64 100<br />
110840 5/8-11 1-1/16 39/64 50<br />
110841 3/4-10 1-1/4 47/64 25<br />
110842 7/8-9 1-7/16 55/64 10<br />
110843 1-8 1-5/8 63/64 10<br />
Finished Hex<br />
Castle Nuts<br />
• Uni-zinc plated.<br />
• Provides access for a cotter<br />
pin after nut is seated.<br />
PART # SIZE<br />
WIDTH<br />
ACROSS<br />
FLATS<br />
THICKNESS QTY.<br />
116290 1/4-28 7/16 9/32 50<br />
116291 5/16/24 1/2 21/64 50<br />
116292 3/8-24 9/16 13/32 50<br />
116293 7/16-20 11/16 29/64 50<br />
116294 1/2-20 3/4 9/16 50<br />
116295 5/8-18 15/16 23/32 25<br />
116296 3/4-16 1-1/8 13/16 25<br />
116297 7/8-14 1-5/16 29/32 10<br />
116299 1-1/4-12 1-7/8 1-1/4 10<br />
1 800 458-4018 www.uzengprod.com<br />
117<br />
FASTENERS
FASTENERS<br />
118<br />
Standard Nut <strong>Fasteners</strong><br />
Miscellaneous Nuts<br />
Acorn Nuts<br />
• Nickel plated for decorative chrome look.<br />
• Covers end of fastener for safety.<br />
PART # SIZE<br />
WRENCH<br />
SIZE QTY.<br />
07363 6-32 5/16 50<br />
07364 8-32 5/16 50<br />
07365 10-24 11/32 50<br />
07366 10-32 11/32 50<br />
07367 1/4-20 7/16 50<br />
07368 5/16-18 17/32 50<br />
07369 3/8-16 19/32 25<br />
07370 1/2-13 3/4 25<br />
07371 5/8-11 15/16 10<br />
Pal Nuts-Washer Locknuts<br />
• Uni-zinc plated to resist rust and corrosion.<br />
• Economical.<br />
• For light duty applications.<br />
OUTSIDE WRENCH<br />
PART # SIZE DIAMETER SIZE QTY.<br />
07391 6-32 7/16 5/16 50<br />
07392 8-32 15/32 11/32 50<br />
07393 10-32 1/2 3/8 50<br />
07394 10-24 1/2 3/8 50<br />
07395 10-24 3/4 3/8 50<br />
07396 12-24 3/4 3/8 50<br />
07397 1/4-20 19/32 7/16 50<br />
07398 1/4-20 13/16 7/16 50<br />
07399 5/16-18 13/16 1/2 25<br />
1 800 458-4018 www.uzengprod.com<br />
Keps Nuts<br />
• Uni-zinc plated to resist rust and corrosion.<br />
• Permanently attached to lockwasher.<br />
• Resists loosening due to vibration.<br />
PART # SIZE<br />
WRENCH<br />
SIZE QTY.<br />
07372 4-40 1/4 50<br />
07373 6-32 5/16 50<br />
07374 8-32 11/32 50<br />
07375 10-24 3/8 50<br />
07376 10-32 3/8 50<br />
07377 1/4-20 7/16 50<br />
07378 1/4-28 7/16 50<br />
07379 5/16-18 1/2 25<br />
07380 5/16-24 1/2 25<br />
07381 3/8-16 9/16 25<br />
07382 3/8-24 9/16 25<br />
Serrated Hex Flange Nuts<br />
• Uni-zinc plated to resist rust and corrosion.<br />
• No separate washer required.<br />
• Serrated washer face.<br />
• Resists loosening due to vibration.<br />
PART # SIZE<br />
WRENCH<br />
SIZE QTY.<br />
07383 8-32 13/32 25<br />
07384 10-24 1/2 25<br />
07385 1/4-20 19/32 25<br />
07386 5/16-18 21/32 25<br />
07387 5/16-24 21/32 25<br />
07388 3/8-16 3/4 25<br />
07389 3/8-24 3/4 25<br />
07390 7/16-14 29/32 25
Miscellaneous Nuts<br />
Cold Forged<br />
Type "A" Wing Nuts<br />
• Made from solid SAE approved steel.<br />
• Cold formed for greater strength and endurance.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
PART # SIZE QTY.<br />
07437 4-40 25<br />
05100 6-32 25<br />
05101 8-32 25<br />
05102 10-24 25<br />
05103 10-32 25<br />
07438 12-24 25<br />
05104 1/4-20 25<br />
07439 1/4-28 25<br />
05105 5/16-18 25<br />
05106 3/8-16 25<br />
05107 7/16-14 10<br />
05108 1/2-13 10<br />
Available in<br />
an Assortment<br />
PART # 00715<br />
Found on Page 41<br />
Automotive Series Hex Nuts<br />
• Difficult to find.<br />
• Preferred by most mechanics.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
PART # SIZE<br />
ACROSS THE<br />
FLATS QTY.<br />
210309 7/16-14 5/8 100<br />
210310 7/16-20 5/8 100<br />
Standard Nut <strong>Fasteners</strong><br />
Hex Coupling Nuts<br />
• Zinc plated.<br />
• Super thick.<br />
• Often used to connect threaded rods.<br />
PART # SIZE LENGTH QTY.<br />
116280 10-24 7/8 25<br />
116281 1/4-20 7/8 25<br />
116282 5/16-18 1-1/8 25<br />
116283 3/8-16 1-1/8 25<br />
116284 1/2-13 1-1/4 25<br />
116285 5/8-11 2-1/8 10<br />
116286 3/4-10 2-1/4 10<br />
Tee Nuts-3 Prong<br />
• Long prong type, internally threaded.<br />
• For use in wood.<br />
• Uni-zinc plated.<br />
PART # SIZE<br />
OUTSIDE<br />
DIA. HEIGHT QTY.<br />
116060 8-32 3/4 1/4 50<br />
116061 10-24 3/4 9/32 50<br />
116062 10-32 3/4 5/16 50<br />
116063 1/4-20 3/4 7/16 50<br />
116064 5/16-18 7/8 3/8 50<br />
116065 3/8-16 1 7/16 25<br />
1 800 458-4018 www.uzengprod.com<br />
119<br />
FASTENERS
FASTENERS<br />
120<br />
Specialty Nut <strong>Fasteners</strong><br />
Heavy 2-H Full Hex Nuts<br />
• Heat treated for greater strength.<br />
• Heavy hex nut dimensions.<br />
• Black finish.<br />
Look for the 2H...<br />
It's your guarantee that you're getting the strength required!<br />
2H nuts are designed to be used with B-7 alloy studs and threaded rod. When used in<br />
high temperature applications, an assembly consisting of B7 rod or studs and 2H nuts<br />
will withstand constant temperatures of up to 1100°F.<br />
PART DIMENSIONS<br />
SIZE # QTY. THICKNESS ACROSS FLATS<br />
3/8-16 272350 50 23/64 11/16<br />
1/2-13 272351 50 31/64 7/8<br />
5/8-11 272352 25 39/64 1-1/16<br />
3/4-10 272353 25 47/64 1-1/4<br />
7/8-9 272354 10 55/64 1-7/16<br />
1-8 272355 10 63/34 1-5/8<br />
Nylon Insert Lock Nuts<br />
(Elastic Stop Nuts)<br />
• Keeps fastener assemblies tight even when vibration is present.<br />
• Use with Grade 5 Cap Screws and machine screws.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
USS (NC) SAE (NF) WIDTH<br />
ACROSS THICKNESS QTY.<br />
PART # SIZE PART # SIZE FLATS<br />
07426 4-40 1/4 5/32 100<br />
07427 6-32 5/16 11/64 100<br />
07428 8-32 11/32 7/32 100<br />
07429 10-24 07430 10-32 3/8 15/64 100<br />
07431 12-24 7/16 5/16 100<br />
05060 1/4-20 05070 1/4-28 7/16 5/16 50<br />
05061 5/16-18 05071 5/16-24 1/2 11/32 50<br />
05062 3/8-16 05072 3/8-24 9/16 29/64 50<br />
05063 7/16-14 05073 7/16-20 5/8 29/64 50<br />
05064 1/2-13 05074 1/2-20 3/4 19/32 25<br />
05065 9/16-12 05075 9/16-18 7/8 21/32 25<br />
05066 5/8-11 05076 5/8-18 15/16 3/4 25<br />
05067 3/4-10 05077 3/4-16 1-1/16 7/8 25<br />
05068 7/8-9 05078 7/8-14 1-1/8 63/64 25<br />
05069 1-8 05079 1-14 1-7/16 1-3/64 25<br />
05640 1-1/8-7 05643 1-1/8-12 1-11/16 1-9/32 10<br />
05641 1-1/4-7 05644 1-1/4-12 1-7/8 1-27/64 10<br />
05642 1-1/2-6 05645 1-1/2-12 2-1/4 1-43/64 10<br />
1 800 458-4018 www.uzengprod.com<br />
• Recommended for use in high temperature applications.<br />
• Conforms to ASTM 194-2H specifications.<br />
• Meets MIL Spec MIL DTL-1222J.<br />
Available in<br />
an Assortment & Kwik Pak<br />
PART # 00825<br />
Found on Page 41<br />
PART # 00825KP<br />
Found on Page 41
Hex Jam Nuts with Nylon Insert<br />
NTE Series<br />
SAE Spec 122, ANSI/ASME B18.2.2<br />
Grade 2, Class 2B threads<br />
Zinc Plated<br />
Standard Nut <strong>Fasteners</strong><br />
Size USS Size SAE Qty Height Across Across Wrench<br />
Flats Corners Pad<br />
1/4-20 109880 1/4-28 109890 100 0.023 .439-.430 0.482 0.125<br />
5/16-18 109881 5/16-24 109891 100 0.250 .502-.492 0.552 0.158<br />
3/8-16 109882 3/8-1624 109892 100 0.266 .564-.553 0.622 0.150<br />
7/16-14 109883 7/16-20 109893 75 0.313 .627-.615 0.694 0.225<br />
1/2-13 109884 1/2-20 109894 50 0.313 .752-.741 0.837 0.190<br />
9/16-12 109885 9/16-18 109895 10 0.359 .877-.865 0.978 0.225<br />
5/8-11 109886 5/8-18 109896 10 0.391 .940-.928 1.051 0.265<br />
3/4-10 109887 3/4-16 109897 10 0.406 1.064-1.052 1.191 0.288<br />
7/8-9 109888 7/8-14 109898 5 0.469 1.252-1.239 1.403 0.340<br />
1-8 109889 1-14 109899 5 0.547 1.440-1.427 1.615 0.405<br />
1-1/8-7 109900 1-1/8-12 109901 1 0.641 1.627-1.614 1.826 0.500<br />
1-1/4-7 109902 1-1/4-12 109903 1 0.734 1.814-1.801 2.038 0.523<br />
1-3/8-6 109904 1-3/8-12 109905 1 0.790 2.008-1.973 2.249 0.493<br />
1-1/2-6 109906 1-1/2-12 109907 1 0.797 2.197-2.159 2.416 0.565<br />
1 800 458-4018 www.uzengprod.com<br />
121<br />
FASTENERS
FASTENERS<br />
122<br />
Standard Nut <strong>Fasteners</strong><br />
Heavy Hex Nuts - Thin Height with Nylon Insert<br />
NTU Series, Zinc plated<br />
USS<br />
Size Part # Qty Height Across Across Wrench<br />
Flats Corners Pad<br />
1/4-20 110342 100 0.281 .502-.492 0.552 0.194<br />
5/16-18 110344 100 0.313 .564-.553 0.622 0.212<br />
3/8-16 110346 75 0.406 .690-.679 0.766 0.251<br />
7/16-14 110347 25 0.438 .752-.741 0.837 0.316<br />
1/2-13 110348 25 0.531 .877-.865 0.978 0.360<br />
5/8-11 110349 15 0.609 1.064-1.052 1.191 0.428<br />
3/4-10 110350 10 0.703 1.252-1.239 1.403 0.488<br />
7/8-9 110351 5 0.781 1.440-1.427 1.615 0.535<br />
1-8 110352 1 0.891 1.627-1.614 1.826 0.600<br />
1-1/8-7 110353 1 0.969 1.814-1.801 2.038 0.627<br />
1-1/4-7 110354 1 1.109 2.008-1.973 2.232 0.720<br />
1-3/8-6 110355 1 1.188 2.197-2.159 2.444 0.767<br />
1-1/2-6 110356 1 1.313 2.384-2.344 2.622 0.810<br />
Heavy Hex Lock Nuts with Nylon Insert<br />
NU Series, Zinc Plated<br />
USS<br />
Size Part # Qty Height Across Across Wrench<br />
Flats Corners Pad<br />
1/4-20 110119 100 0.375 .503-.489 0.556 0.290<br />
5/16-18 110120 100 0.438 .566-.551 0.624 0.335<br />
3/8-16 110121 75 0.547 .691-.675 0.763 0.392<br />
7/16-14 110122 25 0.594 .754-.736 0.829 0.464<br />
1/2-13 110123 25 0.703 .879-.861 0.969 0.544<br />
5/8-11 110124 15 0.859 1.067-1.045 1.175 0.677<br />
3/4-10 110125 10 1 1.255-1.231 1.382 0.790<br />
7/8-9 110193 5 1.125 1.444-1.417 1.589 0.883<br />
1-8 110126 1 1.281 1.632-1.602 1.796 1.000<br />
1-1/8-7 110127 1 1.438 1.820-1.788 2.002 1.096<br />
1-1/4-7 110128 1 1.641 2.008-1.973 2.209 1.250<br />
1-3/8-6 110129* 1 1.797 2.192-2.159 2.416 1.376<br />
1-1/2-6 110130* 1 1.922 2.384-2.344 2.622 1.413<br />
*NOT PLATED<br />
1 800 458-4018 www.uzengprod.com
Flatwashers (USS & SAE)<br />
• Use with Grade 5 Cap Screws and machine screws.<br />
• Precision stamped from prime SAE approved carbon steel.<br />
• Consistent uniform thickness.<br />
USS SIZES<br />
For use in normal applications. The thicker wall provides<br />
maximum bearing surface for a more even distribution of<br />
the load and greater resistance to pull through.<br />
USS<br />
PART #<br />
BOLT<br />
SIZE I.D. O.D. THICKNESS QTY.<br />
110875 3/16(#10) 1/4 9/16 3/64 500<br />
05116 1/4 5/16 3/4 1/16 200<br />
05117 5/16 3/8 7/8 5/64 200<br />
05118 3/8 7/16 1 5/64 150<br />
05119 7/16 1/2 1-1/4 5/64 75<br />
05120 1/2 9/16 1-3/8 7/64 75<br />
05121 9/16 5/8 1-1/2 7/64 50<br />
05122 5/8 11/16 1-3/4 9/64 50<br />
05123 3/4 13/16 2 5/32 25<br />
05124 7/8 15/16 2-1/4 11/64 20<br />
05125 1 1-1/16 2-1/2 11/64 20<br />
05600 1-1/8 1-1/4 2-3/4 11/64 5<br />
05601 1-1/4 1-3/8 3 11/64 5<br />
05602 1-1/2 1-5/8 3-1/2 3/16 5<br />
• Use with Grade 5 Cap Screws and machine screws.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
• Smooth, burr-free surfaces.<br />
• Provides a larger bearing surface to distribute load evenly.<br />
SAE SIZES<br />
For application where space is limited or appearance is a factor.<br />
The thinner wall provides adequate bearing surface closer inside<br />
diameter tolerance than USS washers on sizes through 5/8".<br />
SAE<br />
Oversized (Fender) Washers Plated - Extra Thick<br />
• Provides more "bearing surface" than standard washers<br />
• Use wherever fastener "pull through" is a problem.<br />
• Extra thickness provides the additional spacing<br />
without the addition of more washers<br />
PART # BOLT SIZE I.D. O.D. THICKNESS QTY<br />
123448 #10 (3/16) 7/32 15/16 .108/.132 50<br />
07419 #10(3/16) 7/32 1 .051/.080 100<br />
07420 #10 (3/16) 7/32 1-1/4 .051/.080 100<br />
113902 1/4 9/32 1 .051/.080 100<br />
123449 1/4 9/32 1 .108/.132 50<br />
123450 1/4 9/32 1-1/8 .108/.132 50<br />
07421 1/4 9/32 1-1/4 .050/.080 100<br />
07422 1/4 9/32 1-1/2 .050/.080 100<br />
Standard Washers<br />
PART #<br />
BOLT<br />
SIZE I.D. O.D. THICKNESS QTY.<br />
07400 #4 1/8 5/16 1/32 250<br />
07401 #6 5/32 3/8 3/64 250<br />
07402 #8 3/16 7/16 3/64 250<br />
07403 #10(3/16) 7/32 1/2 3/64 200<br />
07404 #12 1/4 9/16 1/16 200<br />
05126 1/4 9/32 5/8 1/16 200<br />
05127 5/16 11/32 11/16 1/16 200<br />
05128 3/8 13/32 13/16 1/16 150<br />
05129 7/16 15/32 59/64 1/16 75<br />
05130 1/2 17/32 1-1/16 3/32 75<br />
05131 9/16 19/32 13/16 3/32 50<br />
05132 5/8 21/32 1-5/16 3/32 50<br />
05133 3/4 13/16 1-1/2 9/64 25<br />
05134 7/8 15/16 1-3/4 9/64 20<br />
05135 1 1-1/16 2 9/64 20<br />
05603 1-1/8 1-3/16 2-1/4 9/64 5<br />
05604 1-1/4 1-5/16 2-1/2 5/32 5<br />
05605 1-1/2 1-9/16 3 5/32 5<br />
Oversize washers are ideal in applications where is is<br />
necessary to clamp thin materials. The larger bearing<br />
surface allows you to make the assembly tighter<br />
without “pull through” for greater protection against<br />
fastener failure.<br />
PART # BOLT SIZE I.D. O.D. THICKNESS QTY<br />
123451 1/4 9/32 1-1/2 .108/.132 50<br />
07423 5/16 11/32 1-1/4 .051/.080 100<br />
123452 5/16 11/32 1-1/4 .108/.132 50<br />
07424 5/16 11/32 1-1/2 .051/.080 100<br />
123453 3/8 7/16 1-1/4 .108/.132 50<br />
07425 3/8 13/32 1-1/2 .051/.080 100<br />
123454 3/8 7/16 1-3/4 .108/.132 50<br />
113908 1/2 17/32 2 .051/.080 100<br />
123455 1/2 17/32 2 .108/.132 50<br />
1 800 458-4018 www.uzengprod.com<br />
123<br />
FASTENERS
FASTENERS<br />
124<br />
Standard Washers<br />
Tru Lock Washers<br />
• Self Locking, through hardened steel washers that mate together<br />
• The back sides have ridges that bite into the joined material, nut or capscrew<br />
• Through Hardened Min 44HRC, Max 51 HRC<br />
• Zinc Yellow Chromate Finish<br />
• Ease of assembly and disasssembly<br />
• Locking function not affected by lubrication<br />
• Use with USS, SAE and Metric Capscrews - All Grades<br />
INSIDE DIAMETER Pk Qty<br />
Inch Sizes Metric Sizes Part # Pairs<br />
#10 M5 107300 20<br />
na M6 107301 20<br />
1/4 na 107302 20<br />
5/16 M8 107303 20<br />
na M10 107304 20<br />
3/8 na 107305 20<br />
7/16 M11 107307 10<br />
na M12 107308 10<br />
1/2 na 107309 10<br />
9/16 M14 107311 10<br />
5/8 M16 107313 10<br />
11/16 M18 107315 10<br />
na M20 107316 10<br />
3/4 na 107317 10<br />
7/8 M22 107319 5<br />
15/16 M24 107321 5<br />
1 na 107322 5<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00430<br />
Found on Page 43
Spring Lockwashers<br />
• For use with Grade 5 Cap Screws & machine screws. • Will not warp or lose tension.<br />
• Helps prevent loose bolt problems and assembly failures. • Made from tempered spring steel.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
Directions of tension<br />
provided by lockwasher<br />
in application<br />
Top edge creates<br />
tension upward<br />
Bottom edge creates<br />
tension downward<br />
BOLT BOLT<br />
PART # SIZE QTY. PART # SIZE QTY.<br />
07405 #4 250 05140 1/2 75<br />
07406 #6 250 05141 9/16 50<br />
07407 #8 250 05142 5/8 50<br />
05146 #10 200 05143 3/4 25<br />
07408 #12 200 05144 7/8 20<br />
05136 1/4 200 05145 1 20<br />
05137 5/16 150 05607 1-1/8 5<br />
05138 3/8 150 05608 1-1/4 5<br />
05139 7/16 100 05609 1-1/2 10<br />
Toothed Lockwashers<br />
“Shakeproof Washers”<br />
The lockwasher is an important part of any fastener assembly. In application,<br />
it provides continuous tension in both an upward and downward direction.<br />
This tension insures tighter, longer-lasting assemblies. Even under conditions<br />
of severe vibration.<br />
• Manufactured from special carbon steel. • Provides positive two-directional locking.<br />
• Keeps assemblies tight. • Uni-zinc plated to resist rust and corrosion.<br />
INTERNAL<br />
TYPE<br />
Provides locking<br />
action under small<br />
head screws.<br />
Also used under<br />
nuts where appearance<br />
is a factor.<br />
Internal teeth<br />
prevent snagging.<br />
BOLT INTERNAL QTY. EXTERNAL QTY.<br />
SIZE PART # PART #<br />
#4 07409 100 07414 100<br />
#6 07410 100 07415 100<br />
#8 07411 100 07416 100<br />
#10 07412 100 07417 100<br />
#12 07413 100 07418 100<br />
1/4 05040 100 05050 100<br />
5/16 05041 100 05051 100<br />
3/8 05042 100 05052 100<br />
7/16 05043 100 05053 100<br />
1/2 05044 100 05054 100<br />
9/16 05045 50 05055 50<br />
5/8 05046 50 05056 50<br />
3/4 05047 50 05057 50<br />
7/8 05048 50 05058 50<br />
1 05049 50 05059 50<br />
Standard Washers<br />
Finishing Washers<br />
Countersunk Type<br />
• Brass.<br />
• Nickel plated.<br />
PART # SIZE QTY.<br />
116070 #4 100<br />
116071 #6 100<br />
116072 #8 100<br />
116073 #10 100<br />
116074 #12 100<br />
116075 #14 100<br />
EXTERNAL<br />
TYPE<br />
Provides torsional resistance against<br />
vibration. Extensive toothed area locking<br />
offers adequate locking action, particularly<br />
where there are oversize holes.<br />
Available in<br />
an Assortment & Kwik Paks<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00505<br />
Found on Page 42<br />
PART # 00794<br />
Found on Page 43<br />
PART # 00505KP<br />
Found on Page 43<br />
Washer Assortments Available<br />
125<br />
FASTENERS
FASTENERS<br />
126<br />
Non-Ferrous <strong>Fasteners</strong><br />
Brass Hex Head Cap Screws<br />
• Manufactured from 100% pure brass.<br />
• Made to exacting quality control standards.<br />
• Full formed hex heads for easier wrenching.<br />
• Clean, burr-free threads.<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH PART # QTY.<br />
3/4 146103 100<br />
1 146105 100<br />
1-1/4 146106 100<br />
1-1/2 146107 100<br />
1/4-20 1-3/4 146108 100<br />
2 146109 100<br />
2-1/4 146110 50<br />
2-1/2 146111 50<br />
2-3/4 146112 50<br />
3 146113 50<br />
3/4 146138 100<br />
1 146140 100<br />
1-1/4 146141 100<br />
1-1/2 146142 100<br />
5/16-18 1-3/4 146143 100<br />
2 146144 100<br />
2-1/4 146145 50<br />
2-1/2 146146 50<br />
3 146147 50<br />
3/4 146173 100<br />
1 146175 100<br />
1-1/4 146176 100<br />
1-1/2 146177 100<br />
3/8-16 1-3/4 146178 100<br />
2 146179 50<br />
2-1/4 146180 50<br />
2-1/2 146181 50<br />
2-3/4 146182 50<br />
3 146183 50<br />
3/4 146239 50<br />
1 146241 50<br />
1-1/4 146242 50<br />
1-1/2 146243 50<br />
1/2-13 1-3/4 146244 50<br />
2 146245 50<br />
2-1/4 146246 50<br />
2-1/2 146247 50<br />
2-3/4 146248 50
Brass Hex Machine Screw Nuts<br />
• Freeze resistant.<br />
• Precision finished threads.<br />
DIAMETER PART # QTY.<br />
6-32 147200 100<br />
8-32 147201 100<br />
10-24 147202 100<br />
10-32 147203 100<br />
1/4-20 147204 100<br />
5/16-18 147205 100<br />
Brass Flatwashers<br />
• Smooth surface.<br />
• Perfectly centered holes.<br />
• Uniform thickness.<br />
DIAMETER PART # QTY.<br />
#6 147220 100<br />
#8 147221 100<br />
#10 147222 100<br />
1/4 147223 100<br />
5/16 147224 100<br />
3/8 147225 50<br />
7/16 147441 50<br />
1/2 147226 50<br />
Brass Finished Hex Nuts<br />
• Chamfered.<br />
• Precision finished threads.<br />
DIAMETER PART # QTY.<br />
1/4-20 147260 100<br />
5/16-18 147261 100<br />
3/8-16 147262 50<br />
7/16-14 147440 50<br />
1/2-13 147263 50<br />
Silicone Bronze Lockwashers<br />
• Uniform thickness.<br />
• Freeze resistant.<br />
Non-Ferrous <strong>Fasteners</strong><br />
DIAMETER PART # QTY.<br />
#6 147240 100<br />
#8 147241 100<br />
#10 147242 100<br />
1/4 147243 100<br />
5/16 147244 100<br />
3/8 147245 50<br />
1/2 147246 50<br />
1 800 458-4018 www.uzengprod.com<br />
127<br />
FASTENERS
FASTENERS<br />
128<br />
Flange <strong>Fasteners</strong><br />
Flange Fastener System<br />
For Heavy Duty Applications<br />
• Meets IFI Grade 8 specifications.<br />
• Phosphate and oil finish.<br />
• Flange Fastener System eliminates need of stocking washers.<br />
• Flange Fastener System reduces time consuming hole preparations<br />
such as countersinking and deburring.<br />
The Flange Fastener System is a 150,000 PSI system equivalent to SAE GR 8<br />
specifications. Dimensions conform to IFI III specifications. This strong and dependable system<br />
meets the demands of most heavy duty applications.<br />
The need to deburr or countersink is reduced. The burrs at edge of the hole<br />
are usually confined in this recess, thereby rarely interfacing with full action of<br />
the load bearing surface.<br />
Matched flanged on bolt and nut distribute the clamping load uniformly over<br />
a wider area, reducing stresses. No load loss through dishing or washer breakage.<br />
The Flange Fastener System incorporates a radius root thread design for improved<br />
fatigue life. Coarse threads are used rather than fine. Coarse threads are less<br />
susceptible to stripping or nicking, assemble easier and faster, and do not generate<br />
excessive heat when used with lock nuts.<br />
Reaming and other costly hole preparations are reduced. Precise hole tolerances<br />
are not required.<br />
Clamp load retention is increased. Friction is distributed and maintained over<br />
a wider area. Resistance to joint slippage is improved and possible shear<br />
failures are reduced.<br />
Stover Locknut (GT) eliminates the need for other locking means. Locking<br />
action is sustained by precision compression of upper threads on the bolt threads.<br />
Will not gall or seize.<br />
1 800 458-4018 www.uzengprod.com
Flange Fastener System<br />
LENGTH ¼-20 DIA. QTY 5/16-18 DIA. QTY 3/8-16 DIA. QTY ½-13 DIA QTY ½-20 DIA QTY<br />
½ 123209* 100 123220* 50<br />
5/8 123210* 100<br />
¾ 123211* 100 123221* 50<br />
1 123212* 100 123222* 50 05500 25 05511 25<br />
1-1/4 123213* 100 123223* 50 05501 25 05512 25 123234* 25<br />
1-1/2 123214* 50 123224* 50 05502 25 05513 25 123235* 25<br />
1-3/4 123215* 50 123225* 50 05503 25 05514 25 123236* 25<br />
2 123216* 50 123226* 50 05504 25 05515 25 123237* 25<br />
2-1/4 123217* 50 123227* 50 05505 25 05516 10 123238* 25<br />
2-1/2 123218* 50 123228* 50 05506 25 05517 10 123239* 25<br />
2-3/4 05518 10<br />
3 123219* 50 123229* 50 123230* 25 05519 10 123240* 25<br />
3-1/4 05520 10<br />
3-1/2 05521 10<br />
3-3/4 05522 10<br />
4 123231* 25 05523 10<br />
4-1/2 05524 10<br />
5 05525 10<br />
FLANGE NUT 123248* 100 123249* 100 05560 50 05561 25 123250* 25<br />
LENGTH 5/8-11 DIA. QTY. 5/8-18 DIA. QTY. ¾-10 DIA. QTY<br />
1-1/4 05529 10<br />
1-1/2 05530 10 123241* 25<br />
1-3/4 05531 10 123242* 25<br />
2 05532 10 123243* 25 05549 5<br />
2-1/4 05533 10 123244* 25 05550 5<br />
2-1/2 05534 10 123245* 25 05551 5<br />
2-3/4 05535 10<br />
3 05536 10 123246* 25 123233* 5<br />
3-1/2 05538 10 05554 5<br />
4 05540 10 123247* 25 05555 5<br />
4-1/2 05541 10<br />
5 05542 10<br />
5-1/2 123232* 10<br />
6 05544 10<br />
FLANGE NUT 05562 25 123251* 25 05563 10<br />
(* NON-STOCK)<br />
Flange <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
129<br />
FASTENERS
FASTENERS<br />
130<br />
Grade 5 Carriage Bolts<br />
Carriage Bolts - Grade 5 Zinc Plated<br />
• Medium strength steel<br />
• Square neck prevents turning once tightened<br />
• Use in square holes for wood-to-wood or wood-to-metal fastening<br />
DIA. LGTH. PART # QTY<br />
1/4-20<br />
5/16-18<br />
3/8-16<br />
7/16-14<br />
* Non-Stock<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
2<br />
2-1/4<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
6<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/2<br />
4<br />
4-1/2<br />
5<br />
6<br />
1-1/4<br />
1-1/2<br />
123094*<br />
123095*<br />
123096*<br />
123097*<br />
123098*<br />
123099*<br />
123100*<br />
123101*<br />
123102*<br />
123103*<br />
123104*<br />
123105*<br />
123106*<br />
123107*<br />
123108*<br />
123109*<br />
123110*<br />
123111*<br />
123112*<br />
123113*<br />
123114*<br />
123115*<br />
123116*<br />
123117*<br />
123118*<br />
123119*<br />
123120*<br />
123121*<br />
123122*<br />
123123*<br />
123124*<br />
123125*<br />
123126*<br />
123127*<br />
123128*<br />
123129*<br />
123130*<br />
100<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
50<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
25<br />
25<br />
25<br />
25<br />
50<br />
50<br />
1 800 458-4018 www.uzengprod.com<br />
DIA. LGTH. PART # QTY<br />
7/16-14<br />
1/2-13<br />
5/8-11<br />
3/4-10<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
8<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
4-1/2<br />
5<br />
6<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
123131*<br />
123132*<br />
123133*<br />
123134*<br />
123135*<br />
123136*<br />
123137*<br />
123138*<br />
123139*<br />
123140*<br />
123141*<br />
123142*<br />
123143*<br />
123144*<br />
123145*<br />
123146*<br />
123147*<br />
123148*<br />
123149*<br />
123150*<br />
123151*<br />
123152*<br />
123153*<br />
123154*<br />
123155*<br />
123156*<br />
123157*<br />
123158*<br />
123159*<br />
123160*<br />
123161*<br />
123162*<br />
123163*<br />
123164*<br />
123165*<br />
123166*<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
10<br />
25<br />
25<br />
25<br />
25<br />
10<br />
10<br />
10<br />
10<br />
10
Carriage Bolts - Grade 2<br />
• USS (NC) threads. • Rolled threads for greater strength.<br />
• Precision cold formed. • Made from SAE approved cold rolled steel.<br />
• Supplied without nuts. • Uni-Zinc plated to resist rust and corrosion.<br />
• Fully squared shoulders eliminate turning.<br />
DIA. LENGTH PART # QTY.<br />
1/2 113750 100<br />
3/4 113751 100<br />
1 113752 100<br />
1-1/4 113753 100<br />
3/16-24 1-1/2 113754 100<br />
1-3/4 113755 100<br />
2 113756 100<br />
2-1/4 113757 100<br />
2-1/2 113758 100<br />
3 113759 100<br />
3-1/2 113760 100<br />
1/2 07200 100<br />
3/4 07201 100<br />
1 07202 100<br />
1-1/4 07203 100<br />
1-1/2 07204 100<br />
1-3/4 07205 100<br />
2 07206 100<br />
2-1/4 07207 100<br />
1/4-20 2-1/2 07208 100<br />
2-3/4 07209 100<br />
3 07210 100<br />
3-1/2 07211 100<br />
4 07212 50<br />
4-1/2 07213 50<br />
5 07214 50<br />
5-1/2 07215 50<br />
6 07216 50<br />
3/4 07217 50<br />
1 07218 50<br />
1-1/4 07219 50<br />
1-1/2 07220 50<br />
1-3/4 07221 50<br />
2 07222 50<br />
2-1/4 07223 50<br />
2-1/2 07224 50<br />
5/16-18 2-3/4 07225 50<br />
3 07226 50<br />
3-1/2 07227 50<br />
4 07228 50<br />
4-1/2 07229 50<br />
5 07230 50<br />
5-1/2 07231 50<br />
6 07232 50<br />
7 07233 50<br />
8 07234 50<br />
DIA. LENGTH PART # QTY.<br />
1 07235 50<br />
1-1/4 07236 50<br />
1-1/2 07237 50<br />
1-3/4 07238 50<br />
2 07239 50<br />
2-1/4 07240 50<br />
2-1/2 07241 50<br />
2-3/4 07242 50<br />
3/8-16 3 07243 50<br />
3-1/2 07244 50<br />
4 07245 50<br />
4-1/2 07246 50<br />
5 07247 50<br />
5-1/2 07248 50<br />
6 07249 50<br />
7 07250 50<br />
8 07251 50<br />
1 07252 25<br />
1-1/4 07253 25<br />
1-1/2 07254 25<br />
1-3/4 07255 50<br />
2 07256 25<br />
2-1/4 07257 25<br />
2-1/2 07258 25<br />
7/16-14 3 07259 25<br />
3-1/2 07260 25<br />
4 07261 25<br />
4-1/2 07262 25<br />
5 07263 25<br />
5-1/2 07264 25<br />
6 07265 25<br />
7 113835 25<br />
8 113836 25<br />
1-1/2 07266 25<br />
2 07267 25<br />
2-1/4 07268 25<br />
2-1/2 07269 25<br />
3 07270 25<br />
3-1/2 07271 25<br />
1/2-13 4 07272 25<br />
4-1/2 07273 25<br />
5 07274 25<br />
5-1/2 07275 25<br />
6 07276 25<br />
7 07277 25<br />
8 07278 25<br />
DIA. LENGTH PART # QTY.<br />
1-1/2 07279 10<br />
2 07280 10<br />
2-1/2 07281 10<br />
3 07282 10<br />
3-1/2 07283 20<br />
4 07284 10<br />
5/8-11 4-1/2 07285 20<br />
5 07286 20<br />
5-1/2 07287 20<br />
6 07288 10<br />
7 07289 20<br />
8 07290 20<br />
3 07291 20<br />
4 07292 20<br />
5 07293 20<br />
3/4-10 5-1/2 07294 20<br />
6 07295 20<br />
7 07296 20<br />
8 07297 20<br />
Available in<br />
an Assortment<br />
PART # 00826<br />
Found on Page 53<br />
1 800 458-4018 www.uzengprod.com<br />
Bolts<br />
131<br />
FASTENERS
FASTENERS<br />
132<br />
Bolts<br />
Shaker Screen Bolts<br />
(Supplied without nuts)<br />
• Grade 5.<br />
• Double heat treated.<br />
• USS (N.C.) threads.<br />
• Fully threaded.<br />
• Plain finish.<br />
DIAMETER LENGTH PART # QTY.<br />
3 116088 50<br />
1/2-13 3-1/2 116089 25<br />
4-1/2 116091 25<br />
2 116096 25<br />
2-1/2 116098 25<br />
3-1/2 116100 25<br />
5/8-11 4 116101 25<br />
4-1/2 116102 25<br />
5 116103 25<br />
6 116104 25<br />
2-3/4 116105 20<br />
3-1/2 116106 20<br />
4 116107 20<br />
3/4-10 4-1/2 116108 20<br />
5 116109 20<br />
5-1/2 116110 20<br />
6 116111 20<br />
Step Bolts - Grade 2<br />
(Supplied without nuts)<br />
• Low profile head.<br />
• USS (N.C.) threads.<br />
• Low carbon steel.<br />
• Plain finish.<br />
DIAMETER LENGTH PART # QTY.<br />
1 116621 100<br />
1/4-20 1-1/4 116622 100<br />
1-1/2 116623 100<br />
2 116625 100<br />
5/16-18<br />
1-1/4<br />
1-1/2<br />
116627<br />
116628<br />
100<br />
100<br />
1 800 458-4018 www.uzengprod.com<br />
Elevator Bolts<br />
(Supplied without nuts)<br />
• Flat countersunk heads.<br />
• USS (N.C.) threads.<br />
• Low carbon steel.<br />
• Plain finish.<br />
DIAMETER LENGTH PART # QTY.<br />
3/4 116600 100<br />
1 116601 100<br />
1/4-20 1-1/4 116602 100<br />
1-1/2 116603 100<br />
1-3/4 116604 100<br />
2 116605 100<br />
1 116606 100<br />
1-1/4 116607 100<br />
5/16-18 1-1/2 116608 100<br />
1-3/4 116609 100<br />
2 116610 100<br />
2-1/2 116611 100<br />
1-1/4 116612 100<br />
3/8-16 1-1/2 116613 100<br />
2 116615 100<br />
2-1/2 116616 100
Grade 2 Tap Bolts<br />
• USS (N.C.) Threads.<br />
• Fully threaded.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
1/4" Diameter<br />
LENGTH PART # QTY.<br />
1 117100 100<br />
1-1/4 117101 100<br />
1-1/2 117102 100<br />
2 117104 100<br />
2-1/2 117106 100<br />
3 117108 100<br />
3-1/2 117110 100<br />
4 117112 100<br />
4-1/2 117114 100<br />
5 117116 100<br />
6 117120 100<br />
5/16" Diameter<br />
LENGTH PART # QTY.<br />
1 117130 100<br />
1-1/4 117131 100<br />
1-1/2 117132 100<br />
2 117134 100<br />
2-1/2 117136 100<br />
3 117138 100<br />
3-1/2 117140 50<br />
4 117142 50<br />
5 117146 50<br />
6 117150 50<br />
3/8" Diameter<br />
LENGTH PART # QTY.<br />
1 117160 100<br />
1-1/4 117161 100<br />
1-1/2 117162 100<br />
1-3/4 117163 100<br />
2 117164 100<br />
2-1/2 117166 50<br />
3 117168 50<br />
3-1/2 117170 50<br />
4 117172 50<br />
4-1/2 117174 50<br />
5 117176 50<br />
6 117180 50<br />
1/2" Diameter<br />
LENGTH PART # QTY.<br />
1 117190 50<br />
1-1/4 117191 50<br />
1-1/2 117192 50<br />
1-3/4 117193 50<br />
2 117194 50<br />
2-1/2 117196 50<br />
3 117198 50<br />
3-1/2 117200 25<br />
4 117202 25<br />
4-1/2 117204 25<br />
5 117206 25<br />
6 117210 25<br />
5/8" Diameter<br />
LENGTH PART # QTY.<br />
1 117220 25<br />
2-1/2 117222 25<br />
3 117224 25<br />
3-1/2 117226 25<br />
4 117228 25<br />
3/4" Diameter<br />
LENGTH PART # QTY.<br />
2 117240 20<br />
2-1/2 117242 20<br />
3 117244 20<br />
3-1/2 117246 20<br />
4 117248 20<br />
1 800 458-4018 www.uzengprod.com<br />
Bolts<br />
Grade 2 Hex Head Cap Screws<br />
SIZE PART # QTY.<br />
3/8-16 X 2 110131 50<br />
5/8-11 X 3 110132 25<br />
7/8-9 X 2 110133 10<br />
7/8-9 X 2-1/4 110134 10<br />
7/8-9 X 5 110135 5<br />
1-8 X 2 110136 5<br />
1-8 X 2-1/4 110185 5<br />
1-8 X 2-1/2 110138 5<br />
1-1/8-8 X 2 110140 5<br />
1-1/8-8 X 2-1/2 110141 5<br />
133<br />
FASTENERS
FASTENERS<br />
134<br />
Bolts<br />
Grade 8 Shaker Screen Bolts<br />
• Supplied without nuts.<br />
• Plain finish.<br />
• USS (NC) threads.<br />
• Fully threaded<br />
1/2" Diameter<br />
LENGTH PART # QTY.<br />
1-1/2 116130 25<br />
2 116131 25<br />
2-1/2 116132 25<br />
3 116133 25<br />
3-1/2 116134 25<br />
4 116135 25<br />
4-1/2 116136 25<br />
5 116137 25<br />
5-1/2 116138 25<br />
6 116139 25<br />
7-1/2 116140 25<br />
8 116141 25<br />
Plow Bolts<br />
(Supplied without nuts)<br />
Grade 5 Flat Head<br />
#3 Head<br />
Black<br />
LENGTH 3/8-16 QTY.<br />
GRADE 5<br />
7/16-14 QTY. 1/2-13 QTY.<br />
1 03450 25<br />
1-1/4 03451 25 03456 25 03462 25<br />
1-1/2 03452 25 03457 25 03463 25<br />
1-3/4 03453 25 03458 25 03464 25<br />
2 03454 25 03459 25 03465 25<br />
2-1/2 03455 25 03460 25 03466 25<br />
3 03461 25 03467 25<br />
1 800 458-4018 www.uzengprod.com<br />
5/8" Diameter<br />
LENGTH PART # QTY.<br />
2 116143 20<br />
2-1/4 116144 20<br />
2-1/2 116145 20<br />
2-3/4 116146 20<br />
3 116147 20<br />
3-1/2 116148 20<br />
4 116149 20<br />
4-1/2 116150 20<br />
5 116151 20<br />
6 116152 20<br />
9 116154 20<br />
10 116155 20<br />
3/4" Diameter<br />
LENGTH PART # QTY.<br />
2 116156 20<br />
2-3/4 116157 20<br />
3 116158 20<br />
3-1/2 116159 20<br />
4 116160 20<br />
4-1/2 116161 20<br />
5 116162 20<br />
5-1/2 116163 20<br />
6 116164 20<br />
7 116165 20<br />
8 116166 20<br />
9 116167 20<br />
Grade 8 Dome Head<br />
#3 Head<br />
Black<br />
LENGTH 5/8-11<br />
GRADE 8<br />
QTY. 3/4-10 QTY.<br />
2 01400 25 01406 25<br />
2-1/4 01401 25 01407 25<br />
2-1/2 01402 25 01408 25<br />
3 01403 10 01409 10<br />
3-1/2 01404 10 01410 10<br />
4 01405 10 01411 10
Alloy Socket Head Screws...<br />
Cap Screw Set Screw Flat Head Button Head<br />
Are engineered to eliminate costly downtime in your plant!<br />
Here’s why...<br />
• Made from the finest alloy steel available.<br />
• Tensile strength up to 180,00 PSI.<br />
• Deep, accurate sockets for maximum wrenching.<br />
• Controlled fillet to increase fatigue strength.<br />
• Controlled concentricity for easier and more accurate assembly.<br />
• Cold forged heads for greater strength.<br />
• Full formed rolled threads for easier assembly & greater strength.<br />
These sectional photos show why <strong>UZ</strong> socket products are the best you can use!<br />
Always available in a complete range of sizes - right off the shelf!<br />
• Unusually long • Small diameter<br />
• Extra short • Large diameter<br />
Socket <strong>Fasteners</strong><br />
Try us first!<br />
We can provide a wide variety of special socket screws, usually in a very short time.<br />
Ask your <strong>UZ</strong> representative to get you a fast quotation.<br />
Socket set screws are normally available from stock with plain cup point. Other point styles are available on special request.<br />
Point Styles<br />
Cup Point Oval Point Flat Point<br />
Cone Point Half Dog Point Full Dog Point<br />
1 800 458-4018 www.uzengprod.com<br />
135<br />
FASTENERS
FASTENERS<br />
136<br />
Socket <strong>Fasteners</strong><br />
Hex Socket Head Cap Screws<br />
1960 Series<br />
• Alloy Steel 160,00 PSI.<br />
• Cold Forged Sockets.<br />
• Black Satin Finish.<br />
• Conforms to ASTM A574 and MIL Spec MIL DTL-1222J.<br />
DIAMETER LENGTH USS (NC)<br />
PART # QTY.<br />
1/4 130117 100<br />
#4 3/8 130118 100<br />
USS = 40 1/2 130119 100<br />
(3/32 Key) 5/8 130120 100<br />
3/4 130121 100<br />
1/4 130135 100<br />
#6 3/8 130136 100<br />
USS = 32 1/2 130137 100<br />
(7/64 Key) 5/8 130138 100<br />
3/4 130139 100<br />
1 130141 100<br />
3/8 130147 100<br />
#8 1/2 130148 100<br />
USS = 32 5/8 130149 100<br />
(9/64 Key) 3/4 130150 100<br />
1 130152 100<br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
3/8 130159 130435 100<br />
1/2 08000 08300 100<br />
#10 5/8 08001 08301 100<br />
(3/16) 3/4 08002 08302 100<br />
USS - 24 1 08003 08303 50<br />
SAE = 32 1-1/4 08004 08304 50<br />
(5/32 Key) 1-1/2 08005 08305 50<br />
1-3/4 130167 130443 50<br />
2 08006 08306 50<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
3/8 130173 130449 50<br />
1/2 08007 08307 50<br />
5/8 130175 130451 50<br />
3/4 08008 08308 50<br />
1/4 1 08009 08309 50<br />
USS = 20 1-1/4 08010 08310 50<br />
SAE = 28 1-1/2 08011 08311 50<br />
(3/16 Key) 1-3/4 08012 08312 50<br />
2 08013 08313 50<br />
2-1/4 08014 08314 50<br />
2-1/2 08015 50<br />
2-3/4 08016 50<br />
3 08017 25<br />
1/2 08018 08315 50<br />
5/8 08019 08316 50<br />
3/4 08020 08317 50<br />
1 08021 08318 50<br />
5/16 1-1/4 08022 08319 50<br />
USS = 18 1-1/2 08023 08320 50<br />
SAE = 24 1-3/4 08024 08321 50<br />
2 08025 08322 50<br />
2-1/4 08026 08323 50<br />
2-1/2 08027 08324 25<br />
2-3/4 130203 25<br />
3 08028 25<br />
Available in<br />
an Assortment<br />
PART # 00700<br />
Found on Page 44<br />
PART # 00206<br />
Found on Page 45<br />
PART # 00923<br />
Found on Page 45
Hex Socket Head Cap Screws<br />
1960 Series<br />
• Alloy Steel 160,000 PSI.<br />
• Cold Forged Sockets.<br />
• Black Satin Finish.<br />
• Conforms to ASTM A574 and MIL Spec MIL DTL-1222J.<br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
1/2 08029 130479 50<br />
5/8 08030 50<br />
3/4 08031 08325 50<br />
7/8 08032 50<br />
1 08033 08326 50<br />
1-1/4 08034 08327 50<br />
1-1/2 08035 08328 50<br />
3/8 1-3/4 08036 08329 25<br />
USS = 16 2 08037 08330 25<br />
SAE = 24 2-1/4 08038 08331 25<br />
(5/16 Key) 2-1/2 08039 08332 25<br />
2-3/4 130222 25<br />
3 08040 08333 25<br />
3-1/2 130225 25<br />
4 130226 25<br />
4-1/2 130227 10<br />
5 130228 10<br />
3/4 08041 25<br />
1 08042 08334 25<br />
1-1/4 08043 08335 25<br />
7/16 1-1/2 08044 08336 10<br />
USS = 14 1-3/4 08045 10<br />
SAE = 20 2 08046 08337 10<br />
(3/8 Key) 2-1/2 08047 10<br />
3 08048 10<br />
3-1/2 130247 10<br />
4 130248 10<br />
Socket <strong>Fasteners</strong><br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
3/4 08049 25<br />
1 08050 08338 25<br />
1-1/4 08051 08339 25<br />
1-1/2 08052 08340 25<br />
1-3/4 08053 08341 10<br />
2 08054 08342 10<br />
1/2 2-1/4 08055 08343 10<br />
USS = 13 2-1/2 08056 08344 10<br />
SAE = 20 2-3/4 08057 10<br />
(3/8 Key) 3 08058 08345 10<br />
3-1/2 130267 10<br />
4 130268 5<br />
4-1/2 130269 5<br />
5 130270 5<br />
5-1/2 130271 5<br />
6 130272 5<br />
1 08059 130515 10<br />
1-1/4 08060 130516 10<br />
1-1/2 08061 130517 10<br />
1-3/4 08062 10<br />
2 08063 130519 10<br />
2-1/4 08064 10<br />
5/8 2-1/2 08065 130520 10<br />
USS = 11 2-3/4 08066 10<br />
SAE = 18 3 08067 10<br />
(1/2 Key) 3-1/2 08068 10<br />
4 08069 10<br />
4-1/2 08070 10<br />
5 08071 10<br />
5-1/2 08072 10<br />
6 08073 10<br />
6-1/2 130296 5<br />
7 130297 5<br />
8 130298 5<br />
1 800 458-4018 www.uzengprod.com<br />
137<br />
FASTENERS
FASTENERS<br />
138<br />
Socket <strong>Fasteners</strong><br />
Hex Socket Head Cap Screws<br />
1960 Series<br />
• Alloy Steel 160,00 PSI.<br />
• Cold Forged Sockets.<br />
• Black Satin Finish.<br />
• Conforms to ASTM A574 and MIL Spec MIL DTL-1222J.<br />
DIAMETER LENGTH PART # QTY.<br />
1-1/4 08082 5<br />
1-1/2 08083 5<br />
1-3/4 08084 5<br />
2 08085 5<br />
2-1/4 08086 5<br />
2-1/2 08087 5<br />
2-3/4 08088 5<br />
3/4 3 08089 5<br />
USS = 10 3-1/4 08090 5<br />
(5/8 Key) 3-1/2 08091 5<br />
4 08092 5<br />
4-1/2 08093 5<br />
5 08094 5<br />
5-1/2 08095 5<br />
6 08096 5<br />
6-1/2 130318 5<br />
7 130319 5<br />
8 130320 5<br />
2 08074 5<br />
2-1/4 130326 5<br />
2-1/2 08075 5<br />
2-3/4 130328 5<br />
3 08076 5<br />
3-1/4 130330 5<br />
7/8 3-1/2 08077 5<br />
USS = 9 4 08078 5<br />
(3/4 Key) 4-1/2 08079 5<br />
5 08080 5<br />
5-1/2 130335 5<br />
6 08081 5<br />
6-1/2 130337 5<br />
7 130338 5<br />
8 130339 5<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH PART # QTY.<br />
2 08097 5<br />
2-1/4 130345 5<br />
2-1/2 08098 5<br />
2-3/4 130347 5<br />
3 08099 5<br />
3-1/4 130349 5<br />
1 3-1/2 08100 5<br />
USS = 8 4 08101 5<br />
(3/4 Key) 4-1/2 08102 5<br />
5 08103 5<br />
5-1/2 130354 5<br />
6 08104 5<br />
6-1/2 130356 5<br />
7 130357 5<br />
8 130358 5<br />
2-1/2 130363 1<br />
3 130364 1<br />
3-1/2 130365 1<br />
4 130366 1<br />
4-1/2 130367 1<br />
1-1/4 5 130368 1<br />
USS = 7 5-1/2 130369 1<br />
(7/8 Key) 6 130370 1<br />
6-1/2 130371 1<br />
7 130372 1<br />
8 130373 1<br />
9 130374 1<br />
10 130375 1<br />
12 130376 1<br />
3 130381 1<br />
3-1/2 130382 1<br />
4 130383 1<br />
4-1/2 130384 1<br />
5 130385 1<br />
1-1/2 5-1/2 130386 1<br />
USS = 6 6 130387 1<br />
(1” Key) 6-1/2 130388 1<br />
7 130389 1<br />
8 130390 1<br />
9 130391 1<br />
10 130392 1<br />
12 130393 1
Hi–Collar Lockwashers<br />
For use with Socket Head Cap Screws.<br />
• Plain Finish.<br />
• Heat Treated.<br />
BOLT<br />
SIZE WIDTH THICKNESS PART # QTY.<br />
#10 .042 .047 131830 100<br />
1/4 .047 .078 05030 100<br />
5/16 .062 .093 05031 100<br />
3/8 .076 .125 05032 100<br />
7/16 .090 .140 05033 100<br />
1/2 .103 .172 05034 100<br />
5/8 .125 .203 05036 50<br />
3/4 .154 .218 05037 50<br />
7/8 .182 .234 05038 25<br />
1 .208 .250 05039 25<br />
Socket <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
139<br />
FASTENERS
FASTENERS<br />
140<br />
Socket <strong>Fasteners</strong><br />
Socket Set Screws<br />
Plain Cup Point<br />
• Heat Treated.<br />
• High Strength Alloy.<br />
• Black Satin Finish.<br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
1/8 130549 100<br />
#4 3/16 130550 100<br />
USS = 40 1/4 130551 100<br />
(.050 Key) 5/16 130552 100<br />
3/8 130553 100<br />
1/8 130574 100<br />
3/16 130575 100<br />
1/4 08105 100<br />
#6 5/16 130577 100<br />
USS = 32 3/8 08106 100<br />
(1/16 Key) 1/2 08107 100<br />
5/8 08108 100<br />
3/4 08109 50<br />
1 08110 50<br />
1/8 130589 100<br />
3/16 130590 100<br />
1/4 08111 100<br />
#8 5/16 130592 100<br />
USS = 32 3/8 08112 100<br />
(5/64 Key) 1/2 08113 100<br />
5/8 08114 50<br />
3/4 08115 50<br />
1 08116 50<br />
3/16 130604 130817 100<br />
1/4 08117 08346 100<br />
#10 5/16 130606 130819 100<br />
(3/16) 3/8 08118 08347 100<br />
USS = 24 7/16 130608 100<br />
SAE = 32 1/2 08119 08348 100<br />
(3/32 Key) 5/8 08120 08349 50<br />
3/4 08121 08350 50<br />
1 08122 08351 50<br />
1-1/4 130614 50<br />
3/16 130619 100<br />
1/4 08123 08352 100<br />
5/16 08124 08353 100<br />
3/8 08125 08354 100<br />
1/4 7/16 130623 100<br />
USS = 20 1/2 08126 08355 100<br />
SAE = 28 5/8 08127 08356 50<br />
(1/8 Key) 3/4 08128 08357 50<br />
1 08129 08358 50<br />
1-1/4 08130 08359 50<br />
1-1/2 08131 50<br />
1-3/4 08132 50<br />
2 08133 50<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00527<br />
Found on Page 45<br />
DIAMETER LENGTH PART # QTY.<br />
USS SAE<br />
1/4 08134 08360 50<br />
5/16 08135 08361 50<br />
3/8 08136 08362 50<br />
5/16 7/16 130640 50<br />
USS = 18 1/2 08137 08363 50<br />
SAE = 24 5/8 08138 08364 50<br />
5/32 Key) 3/4 08139 08365 50<br />
1 08140 08366 25<br />
1-1/4 08141 25<br />
1-1/2 08142 25<br />
1-3/4 08143 25<br />
2 08144 25<br />
1/4 08145 08367 50<br />
5/16 08146 08368 50<br />
3/8 08147 08369 50<br />
3/8 7/16 130657 50<br />
USS = 16 1/2 08148 08370 25<br />
SAE = 24 5/8 08149 08371 25<br />
(3/16 Key) 3/4 08150 08372 25<br />
1 08151 08373 25<br />
1-1/4 08152 08374 25<br />
1-1/2 08153 08375 25<br />
2 08154 25<br />
3/8 130672 25<br />
7/16 7/16 130673 25<br />
USS = 14 1/2 130674 25<br />
(7/32 Key) 3/4 130676 25<br />
1 130678 25<br />
1/2 08155 08376 25<br />
5/8 130691 25<br />
1/2 3/4 130692 130881 25<br />
USS = 13 1 08156 130882 25<br />
SAE = 20 1-1/4 130695 10<br />
(1/4 Key) 1-1/2 08157 10<br />
2 08158 10<br />
2-1/2 08159 10<br />
3 08160 10<br />
5/8 130706 10<br />
5/8 3/4 130707 10<br />
USS = 11 1 130709 10<br />
(5/16 Key) 1-1/4 130710 10<br />
1-1/2 130711 10<br />
3/4 130721 10<br />
3/4 1 130723 10<br />
USS = 10 1-1/2 130725 10<br />
(3/8 Key) 2 130727 5<br />
2-1/2 130728 5<br />
3 130729 5
Socket Set Screws<br />
• High Strength Alloy Steel.<br />
• Black Satin Finish.<br />
FLAT OVAL CONE 1/2 DOG KNURLED<br />
DIAMETER LENGTH POINT POINT POINT POINT CUP POINT QTY.<br />
1/8 131920 131975 132010 132087 100<br />
3/16 131921 131976 132011 132088 100<br />
#4-40 1/4 131922 132089 100<br />
(.050 Key) 5/16 131923 132090 100<br />
3/8 132091 100<br />
1/2 100<br />
5/8 100<br />
1/8 131924 100<br />
3/16 131925 132012 100<br />
1/4 131926 132013 100<br />
#5-40 5/16 100<br />
(1/16 Key) 3/8 100<br />
1/2 100<br />
5/8 100<br />
3/4 100<br />
1/8 131927 132014 132102 100<br />
3/16 131928 132015 132103 100<br />
1/4 131929 131977 132016 132104 100<br />
5/16 131930 131978 132105 100<br />
#6-32 3/8 131931 131979 132017 132106 100<br />
(1/16 Key) 1/2 132107 100<br />
5/8 132108 100<br />
3/4 100<br />
7/8 100<br />
1 100<br />
1/8 131932 132112 100<br />
3/16 131933 131980 132018 132050 132113 100<br />
1/4 131934 131981 132019 132051 132114 100<br />
5/16 131935 132020 132052 132115 100<br />
#8-32 3/8 131936 132021 132053 132116 100<br />
(5/64 Key) 1/2 131937 131982 132022 132054 132117 100<br />
5/8 131938 132118 100<br />
3/4 132119 100<br />
7/8 100<br />
1 100<br />
3/16 131939 131983 132055 132122 100<br />
1/4 131940 131984 132023 132056 132123 100<br />
5/16 131941 132024 132057 132124 100<br />
3/8 131942 131985 132025 132058 132125 100<br />
#10-24 1/2 131943 131986 132026 132059 132126 100<br />
(3/32 Key) 5/8 131944 132127 100<br />
3/4 131945 132128 100<br />
7/8 132129 100<br />
1 132130 100<br />
1-1/4 100<br />
Socket <strong>Fasteners</strong><br />
FLAT POINT<br />
OVAL POINT<br />
CONE POINT<br />
1/2 DOG POINT<br />
KNURLED CUP POINT<br />
1 800 458-4018 www.uzengprod.com<br />
141<br />
FASTENERS
FASTENERS<br />
142<br />
Socket <strong>Fasteners</strong><br />
Socket Set Screws<br />
• High Strength Alloy Steel.<br />
• Black Satin Finish.<br />
FLAT OVAL CONE 1/2 DOG KNURLED<br />
DIAMETER LENGTH POINT POINT POINT POINT CUP POINT QTY.<br />
3/16 131946 100<br />
1/4 131947 131987 132027 132060 132132 100<br />
5/16 131948 131988 132028 132061 132133 100<br />
1/4-20 3/8 131949 131989 132029 132062 132134 100<br />
(1/8 Key) 1/2 131950 131990 132030 132063 132135 100<br />
5/8 131951 131991 132031 132064 132136 100<br />
3/4<br />
7/8<br />
131952 131992 132032 132065 132137 100<br />
1 131953 131993 132033 132066 132139 100<br />
1-1/4 132140 100<br />
1/4 131954 131994 100<br />
5/16 131955 131995 132034 132067 132141 100<br />
3/8 131956 131996 132035 132068 132142 100<br />
5/16-18 1/2 131957 131997 132036 132069 132143 100<br />
(5/32 Key) 5/8 131958 131998 132037 132070 132144 100<br />
3/4 131959 131999 132038 132071 132145 100<br />
7/8 132146 100<br />
1 131960 132000 132039 132072 132147 100<br />
1-1/4 132148 100<br />
1/4 131961 100<br />
5/16 131962 100<br />
3/8 131963 132001 132040 132073 132149 100<br />
3/8-16 1/2 131964 132002 132041 132074 132150 100<br />
(3/16 Key) 5/8 131965 132003 132042 132075 132151 100<br />
3/4 131966 132004 132043 132076 132152 100<br />
7/8 132153 100<br />
1 131967 132005 132044 132077 132154 100<br />
1-1/4 132078 132155 100<br />
3/8 131968 100<br />
1/2 131969 132006 132045 132079 100<br />
1/2-13 5/8 131970 132046 132080 100<br />
(1/4 Key) 3/4 131971 132007 132047 132081 100<br />
1 131972 132008 132048 132082 100<br />
1-1/4 132083 100<br />
5/8-11 1 132084 50<br />
(5/16 Key) 1-1/4 132085 50<br />
1 800 458-4018 www.uzengprod.com<br />
FLAT POINT<br />
OVAL POINT<br />
CONE POINT<br />
1/2 DOG POINT<br />
KNURLED CUP POINT
Flat Head Socket Cap Screws<br />
• Black Satin Finish<br />
• Heat treated alloy steel<br />
• Rockwell Hardness 38-44RC<br />
• Class 3A threads<br />
• Tensile strength 180,000 PSI<br />
LENGTH<br />
1/8<br />
3/16<br />
1/4<br />
5/16<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
KEY SIZE<br />
LENGTH<br />
3/16<br />
1/4<br />
5/16<br />
3/8<br />
7/16<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
3<br />
KEY SIZE<br />
0-80<br />
PART # QTY<br />
120282 100<br />
120283 100<br />
120284 100<br />
120285 100<br />
120286 100<br />
120287 100<br />
.035<br />
5-40<br />
PART # QTY<br />
120324 100<br />
120325 100<br />
120326 100<br />
120327 100<br />
120328 100<br />
120329 100<br />
5/64<br />
1-72<br />
PART # QTY<br />
120288 100<br />
120289 100<br />
120290 100<br />
120291 100<br />
120292 100<br />
120293 100<br />
120294 100<br />
.050<br />
6-32<br />
PART # QTY<br />
120330 100<br />
130919 100<br />
120331 100<br />
130920 100<br />
120332 100<br />
130921 100<br />
120333 100<br />
130923 100<br />
120334 100<br />
120335 100<br />
120336 100<br />
120337 100<br />
120338 100<br />
120339 100<br />
5/64<br />
DIAMETER<br />
2-56<br />
PART # QTY<br />
120295 100<br />
120296 100<br />
120297 100<br />
120298 100<br />
120299 100<br />
120300 100<br />
120301 100<br />
120302 100<br />
120303 100<br />
120304 100<br />
.050<br />
DIAMETER<br />
8-32<br />
PART # QTY<br />
120340 100<br />
120341 100<br />
130928 100<br />
120342 100<br />
130929 100<br />
120343 100<br />
130931 100<br />
120344 100<br />
130932 100<br />
120345 50<br />
120346 50<br />
120347 50<br />
120348 50<br />
3/32<br />
3-48<br />
PART # QTY<br />
120305 100<br />
120306 100<br />
120307 100<br />
120308 100<br />
120309 100<br />
120310 100<br />
120311 100<br />
120312 100<br />
1/16<br />
10-24<br />
PART # QTY<br />
120349 100<br />
120350 100<br />
120351 100<br />
120352 100<br />
130938 100<br />
120353 100<br />
130940 100<br />
120354 100<br />
130941 100<br />
130942 100<br />
130943 100<br />
120355 50<br />
120356 50<br />
120357 50<br />
120358 50<br />
120359 25<br />
1/8<br />
Socket <strong>Fasteners</strong><br />
4-40<br />
PART # QTY<br />
120313 100<br />
120314 100<br />
120315 100<br />
120316 100<br />
120318 100<br />
120319 100<br />
120320 100<br />
120321 100<br />
120322 100<br />
120323 100<br />
1/16<br />
10-32<br />
PART # QTY<br />
120360 100<br />
120361 100<br />
120362 100<br />
120363 100<br />
131050 100<br />
120364 100<br />
131052 100<br />
120365 100<br />
131053 100<br />
120366 100<br />
120367 100<br />
120368 50<br />
120369 50<br />
120370 50<br />
120371 50<br />
120372 25<br />
1/8<br />
1 800 458-4018 www.uzengprod.com<br />
143<br />
FASTENERS
FASTENERS<br />
144<br />
Socket <strong>Fasteners</strong><br />
Flat Head Socket cap Screws<br />
LGTH<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
KEY SIZE<br />
LGTH<br />
1/2<br />
5/8<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/2<br />
4<br />
KEY SIZE<br />
LGTH<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/2<br />
4<br />
KEY SIZE<br />
1/4-20<br />
PART # QTY<br />
120373 100<br />
08161 50<br />
08162 50<br />
08163 50<br />
08164 50<br />
08165 50<br />
08166 50<br />
08167 50<br />
08168 50<br />
120374 50<br />
120375 50<br />
120376 25<br />
120377 25<br />
5/32<br />
3/8-24<br />
PART # QTY<br />
120391 50<br />
08388 50<br />
08389 50<br />
08390 25<br />
08391 25<br />
7/32<br />
3/4-10<br />
PART # QTY<br />
120409 10<br />
120410 10<br />
120411 10<br />
120412 10<br />
120413 10<br />
120414 10<br />
120415 10<br />
120416 5<br />
120417 5<br />
1/2<br />
DIAMETER<br />
1/4-28<br />
PART # QTY<br />
120378 100<br />
08377 50<br />
08378 50<br />
08379 50<br />
08380 50<br />
120379 50<br />
08382 50<br />
120380 50<br />
5/32<br />
7/16-14<br />
PART # QTY<br />
120392 50<br />
120393 50<br />
120394 50<br />
120395 50<br />
1/4<br />
7/8-9<br />
PART # QTY<br />
120418 5<br />
120419 5<br />
120420 5<br />
120421 5<br />
9/16<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER<br />
5/16-18<br />
PART # QTY<br />
08169 50<br />
08170 50<br />
08171 50<br />
120381 50<br />
08172 50<br />
08173 50<br />
08174 50<br />
120382 50<br />
08176 100<br />
120383 50<br />
120384 50<br />
120385 25<br />
3/16<br />
DIAMETER<br />
1/2-13<br />
PART # QTY<br />
08186 25<br />
08187 25<br />
08188 25<br />
08189 25<br />
08190 25<br />
08191 25<br />
120396 25<br />
08192 50<br />
08193 50<br />
120397 10<br />
120398 10<br />
5/16<br />
5/16-24<br />
PART # QTY<br />
08383 50<br />
08384 50<br />
08385 50<br />
08386 50<br />
08387 100<br />
120386 50<br />
3/16<br />
1/2-20<br />
PART # QTY<br />
08392 25<br />
08393 25<br />
08394 25<br />
08395 25<br />
08396 25<br />
08397 25<br />
5/16<br />
3/8-16<br />
PART # QTY<br />
08177 50<br />
120387 50<br />
08178 50<br />
08179 50<br />
08180 25<br />
08181 25<br />
08182 25<br />
08183 25<br />
120388 25<br />
08184 25<br />
08185 50<br />
120389 10<br />
120390 10<br />
7/32<br />
5/8-11<br />
PART # QTY<br />
120399 25<br />
120400 25<br />
120401 25<br />
120402 25<br />
120403 25<br />
120404 25<br />
120405 25<br />
120406 10<br />
120407 10<br />
120408 10<br />
3/8
Button Head Socket Cap Screws<br />
• Black Satin Finish<br />
• Heat treated alloy steel<br />
• Meets ASME/ANSI B18.3 1986 & ASTM F835<br />
• Rockwell Hardness 38-44RC<br />
• Class 3A threads<br />
• Tensile strength 180,000 PSI<br />
DIAMETER<br />
LENGTH 0-80 1-72 2-56 3-48 4-40<br />
PART # QTY PART # QTY PART # QTY PART # QTY PART # QTY<br />
1/8 120422 100 120426 100 120431 100<br />
3/16 120423 100 120427 100 08400 100 08404 100 120437 100<br />
1/4 120424 100 120428 100 08401 100 08405 100 08408 100<br />
5/16 120429 100 120432 100 120433 100 120438 100<br />
3/8 120425 100 120430 100 08402 100 08406 100 08409 100<br />
7/16 120439 100<br />
1/2 08403 100 08407 100 08410 100<br />
5/8 120434 100 120440 100<br />
3/4 120435 100 120441 100<br />
7/8 120442 100<br />
1 120436 100 120443 100<br />
KEY SIZE .035 .050 .050 1/16 1/16<br />
DIAMETER<br />
LENGTH 5-40 6-32 8-32 10-24 10-32<br />
PART # QTY PART # QTY PART # QTY PART # QTY PART # QTY<br />
3/16 120450 100 120458 100<br />
1/4 120444 100 08411 100 08415 100 08420 100 08453 100<br />
5/16 120451 100 120459 100 120467 100 120473 100<br />
3/8 120445 100 08412 100 08416 100 08421 100 08454 100<br />
7/16 120452 100 120460 100 120468 100 120474 100<br />
1/2 120446 100 08413 100 08417 100 08422 100 08455 100<br />
5/8 120447 100 08414 100 08418 100 08423 100 08456 100<br />
3/4 120448 100 120454 100 08419 100 08424 100 08457 100<br />
7/8 120461 100 08425 100 08458 100<br />
1 120449 100 120455 100 120462 100 08426 100 08459 100<br />
1-1/4 120456 100 120463 50 120469 100 120475 100<br />
1-1/2 120457 100 120464 50 120470 100 120476 100<br />
1-3/4 120465 50 120471 50 120477 50<br />
2 120466 50 120472 50 120478 50<br />
KEY SIZE 5/64 5/64 3/32 1/8 1/8<br />
INSTALLATION TOOLS LOCATED ON PAGES 148 - 152<br />
Socket <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
145<br />
FASTENERS
FASTENERS<br />
146<br />
Socket <strong>Fasteners</strong><br />
Button Head Socket Cap Screws<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER<br />
LENGTH 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16<br />
PART # QTY PART # QTY PART # QTY PART # QTY PART # QTY<br />
3/8 08427 50 08460 50 08433 100 08466 100 08439 100<br />
1/2 08428 50 08461 50 08434 50 08467 50 08440 100<br />
5/8 08429 50 08462 50 08435 100 08468 100 08441 50<br />
3/4 08430 50 08463 50 08436 50 08469 50 08441 50<br />
7/8 08431 50 08437 50 08442 100<br />
1 08432 50 08465 50 08438 50 08471 50 08443 50<br />
1-1/4 120479 50 120482 50 08444 100<br />
1-1/2 120480 50 120483 50 120484 25<br />
1-3/4 120481 50 120485 25<br />
2 120486 25<br />
KEY SIZE 5/32 5/32 3/16 3/16 7/32<br />
DIAMETER<br />
LENGTH 3/8-24 1/2-13 5/8-11<br />
1/2 08472 100<br />
5/8 08473 100<br />
3/4 08474 100 120487 25<br />
7/8 08475 50<br />
1 08476 50 08445 25 08449 50<br />
1-1/4 08446 100 08450 50<br />
1-1/2 08447 100 08451 50<br />
2 08448 25 08452 50<br />
KEY SIZE 7/32 5/16 3/8<br />
INSTALLATION TOOLS LOCATED ON PAGES 149 - 152
Socket Head Shoulder Bolts<br />
(Stripper Bolts)<br />
• Heat-treated alloy steel.<br />
• Deep accurate sockets.<br />
• Plain finish.<br />
• Knurled head.<br />
SHOULDER THREADS<br />
DIA. LENGTH DIA. LENGTH PART # QTY.<br />
A B C D<br />
3/8 131750 25<br />
1/2 131751 25<br />
5/8 131752 25<br />
1/4 3/4 10-24 3/8 131753 25<br />
1 131754 25<br />
1-1/4 131755 25<br />
1-1/2 131756 25<br />
3/8 131757 25<br />
1/2 131758 25<br />
5/8 131759 25<br />
5/16 3/4 1/4-20 7/16 131760 25<br />
1 131761 25<br />
1-1/4 131762 25<br />
1-1/2 131763 25<br />
1-3/4 131764 25<br />
3/8 131766 25<br />
1/2 131767 25<br />
5/8 131768 25<br />
3/8 3/4 5/16-18 1/2 131769 25<br />
1 131770 25<br />
1-1/4 131771 25<br />
1-1/2 131772 25<br />
1-3/4 131773 25<br />
2 131774 25<br />
3/4 131784 25<br />
1 131785 25<br />
1-1/4 131786 25<br />
1/2 1-1/2 3/8-16 5/8 131787 25<br />
2 131789 25<br />
2-1/2 131791 25<br />
3 131793 25<br />
5/8 1-1/4 1/2-13 3/4 131799 25<br />
3/4<br />
1-1/2 5/8-11 7/8 131814 10<br />
2 131816 10<br />
Socket <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
B<br />
A<br />
C<br />
D<br />
A. Shoulder Diameter<br />
B. Shoulder Length<br />
C. Thread Diameter<br />
D. Thread Length<br />
147<br />
FASTENERS
FASTENERS<br />
148<br />
Socket Hex Tools<br />
Socket <strong>Products</strong><br />
Hexagon Keys<br />
For use with socket screws!<br />
• Manufactured only from the finest heat-treated alloy steel.<br />
• High strength and toughness to withstand full tightening force.<br />
• Precise hex tolerances assure uniform engagement with all socket surfaces.<br />
• Chamfered end for fast, sure entry and exit from the socket.<br />
ALLEN KEYS meet these specifications” ASME/ ANSI B18.3 and GGG-K-275 AMED<br />
For your protection...<br />
<strong>UZ</strong> stocks only GENUINE ALLEN HEXAGON KEYS AND SETS.<br />
The name “ALLEN” has become synonymous with “QUALITY”<br />
For over 65 years. It pays to use the best!<br />
1 800 458-4018 www.uzengprod.com<br />
SHORT ARM<br />
LENGTH<br />
HEXAGON KEYS<br />
• Black Satin Finish.<br />
Short Arm Data Long Arm Data<br />
LONG ARM<br />
LENGTH<br />
LENGTH OF SHORT ARM LENGTH OF LONG ARM LENGTH OF SHORT ARM LENGTH OF LONG ARM<br />
SIZE PART # QTY. MIN MAX MIN MAX PART # QTY. MIN MAX MIN MAX<br />
.028 175850 2 1/8 5/16 1-1/8 1-5/16<br />
.035 175851 2 1/4 7/16 1-1/8 1-5/16<br />
.050 175852 2 7/16 5/8 1-9/16 1-3/4 175876 2 7/16 5/8 2-3/4 2-15/16<br />
1/16 08923 2 15/32 21/32 1-21/32 1-27/32 08940 2 15/32 21/32 2-29/32 3-3/32<br />
5/64 08924 2 33/64 45/64 1-25/32 1-31/32 08941 2 33/64 45/64 3-3/32 3-9/32<br />
3/32 08925 2 9/16 3/4 1-29/32 2-3/32 08942 2 9/16 3/4 3-9/32 3-15/32<br />
7/64 08926 2 39/64 51/64 2-1/32 2-7/32 08943 2 39/64 51/64 3-15/32 3-21/32<br />
1/8 08927 2 21/32 27/32 2-5/32 2-11/32 08944 2 21/32 27/32 3-21/32 3-27/32<br />
9/64 08928 2 45/64 57/64 2-9/32 2-15/32 08945 2 45/64 57/64 3-27/32 4-1/32<br />
5/32 08929 2 3/4 15/16 2-13/32 2-19/32 08946 2 3/4 15/16 4-1/32 4-7/32<br />
3/16 08930 2 27/32 1-1/32 2-21/32 2-27/32 08947 2 27/32 1-1/32 4-13/32 4-19/32<br />
7/32 08931 2 15/16 1-1/8 2-29/32 3-3/32 08948 2 15/16 1-1/8 4-25/32 4-31-32<br />
1/4 08932 2 1-1/32 1-7/32 3-5/32 3-11/32 08949 2 1-1/32 1-7/32 5-5/32 5-11/32<br />
5/16 08933 2 1-5/32 1-11/32 3-21/32 3-27/32 08950 2 1-5/32 1-11/32 5-29/32 6-3/32<br />
3/8 08934 2 1-9/32 1-15/32 4-5/32 4-11/32 08951 2 1-9/32 1-15/32 6-21/32 6-27/32<br />
7/16 175865 2 1-13/32 1-19/32 4-21/32 4-27/32 175889 2 1-13/32 1-19/32 7-13/32 7-19/32<br />
1/2 08935 2 1-17/32 1-23/32 5-5/32 5-11/32 08952 2 1-17/32 1-23/32 8-5/32 8-11/32<br />
9/16 08936 2 1-21/32 1-27/32 5-21/32 5-27/32 175891 2 1-21/32 1-27/32 8-29/32 9-3/32<br />
5/8 08937 2 1-25/32 1-31/32 6-5/32 6-11/32 175892 2 1-25/32 1-31/32 9-21/32 9-27/32<br />
3/4 08938 2 2-1/32 2-7/32 7-5/32 7-11/32 175893 2 2-1/32 2-7/32 11-5/32 11-11/32<br />
7/8 175870 2 2-9/32 2-15/32 8-5/32 8-11/32 175894 2 2-9/32 2-15/32 12-21/32 12-27/32<br />
1 175871 2 2-17/32 2-23/32 9-5/32 9-11/32 175895 2 2-17/32 2-23/32 14-5/32 14-11/32
Hexagon Keys<br />
Short Arm Wrench Sets – Genuine Allen<br />
11 Short Arm Keys in a Vinyl Pouch<br />
CONTAINS THESE SIZES:<br />
.050, 1/16, 5/64, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8<br />
• A small handy set.<br />
• Contains the most popular sizes.<br />
• Easily carried in pocket or toolbox.<br />
PART # 175900<br />
15 Short Arm Keys in a Vinyl Pouch<br />
CONTAINS THESE SIZES:<br />
.028, .035, .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8<br />
• For those who need greater size coverage.<br />
• Perfect in every tool box.<br />
PART # 175901<br />
15 Short Arm Keys in a Metal Box<br />
CONTAINS THESE SIZES:<br />
.028, .035, .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8<br />
• For the real pro. This set contains 15 popular short arm keys.<br />
• Packed in a rugged metal box with a fit selector guide on the inside cover.<br />
PART # 175903<br />
13 Long Keys in a Vinyl Pouch<br />
CONTAINS THESE SIZES:<br />
.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64,<br />
5/32, 3/16, 7/32, 1/4, 5/16, 3/8<br />
• 13 popular inch-sizes.<br />
• Packed in a vinyl pouch.<br />
PART # 175902<br />
Socket Hex Tools<br />
Photo needed<br />
State to provide<br />
1 800 458-4018 www.uzengprod.com<br />
149<br />
FASTENERS
FASTENERS<br />
150<br />
Socket Hex Tools<br />
T-Handle Hex Key Wrenches<br />
• Loop T-Handle provides a better grip.<br />
• Keys can be hung up - saves loss.<br />
• Hardened for strength and durability.<br />
• 6" and 9" lengths available.<br />
T-Handle Hex Key Wrench Sets<br />
• Loop T-Handle provides a better grip.<br />
• Handy stand included - keeps set organized.<br />
• Convenient sizing chart is on each stand.<br />
• Each set complete with all 10 wrenches.<br />
• Stand has additional slots for more sizes<br />
Fold–Up Hex Key Sets<br />
• Popular size ranges.<br />
• Use at any angle... key sets snap up in position.<br />
• Precision tolerances, heat treated alloy steel.<br />
The “Fold–Up ”<br />
• Unique “double-foldout” design.<br />
• Specially designed for ease of use.<br />
• High strength alloy steel bits.<br />
Wrenches open from<br />
the top and the bottom,<br />
for easy access and use.<br />
Rounded edges never<br />
cut hands or catch<br />
clothing.<br />
1 800 458-4018 www.uzengprod.com<br />
6" LENGTH 9" LENGTH<br />
SIZE PART # PART #<br />
3/32-3/8 08920 175621<br />
PART # SIZES # KEYS<br />
08917 .050, 1/16, 5/64, 3/32, 7/64,<br />
1/8, 9/64, 5/32<br />
8 Reg.<br />
08918 5/64, 3/32, 7/64, 1/8, 9/64,<br />
5/32, 3/16, 7/32, 1/4<br />
9 Reg.<br />
175905 3/32, 7/64, 1/8, 9/64, 5/32<br />
3/16, 7/32, 1/4<br />
8 Long<br />
08919 3/16, 7/32, 1/4, 5/16, 3/8 5 Long<br />
08969 T10, T15, T20, T25, T27, 7 Torx ®<br />
T30, T40<br />
PART # SIZES # KEYS<br />
91579 .050, 1/16, 5/64, 3/32, 7/64,<br />
1/8, 9/64, 5/32, 3/16<br />
9 Reg.<br />
91580 5/64, 3/32, 7/64, 1/8, 9/64,<br />
5/32, 3/16, 7/32, 1/4<br />
9 Reg.<br />
91581 T10, T15, T20, T25, T27, 7 Torx ®<br />
T30, T40<br />
Rotates 270 Degrees to a firm<br />
stop for a better torquing<br />
and safety.<br />
Handle is specially<br />
contoured for better<br />
feel and control.<br />
6" LENGTH 9" LENGTH<br />
SIZE PART # PART # QTY.<br />
3/32 08959 175592 2<br />
7/64 08960 175595 2<br />
1/8 08961 175598 2<br />
9/64 08962 175601 2<br />
5/32 08963 175604 2<br />
3/16 08964 175607 2<br />
7/32 08965 175610 2<br />
1/4 08966 175613 2<br />
5/16 08967 175616 2<br />
3/8 08968 175619 2
Balldriver ®<br />
Hex Tools<br />
ANGLE ENTRY TO 25°<br />
• Works in hard to reach areas.<br />
• Faster insertion and removal.<br />
Balldriver ® Hex Tool Sets<br />
• New easy hold package with locking feature... goes anywhere.<br />
FAST FUNNEL ENTRY<br />
• Eliminates wasted time even<br />
in blind applications.<br />
• Full depth engagement.<br />
• Reduces “stripping” problems.<br />
Socket Hex Tools<br />
ERGONOMIC DESIGN<br />
• Allows natural hand and<br />
wrist rotation.<br />
• Turns full 360° location.<br />
• Reduces user fatigue.<br />
PART # SIZE QTY. PART # SIZE QTY.<br />
08900 .050 1 08908 3/16 1<br />
08902 5/64 1 08909 7/32 1<br />
08903 3/32 1 08910 1/4 1<br />
08904 7/64 1 08911 5/16 2<br />
08905 1/8 2 08912 3/8 2<br />
08906 9/64 2 08913 7/16 2<br />
08907 5/32 1 08914 1/2 2<br />
PART # SIZE QTY.<br />
08915 7/64, 1/8, 9/64<br />
5/32, 3/16, 7/32,<br />
1/4, 5/16<br />
8<br />
.050, 1/16, 5/64, 13<br />
08916 3/32, 7/64, 1/8,<br />
9/64, 5/32, 3/16,<br />
7/32, 1/4, 5/16, 3/8<br />
Balldriver ® L–Wrench Sets<br />
• Ball end for convenience and speed of off-axis rotation.<br />
• Long end for leverage to attain full torque.<br />
• Packed in patented key case. Wrenches slip<br />
easily into marked slots and stay secured.<br />
PART # SIZE QTY.<br />
91583 .050, 1/16, 5/64,<br />
3/32, 7/32, 7/64,1/4, 1/8,<br />
9/64, 5/16,5/32, 3/8,3/16,<br />
13<br />
1 800 458-4018 www.uzengprod.com<br />
151<br />
FASTENERS
FASTENERS<br />
152<br />
Socket Hex Tools<br />
Hexagon Keys<br />
Hex Key Fit Selector-Keys fit these products<br />
NOMINAL SOCKET HEAD FLAT HEAD BUTTON HEAD LOWHEAD NOMINAL<br />
KEY SIZE, CAP SCREWS SOCKET CAP SOCKET CAP SET SHOULDER PRESSURE ALLE- SOCKET CAP KEY SIZE<br />
INCHES 1960 SERIES 1936 SERIES SCREWS SCREWS SCREWS SCREWS PLUGS NUTS SCREWS INCHES<br />
.028 — — — — 0 — — — — .028<br />
.035 — — 0 0 1,2 — — — — .035<br />
.050 0 0,1 1,2 1,2 3,4 — — — 4 .050<br />
1/16 1 2 3,4 3,4 5,6 — — — 5,6 1/16<br />
5/64 2,3 3,4 5,6 5,6 8 — — — 8 5/64<br />
3/32 4,5 5,6 8 8 10 — — — 10 3/32<br />
7/64 6 — — — — — — — — 7/64<br />
1/8 — 8 10 10 1/4 1/4 4,5 1/4 1/8 —<br />
9/64 8 10 — — — — — — — 9/64<br />
5/32 10 1/4 1/4 1/4 5/16 5/16 1/16 6 5/16 5/32<br />
3/16 1/4 — 5/16 5/16 3/8 3/8 1/8 8,10 3/8 3/16<br />
7/32 — 5/16 3/8 3/8 7/16 — — 7/16 7/32<br />
1/4 5/16 — 7/16 — 1/2 1/2 1/4 1/4 1/2 1/4<br />
5/16 3/8 3/8, 7/16 1/2 1/2 5/8 5/8 3/8 5/16 5/8 5/16<br />
3/8 7/16, 1/2 1/2 5/8 — 3/4 3/4 1/2 3/8 — 3/8<br />
7/16 — — — — — — — 7/16 — 7/16<br />
1/2 5/8 5/8 3/4 — 7/8 1 — 1/2 — 1/2<br />
9/16 — 3/4, 7/8 7/8 — 1, 1-1/8 — 3/4 — — 9/16<br />
5/8 3/4 1 1 — 1-1/4,1-3/8 1-1/4 1 5/8 — 5/8<br />
3/4 7/8, 1 1-1/8, 1-1/4, 1-3/8 1-1/8 — 1-1/2 — 1-1/4 3/4 — 3/4<br />
7/8 1-1/8, 1-1/4 — 1-1/4, 1-3/8 — — 1-1/12 — 7/8 — 7/8<br />
1 1-3/8, 1-1/2 1-1/2 1-1/2 — 1-3/4, 2 1-3/4 1-1/2, 2 1 — 1<br />
1-1/4 1-3/4 — — — — 2 — 1-1/4 — 1-1/4<br />
1-1/2 2 — — — — — — 1-1/2 — 1-1/2<br />
1-3/4 2-1/4, 2-1/2 — — — — — — — — 1-3/4<br />
2 2-3/4 — — — — — — — — 2<br />
Hex Key Tips<br />
Protect Yourself:<br />
Wear safety goggles at all times. Maintain a firm stance<br />
in relation to the work. Apply proper leverage with a uniform<br />
pulling action-do not push. Wear gloves when possible.<br />
Select the Right Tool:<br />
Hand Tools are designed for particular applications.<br />
Always use the proper tool size and type for the<br />
job. Avoid tool substitution and don’t exceed rated<br />
strength limits.<br />
Protect Your Tools:<br />
Secure your Hand Tools in their cases, stands or<br />
boxes. Proper storage of these tools will keep them<br />
protected and accessible. A light, protective oil coating<br />
will prevent corrosion.<br />
1 800 458-4018 www.uzengprod.com<br />
Inspect Your Tools:<br />
Check tools regularly for wear. Replace keys with new keys when<br />
corners or ends become worn or rounded. Keys with a permanent<br />
twist should be discarded.<br />
Remember...<br />
Fully insert key into fastener socket to assure full engagement.<br />
Keep fastener sockets clean. Refer to product specifications for<br />
correct tightening torque.<br />
WARNING:<br />
The use of a pipe extension on a Hex Wrench or Hand Tool is<br />
hazardous to user safety.
B-7 Alloy Threaded Rod<br />
Fully Threaded 36" Lengths<br />
• Manufactured to ASTM-A193 Specifications.<br />
• For high temperature applications up to 1100°F.<br />
• 125,000 PSI minimum tensile strength.<br />
• High tensile 4140 steel - 125,000 PSI.<br />
• Yellow Zinc Dichromate Plated<br />
USS SAE<br />
SIZE PART # SIZE PART # QTY.<br />
1/4-20 05173 1/4-28 05186 1<br />
5/16-18 05174 5/16-24 05187 1<br />
3/8-16 05175 3/8-24 05188 1<br />
7/16-14 05176 7/16-20 05189 1<br />
1/2-13 05177 1/2-20 05190 1<br />
9/16-12 05178 9/16-18 05191 1<br />
5/8-11 05179 5/8-18 05192 1<br />
3/4-10 05180 3/4-16 05193 1<br />
7/8-9 05181 1<br />
1-8 05182 1<br />
Brass Threaded Rod<br />
36" Lengths<br />
• Made from 100% pure brass.<br />
• Chamfered on both ends.<br />
• Rolled threads for greater strength.<br />
• Perfect for all maintenance uses.<br />
SIZE PART # QTY.<br />
6-32 147320 1<br />
8-32 147321 1<br />
10-24 147322 1<br />
10-32 147323 1<br />
1/4-20 147324 1<br />
5/16-18 147325 1<br />
3/8-16 147326 1<br />
7/16-14 147327 1<br />
1/2-13 147328 1<br />
5/8-11 147330 1<br />
3/4-10 147331 1<br />
7/8-9 147332 1<br />
1-8 147333 1<br />
B–7 Threaded Rod<br />
1 800 458-4018 www.uzengprod.com<br />
153<br />
FASTENERS
FASTENERS<br />
154<br />
Threaded & Unthreaded Rod<br />
Fully Threaded Forming Rod<br />
• 1018 Low Carbon Steel for forming and machining.<br />
• Chamfered on both ends for easier starting.<br />
• Can easily be welded or brazed.<br />
• Uni-Zinc plating to resist rust and corrosion.<br />
• Meets specification ASTM A108<br />
Typical Uses...<br />
• Linkage Rods • Adjusting Rods • U-Bolts<br />
• Anchor Bolts • Shafts • Push Rods<br />
• Control Rods • Locking Pins • Other Special Shapes<br />
USS (N.C.) SIZES<br />
36" 72"<br />
SIZE PART # PART # QTY.<br />
6-32 111902 116640 1<br />
8-32 111903 116641 1<br />
10-24 111904 116642 1<br />
1/4-20 05147 116643 1<br />
5/16-18 05148 116644 1<br />
3/8-16 05149 116645 1<br />
7/16-14 05150 116646 1<br />
1/2-13 05151 116647 1<br />
9/16-12 05152 116648 1<br />
5/8-11 05153 116649 1<br />
3/4-10 05154 116650 1<br />
7/8-9 05155 116651 1<br />
1-8 05156 116652 1<br />
1-1/8-7 05157 116653 1<br />
1-1/4-7 05158 116654 1<br />
1-3/8-6 116655 1<br />
1-1/2-6 05159 116656 1<br />
Coupling Nuts found on page 119.<br />
Unthreaded Rod<br />
• All sizes 36" long.<br />
• Easy to cut, form or bend.<br />
• Made from SAE approved cold rolled steel.<br />
• Can be welded or brazed.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
• Hundreds of maintenance uses.<br />
1 800 458-4018 www.uzengprod.com<br />
SAE (N.F.) SIZES<br />
36" 72"<br />
SIZE PART # PART # QTY.<br />
10-32 111905 116670 1<br />
1/4-28 05160 116671 1<br />
5/16-24 05161 116672 1<br />
3/8-24 05162 116673 1<br />
7/16-20 05163 116674 1<br />
1/2-20 05164 116675 1<br />
9/16-18 05165 116676 1<br />
5/8-18 05166 116677 1<br />
3/4-16 05167 116678 1<br />
7/8-14 05168 116679 1<br />
1-14 05169 116680 1<br />
1-1/8-12 05170 116681 1<br />
1-1/4-12 05171 116682 1<br />
1-3/8-12 116703 116683 1<br />
1-1/2-12 05172 116684 1<br />
Available in<br />
an Assortment<br />
PART # 00605<br />
Found on Page 46<br />
DIAMETER PART # QTY.<br />
1/4 111929 1<br />
5/16 111930 1<br />
3/8 111931 6<br />
7/16 111932 3<br />
1/2 111933 3<br />
5/8 111934 3<br />
3/4 111935 2<br />
7/8 111936 2<br />
1 111937 1
Machine Screws<br />
• Available in a wide range of diameters and head styles.<br />
• Many types are available in convenient maintenance assortments.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
• Manufactured to exacting standards for consistent high quality.<br />
3/8<br />
5/8<br />
7/8<br />
1-1/8<br />
1-3/8<br />
1-5/8<br />
1-7/8<br />
2-1/8<br />
2-3/8<br />
2-5/8<br />
2-7/8<br />
3/8<br />
5/8<br />
7/8<br />
1-1/8<br />
Measuring<br />
Scale for<br />
Flat Heads<br />
Oval Heads<br />
1/4<br />
1/2<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
3-3/4<br />
4<br />
1/8<br />
3/8<br />
5/8<br />
7/8<br />
1-1/8<br />
1-3/8<br />
1-5/8<br />
1-7/8<br />
2-1/8<br />
2-3/8<br />
2-5/8<br />
2-7/8<br />
3-1/8<br />
3-3/8<br />
3-5/8<br />
3-7/8<br />
Measuring<br />
Scale for<br />
Round Head<br />
Pan Head<br />
Fillister Head<br />
1/4<br />
1/2<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
3-3/4<br />
4<br />
Machine Screw <strong>Fasteners</strong><br />
Head Styles Available:<br />
ROUND FLAT<br />
OVAL PAN<br />
TRUSS FILLISTER<br />
Available in<br />
an Assortments<br />
& Kwik Paks<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00707<br />
Found on Page 46<br />
PART # 00708<br />
Found on Page 47<br />
PART # 00709<br />
Found on Page 47<br />
PART # 00707KP<br />
Found on Page 46<br />
PART # 00708KP<br />
Found on Page 47<br />
PART # 00709KP<br />
Found on Page 48<br />
155<br />
FASTENERS
FASTENERS<br />
156<br />
Machine Screw <strong>Fasteners</strong><br />
Machine Screws<br />
• A complete range of sizes • Produced from SAE approved steel<br />
• Uni-Zinc plated • Chamfered point for easier starting<br />
• Deep slots for easier tightening • Clean sharp threads for fast, easy use<br />
• Full fillets for greater resistance<br />
to heads snapping off<br />
PHILLIPS PHILLIPS PHILLIPS PHILLIPS<br />
DIA. LENGTH ROUND QTY. FLAT QTY. PAN QTY. TRUSS QTY.<br />
HEAD HEAD HEAD HEAD<br />
1/4 06825 100 06920 100 06870 100<br />
3/8 06826 100 06921 100 06871 100<br />
1/2 116470 100 06922 100 06872 100<br />
5/8 06873 100<br />
4-40 3/4 107944 100 06924 100 06874 100<br />
7/8<br />
1 107945 100 107995 100 06875 100<br />
1-1/4 122729* 100 122711* 100 122737* 100<br />
1-1/2 122712* 100 122738* 100<br />
2 122739* 100<br />
1/4 06827 100 06925 100 06876 100<br />
3/8 06828 100 06926 100 06877 100 110298 100<br />
1/2 06829 100 06927 100 06878 100 110299 100<br />
5/8 06879 100 110300 100<br />
3/4 06830 100 06928 100 06880 100 110301 100<br />
6-32 7/8 100 116545 100<br />
1 116481 100 06929 100 06881 100 110302 100<br />
1-1/4 122730* 100 122713* 100 122740* 100 110303 100<br />
1-1/2 107946 100 107996 100 107967 100<br />
1-3/4<br />
2 122731* 100 122714* 100 122741* 100<br />
2-1/2 122715* 100 122742* 100<br />
3 122716* 100 122743* 100<br />
1/4 06831 100 06930 100 06882 100<br />
3/8 06832 100 06931 100 06883 100 110304 100<br />
1/2 06833 100 06932 100 06884 100 110305 100<br />
5/8 06834 100 06933 100 06885 100 110306 100<br />
3/4 06835 100 06934 100 06886 100 110307 100<br />
7/8 06935 100 06887 100<br />
1 06836 100 06936 100 06888 100 110308 100<br />
8-32 1-1/4 122732* 100 122717* 100 122744* 100 110309 100<br />
1-1/2 116493 100 107997 100 107968 100 110310 100<br />
1-3/4<br />
2 107947 50 107998 50 107969 50 110311 100<br />
2-1/4<br />
2-1/2 122718* 100 122745* 100<br />
2-3/4<br />
3 122719* 100 122746* 100<br />
4 122747* 50<br />
* Denotes non-stock item<br />
Phillips Round Phillips Flat Phillips Pan Phillips Truss<br />
1 800 458-4018 www.uzengprod.com
Machine Screws<br />
PHILLIPS PHILLIPS PHILLIPS PHILLIPS<br />
DIA. LENGTH ROUND QTY. FLAT QTY. PAN QTY. TRUSS QTY.<br />
HEAD HEAD HEAD HEAD<br />
1/4<br />
3/8 06837 100 06937 100 06889 100 110313 100<br />
1/2 06838 100 06938 100 06890 100<br />
5/8 110315 100<br />
3/4 06839 100 06939 100 06891 100 110316 100<br />
7/8<br />
1 06840 100 06940 100 06892 100 110317 100<br />
1-1/4 116501 50 116566 50 06893 50 110318 100<br />
10-24 1-1/2 116502 50 116567 50 107970 50 110319 100<br />
1-3/4 116503 50 107971 50<br />
2 116504 50 116569 50 107972 50 110320 100<br />
2-1/4<br />
2-1/2 107948 50 107999 50 107973 50<br />
2-3/4<br />
3 122733* 100 122720* 100 122748* 100<br />
3-1/2<br />
4 122734* 50 122721* 50 122749* 50<br />
6<br />
1/4<br />
3/8 06841 100 06941 100 06894 100 110321 100<br />
1/2 06842 100 06942 100 06895 100 110322 100<br />
5/8 110323 100<br />
3/4 06843 100 06943 100 06896 100 110324 100<br />
7/8<br />
1 06844 100 06944 100 06897 100 110325 100<br />
10-32 1-1/4 122735* 100 116577 50 107974 50 110326 100<br />
1-1/2 116513 50 116578 50 107975 50 110327 100<br />
1-3/4 107949 50 108000 50 107976 50<br />
2 107950 50 116580 50 107977 50 110328 100<br />
2-1/4<br />
2-1/2 107951 50 108001 50 107978 50<br />
2-3/4<br />
3 122736* 100 122722* 100 122750* 100<br />
1/4<br />
3/8 06845 100<br />
1/2 06846 100 06945 100 06899 100<br />
5/8 06946 100<br />
3/4 06848 100 06947 100 06901 100<br />
7/8<br />
1 06850 100 06948 100 06903 100<br />
12-24 1-1/4 06851 50 06949 50<br />
1-1/2 06852 50 06950 50<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
* Denotes non-stock item<br />
Phillips Round Phillips Flat Phillips Pan Phillips Truss<br />
Machine Screw <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
157<br />
FASTENERS
FASTENERS<br />
158<br />
Machine Screw <strong>Fasteners</strong><br />
Machine Screws<br />
Phillips Round Phillips Flat Phillips Pan Phillips Truss<br />
PHILLIPS PHILLIPS PHILLIPS PHILLIPS<br />
DIA. LENGTH ROUND QTY. FLAT QTY. PAN QTY. TRUSS QTY.<br />
HEAD HEAD HEAD HEAD<br />
3/8 06855 100 06908 100 110329 100<br />
1/2 06856 100 06952 100 06909 100 110330 100<br />
5/8 110331 100<br />
3/4<br />
7/8<br />
06857 100 06953 100 06910 100 110332 100<br />
1 06858 50 06954 50 06911 50 110333 100<br />
1-1/4 06859 50 06955 50 06912 50 110336 100<br />
1/4-20 1-1/2 06860 50 06956 50 06913 50 110337 100<br />
1-3/4 06861 50 108002 50 06914 50 110338 100<br />
2 06862 50 06957 50 06915 50 110339 100<br />
2-1/4 107952 50 108003 50 107979 50<br />
2-1/2 107953 50 108004 50 107980 50 110340 100<br />
2-3/4 107954 50 108005 50 107981 50<br />
3 107955 50 108006 50 107982 50 110341 100<br />
3-1/2 122723* 50 122751* 50<br />
4<br />
5<br />
6<br />
122724* 50 122752* 50<br />
1/2<br />
5/8<br />
108007 50 107983 50<br />
3/4 107956 50 108008 50 107984 50<br />
1 107957 50 108009 107985 50<br />
1-1/4 107958 50 108010 50 107986 50<br />
1-1/2 107959 50 108011 50 107987 50<br />
5/16-18 1-3/4 107960 50 108012 50 107988 50<br />
2<br />
2-1/4<br />
107961 50 107989 50<br />
2-1/2 122725* 50<br />
3<br />
4<br />
5<br />
6<br />
1/2<br />
122726* 50<br />
3/4 107962 50 108013 50 107990 50<br />
1 107963 50 108014 50 107991 50<br />
3/8-16 1-1/4<br />
1-1/2 107964 50 108015 50 107992 50<br />
1-3/4 107965 50 108016 50 107993 50<br />
2 107966 50 108017 50 107994 50<br />
2-1/2 122727* 50<br />
3 122728* 50<br />
* Denotes non-stock item<br />
Phillips Flat Undercut Head<br />
•For use in installing door hinges.<br />
PART # DIA. QTY.<br />
07853 12-24 x 1/2 100<br />
1 800 458-4018 www.uzengprod.com
Brass Machine Screws<br />
• Manufactured from 100% pure brass.<br />
• Clean, sharp, burr-free threads.<br />
• Deep, fully formed slots.<br />
SLOTTED SLOTTED<br />
DIAMETER LENGTH ROUND FLAT QTY.<br />
HEAD HEAD<br />
1/4 146800 147000 100<br />
5/16 147001 100<br />
3/8 146802 147002 100<br />
1/2 146804 147004 100<br />
#6-32 5/8 146806 147006 100<br />
3/4 146807 147007 100<br />
1 146809 147009 100<br />
1-1/4 146811 147011 100<br />
1-1/2 146813 147013 100<br />
2 146815 147015 100<br />
1/4 146828 147028 100<br />
5/16 146829 147029 100<br />
3/8 146830 147030 100<br />
1/2 146832 147032 100<br />
5/8 146834 147034 100<br />
#8-32 3/4 146835 147035 100<br />
1 146837 147037 100<br />
1-1/4 146839 147039 100<br />
1-1/2 146841 147041 100<br />
2 146843 147043 100<br />
2-1/2 146845 147045 100<br />
3 146847 147047 100<br />
1/4 146856 147056 100<br />
5/16 146857 147057 100<br />
3/8 146858 147058 100<br />
1/2 146859 147060 100<br />
5/8 146861 147062 100<br />
#10-24 3/4 146862 147063 100<br />
1 146864 147065 100<br />
1-1/4 146866 147067 100<br />
1-1/2 146868 147069 100<br />
2 146870 147071 100<br />
2-1/2 146872 147073 100<br />
3 146874 147075 100<br />
Non–Ferrous Machine Screw <strong>Fasteners</strong><br />
Slotted Round Slotted Flat<br />
• Available in round and flat heads.<br />
• Highest quality.<br />
SLOTTED SLOTTED<br />
DIAMETER LENGTH ROUND FLAT QTY.<br />
HEAD HEAD<br />
1/4 146883 147084 100<br />
5/16 146884 147085 100<br />
3/8 146885 147086 100<br />
1/2 146887 147088 100<br />
#10-32 5/8 146889 147090 100<br />
3/4 146890 147091 100<br />
1 146892 147093 100<br />
1-1/4 146894 147095 100<br />
1-1/2 146896 147097 100<br />
2 146898 147099 100<br />
2-1/2 146900 147101 100<br />
3 146902 147103 100<br />
3/8 146913 147112 100<br />
1/2 146915 147114 100<br />
5/8 146917 147116 100<br />
3/4 146918 147117 100<br />
1/4-20 1 146920 147119 100<br />
1-1/4 146922 147121 100<br />
1-1/2 146924 147123 100<br />
2 146926 147125 100<br />
2-1/2 146928 147127 100<br />
3 146930 147129 100<br />
1/2 146939 147138 100<br />
3/4 146942 147140 100<br />
1 146944 147142 100<br />
5/16-18 1-1/4 146946 147144 100<br />
1-1/2 146948 147146 100<br />
2 146950 147148 50<br />
2-1/2 146952 147150 50<br />
3 146954 174152 50<br />
Available in<br />
an Assortment<br />
Slotted Round Slotted Flat<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00677<br />
Found on Page 48<br />
159<br />
FASTENERS
FASTENERS<br />
160<br />
Thumb Screw <strong>Fasteners</strong><br />
Thumb Screws<br />
• Low carbon steel.<br />
• Zinc Plated<br />
WITHOUT WITH<br />
SIZE SHOULDER QTY. SHOULDER QTY.<br />
PART # PART #<br />
6-32 x 1 116309 25<br />
8-32 x 1 116314 25<br />
10-24 x 1 116319 25 116368 25<br />
10-32 x 1 116326 25<br />
1/4-20 x 3/4 116331 25 116376 25<br />
1/4-20 x 1 116332 25 116377 25<br />
1/4-20 x 1-1/4 116333 25<br />
1/4-20 x 1-1/2 116334 25<br />
1/4-20 x 2 116335 25 116379 25<br />
5/16-18 x 1 116339 25 116382 25<br />
5/16-18 x 2 116342 25<br />
3/8-16 x 1 116346 25 116385 25<br />
3/8-16 x 2 116387 25<br />
1 800 458-4018 www.uzengprod.com<br />
Without Shoulder<br />
With Shoulder
Sheet Metal Screws<br />
Sheet Metal Screw <strong>Fasteners</strong><br />
• Uni-Zinc plated. •Deep slots for easier tightening.<br />
• Sharp points for easy starting. •Produced from SAE approved steel.<br />
• Consistent hardness without being brittle. •Full fillets for greater resistance to heads snapping off.<br />
DIA. LENGTH<br />
1/4<br />
3/8<br />
1/2<br />
#4 5/8<br />
3/4<br />
7/8<br />
1<br />
1/4<br />
3/8<br />
1/2<br />
5/8<br />
#6 3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
3/8<br />
1/2<br />
5/8<br />
#7 3/4<br />
1<br />
1-1/4<br />
1/4<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
#8 7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
PHILLIPS PHILLIPS PHILLIPS SLOTTED<br />
FLAT PAN OVAL HEX HEXWASHER QTY.<br />
HEAD HEAD HEAD HEAD HEAD<br />
05810 06230 05865 100<br />
05811 06231 05866 100<br />
05812 06232 05867 100<br />
05813 06233 05868 100<br />
05814 06234 05869 100<br />
06235 100<br />
05815 06236 05870 100<br />
05816 06237 100<br />
05817 06039 05872 06280 06083 100<br />
05818 06040 05873 06281 06084 100<br />
05819 06238 05874 06282 06085 100<br />
05820 06041 05875 06283 06086 100<br />
06239 100<br />
05821 06042 05876 06087 100<br />
05822 06240 05877 100<br />
05823 06241 05878 100<br />
06242 100<br />
05824 06243 05879 100<br />
05825 06244 05880 100<br />
05826 06245 05881 100<br />
05827 06247 05882 100<br />
05883 100<br />
114168 100<br />
05830 06043 05885 06059 06088 100<br />
05831 06044 05886 06060 06089 100<br />
05832 06250 05887 06285 06090 100<br />
05833 06045 05888 06286 06091 100<br />
06251 114017 100<br />
05834 06046 05889 06061 06092 100<br />
05835 06252 05890 06287 06301 100<br />
05836 06253 05891 06288 06302 100<br />
05837 06254 05892 50<br />
05838 06255 05893 06303 50<br />
06256 114025 50<br />
06257 50<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
& Kwik Pak ®<br />
PART #00506<br />
Found on Page 48<br />
PART #00526<br />
Found on Page 49<br />
PART #00710<br />
Found on Page 50<br />
PART #00711<br />
Found on Page 50<br />
PART #00506KP<br />
Found on Page 49<br />
PART #00710KP<br />
Found on Page 50<br />
161<br />
FASTENERS
FASTENERS<br />
162<br />
Sheet Metal Screw <strong>Fasteners</strong><br />
Sheet Metal Screws<br />
DIA. LENGTH<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
#10 1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
#12 1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
#14 1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
3<br />
1/2<br />
3/4<br />
1<br />
5/16 1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
3/4<br />
1<br />
3/8 1-1/4<br />
1-1/2<br />
1-3/4<br />
PHILLIPS PHILLIPS PHILLIPS SLOTTED<br />
FLAT PAN OVAL HEX HEXWSHR. QTY.<br />
HEAD HEAD HEAD HEAD HEAD<br />
114179 06290 06093 100<br />
05839 06047 05894 06062 06094 100<br />
05840 06258 05895 06291 06304 100<br />
05841 06048 05896 06063 06095 100<br />
05842 06259 05897 112826 100<br />
05843 06049 05898 06064 06096 100<br />
05844 06260 05899 06155 06097 50<br />
05845 06050 05900 06065 06098 50<br />
05846 06261 05901 50<br />
05847 06262 05902 06156 06305 50<br />
06263 50<br />
06264 50<br />
05848 06051 05903 06066 06306 100<br />
05849 06265 05904 06292 06307 100<br />
05850 06052 05905 06067 06099 100<br />
06266 06293 100<br />
05851 06053 05906 06068 06100 100<br />
05852 06267 05907 06157 06101 50<br />
05853 06054 05908 06069 06102 50<br />
05854 06268 05909 50<br />
05855 06269 05910 06070 06309 50<br />
06270 50<br />
06271 50<br />
05856 06055 05911 06071 06310 50<br />
05857 06273 06294 06311 50<br />
05858 06056 05913 06072 06312 50<br />
06274 06295 50<br />
05859 06057 05914 06073 06314 50<br />
05860 06275 05915 06296 06315 50<br />
05861 06058 05916 06074 06316 50<br />
05862 06276 06317 50<br />
05863 06277 05918 06075 06318 50<br />
112853 50<br />
06278 06158 06319 50<br />
06279 50<br />
06299 25<br />
06076 25<br />
06077 25<br />
06159 25<br />
06078 25<br />
112864 25<br />
06079 25<br />
06080 25<br />
06081 25<br />
06160 25<br />
06082 25<br />
112875 25<br />
1 800 458-4018 www.uzengprod.com
Thread Cutting Screws<br />
Type “F” Point<br />
• Cyanide hardened.<br />
• Cut their own threads.<br />
• Uni-Zinc plated to resist<br />
rust and corrosion.<br />
DIA. LENGTH PART # QTY.<br />
1/4 06121 100<br />
3/8 06122 100<br />
6-32 1/2 06123 100<br />
3/4 06173 100<br />
1 114257 100<br />
1/4 06124 100<br />
3/8 06125 100<br />
8-32 1/2 06126 100<br />
3/4 06127 100<br />
1 06174 100<br />
1/4 06128 100<br />
3/8 06129 100<br />
10-32 1/2 06130 100<br />
3/4 06131 100<br />
1 06132 100<br />
1/2 06161 100<br />
10-24 3/4 06162 10<br />
1 06163 100<br />
1/2 06133 100<br />
3/4 06134 100<br />
1/4-20 1 06135 100<br />
1-1/4 06136 50<br />
1-1/2 06137 50<br />
Thread Cutting Screw <strong>Fasteners</strong><br />
Slotted Pan Head Hex Washer Head<br />
Phillips Flat Undercut Head<br />
TYPE “F”<br />
DIA. LENGTH PART # QTY.<br />
12-24 1/2 07854 100<br />
DIA. LENGTH PART # QTY.<br />
6-32 3/4 114295 100<br />
3/8 114298 100<br />
8-32 1/2 114299 100<br />
1 114303 100<br />
3/8 114305 100<br />
10-24 1/2 114306 100<br />
3/4 114308 100<br />
1 114310 100<br />
1/2 114312 100<br />
12-24 3/4 114313 100<br />
1 114314 100<br />
1/2 06138 100<br />
5/8 06139 100<br />
1/4-20 3/4 06140 100<br />
1 06141 100<br />
1-1/4 06142 100<br />
1/2 06143 100<br />
5/16-18 3/4 06144 100<br />
1 06145 100<br />
3/4 06146 50<br />
3/8-16 1 06147 50<br />
1-1/4 06148 50<br />
1-1/2 06149 50<br />
Available in<br />
an Assortment<br />
PART # 00524<br />
Found on Page 51<br />
1 800 458-4018 www.uzengprod.com<br />
163<br />
FASTENERS
FASTENERS<br />
164<br />
Steel Wood Screw <strong>Fasteners</strong><br />
Steel Wood Screws<br />
• Zinc plated<br />
SLOTTED SLOTTED PHILLIPS<br />
DIA. LENGTH ROUND FLAT FLAT<br />
HEAD HEAD HEAD QTY.<br />
1/4 06320 100<br />
3/8 07601 06321 100<br />
1/2 07602 06322 07760 100<br />
5/8 116801 100<br />
#4 3/4 07603 06324 07761 100<br />
7/8 116803 100<br />
1 116804 100<br />
1-1/4 116805 100<br />
1-1/2 116806 100<br />
3/8 07604 06330 100<br />
1/2 07605 06331 07762 100<br />
5/8 07606 06332 07763 100<br />
3/4 07607 06333 07764 100<br />
#6 7/8 06334 07765 100<br />
1 07609 06335 07766 100<br />
1-1/4 07610 06336 07767 100<br />
1-1/2 07611 06337 07768 100<br />
1-3/4 116814 100<br />
2 116815 100<br />
1/2 116816 100<br />
5/8 116817 100<br />
3/4 116818 100<br />
7/8 116819 100<br />
#7 1 116820 100<br />
1-1/2 116822 100<br />
1-3/4 116823 100<br />
2 116824 100<br />
3/8 06342 100<br />
1/2 07612 06343 07769 100<br />
5/8 07613 06344 07770 100<br />
3/4 07614 06345 07771 100<br />
7/8 06346 07772 100<br />
1 07616 06347 07773 100<br />
#8 1-1/4 07617 06348 07774 100<br />
8- 1-1/2 07618 06349 07775 100<br />
32 1-3/4 07619 06350 07776 100<br />
2 07620 06351 07777 100<br />
2-1/4 06352 07778 100<br />
2-1/2 07622 06353 07779 100<br />
3-1/2 116837 100<br />
1 800 458-4018 www.uzengprod.com<br />
SLOTTED SLOTTED PHILLIPS<br />
DIA. LENGTH ROUND FLAT FLAT<br />
HEAD HEAD HEAD QTY.<br />
1/2 07624 06355 07781 100<br />
5/8 06356 07782 100<br />
3/4 07626 06357 07783 100<br />
7/8 07627 07784 100<br />
1 07628 06359 07785 100<br />
1-1/4 07629 06360 07786 100<br />
#10 1-1/2 07630 06361 07787 50<br />
1-3/4 07631 06362 07788 50<br />
2 07632 06363 07789 50<br />
2-1/4 112943 113053 116847 50<br />
2-1/2 07633 06365 07790 50<br />
3 07634 06367 07791 50<br />
3-1/2 112946 113056 116850 50<br />
3/4 07635 06370 07792 50<br />
7/8 07636 50<br />
1 07637 06372 07794 50<br />
1-1/4 07638 06373 07795 50<br />
1-1/2 07639 06374 07796 50<br />
#12 1-3/4 07640 06375 07797 50<br />
2 07641 06376 07798 50<br />
2-1/4 113064 116858 50<br />
2-1/2 07642 06378 07799 50<br />
3 07643 06380 07800 50<br />
3-1/2 112957 113067 116861 50<br />
4 116862 50<br />
3/4 06381 07801 50<br />
1 07645 06382 07802 50<br />
1-1/4 07646 06383 07803 50<br />
1-1/2 07647 06384 07804 50<br />
#14 1-3/4 07648 06385 07805 50<br />
2 07649 06386 07806 50<br />
2-1/4 113073 116870 50<br />
2-1/2 07650 06388 07807 50<br />
3 07651 06390 07808 50<br />
3-1/2 07652 06391 07809 50<br />
4 07653 06392 07810 50<br />
Available in<br />
an Assortment<br />
& Kwik Paks<br />
PART #00518<br />
Found on Page 51<br />
PART #00703<br />
Found on Page 52<br />
PART #00518KP<br />
Found on Page 51<br />
PART #00703KP<br />
Found on Page 52
Brass Wood Screws<br />
• Sharp leader points.<br />
• 100% pure brass.<br />
• Deep slots and Phillips drive.<br />
• Highest quality.<br />
• Available in round and flat heads.<br />
DIA. LENGTH SLTD. ROUND HD. SLTD. FLAT HD. PHIL. FLAT HD.<br />
PART # QTY PART # QTY PART # QTY<br />
#4<br />
#6<br />
#8<br />
*Non stock<br />
1/4<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
3/8<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
07710 100<br />
07711 100<br />
07712 100<br />
07713 100<br />
07714 100<br />
07715 100<br />
07716 100<br />
07717 100<br />
07718 100<br />
07719 100<br />
07720 100<br />
07721 100<br />
147407 100<br />
07722 100<br />
07723 100<br />
07724 100<br />
07725 100<br />
07726 100<br />
07727 100<br />
07728 100<br />
07729 100<br />
07730 100<br />
07731 100<br />
07732 100<br />
07660 100<br />
07661 100<br />
07662 100<br />
147748 100<br />
07663 100<br />
07664 100<br />
07665 100<br />
07666 100<br />
07667 100<br />
07668 100<br />
07669 100<br />
07670 100<br />
07671 100<br />
07672 100<br />
07673 100<br />
07674 100<br />
07675 100<br />
07676 100<br />
07677 100<br />
07678 100<br />
07679 100<br />
07680 100<br />
07681 100<br />
07682 100<br />
124190* 100<br />
124191* 100<br />
124192* 100<br />
124193* 100<br />
124194* 100<br />
124195* 100<br />
124196* 50<br />
124197* 50<br />
124198* 100<br />
124199 100<br />
124200* 100<br />
124201 100<br />
124202* 100<br />
124203 100<br />
124204 100<br />
124205* 50<br />
124206* 50<br />
124207* 50<br />
124208 100<br />
124209* 100<br />
124210 100<br />
124211* 50<br />
124212 50<br />
124213* 50<br />
124214 50<br />
124215* 25<br />
124216* 25<br />
124217* 25<br />
124218* 25<br />
Brass Wood Screw <strong>Fasteners</strong><br />
DIA. LENGTH SLTD. ROUND HD. SLTD. FLAT HD. PHIL. FLAT HD.<br />
PART # QTY PART # QTY PART # QTY<br />
#10<br />
#12<br />
#14<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/2<br />
3<br />
3-1/2<br />
4<br />
07733 100<br />
07734 100<br />
07735 100<br />
07736 100<br />
07737 100<br />
07738 100<br />
07739 50<br />
07740 50<br />
07741 50<br />
07742 50<br />
07743 50<br />
07744 50<br />
07745 50<br />
07746 50<br />
07747 50<br />
07748 50<br />
07749 50<br />
07750 50<br />
07751 50<br />
07752 50<br />
07753 50<br />
07754 50<br />
07755 50<br />
07756 50<br />
07757 50<br />
07758 50<br />
07683 100<br />
07684 100<br />
07685 100<br />
07686 100<br />
07687 100<br />
07688 100<br />
07689 50<br />
07690 50<br />
07691 50<br />
07692 50<br />
07693 50<br />
07694 50<br />
07695 50<br />
07696 50<br />
07697 50<br />
07698 50<br />
07699 50<br />
07700 50<br />
07701 50<br />
07702 50<br />
07703 50<br />
07704 50<br />
07705 50<br />
07706 50<br />
07707 50<br />
07708 50<br />
Available in<br />
an Assortment<br />
124219 50<br />
124220* 50<br />
124221 50<br />
124222* 50<br />
124223 50<br />
124224* 50<br />
124225 50<br />
124226* 25<br />
124227* 25<br />
124228* 25<br />
124229* 25<br />
124230* 10<br />
124231* 10<br />
124232 50<br />
124233 50<br />
124234 50<br />
124235 50<br />
124236* 25<br />
124237 25<br />
124238* 25<br />
124239* 10<br />
124240* 10<br />
124241* 10<br />
124242* 25<br />
124243 25<br />
124244 25<br />
124245 25<br />
124246* 25<br />
124247 25<br />
124248 10<br />
124249 10<br />
124250* 10<br />
124251* 10<br />
PART #00739<br />
Found on Page 52<br />
PART #124292<br />
Found on Page 53<br />
1 800 458-4018 www.uzengprod.com<br />
165<br />
FASTENERS
FASTENERS<br />
166<br />
Hex Head Lag Screw <strong>Fasteners</strong><br />
Hex Head Lag Screws<br />
• Sharp point for easier starting.<br />
• Hex Head for easier wrenching.<br />
• For use in wood and other soft materials.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
DIAMETER 1/4 5/16 3/8 1/2 5/8 3/4<br />
LENGTH PART# QTY. PART# QTY. PART# QTY. PART# QTY. PART# QTY. PART# QTY.<br />
1 07300 50 07313 50 07326 50<br />
1-1/4 07301 50 07314 50 07327 50<br />
1-1/2 07302 50 07315 50 07328 50 07341 25<br />
1-3/4 07303 50 07316<br />
2 07304 50 07317 50 07330 50 07342 25<br />
2-1/2 07305 50 07318 50 07331 50 07343 25<br />
3 07306 50 07319 50 07332 50 07344 25<br />
3-1/2 07307 50 07320 50 07333 50 07345 25<br />
4 07308 50 07321 50 07334 25 07346 25 07356 10<br />
4-1/2 07322 50 07335 25 07347 25 113278 20<br />
5 07310 50 07323 50 07336 25 07348 25<br />
5-1/2 07311 50 07324 50 07337 25 07349 25<br />
6 07325 50 07338 25 07350 25<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00827<br />
Found on Page 53
Pen-A-Drive Screws<br />
...with the patented point (U.S. PAT. NO. 3,942,405)<br />
Pen-A-Drive Screw <strong>Fasteners</strong><br />
This unique product, with it’s revolutionary hardened needle point, easily penetrates the work surface and then<br />
quickly and smoothly drives home! It makes ordinary sheet metal screws seem dull by comparison.<br />
Here's how easy it is...<br />
Get Ready!<br />
Using any 1/4" or 3/8" drill motor, insert any size<br />
PEN-A-DRIVE Screw in the magnetic chuck.<br />
Get Set!<br />
Press the screw against the work to immediately<br />
penetrate the surface.<br />
Go!<br />
Press the drill trigger and the PEN-A-DRIVE Screw<br />
is fully seated in an instant!<br />
Pen-A-Drive Screws are available in these popular sizes...<br />
All sizes have a uniform 1/4" Head Diameter<br />
PART # SCREW SIZE QTY.<br />
120791 6 x 3/8 100<br />
120793 7 x 1/2 100<br />
120802 8 x 1/2 100<br />
120804 8 x 3/4 100<br />
120805 8 x 1 100<br />
120810 8 x 1-1/2 100<br />
120812 8 x 2 100<br />
120814 10 x 1/2 100<br />
120817 10 x 3/4 100<br />
120819 10 x 1 100<br />
One Chuck Fits All Sizes!<br />
For maximum speed and efficiency, use this 1/4” magnetic chuck<br />
with all sizes of PEN-A-DRIVE SCREWS.<br />
PEN-A-DRIVE screws can<br />
be installed and removed<br />
with ordinary tools.<br />
PART# 90516 QTY. 1<br />
PEN-A-DRIVE SCREWS ARE EXCELLENT FOR USE IN MANY MATERIALS...<br />
USE THEM ANYWHERE YOU’D NORMALLY USE SHEET METAL OR WOOD SCREWS IN...<br />
Available in<br />
Assortments &<br />
Kwik Paks<br />
• SHEET METAL • WOOD • PLASTIC • COMPOSITION BOARD • MANY OTHERS<br />
PART # 120825<br />
Found on Page 54<br />
PART # 120825KP<br />
Found on Page 54<br />
1 800 458-4018 www.uzengprod.com<br />
167<br />
FASTENERS
FASTENERS<br />
168<br />
Kwik Drill <strong>Fasteners</strong><br />
Kwik Drill Self-Drilling Screws (Also known as “TEK” Screws)<br />
FOR USE IN...<br />
• Construction. • Uni-zinc plated to resist rust and corrosion.<br />
• Metal Buildings. • And all types of general maintenance uses.<br />
• Electrical.<br />
STARTS EXACTLY WHERE IT’S PLACED!<br />
Kwik Drill’s patented point-forming process distributes a thin web across the chisel point. This provides<br />
quicker starts and virtually eliminates slip damage, and there is less chance of binding or stall out.<br />
FASTENS IN ONE EASY OPERATION:<br />
It drills a hole, taps and fastens in steel up to 7/32" thick in less time than it takes normally<br />
to drill the hole. By drilling its own hole, a Kwik Drill screw produces the optimum hole size,<br />
resulting in better thread engagement and tighter fit.<br />
Use these magnetic chucks for easy installation<br />
of Hex Head Kwik Drill Screws. (1/4” shank)<br />
1/4" PART# 90516 5/16" PART# 90517 3/8" PART# 90518<br />
QUANTITY - 1 QUANTITY - 1 QUANTITY- 1<br />
MAINTENANCE LARGE USER<br />
PROGRAM PROGRAM<br />
PART # QTY PART # QTY SIZE DESCRIPTION HEX SIZE<br />
107884 100 107884B 10000 6 X 1/2 PHILLIPS PAN HEAD #2 POINT<br />
107885 100 107885B 10000 6 X 3/4<br />
119193 100 119193B 10000 6 X 1<br />
119194 100 119194B 10000 6 X 1-1/4<br />
119195 100 119195B 8000 6 X 1-1/2<br />
122001 100 122001B 10000 8 X 1/2<br />
122002 100 122002B 10000 8 X 3/4<br />
122003 100 122003B 8000 8 X 1<br />
06106 50 06106B 6000 8 X 1-1/4<br />
06107 50 06107B 5000 8 X 1-1/2<br />
119196 50 119196B 3500 8 X 2<br />
91544 50 91544B 8000 10 X 1/2 PHILLIPS PAN HEAD #3 POINT<br />
91545 50 91545B 7000 10 X 3/4<br />
91546 50 91546B 5000 10 X 1<br />
107886 50 107886B 5000 10 X 1-1/4<br />
91547 50 91547B 5000 10 X 1-1/2<br />
107887 50 107887B 3000 10 X 2<br />
119197 50 119197B 2500 10 X 2-1/2<br />
119198 50 119198B 2000 10 X 3<br />
119199 50 119199B 4000 12 X 3/4<br />
119200 50 119200B 3000 12 X 1<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
Assortments &<br />
Kwik Paks<br />
PART # 00525<br />
Found on Page 54<br />
PART # 00845<br />
Found on Page 55<br />
PART # 00525KP<br />
Found on Page 55<br />
PART # 00845KP<br />
Found on Page 55
Kwik Drill <strong>Fasteners</strong><br />
MAINTENANCE LARGE USER<br />
PROGRAM PROGRAM<br />
PART # QTY PART # QTY SIZE DESCRIPTION HEX SIZE<br />
119201 50 119201B 2500 12 X 1-1/4 PHILLIPS PAN HEAD #3 POINT<br />
119202 50 119202B 2000 12 X 1-1/2<br />
119203 25 119203B 2000 12 X 2<br />
119204 25 119204B 1500 12 X 2-1/2<br />
119205 25 119205B 1000 12 X 3<br />
119206 50 119206B 2800 14 X 3/4<br />
119207 50 119207B 2400 14 X 1<br />
119208 50 119208B 2000 14 X 1-1/4<br />
119209 50 119209B 1800 14 X 1-1/2<br />
119210 25 119210B 1500 14 X 2<br />
119211 25 119211B 1200 14 X 2-1/2<br />
119212 25 119212B 1000 14 X 3<br />
06103 50 06103B 10000 8 X 1/2 HEX WASHER HEAD #2 POINT 1/4<br />
06104 50 06104B 10000 8 X 3/4<br />
06105 50 06105B 8000 8 X 1<br />
119213 50 119213B 6000 8 X 1-1/4<br />
119214 50 119214B 5000 8 X 1-1/2<br />
119215 50 119215B 3500 8 X 2<br />
06108 50 06108B 9000 10 X 1/2<br />
122007 50 122007B 8000 10 X 5/8<br />
06109 50 06109B 7000 10 X 3/4 HEX WASHER HEAD #3 POINT 5/16<br />
06110 50 06110B 5000 10X 1<br />
06111 50 06111B 4000 10X 1-1/4<br />
06112 50 06112B 4000 10 X 1-1/2<br />
121990 50 121990B 3000 10 X 1-3/4<br />
121991 50 121991B 3000 10 X 2<br />
119216 50 119216B 2500 10 X 2-1/2<br />
119217 50 119217B 2000 10 X 3<br />
06113 50 06113B 4000 12 X 3/4<br />
06114 50 06114B 3000 12 X 1<br />
06115 50 06115B 2000 12 X 1-1/4<br />
06116 50 06116B 2000 12 X 1-1/2<br />
121992 50 121992B 2000 12 X 1-3/4<br />
121993 50 121993B 2000 12 X 2<br />
119218 25 119218B 1500 12 X 2-1/2<br />
119219 25 119219B 1500 12 X 3<br />
06117 50 06117B 3500 14 X 3/4<br />
06118 50 06118B 3000 14 X 1<br />
06119 50 06119B 2000 14 X 1-1/4<br />
06120 50 06120B 2000 14 X 1-1/2<br />
121994 25 121994B 2000 14 X 1-3/4<br />
121995 25 121995B 2000 14 X 2<br />
121996 25 121996B 1500 14 X 2-1/2<br />
121997 25 121997B 1500 14 X 3<br />
119220 25 119220B 1000 14 X 3-1/2<br />
119221 25 119221B 800 14 X 4<br />
119222 50 119222B 3000 12 X 1 HEX WASHER HEAD ASSEMBLED WITH 5/16<br />
119223 50 119223B 2500 12 X 1-1/4 NEOPRENE BONDED WASHER FOR<br />
119224 50 119224B 2000 12 X 1-1/2 LEAKPROOF APPLICATIONS WITH #3<br />
119225 25 119225B 1500 12 X 2 POINT<br />
119226 25 119226B 1000 12 X 2-1/2<br />
119227 25 119227B 1000 12 X 3<br />
122018 50 122018B 3000 14 X 3/4 3/8<br />
122019 50 122019B 2500 14 X 1<br />
122020 50 122020B 2000 14 X 1-1/4<br />
122021 50 122021B 1500 14 X 1-1/2<br />
119228 25 119228B 1500 14 X 2<br />
119229 25 119229B 1000 14 X 2-1/2<br />
119230 25 119230B 1000 14 X 3<br />
1 800 458-4018 www.uzengprod.com<br />
169<br />
FASTENERS
FASTENERS<br />
170<br />
Crimp Plus Screw <strong>Fasteners</strong><br />
“Crimp Plus” Slotted Hex Washer Head Drill Screws<br />
Designed For Use In Thin Metals<br />
Performance<br />
<strong>Engineered</strong><br />
<strong>Fasteners</strong><br />
Shank Threaded Into Undercut<br />
Area Beyond Bearing Surface<br />
Reduces strip out. Permits use in thin materials.<br />
Special “Rust-Guard” Coating<br />
Provides extended resistance to effects<br />
of weather and guards against rusting. In<br />
testing, parts withstood 500 hours to red<br />
rust. Most standard zinc plated parts<br />
only withstand 72 hours.<br />
1 800 458-4018 www.uzengprod.com<br />
Serrated Washer Bearing Surface<br />
Resist vibration loosening by biting into base material.<br />
Higher seating torque when installed with a power tool.<br />
Available in<br />
an Assortment<br />
Undercut Washer Head<br />
Achieves high clamp force.<br />
Allows full diameter threads<br />
to remain engaged.<br />
BSD Spaced Thread Design<br />
In thin or porous materials such as sheet<br />
metal, wood and plastics, low strip-out is<br />
common and spaced threads are recommended.<br />
Self Drilling #2 Point. Drills Material Thickness Less Than .175"<br />
Eliminates separate drill and drive operations; combines both steps into one. Speeds<br />
assembly. Assures accurate and proper size hole for maximum thread engagement.<br />
DIAMETER 6-20 (1/4" Hex) DIAMETER 8-18 (1/4" Hex)<br />
LENGTH PART # QTY. LENGTH PART # QTY.<br />
1/2" 101942 50 1/2" 101944 50<br />
3/4" 101943 50 3/4" 101945 50<br />
1" 101946 50<br />
DIAMETER 10-16 (5/16" Hex) DIAMETER 12-14 (5/16" Hex)<br />
LENGTH PART # QTY. LENGTH PART # QTY.<br />
1/2" 101947 50 1/2" 101950 50<br />
3/4" 101948 50 3/4" 101951 50<br />
1" 101949 50 1" 101952 50<br />
DIAMETER 1/4-14 (3/8” Hex)<br />
LENGTH PART # QTY.<br />
1/2" 101953 50<br />
3/4" 101954 50<br />
1" 101955 25<br />
1-1/4” 105858 50<br />
1-1/2" 101956 25<br />
PART # 101959<br />
Found on Page 56
Crimp Plus Screw <strong>Fasteners</strong><br />
“Crimp Plus” Slotted Hex Washer Head Drill Screws<br />
How They Work<br />
Standard Sheet Metal Screw<br />
Strip-out occurs because shank root diameter<br />
increases and the major thread height decreases<br />
immediately under the head. Minimum thread<br />
engagement is the result, causing the fasteners<br />
to strip or spin-out at low torque values.<br />
<strong>UZ</strong> “Crimp Plus” <strong>Fasteners</strong><br />
The “Crimp Plus” head is undercut, allowing full<br />
diameter threads to remain engaged. Sheet metal<br />
is drawn up against the undercut head and held<br />
under tension, providing extra holding power and<br />
resistance to loosening and strip-out.<br />
Slip-Load Test<br />
A slip-load test designed to measure the force<br />
required to create shift in a fastened joint showed<br />
the <strong>UZ</strong> “Crimp Plus” provides greater clamp. A<br />
joint secured by a “Crimp Plus” fastener was able<br />
to withstand an average load four times greater<br />
than one secured by a serrated washer face screw.<br />
Magnetic Hex Driver Power Bits<br />
• 1/4" Hex Shank.<br />
• For use with <strong>UZ</strong> “Crimp Plus” Hex Washer Head Screws.<br />
• Precision formed for consistent dimensions.<br />
• <strong>Engineered</strong> for the toughest industrial applications.<br />
HEX SIZE OVERALL LENGTH PART # QTY.<br />
1/4" 1-5/8" 90516 1<br />
5/16" 1-5/8" 90517 1<br />
3/8" 1-3/4" 90518 1<br />
1 800 458-4018 www.uzengprod.com<br />
171<br />
FASTENERS
FASTENERS<br />
172<br />
Ultra – Fast Screw <strong>Fasteners</strong><br />
Ultra – Fast<br />
Multi-Purpose <strong>Fasteners</strong><br />
FEATURES:<br />
BENEFITS:<br />
•<br />
•<br />
•<br />
•<br />
•<br />
•<br />
•<br />
Optimized double-taper.<br />
Point geometry and patented.<br />
Ground serration in point threads.<br />
Improved head shape and recess geometry.<br />
High surface hardness and tough core.<br />
Universal application capability.<br />
Available in zinc plated steel or stainless steel.<br />
•<br />
•<br />
•<br />
Bites immediately and pulls fast into<br />
material without a pilot hole with less<br />
torque, and effort. Threads form easily<br />
and with greater holding power,<br />
requiring fewer fasteners.<br />
Improved bit fit, longer bit life and easier installation.<br />
Eliminates premature breakage.<br />
• Works in hard and soft wood chipboard, plywood,<br />
particle board, plastics, drywall, thin metals, and<br />
pre-drilled masonry.<br />
• Covers any indoor, outdoor, marine or corrosive<br />
environment applications.<br />
APPLICATIONS: (with no pre-drilling)<br />
• Hardwoods • Plastics • Chipboard • Particle Board<br />
• Softwoods • Composites • Plywoods<br />
• Drywall • Treated Lumber • Masonry (with pre-drilling)<br />
USED BY:<br />
• Hotels • Schools • Hospitals • Apartment Buildings<br />
• Woodworking Shops • Fleet • Industrial MRO • HVAC<br />
• Offices • Marinas • Parks & Recreation Departments<br />
DIAMETER LENGTH FLAT HEAD QTY. PAN HEAD QTY. FLAT HEAD QTY.<br />
ZINC ZINC STAINLESS<br />
3/4 91910 50 91926 50<br />
# 6 1 91927 50<br />
1-1/4 91912 25 91928 25 91945 50<br />
1-1/2 91929 25 91946 50<br />
3/4 91947 50<br />
# 8 1 91915 50 91932 50<br />
1-1/4 91916 25 91933 25 91949 25<br />
1-1/2 91934 25 91950 25<br />
1 91936 50<br />
# 10 1-1/4 91952 25<br />
1-1/2 91920 25 91953 25<br />
2 91921 25 91954 25<br />
2-1/2 91955 25<br />
1-1/2 91922 25<br />
# 14 2 91923 25 91941 25 91959 10<br />
Pozi-Drive Bits<br />
PART # QTY. DESCRIPTION<br />
91908 1 #2 x 2" POZI-DRIVE BIT<br />
91909 1 #3 x 2" POZI-DRIVE BIT<br />
91956 1 #2 x 1" POZI-DRIVE BIT<br />
91957 1 #3 x 1" POZI-DRIVE BIT<br />
1 800 458-4018 www.uzengprod.com
Dry Wall Screws<br />
#2 Phillips Head<br />
for easier<br />
driving.<br />
“Bugle head” style<br />
seats flush in dry wall<br />
without crushing<br />
or tearing.<br />
Black 0xide<br />
finish for greater<br />
resistance.<br />
Hardened steel for added strength<br />
Rugged threads<br />
for greater<br />
holding strength.<br />
• “Bugle” head design countersinks neatly.<br />
• Leaves behind a flat, smooth surface for easy finishing.<br />
• Won’t crush the gypsum core or tear paper.<br />
• Deep phillips recess.<br />
• Can be used with power tools for quick installation.<br />
• Rugged thread design - use in wood or laminated applications.<br />
• Special thread design provides excellent clamping strength and high vibration resistance.<br />
• Sharp point dimples steel at entry point.<br />
• Non-oily coarse, dry finish reduces call-backs due to “mud pops”.<br />
• Finish gives excellent corrosion resistance and improved joint compound adherence.<br />
Choose the program that’s best for you...<br />
Dry Wall Screw <strong>Fasteners</strong><br />
Sharp point<br />
for faster, easier<br />
penetration.<br />
DIA. LENGTH MAINT. MAINT. LARGE USER LARGE USER<br />
PART # QTY. PART # QTY. RECOMMENDED APPLICATIONS:<br />
#6 1" 121960 100 121980 5000 1/2" dry wall to metal studs. Steel channels wood to framing<br />
#6 1-1/8" 121961 100 Same as above, but when 5/8" dry wall is used<br />
#6 1-1/4" 121962 100 121982 4000 5/8" Dry wall into resilient channel and 1" core board.<br />
#6 1-5/8" 121963 100 121983 2500 Double layer of 5/8" dry wall to metal studs.<br />
#6 2" 121964 100 121984 1750 1/2" dry wall, core board and into metal studs.<br />
#6 2-1/4" 121965 100 121985 1500 Same as above, but when 5/8" dry wall is used.<br />
#8 1" 06495 100 1/2" dry wall to metal studs. Steel channels to wood framing.<br />
#8 1-1/4" 06496 100 5/8" dry wall into resilient channel and 1" core board.<br />
#8 1-5/8" 06497 100 Double layer of 5/8" dry wall to metal studs.<br />
#8 2-1/4" 06498 50 5/8" dry wall, core board and into metal studs.<br />
#8 2-1/2" 121966 50 121986 1250 5/8" dry wall through core to metal studs or channels.<br />
#8 3" 06499 50 121987 1000 5/8" dry wall through core to metal studs or channels.<br />
Available in<br />
an Assortment<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00586<br />
Found on Page 56<br />
173<br />
FASTENERS
FASTENERS<br />
174<br />
Security <strong>Fasteners</strong><br />
Ultra Security Screws<br />
• The U.S.A. - manufactured Ultra Security Screw has a 6-lope elliptical drive,<br />
providing the maximum protection of any security screw on the market today.<br />
• The Ultra Security Screw is made of 18/8 stainless steel, providing maximum<br />
corrosion resistance in indoor and outdoor applications, which eliminates the<br />
need for two separate types of fasteners.<br />
• Unlimited usage in both internal and external applications.<br />
• Made in the U.S.A.<br />
• ULTRA tamper-resistant security.<br />
• Reduces cost of replacing stolen equipment.<br />
• Corrosion resistant - can be used internally or externally.<br />
• Available in sheet metal screws and machine screws.<br />
• Any anti-theft application.<br />
INDUSTRIES AND APPLICATIONS:<br />
• Hotels • Hospitals • Shopping Malls • Computers<br />
• Schools • Industry • Recreational Facilities • Equipment<br />
• Fleets • Garages • Street and Sign Departments • Detention Facilities<br />
• Prisons • Door Jams • Racks and Accessories<br />
• Window Frames • Signs<br />
Button Head Sheet Metal Screw<br />
DIA. LENGTH PART # QTY.<br />
INSTALLATION<br />
BIT<br />
1/2 55131 40<br />
8<br />
3/4<br />
1<br />
55132<br />
55133<br />
40<br />
20<br />
55086<br />
T-20<br />
1-1/4 55134 20<br />
1/2 55135 40<br />
3/4 55136 40 55087<br />
10 1 55137 20 T-25<br />
1-1/4 55138 20<br />
1-1/2 55139 20<br />
1 800 458-4018 www.uzengprod.com<br />
Flat Head Sheet Metal Screw<br />
DIA. LENGTH PART # QTY.<br />
INSTALLTION<br />
BIT<br />
3/4 55140 40<br />
8 1 55141 20 55085<br />
1-1/4 55142 20 T-15<br />
3/4 55143 40<br />
10 1 55144 20 55086<br />
1-1/4 55145 20 T-20<br />
Available in<br />
an Assortment<br />
PART #00790<br />
Found on Page 56
Ultra Security Screws<br />
Button Head Machine Screws<br />
DIA. LENGTH PART # QTY.<br />
INSTALLATION<br />
BIT<br />
3/8 55089 40<br />
6-32 1/2 55090 40<br />
3/4 55091 40<br />
1 55092 20<br />
3/8 55093 40<br />
8-32 1/2 55094 40<br />
3/4 55095 40<br />
1 55096 20<br />
1/2 55097 40<br />
10-24 3/4 55098 40<br />
1 55099 20<br />
1-1/4 55100 20<br />
1/2 55101 40<br />
55084<br />
55084<br />
T10<br />
55085<br />
T15<br />
55087 55086<br />
T25<br />
10-32 3/4<br />
1<br />
55102<br />
55103<br />
40<br />
20<br />
55087<br />
T25<br />
1-1/4 55104 20<br />
1/2 55105 40<br />
1/4-20<br />
3/4<br />
1<br />
55106<br />
55107<br />
40<br />
20<br />
55088<br />
55088<br />
T27<br />
1-1/4 55108 20<br />
1-1/2 55109 20<br />
Available in<br />
an Assortment<br />
Security <strong>Fasteners</strong><br />
Flat Head Machine Screws<br />
DIA. LENGTH PART # QTY.<br />
INSTALLATION<br />
BIT<br />
3/8 55110 40<br />
6-32 1/2 55111 40<br />
3/4 55112 40<br />
1 55113 20<br />
3/8 55114 40<br />
8-32 1/2 55115 40<br />
3/4 55116 40<br />
1 55117 20<br />
1/2 55118 40<br />
10-24 3/4 55119 40<br />
1 55120 20<br />
1-1/4 55121 20<br />
1/2 55122 40<br />
Bit Set with Driver #55083<br />
includes all five bits and hand driver<br />
1 800 458-4018 www.uzengprod.com<br />
55084<br />
55084<br />
T10<br />
55085<br />
T15<br />
55087 55086<br />
T25<br />
10-32 3/4<br />
1<br />
55123<br />
55124<br />
40<br />
20<br />
55087<br />
T25<br />
1-1/4 55125 20<br />
1/2 55126 40<br />
1/4-20<br />
3/4<br />
1<br />
55127<br />
55128<br />
40<br />
20<br />
55088<br />
55088<br />
T27<br />
1-1/4 55129 20<br />
1-1/2 55130 20<br />
PART # 00788<br />
Found on Page 57<br />
PART # 00789<br />
Found on Page 57<br />
175<br />
FASTENERS
FASTENERS<br />
176<br />
Security <strong>Fasteners</strong><br />
Security Screws<br />
Spanner Pan Head Machine–18-8 Stainless Steel<br />
DIAMETER LENGTH PART # QTY.<br />
1/4 147530 25<br />
4-40 3/8 147531 25<br />
1/2 147532 25<br />
1/4 147533 25<br />
3/8 147534 25<br />
1/2 147535 25<br />
6-32 5/8 147536 25<br />
3/4 147537 25<br />
1 147538 25<br />
1-1/4 147539 25<br />
1-1/2 147540 25<br />
2 147541 25<br />
1/4 147542 25<br />
3/8 147543 25<br />
1/2 147544 25<br />
8-32 5/8 147545 25<br />
3/4 147546 25<br />
1 147547 25<br />
1-1/4 147548 25<br />
1-1/2 147549 25<br />
2 147550 25<br />
1/4 147551 25<br />
3/8 147552 25<br />
1/2 147553 25<br />
10-24 5/8 147554 25<br />
3/4 147555 25<br />
1 147556 25<br />
1-1/4 147557 25<br />
1-1/2 147558 25<br />
2 147559 25<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00416<br />
Found on Page 57<br />
Spanner Drivers Spanner Bits<br />
Spanner Bits attached Heat Treated<br />
DIA. PART # QTY DIA. PART # QTY.<br />
#4 147588 1 #4 147596 1<br />
#6 147589 1 #6 147597 1<br />
#8 147590 1 #8 147598 1<br />
#10 147591 1 #10 147599 1<br />
#12 147592 1 #12 147600 1<br />
1/4, 5/16, 3/8 147593 1 1/4 147601 1<br />
1/4 147594 1<br />
DIAMETER LENGTH PART # QTY.<br />
1/4 147560 25<br />
3/8 147561 25<br />
1/2 147562 25<br />
10-32 5/8 147563 25<br />
3/4 147564 25<br />
1 147565 25<br />
1-1/4 147566 25<br />
1-1/2 147567 25<br />
2 147568 25<br />
1/2 147569 25<br />
12-24 3/4 147570 25<br />
1 147571 25<br />
1-1/2 147572 25<br />
3/8 147573 25<br />
1/2 147574 25<br />
1/4-20 5/8 147575 25<br />
3/4 147576 25<br />
1 147577 25<br />
1-1/4 147578 25<br />
1-1/2 147579 25<br />
2 147580 25<br />
3/4 147581 25<br />
5/16-18 1 147582 25<br />
1-1/2 147583 25<br />
2 147584 25<br />
Spanner Magnetic Driver<br />
Bit Kit<br />
1 Magnetic Driver<br />
with 5 Spanner bits. Sizes 6, 8, 10,12, 1/4.<br />
PART # QTY.<br />
147602 1
Safeguard Non-Removable<br />
Aluminum Breakaway Nuts<br />
Ward off even the most determined thieves!<br />
• No special tool required–uses a<br />
standard wrench for installation.<br />
• Breakaway hex head accurately controls<br />
final torque (tightness) avoiding over<br />
torque and damage to the work surface.<br />
• The conical shaped security nut remains<br />
after break–off to resist tampering.<br />
APPLICATIONS:<br />
• Bathroom Fixtures • Security Cameras<br />
• Computers • Signs<br />
• Outdoor Lighting • Televisions Monitors<br />
• Playground Equipment<br />
DIAMETER PART # SIZE QUANTITY<br />
10-24 107104 7/16" Hex 25<br />
1/4-20 107105 9/16" Hex 25<br />
5/16-18 107106 6/8" Hex 25<br />
3/8-16 107107 3/4" Hex 25<br />
Ask your <strong>UZ</strong> Sales Associate about available assortments.<br />
Available in<br />
an Assortment<br />
Security <strong>Fasteners</strong><br />
Before After<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00781<br />
Found on Page 58<br />
177<br />
FASTENERS
FASTENERS<br />
178<br />
Thread Repair<br />
<strong>UZ</strong> Coil Thread Repair Inserts & Kits<br />
For Repairing Stripped or Damaged Threads (<strong>UZ</strong>’S Version of Helicoil ® )<br />
• <strong>UZ</strong> Coil has the most effective and universally accepted method of thread repair.<br />
• <strong>UZ</strong> Coil inserts quickly and permanently restore stripped, worn or damaged threads to their original size and condition<br />
Easy to use... Just 1. DRILL<br />
1 800 458-4018 www.uzengprod.com<br />
Just 2. TAP<br />
Just 3. INSTALL<br />
Now you're back to the original size and the original size fastener can be used.<br />
When threads become stripped, worn or damaged for any reason, the strength and reliability are<br />
greatly reduced. When this happens on critical threaded assemblies, cars, and other types of<br />
equipment, it may become unsafe to operate. These potentially dangerous situations are eliminated<br />
when the damaged thread is repaired with a <strong>UZ</strong> Coil screw insert. The <strong>UZ</strong> Coil threaded insert<br />
provides stronger, more reliable threads than the original tapped hole and at the same time eliminates<br />
the possibility of thread wear, seizing and corrosion.
Thread Repair<br />
INSTALLATION KITS REPLACEMENT INSERTS INSTALATION TAP REQUIRED DRILL<br />
INCLUDE INSERTS, INST. TOOL<br />
Thread Size and Length TOOL AND TAP SOLD IN PKGS SOLD IN PKGS<br />
INSERTS PKG OF ONE OF ONE SIZE KWIK CUT<br />
KIT NO PER KIT PART NO QTY PART NO PART NO NO<br />
USS COARSE THREAD All inserts made from 18-8 stainless steel<br />
10-24 x .285" 108481 10 108454 10 108506 108519 13/64 90148<br />
1/4-20 x .375" 108482 10 108455 10 108507 108520 17/64 90152<br />
5/16-18 x .469" 108483 10 108456 10 108508 108521 21/64 90156<br />
3/8-16 x .562" 108484 10 108457 10 108509 108522 25/64 90160<br />
7/16-14 x .656" 108485 5 108458 10 108510 108523 29/64 90164<br />
1/2-13 x .750" 108486 5 108459 10 108511 108524 17/32 100217*<br />
5/8-11 x .938" 108487 5 108460 5 108512 108525 21/32 100225*<br />
3/4-10 x 1.125" 108488 5 108461 5 108513 108526 25/32 100233*<br />
SAE FINE THREAD All inserts made from 18-8 stainless steel<br />
10-32 x .285" 108489 10 108462 10 108514 108527 13/64 90148<br />
1/4-28 x .375" 108490 10 108463 10 108507 108528 17/64 90152<br />
5/16-24 x .469" 108491 10 108464 10 108515 108529 21/64 90156<br />
3/8-24 x .562" 108492 10 108465 10 108516 108530 25/64 90160<br />
7/16-20 x .656" 108493 5 108466 10 108510 108531 29/64 90164<br />
1/2-20 x .750" 108494 5 108467 10 108512 108532 33/64 100216*<br />
METRIC REGULAR PITCH All inserts made from 18-8 stainless steel<br />
M6-1.00 x 9.0mm 108495 10 108468 10 108507 108533 1/4 90151<br />
M8-1.25 x 12.0mm 108496 10 108469 10 108515 108534 21/64 90156<br />
M9-1.25 x 13.5mm 108497 10 108470 10 108509 108535 "U 90161<br />
M10-1.5 x 15.0mm 108498 10 108471 10 108509 108536 13/32 90161<br />
M11-1.5 x 16.5mm 108499 5 108472 10 108510 108537 29/64 90164<br />
M12-1.75 x 18.9mm 108500 5 108473 5 108511 108538 31/64 90166<br />
METRIC FINE PITCH All inserts made from 18-8 stainless steel<br />
M10-1.25 x 15.0mm 108501 10 108474 10 108517 108539 13/32 90161<br />
M11-1.25 x 16.5mm 108502 10 108475 10 108510 108540 29/64 90164<br />
M12-1.50 x 18.0mm 108503 5 108476 5 108511 108541 31/64 90166<br />
M12-1.25 x 18.0mm 108504 5 108477 5 108511 108542 31/64 90166<br />
SPARK PLUG THREAD All inserts made from 18-8 stainless steel<br />
M14-125 x 3/8" short reach 1 108478 2 108518 108543 NO DRILL<br />
M14-1.25 x 1/2" med reach 108505 1 108479 2 108518 108543 USE TAP<br />
M14-1.25 x 3/4" long reach 1 108480 2 108518 108543 108543<br />
* = 1/2 REDUCED SHANK BIT<br />
1 800 458-4018 www.uzengprod.com<br />
179<br />
FASTENERS
FASTENERS<br />
180<br />
Thread Repair<br />
Keensert Thread Repair Inserts<br />
Strong, Permanent Thread Repairs In Minutes! Without Special Tools.<br />
FEATURES:<br />
• Install with standard drills and taps.<br />
• No pre-winder tool required.<br />
• Impossible to cross thread while installing.<br />
• Solid bushing with locking pins.<br />
• No tang break-off.<br />
• Positive mechanical lock against rotation.<br />
• May be used in virtually any material - aluminum, magnesium, cast iron, cold rolled<br />
steel and plastic.<br />
• Provide high strength and reliability. One length per size provides maximum pullout<br />
strength. Breaks Grade 8 bolts in test after test.<br />
• Easy to remove.<br />
• No special skills required. Installation procedures can be learned in minutes.<br />
• Many sizes available in Thinwall and Heavy Duty Thickwall. Metric sizes also available.<br />
Thinwall<br />
Inserts<br />
DIMENSIONS INSTALLATION DATA REMOVAL DATA<br />
INTERNAL TAP INSERT DRILL<br />
THREAD DRILL C’SINK TAP TOOL<br />
PART # QTY. SIZE LENGTH DIA. DIA. SIZE PART # SIZE DEPTH<br />
09998 5 10-24<br />
5/32<br />
09999 5 10-32 .31 “I” .32 5/16-18 09997 7/32<br />
10019 5 1/4-20<br />
10020 5 1/4-28 .37 “Q” .38 3/8-16 10374 9/32<br />
10021 5 5/16-18<br />
10022 5 5/16-24 .43 “X” .44 7/16-14 10375 11/32<br />
10023 5 3/8-16<br />
10024 5 3/8-24 .50 29/64 .51 1/2-13 10376 13/32 3/16<br />
10025 5 7/16-14<br />
10026 5 7/16-20 .56 33/64 .57 9/16-12 10377 15/32<br />
10027 5 1/2-13<br />
10028 5 1/2-20 .62 37/64 .63 5/8-11 10378 17/3<br />
* Recommended using Drill & Tap sizes as listed Kwik Cut drills on page 548<br />
Bottoming Taps on page 594<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00509<br />
Found on Page 58<br />
PART # 00519<br />
Found on Page 58<br />
PART # 00520<br />
Found on Page 59
Heavy Duty<br />
Thickwall<br />
Inserts<br />
For applications requiring higher<br />
pullout strengths or thread sizes<br />
exceeding 1/2".<br />
DIMENSIONS INSTALLATION DATA REMOVAL DATA<br />
INTERNAL TAP INSERT DRILL<br />
THREAD DRILL C’SINK TAP TOOL<br />
PART # QTY. SIZE LENGTH DIA. DIA. SIZE PART # SIZE DEPTH<br />
10000 5 8-32 .31 “I” .32 5/16-18 10379 7/32<br />
10001 5 10-24 1/8<br />
10002 5 10-32 .31 “Q” .38 3/8-16 10380 9/32<br />
10003 5 1/4-20<br />
10004 5 1/4-28 .37 “X” .44 7/16-14 10381 11/32<br />
10005 5 5/16-18<br />
10006 5 5/16-24 .43 29/64 .51 1/2-13 10382 13/32<br />
10007 5 3/8-16<br />
10008 5 3/8-24 .50 33/64 .57 9/16-12 10383 15/32<br />
10009 5 7/16-14 3/16<br />
10010 5 7/16-20 .62 37/64 .63 5/8-11 10384 17/32<br />
10011 5 1/2-13<br />
10012 5 1/2-20 .62 45/64 .76 3/4-16 10385 21-32<br />
10013 5 9/16-12<br />
10014 5 9/16-18 .81 45/64 .76 3/4-16 10386 21-32<br />
10015 5 5/8-11<br />
10016 5 5/8-18 .87 53/64 .88 7/8-14 10387 25/32<br />
10017 5 3/4-10<br />
10018 5 3/4-16 1.12 1-1/16 1.14 1-1/8-12 10388 31-32<br />
10370 2 7/8-9<br />
10371 2 7/8-14 1.25 1-3/16 1.27 1-1/4-12 10389 1-3/32<br />
10372 2 1-8<br />
10373 2 1-14 1.37 1-5/16 1.39 1-3/8-12 10390 1-7/32 5/16<br />
121300 1 1-1/8-7<br />
121316 1 1-1/8-12 1.62 1-7/16 1.52 1-1/2-12 121332 1-11/32<br />
121301 1 1-1/4-7<br />
121317 1 1-1/4-12 1.81 1-9/16 1.64 1-5/8-12 121333 1-15/32<br />
121302 1 1-1/2-6<br />
121318 1 1-1/2-12 2.00 1-13/16 1.89 1-7/8-12 121334 1-23/32<br />
Keensert Material: C1215 Steel or Equivalent. Threads Manufactured to MIL-S-7742<br />
Keensert Driver Tools Economy Driver Tool<br />
Individual tools for thinwall and Use with all Keenserts up to 9/16” diameter.<br />
thickwall sizes. Consult chart Set Keenserts using ordinary hammer.<br />
for part numbers. PART # 10029 - QTY. 1<br />
All tools Qty. 1<br />
Thread Repair<br />
1 800 458-4018 www.uzengprod.com<br />
181<br />
FASTENERS
FASTENERS<br />
182<br />
Thread Repair<br />
TYPICAL APPLICATION:<br />
• Automobiles • Tooling • Buses<br />
• Power Tools • Trucks • Recreational Vehicles<br />
• Heavy Equipment • Small Engines • Marine Equipment<br />
Quick, Easy to Install with Standard Tools...<br />
1. Use Standard Drill 2. Use Standard Tap 3. Screw in Keensert. 4. Drive locking Kees 5. It's... that easy!<br />
to drill out damaged to thread new hole. Kees automatically stop with light taps on<br />
threads. Then, counter- the insert at its correct tool.<br />
sink with a standard location.<br />
countersink.<br />
Quick, Easy to Remove... IF Necessary... with Standard Tools...<br />
1. Use Standard Drill to 2. Deflect Kees inward 3. Remove insert with 4. An identical insert can<br />
remove insert material and break off. EZ-OUT type tool. now be installed in the<br />
original hole.<br />
Keenserts can be removed without damage to the parent material if required.<br />
An identical replacement insert can then be installed into the original tapped hole.<br />
1 800 458-4018 www.uzengprod.com
Metric Keenserts For Metric Thread Repairs<br />
All Dimensions In Inches Unless Noted. Metric Keensert Installation Tools All Package QTY. 1<br />
DIMENSIONS INSTALLATION DATA REMOVAL DATA<br />
INTERNAL INSERT DRILL<br />
THREAD DRILL C’SINK TAP TOOL<br />
PART # QTY. SIZE LENGTH DIA. DIA. SIZE PART # SIZE DEPTH<br />
09900 5 M3 x 0.5 4.25mm 4.4mm 5.1mm M5 x .8 09918 3.5mm 2.25mm<br />
09901 5 M4 x 0.7 5.25mm 5.5mm 6.1mm M6 x 0.75 09919 4.6mm 2.5mm<br />
09902 5 M5 x 0.8 .315 H .32 M8 x 1.25 09920 7/32 5/32<br />
09903 5 M6 x 1.0 .394 S .40 M10 x 1.25 09921 19/64 3/16<br />
09904 5 M7 x 1.0 .433 W .44 M11 x 1.0 09922 Q 3/16<br />
09905 5 M8 x 1.0 .472 27/64 .48 M12 x 1.25 09923 3/8 3/16<br />
09906 5 M8 x 1.25 .472 27/64 .48 M12 x 1.25 09923 3/8 3/16<br />
09907 5 M10 x 1.25 .551 1/2 .56 M14 x 1.5 09924 29/64 3/16<br />
09908 5 M10 x 1.50 .551 1/2 .56 M14 x 1.5 09924 29/64 3/16<br />
09909 5 M12 x 1.25 .630 37/64 .63 M16 x 1.5 09925 17/32 3/16<br />
09910 5 M12 x 1.75 .630 37/64 .63 M16 x 1.5 09925 17/32 3/16<br />
09911 2 M14 x 1.5 .787 47/64 .79 M20 x 1.5 09926 11/16 3/16<br />
09912 2 M14 x 2.0 .787 47/64 .79 M20 x 1.5 09926 11/16 3/16<br />
09913 1 M16 x 1.5 .866 13/16 .87 M22 x 1.5 09927 45/64 3/16<br />
09914 1 M18 x 1.5 .945 57/64 .95 M24 x 1.5 09928 28/32 3/16<br />
09915 1 M20 x 1.5 1.181 1-7/64 1.18 M30 x 2.0 09929 1-1/64 1/4<br />
09916 1 M22 x 1.5 1.260 1-3/16 1.26 M32 x 2.0 09930 1-3/32 1/4<br />
09917 1 M24 x 2.0 1.299 1-7/32 1.27 M33 x 2.0 09931 1-1/8 1/4<br />
Available in<br />
an Assortment<br />
Thread Repair<br />
PART # 00995<br />
Found on Page 59<br />
PART #00345<br />
Found on Page 59<br />
1 800 458-4018 www.uzengprod.com<br />
183<br />
FASTENERS
FASTENERS<br />
184<br />
Thread Repair<br />
Woodsert ®<br />
• External knife threads provide superior holding power in hard and soft woods,<br />
particle board and all wood products.<br />
• Use wherever field assembly could lead to thread erosion or stripping.<br />
• The long pilot assures straight driving into a drilled hole.<br />
• Sizes up to #10 are easily installed with an ordinary screwdriver, or a hexagon screw<br />
and wrench. A woodsert driver tool is recommended for installing sizes #12 and larger.<br />
• Made in the U.S.A.<br />
• All steel construction.<br />
• Ultra-Zinc plated to resist rust and corrosion.<br />
• Excellent pullout strength.<br />
Hundreds of maintenance uses!<br />
• Hinge Plates • Furniture Repair • Partitions • Railings<br />
• Mounting Shelving or Fixtures to Wood Studs and many others...<br />
Easy to install!<br />
1. Drill proper diameter hole. 2. Seat Woodsert with ordinary screw 3. Installed! Mount fixture, etc., using<br />
(Drill slightly deeper than overall driver or Woodsert Driver Tool. your choice of Thread <strong>Fasteners</strong>.<br />
length of Woodsert) (Cap Screw or Machine Screw)<br />
INTERNAL HOLE O.D.<br />
THREAD SIZE OVERALL DIAMETER OUTSIDE<br />
PART # (SCREW/BOLT SIZE) QTY. LENGTH (DRILL SIZE) DIAMETER<br />
10358 4-40 NC 25 3/8 1/4 21/64<br />
10359 6-32 NC 25 3/8 1/4 21/64<br />
10360<strong>UZ</strong> 8-32 NC 25 3/8 1/4 21/64<br />
10361<strong>UZ</strong> 10-24 NC 25 1/2 3/8 29/64<br />
10362 10-32 NF 25 1/2 3/8 29/64<br />
10369 12-24 NC 25 1/2 3/8 29/64<br />
10363 1/4-20 NC 25 1/2 3/8 29/64<br />
10364 1/4-28 NF 25 1/2 3/8 29/64<br />
10365 5/16-18 NC 25 5/8 1/2 19/32<br />
10366 5/16-24 NF 25 5/8 1/2 19/32<br />
10367 3/8-16 NC 25 5/8 1/2 19/32<br />
10368 3/8-24 NF 25 5/8 1/2 19/32<br />
10391 1/2-13 NC 10 3/4 3/4 57/64<br />
Woodsert Driver Tools<br />
For easy installation of<br />
Woodsert sizes #12 and larger<br />
1 800 458-4018 www.uzengprod.com<br />
PART # INTERNAL<br />
THREAD<br />
10392 #12<br />
10393 1/4<br />
10394 5/16<br />
10395 3/8<br />
10396 1/2<br />
Example of a woodsert<br />
In a hinge application.<br />
Available in<br />
an Assortment<br />
PART # 00500<br />
Found on Page 59
Tric-Nut<br />
Threaded Steel Inserts<br />
• An insert with strong, permanent steel threads for use in blind, buried, and through holes in most any material.<br />
• Reduces overall length of the installed TRIC-NUT allows it to be used in limited clearance applications.<br />
• Works in any thickness over .030" (Equivalent to 22ga. sheet metal).<br />
• Can be used with Grade 8/Metric 10.9 screws due to TRIC-NUTS high shear load capacity.<br />
• Nearly flush installation resists vibration and self-tightens with repeated use.<br />
How they work:<br />
The installation tool pulls the cone-shaped nut portion into the sleeve expanding it into the parent material.<br />
The Axial knurl under the flange is then forced into the parent material insuring superior torque-out resistance.<br />
TRIC-NUTS are versatile, can be used in many types of applications in almost any material.<br />
Thick or thin Flat or curved<br />
(.030 MIN)<br />
Blind, Buried or though holes<br />
MATERIAL THICKNESS TO DRILL SIZE<br />
THREAD .030-.090 .091-.120 .125-.186 .187 & OVER QTY.<br />
PART # SIZE DRILL DRILL DRILL DRILL<br />
10038 4-40 3/16 #10 #10 #9 50<br />
10039 6-32 7/32 #2 #1 #1 50<br />
10040 8-32 1/4 “F” 17/64 17/64 50<br />
10041 10-24 9/32 “L” “L” 19/64 50<br />
10042 10-32 9/32 “L” “L” 19/64 50<br />
09995 12-24 3/8 3/8 “W” 25/64 25<br />
10043 1/4-20 3/8 3/8 “W” 25/64 25<br />
10044 1/4-28 3/8 3/8 “W” 25/64 25<br />
10045 5/16-18 1/2 1/2 33/64 33/64 25<br />
10046 5/16-24 1/2 1/2 33/64 33/64 25<br />
10047 3/8-16 9/16 9/16 37/64 37/64 25<br />
10048 3/8-24 9/16 9/16 37/64 37/64 25<br />
10049 M3 x 0.5 3/16 #10 #10 #9 25<br />
10050 M4 x 0.7 1/4 “F” 17/64 17/64 25<br />
10051 M5 x 0.8 9/32 “L” “L” 19/64 25<br />
10052 M6 x 1.0 3/8 3/8 “W” 25/64 25<br />
10053 M8 x 1.25 1/2 1/2 33/64 33/64 25<br />
10054 M10 x 1.5 9/16 9/16 37/64 34/64 25<br />
* Recommended using Kwik Cut drills on page xxx<br />
Thread Repair<br />
MANY POSSIBLE APPLICATIONS INCLUDING:<br />
• Trucks and Bus Bodies • Vending Machines • Appliances • Fiberglass Boats<br />
• Overhead Doors • Aircraft Maintenance • Bins and Shelves • Recreational Vehicles<br />
• Lighting Fixtures • Air Conditioning Equipment<br />
1 800 458-4018 www.uzengprod.com<br />
185<br />
FASTENERS
FASTENERS<br />
186<br />
Thread Repair<br />
Grip-Sert<br />
Threaded Inserts<br />
With Double Locking Action<br />
This highly versatile insert delivers the highest torque-out and high pull-out<br />
values in sheet metal, structural foam, fiberglass, and some plastics.<br />
FEATURES:<br />
• Install in a wide variety of materials from .020 to .165 inches thick.<br />
• Large head allows applications where oversize or irregular holes might be a problem.<br />
• High torque-out values resists spinning due to cross-threading or over-tightening.<br />
• “Bubble” on backside resists pull-out.<br />
• Blind installation - no access to the backside required.<br />
• Installs easily with the lever action tool # 90044 and appropriate conversion kit.<br />
• Plated to QQ-P-416 TYPE II CLASS 2 Specs for protection 40 times better than zinc.<br />
• Exceptional torque strength is achieved as the GRIP-SERT’s knurled<br />
body expands filling the hole.<br />
• Offers highest all around strength characteristics and has been designed<br />
to be used with Grade 5 or Metric 8.8/10.9 screws.<br />
INSERT THREAD GRIP DRILL CONV. KIT<br />
PART # SIZE RANGE SIZE QTY. PART #<br />
91622 6-32 .020-.080 17/64 50 90035<br />
91623 8-32 .020-.080 17/64 50 90036<br />
91624 10-24 .020-.130 19/64 50 90037<br />
91625 10-32 .020-.130 19/64 50 90038<br />
91626 1/4-20 .027-.165 25/64 25 90039<br />
91627 1/4-28 .027-.165 25/64 25 90040<br />
91628 5/16-18 .027-.150 17/32 25 90041<br />
91629 5/16-24 .027-.150 17/32 25 90042<br />
91630 3/8-16 .027-.150 17/32 25 90032<br />
91631 3/8-24 .027-.150 17/32 25 90033<br />
91903 M4-0.7 0,50-2,00 6,75 25 90028<br />
91904 M5-0.8 0,50-3,30 7,60 25 90029<br />
91905 M6-1.0 0,70-4,20 10,00 25 90030<br />
91906 M8-1.25 0,70-3,8 13,50 25 90031<br />
91907 M10-1.50 0,70-3,8 13,50 25 90034<br />
APPLICATIONS:<br />
APPLIANCES: MEDICAL EQUIPMENT:<br />
• Refrigerator Handle to Door. • Wheelchair Hand Rims.<br />
• Components to Cabinet. • Components to Hospital Beds.<br />
• Under the Counter Attachments. • Aluminum Walker Assembly.<br />
FURNITURE: HEATING/AIR CONDITIONING:<br />
• Aluminum Furniture Assembly. • Compressors to Base Pan.<br />
• Patio Table Assembly. • Motors to Blower Housing.<br />
• Brass Headboard to Frame.<br />
• ...And Many More!<br />
• Access Doors to Cabinet.<br />
1 800 458-4018 www.uzengprod.com<br />
AXIAL<br />
KNURLING<br />
BEFORE INSTALLATION:<br />
Note the long band of axial knurling on every<br />
insert. This unique design feature is one of the<br />
keys to GRIP-SERT’s exceptional strength.<br />
The knurled body expands 360° filling the hole.<br />
Available in<br />
an Assortment<br />
Here’s Why:<br />
AFTER INSTALLATION:<br />
See how GRIP-SERT not only grips the surface<br />
on the inside of the hole, but has folded over<br />
and formed a “bubble” that firmly grips a wide<br />
surface underneath. This results in high resistance<br />
to spinning and increased pull-out valves.<br />
PART # 00761<br />
Found on Page 60<br />
PART # 00762<br />
Found on Page 60<br />
PART # 00763<br />
Found on Page 60<br />
PART # 00764<br />
Found on Page 61<br />
PART # 00765<br />
Found on Page 61
TSN Insert and Tric-Nut<br />
Installation Tools<br />
Lever Hand Tool<br />
PART # 90044 QTY. 1<br />
This tool is designed for the manual installation<br />
of Grip-Serts, Tric-Nuts and TSN Inserts. It<br />
functions in a similar manner to that of a<br />
breakstem rivet hand tool. With simple set-up<br />
and in a single, uniform stroke, this tool<br />
consistently sets inserts. Extra long handles<br />
for added leverage allow the inserts to be placed<br />
with minimal effort. High strength formed steel<br />
construction eliminates the inherent weakness<br />
of cast parts.<br />
Tool Kit<br />
PART # 90043 QTY. 1<br />
Each tool kit contains one lever hand tool and<br />
conversion kits for the 6-32, 8-32, 10-32,10-24,<br />
1/4-20 and 5/16-18 Threaded Inserts.<br />
T-Handle Tool<br />
PART # 90062 QTY. 1<br />
Install TSN’s, Tric-Nuts, and Grip-Serts.<br />
LEVER TOOL<br />
CONVERSION KITS<br />
NOSEPIECE<br />
MANDREL<br />
T-HANDLE TOOL<br />
CONVERSION KITS<br />
NOSEPIECE<br />
MANDREL<br />
Thread Repair<br />
PART # THREAD SIZE QTY.<br />
90027 M3 x 0.5 1<br />
90028 M4 x 0.7 1<br />
90029 M5 x 0.8 1<br />
90030 M6 x 1.0 1<br />
90031 M8 x 1.25 1<br />
90034 M10 x 1.5 1<br />
90004 4-40 1<br />
90035 6-32 1<br />
90036 8-32 1<br />
90037 10-24 1<br />
90038 10-32 1<br />
90025 12-24 1<br />
90039 1/4-20 1<br />
90040 1/4-28 1<br />
90041 5/16-18 1<br />
90042 5/16-24 1<br />
90032 3/8-16 1<br />
90033 3/8-24 1<br />
Instructions for tool can be found in the Technical Section.<br />
PART # THREAD SIZE QTY.<br />
90045 4-40 1<br />
90046 6-32 1<br />
90047 8-32 1<br />
90048 10-24 1<br />
90049 10-32 1<br />
120774 12-24 1<br />
90050 1/4-20 1<br />
90051 1/4-28 1<br />
90052 5/16-18 1<br />
90053 5/16-24 1<br />
90054 3/8-16 1<br />
90055 3/8-24 1<br />
90056 M3 x 0.5 1<br />
90057 M4 x 0.7 1<br />
90058 M5 x 0.8 1<br />
90059 M6 x 1.0 1<br />
90060 M8 x 1.25 1<br />
90061 M10 x 1.5 1<br />
1 800 458-4018 www.uzengprod.com<br />
187<br />
FASTENERS
FASTENERS<br />
188<br />
Thread Repair<br />
<strong>UZ</strong> EZ Insert Installation Tool<br />
The only Threaded Insert hand tool you'll ever need!<br />
Tired of buying multiple tools to install different styles of threaded inserts?<br />
<strong>UZ</strong> presents a hand installation tool, capable of handling all styles of rivet<br />
nuts/threaded inserts from 6-32 to 3/8-16 and M3 to M10.<br />
Installations can be difficult using Lever Hand tools on large size inserts. This<br />
new tool uses the torque provided from a ratchet and wrench to make the job<br />
quick and easy - not matter what size insert you have.<br />
All tools have the same body size, thereby requiring only one 11/16" ratchet<br />
and one 7/8" wrench to install all sizes and styles of rivet nuts/threaded inserts.<br />
Each tool is marked for easy identification.<br />
In addition, this hand installation tool uses a standard socket head cap screw<br />
as a mandrel, making replacement convenient and economical.<br />
Easy to follow instructions:<br />
USS PART # SAE PART # METRIC PART #<br />
6-32 114274 M3 114284<br />
8-32 114275 M4 114285<br />
10-24 114276 10-32 114277 M5 114286<br />
1/4-20 114278 1/4-28 114279 M6 114287<br />
5/16-18 114280 5/16-24 114281 M8 114288<br />
3/8-16 114282 3/8-24 114283 M10 114289<br />
1 800 458-4018 www.uzengprod.com<br />
NEW!<br />
1. Thread rivet nut onto the tool. 2. Place rivet nut into the hole. 3. Hold the bottom nut (closest<br />
to the rivet) with a 7/8"<br />
wrench and turn the top nut<br />
with an 11/16" socket<br />
clockwise.<br />
(All PK QTY: 1)<br />
4. When rivet nut is set, reverse<br />
wrench 1/4 turn to break<br />
tension and remove screw.
<strong>UZ</strong> Rapid Drive Anchors<br />
Screw and Anchor in One<br />
For light to medium duty anchoring<br />
The New <strong>UZ</strong> Rapid Drive Anchor is an all-steel one-piece screw anchor, which features<br />
high profile threads for easy fastening into wallboard and other masonry base<br />
materials.<br />
Its deep cutting corkscrew-like threads provide for smooth entry and a powerful hold,<br />
and when removed the <strong>UZ</strong> Rapid-Drive Anchor leaves a much smaller hole than toggles<br />
or other systems. For aesthetic appearances, the <strong>UZ</strong> Rapid-Drive Anchor is<br />
available in two color finishes: white and chrome; and in two head styles: pan and<br />
oval.<br />
For fastening into wallboard or wood, no pre-drilling is required, the anchor is inserted<br />
through the fixture and screwed in with an ordinary Phillips screwdriver. Fastening<br />
into concrete, hollow or grout filled block, brick and plaster requires a pre-drilled<br />
3/16" ANSI hole.<br />
FEATURES BENEFITS<br />
High Profile threads Powerful hold, clean cutting and smooth entry<br />
Prevents spinning and stripping<br />
Heat Treated Point Penetrates both metal and wood studs<br />
Self-drilling in wallboard and wood Can install with fixture in place<br />
Removable Leaves a much smaller hole than toggles<br />
White or Chrome finish Matches any décor<br />
SUITABLE BASE MATERIALS<br />
Anchor <strong>Fasteners</strong><br />
Wallboard Plywood Concrete Hollow or grout Brick Plaster<br />
Filled Block<br />
APPLICATIONS<br />
Electrical Fixtures<br />
Thermostats<br />
HVAC Fixtures<br />
Plumbing Fixtures<br />
Telecommunications<br />
Equipment<br />
Bathroom Accessories<br />
Shelving & Supports<br />
Mirrors<br />
Chalk & White Boards<br />
PART # DESCRIPTION PKG QTY<br />
113559 Phillips Oval Head Chrome 20<br />
113560 Phillips Oval Head White 20<br />
113561 Phillips Pan Head Chrome 20<br />
113562 Phillips Pan Head White 20<br />
Size Range: 3/16" Diameter hole x 1-1/4" Length<br />
Anchor Material: Case Hardened Steel<br />
Picture Frames<br />
Brackets<br />
Plaques & Awards<br />
Smoke Detectors<br />
Available in<br />
a Kwik Pak<br />
PART # 00455KP<br />
Found on Page 62<br />
PART # 00474<br />
Found on Page 61<br />
1 800 458-4018 www.uzengprod.com<br />
189<br />
FASTENERS
FASTENERS<br />
190<br />
Anchor <strong>Fasteners</strong><br />
<strong>UZ</strong> Rapid Drive Anchor Technical Data<br />
Ultimate Load Capacities - Wallboard & Plywood<br />
Anchor Diameter<br />
In.(mm)<br />
1/4 (6.4)<br />
Ultimate Load Capacities - Normal Weight Concrete<br />
Anchor Diameter<br />
In.(mm)<br />
1/4 (6.4)<br />
1/2" Wallboard 5/8" Wallboard 1/2" Plywood<br />
Embedment Depth In.(mm)<br />
3/4 (19.1)<br />
1(25.4)<br />
1 800 458-4018 www.uzengprod.com<br />
Minimum Concrete Compressive Strength<br />
F'c>4000 psi (27.6 Mpa)<br />
Tension Lbs.(kN) Shear lbs.(kN)<br />
350 (1.6) 1,030 (4.6)<br />
700 (3.2) 1,070 (4.8)<br />
Ultimate Load Capacities - Grout Filled & Hollow Concrete Masonry & Structural Brick Masonry<br />
Anchor Diameter<br />
In.(mm)<br />
1/4 (6.4)<br />
Tension Lbs.(kN)<br />
85 (0.4)<br />
Embedment<br />
Depth In.(mm)<br />
3/4 (19.1)<br />
3/4 (19.1)<br />
1(25.4)<br />
1(25.4)<br />
Shear lbs.(kN)<br />
245 (1.1)<br />
Anchor<br />
Location<br />
Center of<br />
Masonry Unit<br />
T-Joint<br />
Center of<br />
Masonry Unit<br />
T-Joint<br />
Tension Lbs.(kN)<br />
135 (0.6)<br />
Grout filled CMU<br />
ASTM C-90 Block<br />
Tension<br />
Lbs.(kN)<br />
-<br />
-<br />
305 (1.4)<br />
290 (1.3)<br />
Shear<br />
lbs.(kN)<br />
-<br />
-<br />
825 (3.7)<br />
915 (4.1)<br />
Shear lbs.(kN)<br />
360 (1.6)<br />
Hollow CMU<br />
ASTM C-90 Block<br />
Tension<br />
Lbs.(kN)<br />
-<br />
-<br />
305 (1.4)<br />
290 (1.3)<br />
Tension Lbs.(kN)<br />
255 (1.1)<br />
Shear<br />
lbs.(kN)<br />
1 800 458-4018 www.uzengprod.com<br />
-<br />
-<br />
825 (3.7)<br />
915 (4.1)<br />
Structural Brick<br />
Masonry<br />
F'm>1500 psi<br />
(10.3 Mpa)<br />
Tension<br />
Lbs.(kN)<br />
400 (1.8)<br />
350 (1.6)<br />
600 (2.7)<br />
380 (1.7)<br />
Shear lbs.(kN)<br />
600 (2.7)<br />
Shear<br />
lbs.(kN)<br />
650 (2.9)<br />
600 (2.9)<br />
900 (4.1)<br />
825 (3.7)
Quadlock Anchors<br />
Temperature Range<br />
-50° to 180° F (-50° to 80° C)<br />
Screw<br />
Cuts its own thread for<br />
maximum holding power<br />
INSTALLATION:<br />
Drill the hole in accordance with the table and install the plug.<br />
In plasterboard, make a hole using a drill or an awl. The hole<br />
should be a press fit for the plug.<br />
Fix with a screw long enough to penetrate through the whole<br />
length of the plug and fixture.<br />
The mounting is ready, and the screw has expanded the plug<br />
in the correct way.<br />
FEATURES:<br />
• No critical drilling depth - works well at<br />
minimum depth and beyond.<br />
• Firm collar eliminates cracks in plaster walls<br />
and does not disappear into hollow block.<br />
• Collar is soft enough to counter sink the<br />
anchor when mounting through tiles.<br />
• Double expanding<br />
• Recognizable color code<br />
• Easy to install<br />
• High load values<br />
• Self-centering design for screw<br />
Firm collar<br />
Keeps anchor in place and eliminates fall-through<br />
Anchor <strong>Fasteners</strong><br />
Specially designed fins<br />
Eliminate rotation in the hole<br />
Color coded<br />
For easy size identification<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # A00025<br />
Found on Page 62<br />
191<br />
FASTENERS
FASTENERS<br />
192<br />
Anchor <strong>Fasteners</strong><br />
Quadlock Anchors<br />
Yellow<br />
102653<br />
Green<br />
102657<br />
Red<br />
102654<br />
Grey<br />
102658<br />
1 800 458-4018 www.uzengprod.com<br />
Brown<br />
102655<br />
Orange<br />
102659<br />
APPLICATIONS:<br />
• Replace all hard plastic, vinyl and other general purpose plugs.<br />
• Use in floors or walls.<br />
• Excellent for hand rails.<br />
• Use with machine bolts, lag bolts, cap screws, wood screws,<br />
sheet metal screws, threaded rod or any threaded fastener.<br />
• Use with stainless steel bolts in corrosive applications.<br />
• Can be used in all indoor and outdoor applications.<br />
Suitable for concrete, stone, low density concrete, expanded<br />
clay, hollow blocks, hollow bricks, solid bricks and plaster<br />
board. For most installation work in which shear loads<br />
dominate. Where pullout loads dominate or where high<br />
temperatures are generated.<br />
Blue<br />
102656<br />
Black<br />
102660<br />
Masonry Drill Bit Assortment<br />
PART #00950KP<br />
PART # COLOR ANCHOR DRILL SCREW QTY. RECOMMENDED LOAD IN LBS.<br />
CODE SIZE SIZE SIZE SHEAR PULL-OUT<br />
102653 Yellow 3/16" x 1" 3/16" #8 thru #10 x 1-1/4" 100 110 55<br />
102654 Red 1/4”x 1-1/4" 1/4" #8 thru #12 x 1-1/2" 100 132 132<br />
102655 Brown 5/16" x 1-1/2" 5/16" #10 thru 1/4" x 2" 50 265 176<br />
102656 Blue 3/8" x 1-3/4" 3/8" #10 thru 5/16" x 2-1/4" 50 309 220<br />
102657 Green 1/2" x 2-1/2" 1/2" #1/4 thur 7/16" x 2-3/4" 50 661 441<br />
102658 Grey 9/16" x 3" 9/16" 7/16" x 3-3/4" 25 882 551<br />
102659 Orange 5/8" x 3-1/2" 5/8" 1/2" x 4" 10 1102 661<br />
102660 Black 3/4" x 4" 3/4" 5/8" x 4-1/4" 10 1323 992<br />
Please check out our standard screw sections for different head selections.<br />
TECHNICAL INFORMATION:<br />
• Rot and corrosion proof<br />
• Resists Formic Acid, Hydrochloric Acid, Ammonium<br />
Hydrate, Uric Acid and most other acids.<br />
• Resists extremes of heat and cold
Bulldog Anchors<br />
Open Type<br />
MAIN USER:<br />
Electrican, joiner, fitter, plumber, window fitter,<br />
plastic, carpenter, HVC fitter, shopfitter and mechanic.<br />
FOR USE IN:<br />
Concrete, natural stone, brick, sandstone and gypsum.<br />
INSTALLATION:<br />
Fastening with plug and wood<br />
screw (pre-assembly fixing)<br />
Application in sandstone<br />
Application in concrete<br />
Masonry Drill Bit Assortment PART #00950KP<br />
Contains: 7 pieces of the most popular size drills<br />
Bulldog Anchors<br />
Closed Type<br />
MAIN USER:<br />
Joiner, electrican, mechanical installations, shopfitters,<br />
plumber and plaster.<br />
FOR USE IN:<br />
Plaster, aerated concrete, hollow brick (without percussion<br />
drilling), sandstone, concrete, chipboard and plasterboard.<br />
INSTALLATION:<br />
Ideal fixing with chipboard<br />
screw into plasterboard<br />
Application in gypsum<br />
Expansion in hollow brick<br />
Application into aerated concrete<br />
Anchor <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
193<br />
FASTENERS
FASTENERS<br />
194<br />
Anchor <strong>Fasteners</strong><br />
Bulldog Anchors<br />
Open Type<br />
The wings<br />
Prevent rotation.<br />
The screw guide<br />
Keeps screw centered during installation.<br />
The stabilization points<br />
Prevents legs from opening while<br />
inserting plug.<br />
The brad point<br />
Facilitates fast and easy entry through<br />
the fixed material on through to the hole.<br />
Please consult our standard screw and drill section for your requirements.<br />
1 800 458-4018 www.uzengprod.com<br />
The knock-in protection<br />
Prevents premature expansion.<br />
The offset block profile<br />
Holds plug firmly to prevent rotation.<br />
The M-teeth<br />
Ensures 100% radial expansion<br />
for maximum pull-out.<br />
ANCHOR DRILL SCREW LOAD CAPACITIES IN LBS.<br />
PART # SIZE QTY. SIZE SIZE CONCRETE HOLLOW SOLID SANDSTONE LIGHTWEIGHT<br />
3500 PSI BRICK BRICK CONCRETE<br />
102733 3/16" x 1" (M5x25) 50 3/16"(M5) #4-#6(M2.6-4) 330 250 310 310 220<br />
102734 1/4" x 1-3/16" (M3.5-5) 50 1/4"(M6) #6-#8(M3.35-5) 550 300 440 440 250<br />
102735 5/16" x 1-1/2"(M8x40) 25 5/16"(M8) #10-#12(M4.5-5) 880 400 770 770 390<br />
102736 3/8" x 2"(M10x50) 25 3/8"(M10) 1/4"-5/16"(M6-8) 1430 500 880 880 460<br />
102737 1/2" x 2-3/8"(M12x60) 25 1/2"(M12) 5/16"-3/16"(M8-10) 2100 700 1280 1450 620<br />
102738 9/16" x 2-3/4"(M14x70) 20 9/16"(M14) 7/16"-1/2"(M10-12) 4000 1820 1980 860<br />
Available in<br />
an Assortment<br />
PART # 103632<br />
Found on Page 62
Bulldog Anchors<br />
Closed Type<br />
The nodal point<br />
Helps to achieve a perfect knot formation<br />
of the plug and gives a positive (keying)<br />
bearing in hollow material.<br />
The fins<br />
Avoid rotation.<br />
The knock-in protection<br />
Prevents premature expansion.<br />
Please consult our standard screw and drill section for your requirements.<br />
Anchor <strong>Fasteners</strong><br />
The brad point<br />
Allows an easy and fast insertion<br />
of plug into drilled hole.<br />
The offset block profile<br />
Ensures rotation resistance and holds<br />
plug firmly against hole.<br />
Initial tension<br />
Prevents plug from rotating in hole.<br />
The break off flange<br />
Allows for through or flush mount fastening.<br />
ANCHOR DRILL SCREW LOAD CAPACITIES IN LBS.<br />
PART # SIZE QTY. SIZE SIZE CONCRETE HOLLOW CONCRETE DRYWALL CHIPBOARD<br />
3500 PSI BRICK BOARD<br />
102739 1/4"x1-3/8"(M6x35) 50 1/4"(M6) #6-#8(M3.5-5) 550 400 280 110 330<br />
102740 1/4"x1-3/4"(M6x45) 50 1/4"(M6) #6-#8(M3.5-5) 650 450 320 140 440<br />
102741 5/16"x2"(M8x50) 25 5/16"(M8) #10-#12(M4.5-5) 1100 880 440 150 470<br />
102742 3/8"x2-3/8"(M10x60) 25 3/8"(M10) 1/4"-5/16"(M6-8) 1760 1200 490 180 550<br />
102743 1/2"x2-3/4"(M12x70) 25 1/2"(M12) 5/16"-7/16"(M8-10) 2600 1400 800<br />
102744 9/16"x3"(M14x75) 20 9/16"(M14) 7/16"-1/2"(M10-12) 4000 1400 940<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 103632<br />
Found on Page 62<br />
195<br />
FASTENERS
FASTENERS<br />
196<br />
Anchor <strong>Fasteners</strong><br />
Wally Speed Toggle<br />
Self-drilling toggle bolt system for heavy-duty drywall anchoring<br />
FEATURES: BENEFITS:<br />
• Fast • Needs no pre-drilling or hole preparation. Installs much faster than standard toggle bolts.<br />
• Easy • Only a #2 Phillips drive is needed to install toggle and screw.<br />
• Secure • High helix thread provides strong engagement in 3/8", 1/2" and 5/8" drywall.<br />
• Positive Clamping • Long clamping arm adds to strength of hold; replaces both 1/8" and 3/16" winged toggles.<br />
• Complete • Each anchor comes with a special #8 x 2-1/8" sheet metal screw.<br />
• Neat • Tri-cut self-drilling point makes a clean, small hole.<br />
Average Performance Values<br />
DRYWALL PULLOUT SHEAR<br />
THICKNESS LBS. LBS.<br />
3/8" 67 230<br />
1/2" 84 235<br />
5/8" 148 303<br />
1. Place #2 phillips screwdriver or<br />
cordless screwdriver (#2 phillips bit)<br />
into the recess of the WALLY SPEED<br />
Toggle, press into gypsum wallboard,<br />
while turning the anchor clockwise.<br />
3. Place fixture in position over installed<br />
WALLY SPEED Toggle. Insert screw.<br />
(#8 diameter x 2-1/8” blunt point)<br />
5. Continue turning screw until tight.<br />
The clamp will move back against<br />
the drywall as the screw is turned.<br />
1 800 458-4018 www.uzengprod.com<br />
SPECIAL<br />
# 8 x 2-1/8”<br />
SHEET METAL<br />
SCREW<br />
2. Continue turning the anchor<br />
until it is seated flush with the<br />
wall. Line up arrows on head<br />
until parallel to stud.<br />
4. Push screw through WALLY<br />
SPEED Toggle to engage clamp.<br />
SPECIAL ROTATING CLAMP<br />
DEEP #2 PHILLIPS RECESS<br />
CLAMP<br />
FLIPS AS<br />
SCREW<br />
ENGAGES<br />
SELF-DRILLING POINT<br />
Wally Speed Toggle<br />
APPLICATIONS:<br />
• Shelving<br />
• Bulletin Boards<br />
• Mirrors<br />
• Fire Extinguishers<br />
• Light Fixtures<br />
• Curtain Rods<br />
• Cabinets<br />
• Closet Organizers<br />
• Electrical Fixtures<br />
• Telecommunication Equipment<br />
• Conduit<br />
• HVAC duct strap<br />
• Appliances<br />
• Signs<br />
• Medical Equipment Boxes<br />
PART # QTY.<br />
91596 10
Wally “Light” Speed Anchors<br />
Light-duty... Self-drilling...<br />
One-piece anchor for mounting to drywall<br />
• No pre-drilling or hole preparation necessary.<br />
• No pre-drilling with #2 Phillips screwdriver or cordless driver.<br />
• Tough, engineered plastic offers 2/3 the performance of standard<br />
Wally Speed Anchors.<br />
• Suitable for use in a 3/8", 1/2" and 5/8" drywall.<br />
• Uses #6 sheet metal screws (not included).<br />
• Easily backed out... leaves small 1/4" hole in drywall.<br />
• Replaces plastic screw anchors and hollow wall anchors.<br />
Average Performance Values<br />
DRYWALL PULLOUT SHEAR<br />
THICKNESS LBS. LBS.<br />
3/8" 29 100<br />
1/2" 36 115<br />
5/8" 46 150<br />
Wally "Light" is fast and easy to install!<br />
1. Place #2 Phillips screwdriver or<br />
cordless screwdriver into recess<br />
of WALLY “LIGHT.”<br />
Wally "Light" Applications:<br />
2. Press into drywall while turning<br />
the anchor clockwise until it<br />
is seated flush with the wall.<br />
• Thermostats • Clocks<br />
• Control Systems • Appliances<br />
• Pictures • Doorbells<br />
• Decorative Wall Hangings • Telecommunications Equipment<br />
• Bathroom Accessories • Signs<br />
• Bulletin Boards • Chalkboards<br />
• Office Material Holders • Remote Control Boxes<br />
• Smoke Detectors • Plaques and Awards<br />
Anchor <strong>Fasteners</strong><br />
Shown Actual Size<br />
PART # QTY.<br />
91632 50<br />
3. Place fixture in position over<br />
installed WALLY “LIGHT.” Insert<br />
with screwdriver (#6 sheet metal<br />
screw is recommended). Tighten<br />
fixture in place. Do not overtighten.<br />
1 800 458-4018 www.uzengprod.com<br />
197<br />
FASTENERS
FASTENERS<br />
198<br />
Anchor <strong>Fasteners</strong><br />
“Wally” Speed Anchors<br />
Self-drilling, one-piece anchor for mounting to gypsum wallboard<br />
FEATURES: BENEFITS:<br />
• Fast • No pre-drilling or hole preparation. Saves time and money.<br />
• Easy • Installs easily with #2 Phillips screwdriver... no electric drill or other tools necessary.<br />
• Removable • Can be easily backed out.<br />
• Secure • Deep threads provide strong engagement in 3/8", 1/2" and 5/8" wallboard.<br />
• Neat • Unique tri-cut point self-drills a clean small hole.<br />
• Breakaway Point • Point can be broken off if cavity behind wall is too shallow.<br />
• Two Styles Available • Standard corrosion resistant zinc material or non-conductive plastic material.<br />
• Versatile • Accepts #8 or #10 diameter sheet metal screws.<br />
Typical Performance Values<br />
DRYWALL PULLOUT SHEAR<br />
THICKNESS LBS. LBS.<br />
3/8" 60 150<br />
1/2" 62 124<br />
5/8" 72 196<br />
“Wally” SPEED ANCHOR WALL APPLICATIONS - Replaces Molly ® ,<br />
plastic screw anchors, or toggle systems.<br />
• Mirrors • Bathroom Accessories<br />
• Shelving and Supports • Signs<br />
• Picture Frames • Curtain Rods<br />
• Brackets • Thermostats<br />
• Bulletin Boards • Closet Organizers<br />
• Plaques and Awards<br />
• Not recommended for ceiling applications<br />
• Coat Racks<br />
“Wally” speed anchors are easy and fast to install!<br />
INSTRUCTIONS:<br />
1. Place #2 Phillips screw<br />
driver into recess of<br />
"WALLY" Speed Anchors.<br />
2. Press into gypsum wall<br />
board while turning<br />
anchor clockwise until<br />
it is seated flush with<br />
the wall.<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
3. Place fixture in position<br />
over installed "WALLY"<br />
Speed Anchor, and insert<br />
screw with a #2 Phillip<br />
screwdriver (#8 type A<br />
or AB screw is<br />
recommended).<br />
PART # MATERIAL QTY.<br />
10397 Zinc 25<br />
91587 Plastic 25<br />
PART # 103632<br />
Found on Page 62<br />
PART # 00760<br />
Found on Page 63<br />
4. Tighten fixture in-place...<br />
threads of screw, selfthread<br />
securely into the<br />
anchor (a minimum of 1"<br />
thread engagement is<br />
recommended). Do not<br />
overtighten.
The GRABB R Anchors<br />
BENEFITS:<br />
• Provides superior holding power.<br />
• Anti-rotational... Stays where you put it!<br />
• GRABB R replaces many other anchors,<br />
so you can reduce your inventory.<br />
• Easy to install and remove without<br />
special tools.<br />
• Versatile... can be used in many materials.<br />
• Made of hardened steel.<br />
• Leaves no gaping holes to be repaired,<br />
so it saves labor.<br />
2 Screw sizes to choose from<br />
Use any style sheet metal screw of the proper diameter.<br />
Sheet metal screws not included with anchors<br />
PART# SIZE QTY.<br />
160540 #8 100<br />
160541 #10 100<br />
Reinforced legs.<br />
Anti-rotational.<br />
Requires minimum<br />
screw length.<br />
Constant prevailing torque.<br />
GRABB R is highly versatile, it can be used in...<br />
One anchor for every use!<br />
Hardened spring steel.<br />
• Drywall • Plywood • Paneling • Pegboard<br />
• Masonite • Hollow Core Doors • Plaster • Particle Board<br />
The anchor with a memory!<br />
As the screw is tightened into the GRABBR ANCHOR, it expands in the hole. When the screw is loosened, the<br />
GRABB R’s exclusive memory feature automatically returns it to its original configuration. It can then be easily<br />
removed without leaving a gaping hole to be repaired!<br />
Without starter hole in: 3/8", 1/2", 5/8" DRYWALL HOLLOW CORE DOORS PEGBOARD<br />
With 1/8" starter hole in: 1/8", 1/4", 3/16" PANELING, 1/4" TO 3/4" PLYWOOD 1/4", 3/16" MASONITE PLASTER<br />
Anchor <strong>Fasteners</strong><br />
Usable with a wide variety<br />
of material thickness and<br />
compositions.<br />
Self-aligning.<br />
1 800 458-4018 www.uzengprod.com<br />
Surface<br />
thread<br />
engagement.<br />
Variable thread sizes.<br />
Positive locking.<br />
Available in<br />
an Assortment<br />
PART # 103632<br />
Found on Page 62<br />
199<br />
FASTENERS
FASTENERS<br />
200<br />
Anchor <strong>Fasteners</strong><br />
Toggler ® System<br />
FEATURES: BENEFITS:<br />
• Quickly Installed • Saves time, labor and replacement cost resulting in lowest overall costs.<br />
• Versatile • Works in any wall thickness (hollow wall, solid sheetrock, or concrete).<br />
• Simple • Needs only one drill bit - 5/16 <strong>UZ</strong> #90155 or use Handy Installation<br />
• Easy to Install Tool #91551.<br />
• Accessible • Will not rotate in hole during installation. Can use electric screwdriver.<br />
• Secure • Accepts large range of screws sizes: #6 to #14.<br />
• Wide Range of Applications • Only Anchor that locks in place before screw is installed.<br />
• Usable at temperature extremes: -20°F to +220°F. Non-conductive.<br />
One fits all, regardless of wall.<br />
INSTRUCTIONS:<br />
THIN THICK SOLID<br />
Approved by GSA for use by all U.S. Government Agencies.<br />
1 800 458-4018 www.uzengprod.com
Toggler ® System<br />
Hollow Door Anchors<br />
DOOR OR PANEL THICKNESS PART # QTY.<br />
1/8" to 1/4" 10431 50<br />
Wire Shelf Anchors<br />
WALL THICKNESS PART # QTY.<br />
3/8" to 1/2" 06507 25<br />
Pegboard Anchors<br />
WALL THICKNESS PART # QTY.<br />
3/8" to 1/2" 06508 25<br />
Wire Anchors<br />
WALL THICKNESS PART # QTY.<br />
3/8" to 1/2" 10432 50<br />
5/8" to 3/4" 10433 50<br />
3/4" to 1" 06527 25<br />
1" to 1-1/4" 06504 25<br />
1-1/4" to 1-1/2" 06505 25<br />
Shelving Anchors<br />
WALL THICKNESS PART # QTY.<br />
3/8" to 1/2" 06506 25<br />
Picture Hook Anchors<br />
WALL THICKNESS PART # QTY.<br />
3/8" to 1/2" 10434 25<br />
Wire Harness Anchors<br />
• Secures wires, cables, PVC piping quickly and neatly.<br />
• One-piece design replaces separate cable harness,<br />
anchor and attaching brackets.<br />
• Works in hollow or solid walls.<br />
Toggler ® Installation Tool<br />
• Easy and fast installation of all plastic Toggler ®<br />
anchors in drywall or plasterboard.<br />
• Includes a 5/16" drill blade and installation key.<br />
Anchor <strong>Fasteners</strong><br />
Available in<br />
an Assortment<br />
PART # 00750<br />
Found on Page 63<br />
WALL THICKNESS PART # QTY.<br />
1/2" to 1/4" 91548 25<br />
3/8" to 1/2" 91549 25<br />
5/8" to 3/4" 91550 25<br />
PART # QTY<br />
91551 1<br />
1 800 458-4018 www.uzengprod.com<br />
201<br />
FASTENERS
FASTENERS<br />
202<br />
Anchor <strong>Fasteners</strong><br />
Hefty Toggle Heavy Duty Anchors<br />
A Heavy Duty Anchor for use in all hollow building materials such as concrete block and drywall.<br />
Here’s how you will benefit by using Hefty Toggle Anchors...<br />
• Super high strength.<br />
• Installs at least three times faster than old fashioned Toggle Bolts.<br />
• Adjust automatically for different wall and ceiling thicknesses.<br />
• Stays in place even when the bolt is removed.<br />
• Lets you use a shorter bolt than Toggle Bolts.<br />
HOLE IN MEDIUM DENSITY CONCRETE BLOCK<br />
PART # SIZE SIZE TENSILE (LBS.) SHEAR (LBS.) QTY.<br />
06501 3/16(10-24) 1/2 645 670 25<br />
06502 1/4-20 1/2 877 1477 25<br />
06503 3/8-16 3/4 1120 2044 10<br />
160528 1/2-13 3/4 2038 2728 10<br />
EASY INSTALLATION:<br />
Step-By-Step<br />
1. Drill a 1/2" (Ø13mm) hole. Hold metal channel flat alongside plastic<br />
straps and slide channel through hole. Minimum clearance behind<br />
wall: 1-7/8" (48mm).<br />
2. Hold ends of straps between thumb and forefinger and pull toward<br />
you until channel rests flush behind wall. Slide plastic cap along<br />
straps with other hand until flange of cap is flush with wall.<br />
3. Snap straps at wall by pushing side to side, snapping off straps<br />
level with flange of cap.<br />
4. Place item over flange. Insert bolt through item and tighten until<br />
flush against item, then stop. Use machine screw or bolt to match<br />
thread in channel: BA (3/16"-24), BB (1/4"-20), BM5 (M5),<br />
and BM6 (M6). Bolt length = item thickness +<br />
wall or ceiling thickness + 1/2" (13mm).<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00589<br />
Found on Page 63
Hollow Wall Anchors<br />
• Permits pre-installation of fastener into hole.<br />
• Ideal for all Hollow Wall applications.<br />
• Screw and fixture removable without disturbing the anchor.<br />
OVERALL WALL DRILL<br />
PART # SIZE LENGTH THICKNESS SIZE QTY.<br />
10170 1/8 Short 1-1/4 1/8-1/2" 5/16 25<br />
10171 1/8 Long 1-11/16 5/8-7/8" 5/16 25<br />
10172 3/16 Short 2-1/16 1/8-5/8" 3/8 10<br />
10173 3/16 Long 2-9/16 5/8-1-3/16" 3/8 10<br />
10174 1/4 Short 2-1/16 1/8-5/8" 7/16 10<br />
10175 1/4 Long 2-9/16 5/8-1-3/8" 7/16 10<br />
Drive Type Anchors<br />
OVERALL WALL<br />
PART # SIZE LENGTH THICKNESS QTY.<br />
10176 1/8 Short 1-1/4 1/8-1/2" 20<br />
10177 1/8 Long 1-11/16 5/8-7/8" 20<br />
Hollow Wall Anchor Setter<br />
Install hollow wall fasteners in seconds, with little effort...<br />
• No adjustments necessary.<br />
• Quick-positive set will all brands and sizes.<br />
• Simple slip in fit.<br />
• Offset head for use in corners.<br />
• One hand installation.<br />
• Cushion grip handles.<br />
PART # 91552<br />
USE ON ALL SURFACE TYPES:<br />
Wallboard, plywood, hardboard, sheetrock, asbestos,<br />
cement plasterboard, thin veneer and brick.<br />
Anchor <strong>Fasteners</strong><br />
Available in<br />
an Assortment<br />
PART #00588<br />
Found on Page 63<br />
1 800 458-4018 www.uzengprod.com<br />
203<br />
FASTENERS
FASTENERS<br />
204<br />
Anchor <strong>Fasteners</strong><br />
Toggle Bolts -Spring Wing Type - Round and Flat Head<br />
• Automatic spring action toggles.<br />
• Uni-zinc plated.<br />
• Bolts threaded to head.<br />
• Combination Drive. (Rd Hd only)<br />
DRILL HOLDING<br />
PART # STYLE SIZE SIZE POWER LBS. QTY.<br />
10398 R.H. 6-32 (1/8) x 2 50<br />
10399 R.H. 6-32 (1/8) x 3 10<br />
10904 R.H. 6-32 (1/8) x 4 3/8" 64 10<br />
160450 F.H. 6-32 (1/8) x 2 50<br />
160452 F.H. 6-32 (1/8) x 4 50<br />
10185 R.H. 10-24 (3/16) x 2 10<br />
10186 R.H. 10-24 (3/16) x 3 10<br />
10187 R.H. 10-24 (3/16) x 4 10<br />
10188 R.H. 10-24 (3/16) x 5 1/2" 180 10<br />
10189 R.H. 10-24 (3/16) x 6 10<br />
160454 F.H. 10-24 (3/16) x 3 50<br />
160455 F.H. 10-24 (3/16) x 4 50<br />
10191 R.H. 1/4-20 x 3 10<br />
10192 R.H. 1/4-20 x 4 10<br />
10193 R.H. 1/4-20 x 5 5/8" 400 10<br />
10194 R.H. 1/4-20 x 6 10<br />
160458 F.H. 1/4-20 x 3 50<br />
160459 F.H. 1/4-20 x 4 50<br />
160437 R.H. 5/16-18 x 4 25<br />
160438 R.H. 5/16-18 x 5 7/8" 580 25<br />
160439 R.H. 5/16-18 x 6 25<br />
10195 R.H. 3/8-16<br />
.<br />
x 4 5<br />
10196 R.H. 3/8-16 x 5 1" 600 5<br />
10197 R.H. 3/8-16 x 6 5<br />
For Hard Material: Concrete, Concrete Block, Tile & Similar Material, Use Drill 1/16” Larger Than Size Shown.<br />
Spring Wing - Heads Only<br />
• Uni-zinc plated.<br />
PART # DIA.<br />
DRILL<br />
SIZE QTY.<br />
10920 #6 (1/8) 3/8 20<br />
10198 #10 (3/16) 1/2 20<br />
10199 1/4 5/8 20<br />
10200 5/16 7/8 10<br />
10201 3/8 1 10<br />
1 800 458-4018 www.uzengprod.com<br />
Round Head Style shown
Vinyl Screw Anchors<br />
• Made from vinyl, designed for maximum efficiency in any material.<br />
• Square design eliminates anchor turning in the hole.<br />
• For use in virtually any material you can drill a hole into.<br />
• Color coded for easy selection of proper size.<br />
• Not affected by heat, cold or most chemicals.<br />
• For use with wood screws or sheet metal screws.<br />
1. Drill proper size<br />
hole 1/16" deeper<br />
than anchor length.<br />
MATERIALS:<br />
2. Insert anchor and<br />
tap into hole with<br />
hammer. Screw<br />
length = length of<br />
anchor + thickness<br />
of fixture.<br />
R= recommended<br />
S= suitable<br />
Brick R<br />
Concrete R<br />
Cinder Block R<br />
Plaster S<br />
Marble R<br />
Masonry R<br />
Dry Wall S<br />
Stone R<br />
Tile R<br />
3. Anchor expands as<br />
wood screw or sheet<br />
metal screw is driven in.<br />
USE SCREW LENGTH OF COLOR HOLE<br />
PART # DIA. ANCHOR CODE SIZE QTY.<br />
160510 1-3 1 Yellow 1/8" 100<br />
160511 4-6 1 White 3/16" 100<br />
160512 7-9 1 Red 15/64" 100<br />
160513 7-9 1-1/2 Red 15/64" 100<br />
160514 10-12 1 Green 1/4" 100<br />
160515 10-12 1-1/4 Green 1/4" 100<br />
160516 10-12 1-1/2 Green 1/4" 100<br />
160517 10-12 2 Green 1/4" 100<br />
160518 #14 or 1/4" 1 Blue 5/16" 50<br />
160519 #14 or 1/4" 1-1/2 Blue 5/16" 50<br />
160520 #14 or 1/4" 2 Blue 5/16" 50<br />
160521 5/16" 1-1/2 Orange 3/8" 25<br />
160522 5/16" 2 Orange 3/8" 25<br />
160523 5/16" 2-1/2 Orange 3/8" 25<br />
Anchor <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
205<br />
FASTENERS
FASTENERS<br />
206<br />
Anchor <strong>Fasteners</strong><br />
Plastic Screw Anchors<br />
• For use in plaster, wood, wallboard, sheetrock, drywall, brick block, concrete, etc.<br />
• Won’t rust or corrode.<br />
• Lip prevents anchors from sinking in soft materials.<br />
• Tapered tips on all styles for easy insertion.<br />
• For use with sheet metal screws.<br />
• Anchor length same as screw length.<br />
Typical applications for these anchors...<br />
• Mirrors •Pictures • Conduit Straps • Racks<br />
• Signs •Fixtures • Shelves • Cabinets<br />
• Mail Boxes •And Many Others!<br />
Standard<br />
• Hard (rigid) plastic.<br />
• 3 Tapered ribs.<br />
• Expands in 3 directions.<br />
• The easiest to remove.<br />
Ribs-and-hooks<br />
• “Rib-and-Hook” design provides good<br />
holding strength in soft materials.<br />
• Our most economical plastic anchor.<br />
• Made from resilient plastic.<br />
Heavy Duty Anchors<br />
• When a screw is inserted, the serrated tabs<br />
on each side of the neck expand to provide<br />
stability against rotation as well as improved<br />
holding strength.<br />
• The expanded ribbed body prevents pull-out.<br />
1 800 458-4018 www.uzengprod.com<br />
DRILL SCREW SIZE<br />
PART # SIZE ANCHOR LENGTH QTY.<br />
10202 3/16 #4-8 x 3/4" 100<br />
10203 3/16 #6-10 x 7/8" 100<br />
10204 1/4 #10-12 x 1" 100<br />
10205 5/16 #14-16 x 1-3/8" 100<br />
DRILL SCREW SIZE<br />
PART # SIZE ANCHOR LENGTH QTY.<br />
160529 3/16 #6-8 x 7/8" 100<br />
160530 1/4 #10-12 x 1" 100<br />
160531 5/16 #14-16 x 1-1/2" 100<br />
DRILL SCREW SIZE<br />
PART # SIZE ANCHOR LENGTH QTY.<br />
06524 3/16 #4-6-8 X 1" 100<br />
06525 1/4 #8-10-12 x 1-1/4" 100<br />
06526 5/16 #12-14-16 x 1-1/2" 100<br />
Available in<br />
an Assortment<br />
PART #00471KP<br />
Found on Page 64<br />
PART #00472KP<br />
Found on Page 64<br />
PART #00473KP<br />
Found on Page 64
Wedge Anchors<br />
• Uni-Zinc Plated For Added Protection.<br />
• Holes Can Be Drilled Through Fixtures Mounting Holes.<br />
• Drilled Hole Diameter Is Same As Anchor Diameter.<br />
FAST, SIMPLE INSTALLATION:<br />
Select anchor long enough to accommodate thickness of<br />
fixture and nut, plus minimum imbedment indicated.<br />
1. Drill the same diameter<br />
as Anchor. Hole can be<br />
drilled directly through<br />
the fixture mounting<br />
holes. The depth of the<br />
hole should accommodate<br />
the minimum recommended<br />
imbedment.<br />
2. Insert the Anchor<br />
and tap into the<br />
hole so that at<br />
least some threads<br />
are below the top<br />
surface of fixture.<br />
As the nut is tightened,<br />
the stud is pulled up,<br />
expanding the steel collar<br />
and forcing it tightly into<br />
the concrete, generating<br />
greater holding power.<br />
3. Tighten the nut.<br />
Resistance will<br />
increase quickly<br />
after three or four<br />
complete turns.<br />
Anchor <strong>Fasteners</strong><br />
APPROX. HOLE MINIMUM THREAD STRENGTH<br />
PART # QTY. DIA. LENGTH SIZE IMBEDMENT LENGTH PULLOUT(Lbs.) SHEAR(Lbs.)<br />
10055 10 1-3/4<br />
10056 10 1/4" 2-1/4 1/4" 1-1/8 3-1/4 2150 2120<br />
10057 10 3-1/4<br />
160173 5<br />
2-1/4<br />
10058<br />
10059<br />
5<br />
5<br />
3/8"<br />
2-3/4<br />
3-3/4<br />
3/8" 1-5/8 1-1/8 5130 3810<br />
160176 5 5<br />
10060 5<br />
2-3/4<br />
10061<br />
10062<br />
5<br />
2<br />
1/2"<br />
3-3/4<br />
5-1/2<br />
1/2" 2-1/4 1-1/4 7040 10530<br />
160180 5 7<br />
10063 5 3-1/2<br />
10064 2 5/8" 4-1/2 5/8" 2-3/4 1-1/2 13250 14110<br />
10065 2 6<br />
10066<br />
10067<br />
2<br />
2<br />
3/4"<br />
5-1/2<br />
7<br />
3/4" 3-1/4 1-1/2 13350 18180<br />
10068<br />
10069<br />
2<br />
2<br />
1"<br />
6<br />
9<br />
1" 4-1/2 2-1/4 31830 25530<br />
1 800 458-4018 www.uzengprod.com<br />
207<br />
FASTENERS
FASTENERS<br />
208<br />
Anchor <strong>Fasteners</strong><br />
Steel Sleeve Anchor Bolts<br />
• Ideal For Medium To Heavy Duty Anchoring.<br />
• Supplied Pre-assembled For Ready Installation.<br />
• No Special Tools Required.<br />
• Drilled Hole and Anchor Are Same Diameter.<br />
• Rust Resistant Uni-Zinc Plating.<br />
• Steel Sleeve Expands Over Full Length of Bolt.<br />
1. Pre-drill same diameter<br />
as anchor.<br />
2. Install anchor<br />
through fixture.<br />
APPROX. MINIMUM<br />
DESCRIPTION PART# DIA. LENGTH HOLE DEPTH QTY.<br />
Slotted 10070 1-1/4 20<br />
Round 10071 1/4 2 1" 20<br />
Head 10072 2-3/4 20<br />
10076<br />
10077<br />
3/8<br />
2-1/2<br />
3-3/4<br />
1-1/4"<br />
20<br />
10<br />
Slotted 10078 1-3/8 20<br />
Flat 10079 2 20<br />
Head 10080 1/4 3 1" 10<br />
10081 4 5<br />
10082 5-1/4 5<br />
10084 3-1/2 1" 5<br />
10085<br />
10086<br />
3/8<br />
2-3/4<br />
4<br />
1-1/4"<br />
5<br />
5<br />
Acorn Nut 10088<br />
10089<br />
1/4 1-3/8<br />
2-1/4<br />
1"<br />
25<br />
20<br />
10090<br />
10091<br />
1-1/2<br />
1"<br />
10<br />
5/16<br />
2-1/2 10<br />
Hex Nut<br />
10092<br />
10093<br />
1-7/8<br />
1-1/4"<br />
10<br />
3/8<br />
3 10<br />
10094<strong>UZ</strong><br />
10095<strong>UZ</strong><br />
2-1/4<br />
1-1/2"<br />
5<br />
1/2<br />
2-3/4 5<br />
10096 2-1/4 5<br />
10097 5/8 4-1/4 2" 5<br />
10098 6 5<br />
10099 2-1/2 2" 5<br />
10100<br />
10101<br />
3/4 4-1/4<br />
6-1/4<br />
2-1/2"<br />
5<br />
25<br />
Stud Bolt 10102 1/4 1-3/8 1-3/8" 25<br />
10104<strong>UZ</strong> 3/8 1-7/8 1-7/8" 5<br />
10105 1/2 2-1/4 2-1/4" 5<br />
1 800 458-4018 www.uzengprod.com<br />
3. Tighten with wrench<br />
or screwdriver.
<strong>UZ</strong> Taper Anchor<br />
The <strong>UZ</strong> Taper Anchor is the strongest, most versatile anchoring system available.<br />
The two component, expansion type unit is designed for applications where a<br />
high strength anchor is needed and a finished head style is desired.<br />
For use in concrete or masonry.<br />
More about the <strong>UZ</strong> Taper Anchor…<br />
MADE IN<br />
U.S.A.<br />
150,000 tensile strength / Grade 5<br />
This provides superior strength and ductility.<br />
The hole diameter and anchor are the same<br />
This means no repositioning of equipment is needed; installation can be performed with the fixture in place.<br />
Fewer tools are required.<br />
<strong>UZ</strong> Taper Anchor is reusable and removable<br />
This is an inventory and cost reduction. The anchor can be removed and placed in a new location (just replace<br />
the expansion nut) or placed back in the original hole. Just follow the same installation procedure as the original<br />
set up.<br />
Two-part expansion nut<br />
This allows the nut to expand parallel to the hole. The horizontal loading enhances concrete strength. This<br />
eliminates the "cone out" damage standard anchors can cause.<br />
Hex head design<br />
No studs are exposed in the floor after installation, preventing safety issues.<br />
Compared to a wedge type anchor the shear strength is considerably higher<br />
At 3000 PSI<br />
3/8" dia. <strong>UZ</strong> Taper Anchor -7,177 Wedge anchor - 3,810<br />
1" dia. <strong>UZ</strong> Taper Anchor - 36,257 Wedge anchor - 25,530<br />
Areas of use:<br />
Metal fencing, Railings, Power lifts, Conveyors, Vibration Equipment, Industrial Mixers, Sign posts, Electrical Boxes,<br />
Automation Equipment, Robotics, Storage Bins, Guard Rails…..and many more.<br />
Anchor <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
209<br />
FASTENERS
FASTENERS<br />
210<br />
Anchor <strong>Fasteners</strong><br />
Quantity<br />
5<br />
5<br />
5<br />
5<br />
5<br />
5<br />
5<br />
5<br />
10<br />
5<br />
5<br />
5<br />
10<br />
2<br />
2<br />
2<br />
2<br />
5<br />
2<br />
2<br />
2<br />
2<br />
5<br />
1<br />
1<br />
2<br />
Part Number<br />
113122<br />
113123<br />
113124<br />
113125<br />
113126<br />
113127<br />
113128<br />
113129<br />
113130<br />
113131<br />
113132<br />
113133<br />
113134<br />
113135<br />
113136<br />
113137<br />
113138<br />
113139<br />
113140<br />
113141<br />
113142<br />
113143<br />
113144<br />
113145<br />
113146<br />
113147<br />
*Ultimate Tensile and Shear Loads in lbs.<br />
Description<br />
1/4 x 1-3/4<br />
1/4 x 2-1/2<br />
1/4 x 3-1/2<br />
1/4” nut only<br />
3/8 x 2-1/4<br />
3/8 x 2-5/8<br />
3/8 x 3<br />
3/8 x 4<br />
3/8” nut only<br />
1/2 x 2-7/8<br />
1/2 x 4<br />
1/2 x 5<br />
1/2” nut only<br />
5/8 x 3-1/2<br />
5/8 x 4-1/2<br />
5/8 x 6<br />
5/8 x 7<br />
5/8” nut only<br />
3/4 x 4-1/8<br />
3/4 x 5-1/2<br />
3/4 x 7<br />
3/4 x 8<br />
3/4” nut only<br />
1 x 5-5/8<br />
1 x 7-1/4<br />
1” nut only<br />
Installation Procedure:<br />
Required<br />
Torque to Set<br />
30<br />
1 800 458-4018 www.uzengprod.com<br />
40<br />
90<br />
125<br />
250<br />
550<br />
1) Drill the hole the same diameter as the <strong>UZ</strong> Taper Anchor, using<br />
fixture as a template.<br />
2) Drive <strong>UZ</strong> Taper Anchor into place leaving recommended head<br />
clearance. (Refer to the chart or calculate half of the diameter<br />
of the anchor). If the hole is oversized, simply remove and<br />
pre-expand the expander nut to fit the hole.<br />
3) Tighten the <strong>UZ</strong> Taper Anchor to recommended torque.<br />
4) For larger projects, set Taper Anchor with an impact wrench.<br />
Minimum<br />
Embedment<br />
1-1/4<br />
1-7/8<br />
2-3/8<br />
2-7/8<br />
3-3/8<br />
4-5/8<br />
Required<br />
Head<br />
Clearance<br />
1/8<br />
3/16<br />
1/4<br />
5/16<br />
7/16<br />
5/8<br />
Tension<br />
(Cured Concrete)<br />
3,000 psi*<br />
1,600<br />
4,030<br />
8,165<br />
9,990<br />
11,906<br />
28,263<br />
Shear<br />
3,000 psi*<br />
2,425<br />
7,177<br />
12,177<br />
17,030<br />
27,916<br />
36,257<br />
Available in<br />
Assortments<br />
Found on Page 65<br />
Maintenance<br />
Tray<br />
Part # 00958<br />
Master<br />
Bin<br />
Part # 00959
Anchor <strong>Fasteners</strong><br />
Center Pin Drive Anchors<br />
Center Pin Drive Anchors are designed for anchoring all types of products into concrete.<br />
• Easy to use.<br />
• Anchor size is hole size.<br />
• Insert anchor into hole with nut and washer attached.<br />
• Hammer pin until flush.<br />
• The nut and washer can be preset for the desired embedment.<br />
• The Center Pin Drive Anchor is visually inspectable after it is set. When the head of the pin meets the threads, the anchor is set.<br />
• Excellent holding values.<br />
Center Pin Drive Anchor Applications:<br />
• Medium to heavy applications into concrete • Anchoring outlet boxes • Stadium seats<br />
• Wood or steel plates • Conveyor systems • Hand rails<br />
• Steel buildings • Light fixtures • Anchoring machinery<br />
Installation Instructions<br />
1. Drill the hole perpendicular to the work surface. To assure full holding<br />
power, do not ream the hole or allow drill to wobble.* Clean hole using<br />
compressed air and a nylon brush. A clean hole is necessary for proper<br />
performance.<br />
2. Present the nut and washer for desired embedment.<br />
3. Hammer center pin until it is aligned with the top of the bolt.<br />
4. Tighten nut.<br />
Maximum Pull-Out & Shear Capacity for Static Loads<br />
Anchor Embedment<br />
2000 PSI (FT-LBS)<br />
Diameter Depth Pull-Out Shear<br />
1/4 1-1/8 900 1600<br />
5/16 1-1/2 1400 3000<br />
3/8 1-7/8 2200 3400<br />
1/2 2-1/2 3600 7200<br />
5/8 2-3/4 5400 9200<br />
3/4 3 7500 13500<br />
Values shown are average ultimate values and offered only as a guide and are not guaranteed.<br />
A safety factor of 4:1 or 25% is generally accepted as a safe working load.<br />
PART #<br />
115935<br />
115936<br />
115937<br />
115938<br />
115939<br />
115940<br />
115941<br />
115942<br />
115943<br />
115944<br />
115945<br />
115946<br />
115947<br />
115948<br />
115949<br />
115950<br />
ANCHOR SIZE<br />
DIA. X LENGTH<br />
1/4 X 1-3/4<br />
1/4 X 2-3/8<br />
5/16 X 2<br />
5/16 X 2-3/4<br />
3/8 X 2-3/8<br />
3/8 X 3-1/2<br />
3/8 X 4-3/4<br />
1/2 X 2-3/4<br />
1/2 X 3-1/2<br />
1/2 X 4-3/4<br />
1/2 X 6<br />
5/8 X 4<br />
5/8 X 6<br />
3/4 X 5<br />
3/4 X 6<br />
3/4 X 7-1/2<br />
THREAD LENGTH<br />
(INCHES)<br />
5/8<br />
3/4<br />
5/8<br />
1<br />
1<br />
1-1/8<br />
1-1/2<br />
1<br />
1-1/8<br />
2<br />
2<br />
1-5/8<br />
2<br />
2<br />
2<br />
2<br />
*Always wear safety glasses. Follow drill manufacturer's instructions.<br />
Use only solid carbide-tipped drill bits meeting ANSI 8212.15<br />
diameter standards.<br />
Available in<br />
an Assortment<br />
MINIMUM<br />
EMBEDMENT<br />
1-1/8<br />
1-1/8<br />
1-3/8<br />
1-3/4<br />
1-3/8<br />
1-3/4<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/4<br />
2-1/4<br />
2-3/4<br />
2-3/4<br />
3<br />
3<br />
3<br />
DRILL SIZE QTY.<br />
1/4<br />
1/4<br />
5/16<br />
5/16<br />
3/8<br />
3/8<br />
3/8<br />
1/2<br />
1/2<br />
1/2<br />
1/2<br />
5/8<br />
5/8<br />
3/4<br />
3/4<br />
3/4<br />
1 800 458-4018 www.uzengprod.com<br />
PART #00468<br />
Found on Page 65<br />
50<br />
50<br />
50<br />
50<br />
25<br />
25<br />
25<br />
10<br />
10<br />
10<br />
10<br />
5<br />
5<br />
5<br />
5<br />
5<br />
211<br />
FASTENERS
FASTENERS<br />
212<br />
Anchor <strong>Fasteners</strong><br />
Machine Screw Anchors<br />
• Ideal for anchoring to concrete, brick, stone, • Fixtures Removable.<br />
or other masonry. • Masonry can be resurfaced.<br />
• Lead sleeve and alloy cone resist oxidation.<br />
• Attractive and finished appearance; no studs<br />
show when installed; the nut is in the hole.<br />
1. Pre-drill the<br />
recommended<br />
size hole and<br />
insert the anchor with the<br />
tapered end first.<br />
Drop-In Anchors<br />
• Ideal for any masonry application. • Eliminates dropped or lost plugs.<br />
• Smooth wall mates with concrete as • Zinc plated for corrosion resistance.<br />
anchor expands-provides friction fit.<br />
1. Drill hole 1/8” deeper than<br />
anchor length for flush<br />
mounting. Where surface<br />
deterioration is present, drill<br />
hole somewhat deeper to<br />
permit anchor to be<br />
recessed below surface.<br />
2. Position the setting tool and set the<br />
anchor with a few sharp hammer<br />
blows. The lead sleeve will firmly<br />
compact over the cone and into<br />
every crevice of the masonry.<br />
PART # SIZE QTY. DIA. DEPTH<br />
SETTING TOOL<br />
PART # QTY.<br />
10140 6-32 20 1/4 3/8 10150 1<br />
10141 8-32 20 5/16 1/2 10151 1<br />
10142 10-24 20 3/8 5/8 10152 1<br />
10144 1/4-20 20 1/2 7/8 10154 1<br />
10145 5/16-18 10 5/8 1 10155 1<br />
10146 3/8-16 10 3/4 1-1/4 10156 1<br />
10147 1/2-13 5 7/8 1-1/2 10157 1<br />
10148 5/8-11 2 1-1/8 2 10158 1<br />
10149 3/4-10 2 1-1/4 2-1/4 10159 1<br />
2. Drop anchor into hole. If<br />
hole is slightly undersized,<br />
tap anchor in with hammer<br />
until it bottoms in hole.<br />
1 800 458-4018 www.uzengprod.com<br />
3. To set expander plug,<br />
installation tool can be<br />
struck a few sharp<br />
blows with a hammer<br />
or an automatic air or<br />
electric tool can be used.<br />
3. The anchor is then secured<br />
and ready to accept the<br />
fixture using a standard<br />
machine a screw or bolt.<br />
4. Place fixture in position,<br />
insert bolt and tighten.<br />
USE BOLT ANCHOR THREAD SETTING TOOL<br />
PART # DRILL BIT SIZE LENGTH DEPTH QTY. PART # QTY.<br />
10160 5/16 1/4 1-1/8 7/16 10 10165 1<br />
10161 1/2 3/8 1-5/8 5/8 10 10166 1<br />
10162 5/8 1/2 2 11/16 5 10167 1<br />
10163 7/8 5/8 2-1/2 7/8 2 10168 1<br />
10164 1 3/4 3-1/8 1-3/8 2 10169 1
Single Machine Bolt Shields<br />
• Made of rust proof zinc alloy.<br />
• Use with machine screws, machine bolts, cap screws.<br />
• Universal application.<br />
1. Drill hole and place shield<br />
into hole with wedge<br />
shaped nut first.<br />
1. After drilling hole, insert<br />
the shield into hole.<br />
2. Shield is now positioned to receive<br />
standard machine bolt or machine screw.<br />
BOLT SHIELD & DRILL HOLE DIMENSIONS<br />
PART # SIZE LENGTH DRILL SIZE QTY.<br />
10128 1/4 1-1/4 1/2 10<br />
10129 5/16 1-1/2 5/8 10<br />
10130 3/8 1-1/2 5/8 5<br />
10131 1/2 2 7/8 5<br />
10132 5/8 2-5/8 1 2<br />
10133 3/4 3-1/2 1-1/4 2<br />
Double Machine Bolt Shields<br />
• For secure heavy loads subject to vibration, axial and shear pull.<br />
• Made of high grade rust proof Zinc Alloy.<br />
• Parts held together firmly by high grade center spring.<br />
• Uniform expansion gives efficient anchoring.<br />
• Quickly installed in all types of solid masonry.<br />
• Universal application.<br />
2. Shield in position. Note: Threaded nut<br />
must be at bottom of hole.<br />
BOLT SHIELD & DRILL HOLE DIMENSIONS<br />
PART # SIZE LENGTH DRILL SIZE QTY.<br />
10134 1/4 1-1/4 1/2 10<br />
10135 5/16 1-5/8 5/8 10<br />
10136 3/8 2 3/4 5<br />
10137 1/2 2-1/4 7/8 5<br />
10138 5/8 3 1 2<br />
10139 3/4 3-1/2 1-1/4 2<br />
Anchor <strong>Fasteners</strong><br />
3. Place work over hole. As machine<br />
bolt is tightened, wedge-shaped<br />
nut is drawn up into shield to expand<br />
and grip sides of hole.<br />
3. With work in position and bolt tightened<br />
the threaded wedge-shaped nut is<br />
drawn up, and the plain wedge-shape<br />
nut is also forced into shield, thus<br />
causing the shield to expand at both top<br />
and bottom.<br />
1 800 458-4018 www.uzengprod.com<br />
213<br />
FASTENERS
FASTENERS<br />
214<br />
Anchor <strong>Fasteners</strong><br />
Lag Shields<br />
• Will not flatten out. • Short shields for hard masonry.<br />
• High tensile and compressive strength. • Long shields for soft masonry.<br />
• Reinforced rings give maximum bite. • Die cast from special alloy.<br />
• Ideal for anchoring in concrete, brick or other masonry. • Resists rust.<br />
INSTRUCTIONS:<br />
1. After drilling hole, lag<br />
shield is inserted in<br />
position.<br />
Lead Shields<br />
1 800 458-4018 www.uzengprod.com<br />
2. Place fixture over bolt and<br />
turn screw into shield which<br />
expands, thus holding the<br />
work securely.<br />
SHIELD & DRILLED HOLE DIMENSIONS<br />
PART # SIZE LENGTH DRILL SIZE QTY.<br />
10107 1/4 1 1/2 50<br />
10108 1/4 1-1/2 1/2 50<br />
10109 5/16 1-1/4 1/2 50<br />
10110 5/16 1-13/16 1/2 50<br />
10111 3/8 1-3/4 5/8 25<br />
10112 3/8 2-1/2 5/8 25<br />
10113 1/2 2 3/4 25<br />
10114 1/2 3 3/4 25<br />
10115 5/8 2 7/8 10<br />
10116 5/8 3-1/4 7/8 10<br />
10118 3/4 3-1/2 1 10<br />
• Ideal for anchoring in any masonry, brick, or concrete with wood or sheet metal screws.<br />
• Made of high grade lead.<br />
• Screw cuts own threads as shield expands.<br />
• Exterior ribs grip the sides of the hole for positive anchoring.<br />
INSTRUCTIONS:<br />
1. Drill hole in masonry. Insert<br />
shield in position.<br />
2. Tap shield gently with<br />
hammer until end of shield<br />
is flush with surface.<br />
PART # SIZE LENGTH USE WITH SCREW DRILL SIZE QTY.<br />
10119 1/8 3/4 6-8 1/4 50<br />
10120 1/8 1 6-8 1/4 50<br />
10121<strong>UZ</strong> 1/8 1-1/2 6-8 1/4 50<br />
10122 3/16 3/4 10-14 5/16 50<br />
10123<strong>UZ</strong> 3/16 1 10-14 5/16 50<br />
10124<strong>UZ</strong> 3/16 1-1/2 10-14 5/16 50<br />
10126<strong>UZ</strong> 1/4 1 5/16-3/8 3/8 25<br />
10127 1/4 1-1/2 5/16-3/8 3/8 25<br />
3. Place fixture in position and<br />
insert screw. Screw will cut<br />
its own thread and cause<br />
outward expansion of shield<br />
gripping sides firmly.
Nail-In Hammer Drive Anchor<br />
• Easy to install - drill diameter same as anchor diameter, hammer the pin til flush with head.<br />
• Tamperproof<br />
• Can be used in concrete, block, brick or stone<br />
• Mushroom head style<br />
• Carbon steel body / Steel pin<br />
• CAUTION: Nail-In Hammer Drive Anchors are not recommended for structural or overhead applications.<br />
SIZE MAX. THICKNESS MIN.<br />
PART# DIA X LENGTH DRILL DIA. OF FIXTURE (IN) EMBEDMENT (IN) QTY.<br />
120121 3/16 X 7/8 3/16 1/4 5/8 100<br />
120122 1/4 X 3/4 1/4 1/8 5/8 50<br />
120123 1/4 X 1 1/4 1/4 3/4 50<br />
120124 1/4 X 1-1/4 1/4 1/2 3/4 50<br />
120125 1/4 X 1-1/2 1/4 3/4 3/4 25<br />
120126 1/4 X 2 1/4 1-1/4 3/4 25<br />
Nylon Tap-It Anchors<br />
• Light duty fastening in masonry or concrete.<br />
• Slotted head on nail for easy removal.<br />
• Hole size same as anchor diameter.<br />
• 100% Virgin Nylon.<br />
SUGGESTED APPLICATIONS:<br />
• Signs • Conduit Clamps • Bathroom Fixtures<br />
• Shelving • Control Panels • Electrical Fixtures<br />
• Fixtures<br />
• Pegboards<br />
• Truck Bodies • Pictures<br />
Wall Hook<br />
• Hang signs, maps, charts, calendars, diagrams.<br />
• Use with #6 through #14 screws.<br />
PART # QTY.<br />
10435 25<br />
Anchor <strong>Fasteners</strong><br />
PART #00751<br />
Found on Page 66<br />
PART #00441<br />
Found on Page 66<br />
Available in<br />
an Assortment<br />
Round Head Flat Head Mushroom Head<br />
HEAD STYLE HEAD STYLE HEADSTYLE<br />
SIZE ROUND HEAD QTY FLAT HEAD QTY MUSHROOM HEAD QTY<br />
3/16 X 3/4 06517 50<br />
3/16 X 1 06509 50 06513 50 06518 50<br />
3/16 X 1-1/2 06510 50 06514 50<br />
1/4 X 3/4 06520 50<br />
1/4 X 1 06511 50 06515 50 06521 50<br />
1/4 X 1-1/2 06512 50 06516 50 160120 50<br />
1/4 X 2 160116 50 160117 50 06522 25<br />
1/4 X 3 06523 25<br />
1/4 X 4 160123 25<br />
1 800 458-4018 www.uzengprod.com<br />
PART #00751KP<br />
Found on Page 66<br />
PART #00441KP<br />
Found on Page 66<br />
215<br />
FASTENERS
FASTENERS<br />
216<br />
Anchor <strong>Fasteners</strong><br />
Mas-Block Anchoring System<br />
The fast, easy two-step fastening system for concrete, block and brick<br />
MAS-BLOCK CONCRETE SCREWS MAKE OLD-FASHIONED MASONRY FASTENING SYSTEMS OBSOLETE!<br />
FEATURES: BENEFITS:<br />
• Strong • Specially hardened carbon steel. All threads “tap” into the masonry, providing<br />
exceptional holding power.<br />
• Fast • No need to prespot anchor locations. Drill and drive with same tool. Notched<br />
cutting edges on threads allow quick and easy threading into masonry materials.<br />
• Safe • No powder - actuated tools necessary. Fireproof - No lead or plastic components<br />
that can melt.<br />
• Versatile • Available in Phillips flat head for countersunk applications and combination hex<br />
washer head for neat, positive attachments in a wide variety of installations. Blue<br />
CR-10 fluorocarbon coating is TEN times more corrosion resistant than zinc.<br />
Can be installed closer to edge of slab. Removable - can be reinstalled in same<br />
hole. Replaces expansion anchors, powder actuated fasteners, plugs and screws.<br />
TYPICAL APPLICATIONS:<br />
• Door & Window Units • Flashing & Trim • Shutters<br />
• Outdoor Signs & Letters • Electrical Components • Surface Duct & Raceways<br />
• Telephone & Telegraph Equipment • Smoke & Fire Detectors • Lighting Fixtures<br />
• Base Angles & Channel Members • HVAC Components • Alarm Systems<br />
• Furring Strips & Wood Studs • Gutters and Downspouts • Roof Insulation<br />
1 800 458-4018 www.uzengprod.com
Mas-Block Anchors<br />
SLTD Phillips<br />
Hex Washer Head Flat Head<br />
HEAD HEAD<br />
STYLE DIA. LENGTH PART # QTY. STYLE DIA. LENGTH PART # QTY.<br />
1-1/4 07522 50 1-1/4 07536 50<br />
SLTD 1-3/4 07523 50 SLTD 1-3/4 07537 50<br />
HEX 2-1/4 07524 50 HEX 2-1/4 07538 50<br />
WASHER 3/16" 2-3/4 07525 50 WASHER 1/4” 2-3/4 07539 50<br />
HEAD 3-1/4 07526 25 HEAD 3-1/4 07540 25<br />
(1/4 HEX SIZE) 3-3/4 07527 25 (5/16 HEX SIZE) 3-3/4 07541 25<br />
4 07528 25 4 07542 25<br />
1-1/4 07529 50 1-1/4 07543 50<br />
1-3/4 07530 50 1-3/4 07544 50<br />
PHILLIPS 2-1/4 07531 50 PHILLIPS 2-1/4 07545 50<br />
FLAT 3/16" 2-3/4 07532 50 FLAT 1/4” 2-3/4 07546 50<br />
HEAD 3-1/4 07533 25 HEAD 3-1/4 07547 25<br />
(#2 PHILLIPS BIT) 3-3/4 07534 25 (#3 PHILLIPS BIT) 3-3/4 07548 25<br />
4 07535 25 4 07549 25<br />
Mas-Block Installation Tool Kit - Drill and Drive Mas-Block Carbide -Tipped Masonry Bits<br />
Mas-Block Anchors with the same tool. Use with All Pack QTY. 1 - order separately<br />
and 3/8” or 1/2” Standard Hammer or Rotary Drill.<br />
COMPLETE KIT # 90005<br />
Contains everything shown<br />
Mas-Block Fastener Selection Guide<br />
(A) FIXTURE (B) MAS-BLOCK (C) DEPTH OF BIT *<br />
THICKNESS LENGTH DRILLED HOLE LENGTH<br />
0-1/4" 1-1/4" 1-1/2" 4-1/2"<br />
1/4"- 3/4" 1-3/4" 2" 4-1/2"<br />
3/4" - 1-1/4" 2-1/4" 2-1/2" 4-1/2"<br />
1-1/4"- 1-3/4" 2-3/4" 3" 4-1/4"<br />
3-3/4" - 2-1/4" 3-1/4" 3-1/2" 5-1/2"<br />
2-1/4" - 2-3/4" 3-3/4" 4" 5-1/2"<br />
2-1/2" - 3" 4" 4-1/4" 5-1/2"<br />
* 5/32" diameter drill bit for 3/16" diameter drill bit for 1/4" anchor<br />
DRILL USE WITH<br />
DIA. LENGTH SCREW DIA. PART #<br />
5/32<br />
5/32<br />
4-1/2<br />
5-1/2<br />
3/16"<br />
07558<br />
07559<br />
3/16<br />
3/16<br />
4-1/2<br />
5-1/2<br />
1/4"<br />
07560<br />
07561<br />
Available in<br />
an Assortment<br />
Anchor <strong>Fasteners</strong><br />
PART # 103632<br />
Found on Page 62<br />
PART # 00583<br />
Found on Page 67<br />
PART # 00584<br />
Found on Page 67<br />
PART # 00585<br />
Found on Page 67<br />
1 800 458-4018 www.uzengprod.com<br />
217<br />
FASTENERS
FASTENERS<br />
218<br />
Rivet <strong>Fasteners</strong><br />
Rivet and Mandrel Information<br />
Rivet and Mandrel materials may be the same or different. To make your<br />
selection easier, we have used the following arrangement:<br />
The Rivet Material is always shown first<br />
The mandrel material is always shown last<br />
CODE RIVET MANDREL<br />
A/S Aluminum Steel<br />
A/A Aluminum Aluminum<br />
S/S Steel Steel<br />
C/S Copper Steel<br />
SS/S Stainless Steel Steel<br />
SS/SS Stainless Steel Stainless Steel<br />
Head Style Selection Chart<br />
Dome Head Use Dome Head Rivets in normal<br />
applications. As shown, the finished<br />
rivet protrudes above the surface of<br />
the work with a normal head diameter.<br />
Countersunk Use 120° Countersunk Rivets in<br />
applications where a flush appearance<br />
is needed. Keep in mind that the<br />
preparation includes drilling the hole<br />
and countersinking it. Countersinking<br />
may not be necessary in very soft<br />
material such as soft wood, some<br />
plastics, etc.<br />
Rivet Size Chart<br />
Actual Rivet Size<br />
Grip Range<br />
3/32<br />
DIA<br />
1-1/8<br />
1/8-1/4<br />
GRIP RANGE<br />
1/4<br />
DIA<br />
0-1/4<br />
1/8<br />
DIA<br />
1/4-3/8<br />
0-1/16<br />
1/16-1/8<br />
1/8-3/16<br />
3/16-1/4<br />
1/4-5/16<br />
5/16-3/8<br />
3/8-1/2<br />
1/2-5/8<br />
3/8-1/2<br />
5/8-3/4<br />
1 800 458-4018 www.uzengprod.com<br />
5/32<br />
DIA<br />
Grip range after head is drawn<br />
(Total thickness of material to be joined)<br />
Large Flange Use Large Flange Rivets in applications where<br />
a larger bearing surface is required. This larger<br />
bearing surface will cover up blemishes around<br />
the hole as well as off-center holes. More<br />
importantly, this head style adds strength and<br />
stability to weak or thin joints and reduces the<br />
possibility of “pull-through."<br />
0-1/8<br />
1/8-3/16<br />
3/16-1/4<br />
1/4-3/8<br />
HOLE PREPARATION DATA:<br />
RIVET DIA. HOLE SIZE USE DRILL SIZE<br />
3/32 .098 #40<br />
1/8 .128 - .132 #30<br />
5/32 .160 - .164 #20<br />
3/16 .192 - .196 #11<br />
1/4 .257 - .261 Letter “F”<br />
3/8-1/2<br />
Rivet<br />
1/2-5/8<br />
3/16<br />
DIA<br />
0-1/8<br />
Mandrel<br />
1/8-1/4<br />
1/4-3/8<br />
3/8-1/2<br />
1/2-5/8<br />
FOR EASY RIVET SELECTION:<br />
To make your rivet selection easier, follow these rules:<br />
1. Select the DIAMETER and HEAD STYLE you need<br />
2. Select the GRIP RANGE you require<br />
3. Follow the GRIP RANGE size to the right and<br />
select the correct<br />
RIVET AND MANDREL MATERIAL:<br />
1. The PART NUMBER will be shown in that block<br />
on the display page<br />
5/8-3/4
Blind Rivets<br />
The rivet with built-in features that ordinary blind rivets cannot give you!<br />
• Complete Hole Fill<br />
The bulbing formation of the will fill slightly oversized or<br />
irregular holes, providing increased strength and vibration resistance.<br />
• Wide Grip Range<br />
One rivet can be used in multiple thicknesses. This reduces<br />
inventories and eliminates operator error.<br />
• Mechanically Locked Stem<br />
Stem is locked in shell, eliminating the risk of mandrel head<br />
vibrating loose while providing a weather resistant joint.<br />
• Water Tight<br />
As the rivet “flows” behind and in front of the mandrel, the<br />
stem is positively sealed to eliminate damage from rust, corrosion<br />
and other type of water damage.<br />
Can be used in...<br />
• Steel • Wood • Stainless Steel<br />
• Aluminum • Fiberglass • Leather<br />
• Plastic • Particle Board • Compositions<br />
Rivets can be used virtually anywhere that two materials must be permanently and securely joined together...<br />
• Truck Bodies • Air Conditioning • Partitions<br />
• Mobile Homes • Refrigeration • Panels<br />
• Recreational Vehicles • Electrical Equipment • Fixtures<br />
• Snowmobiles • Boats • Machinery Guards<br />
• Dune Buggies • Duct Work • etc...<br />
Specifications:<br />
MATERIALS: Rivet - Aluminum, uncoated<br />
Stem - Steel, zinc yellow dichromate treated<br />
Installed Strength Values<br />
RIVET DIA. TENSILE STRENGTH SHEAR STRENGTH<br />
1/8 230 lbs. 165 lbs.<br />
5/32 375 lbs. 255 lbs.<br />
3/16 530 lbs. 350 lbs<br />
Rivet <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
219<br />
FASTENERS
FASTENERS<br />
220<br />
Rivet <strong>Fasteners</strong><br />
Blind Rivets<br />
Aluminum Body with Steel Zinc Yellow Stem<br />
HEAD PART RIVET GRIP HOLE DRILL HEAD HEAD<br />
STYLE # QTY. DIA. RANGE SIZE SIZE DIA. HEIGHT<br />
70231 100 1/8 .031 - .187 .128 - .133 #29 .252 .051<br />
LOW 70232 100 1/8 .125 - .312 .128 - .133 #29 .252 .051<br />
PROFILE 70233 100 5/32 .046 - .250 .161 - .166 #19 .311 .061<br />
70234 50 3/16 .062 - .250 .194 - .199 #8 .387 .071<br />
70235 50 3/16 .187 - .437 .194 - .199 #8 .387 .071<br />
70236 100 1/8 .031 - .187 .128 - .133 #29 .325 .045<br />
70237 100 1/8 .125 - .312 .128 - .133 #29 .325 .045<br />
LARGE 70238 100 5/32 .125 - .312 .161 - .166 #19 .375 .058<br />
FLANGE 70239 50 3/16 .062 - .250 .194 - .199 #8 .625 .075<br />
70240 50 3/16 .250 - .500 .194 - .199 #8 .625 .075<br />
70241 50 3/16 .500 - .781 .194 - .199 #8 .625 .075<br />
70242 100 1/8 .031 - .187 .128 - .133 #29 .252 .051<br />
70243 100 1/8 .125 - .312 .128 - .133 #29 .252 .051<br />
DOME 70244 100 5/32 .046 - .250 .161 - .166 #19 .311 .061<br />
70245 50 3/16 .062 - .250 .194 - .199 #8 .387 .071<br />
70246 50 3/16 .187 - .437 .194 - .199 #8 .387 .071<br />
120° 120110 100 1/8 .093 - .250 .128 - .133 #29 .207 .050<br />
COUNTER 120111 100 5/32 .155 - .312 .161 - .166 #19 .247 .052<br />
SUNK 120113 50 3/16 .250 - .500 .194 - .199 #8 .347 .069<br />
Steel Blind Rivets<br />
Low carbon steel-zinc plated body with high tensile steel phosphate coated stem<br />
• High strength value.<br />
• Low profile head.<br />
RIVET GRIP DRILL HEAD HEAD TENSILE SHEAR<br />
PART # QTY. DIA RANGE SIZE DIA. HEIGHT STRENGTH STRENGTH<br />
70247 50 1/8 .044 - .156 #30 .295 .036 385 lbs. 340 lbs.<br />
70248 50 3/16 .047 - .187 #10 .395 .073 750 lbs. 810 lbs.<br />
70249 50 3/16 .156 - .250 #10 .395 .073 780 lbs. 1025 lbs<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #00502<br />
Found on Page 68<br />
PART #00503<br />
Found on Page 68
Aluminum Flare Grip Rivets<br />
...The Rivet That Works Like A Toggle Bolt!<br />
• Ideal for joining soft, brittle, thick or clad materials.<br />
• Like a Toggle Bolt, it forms a large bearing surface to<br />
provide exceptionally high “Pull-Through” values.<br />
• All aluminum for light weight, high strength and good<br />
corrosion resistance.<br />
• Each size has an extended grip range, so only five sizes are<br />
required to cover a wide range of material thicknesses.<br />
• Can be easily installed with a manual rivet installation tool.<br />
Here's how it works...<br />
1. Insert rivet 2. Three uniform segments 3. The segments continue to fold<br />
prepared hole. begin to fold outward and the stem breaks off...<br />
with the initial pull. Installation is complete.<br />
Check out the outstanding features and benefits of the Flare Grip Rivet!<br />
Can you use it in your operation?<br />
• Compensates for oversized holes.<br />
• Large blindside bearing surface.<br />
• Stem positively retained.<br />
• Flush mandrel break.<br />
• Excellent clamp-up.<br />
• Smaller blindside clearance than similar function fasteners.<br />
Wide Grip Range!<br />
Each Flare Grip Rivet easily handles a wide range of material thicknesses,<br />
from .063" to .250" to help reduce your inventory!<br />
Rivet <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
221<br />
FASTENERS
FASTENERS<br />
222<br />
Rivet <strong>Fasteners</strong><br />
Flare Grip Rivet Specifications and Ordering Information<br />
Shell: Aluminum<br />
Stem: Aluminum<br />
"GR" NOMINAL "H"<br />
“D” GRIP GRIP HEAD “L” HOLE DRILL SHEAR TENSILE<br />
DIA. PART # QTY. DIA. RANGE RANGE HEIGHT LENGTH DIA. SIZE STRENGTH STRENGTH<br />
5/32 122670 100 .162 .040/.118 3/64-7/64 .060 .620 .165/.177 #19 135lb. 225lb.<br />
70310 50 .162 .040/.275 3/64-19/64 .060 .840 .165/.177 #19 135lb. 225lb.<br />
70311 50 .195 .040/.118 3/64-5/32 .080 .720 .197/.207 #8 175lb. 240lb.<br />
3/16 70312 50 .195 .040/.354 9/64-11/32 .080 .920 .197/.207 #8 175lb. 240lb<br />
122671 50 .195 .157/.472 5/32-15/32 .080 1.07 .197/.207 #8 175lb. 240lb.<br />
Rivet Tool Heavy Duty Manual Riveting Tool<br />
• Designed to place all sizes of rivets as well as conventional<br />
breakstem rivets in 1/8", 5/32" and 3/16" diameters.<br />
• Long handles allow even the largest sizes of steel rivets<br />
to be installed with ease and efficiency.<br />
• High strength formed steel construction eliminates the<br />
inherent weakness of cast parts, as found in many other<br />
breakstem rivet tools.<br />
• Storage on tool for nose bushings not in use.<br />
• Overall length 10-1/2".<br />
• Includes one of each nose bushing<br />
(90406, 90407, 90408 and 90409).<br />
Nose Bushings for Riveter<br />
PART # DESCRIPTION QTY.<br />
90406 1/8" Diameter Rivets 1<br />
90407 5/32" Diameter Rivets 1<br />
90408 3/16" Diameter Rivets 1<br />
90409 Steel Rivets 1<br />
90715 3/16" Diameter Monobolts 1<br />
1 800 458-4018 www.uzengprod.com<br />
P<br />
H<br />
L<br />
D<br />
GR<br />
Available in<br />
an Assortment<br />
PART # 00768<br />
Found on Page 68<br />
PART # 00769<br />
Found on Page 69<br />
PART # 90405
<strong>UZ</strong> Blind Rivet System<br />
<strong>UZ</strong> Dome Head Rivets<br />
• <strong>UZ</strong> Blind Rivets meet or 1/8 Diameter<br />
exceed IFI Spec. #114<br />
standards.<br />
• Secure fastening of thin and 5/32 Diameter<br />
thick applications and hard<br />
and soft materials.<br />
• Low in-place cost. 3/16 Diameter<br />
• Vibration and tamper resistant.<br />
• Will not harm painted or other<br />
1/4 Diameter<br />
finished surfaces.<br />
*Denotes product which covers 2 grip ranges<br />
Available in<br />
an Assortment<br />
Rivets <strong>Fasteners</strong><br />
<strong>UZ</strong> Dome Head Rivets<br />
are the most popular for industrial<br />
applications. The low profile head<br />
diameter is twice the rivet body<br />
diameter, providing adequate<br />
bearing for nearly all applications.<br />
PART # PART # PART # STAINLESS RIVET<br />
GRIP STEEL RIVET ALUMINUM RIVET ALUMINUM RIVET STAINLESS MANDREL<br />
DIAMETER RANGE STEEL MANDREL ALUMINUM MANDREL STEEL MANDREL 18-8 STAINLESS QTY.<br />
1/32-1/16 70385 70320 70418* 100<br />
1/16-1/8 70386 70321 70353 70418* 100<br />
DIA. 1/8" 1/8-3/16 70387 70322 70354 70419 100<br />
DRILL#30 3/16-1/4 70388 70323 70355 70420 100<br />
.129-.133 1/4-5/16 70389 70324 70356 70421* 100<br />
5/16-3/8 70390 70325 70357 70421* 100<br />
3/8-1/2 70391 70326 70358 70422 100<br />
1/16-1/8 70392 70327 70359 70423 100<br />
DIA. 5/32" 1/8-3/16 70393 70328 70360 70424* 100<br />
DRILL #11 3/16-1/4 70394 70329 70361 70424* 100<br />
.160-.164 1/4-3/8 70395 70330 70362 70425 100<br />
3/8-1/2 70396 70331 70363 100<br />
1/16-1/8 70397 70332 70364 70426 100<br />
1/8-1/4 70398 70333 70365 70427 100<br />
DIA. 3/16" 1/4-3/8 70399 70334 70366 70428 100<br />
DRILL #11 3/8-1/2 70400 70335 70367 70429 100<br />
.192-.196 1/2-5/8 70401 70336 70368 100<br />
5/8-3/4 70402 70337 70369 100<br />
3/4-7/8 70432 70434 100<br />
7/8-1 70433 70435 100<br />
1/16-1/4 70403 70338 70370 50<br />
DIA. 1/4" 1/4-3/8 70404 70339 70371 50<br />
DRILL F 3/8-1/2 70405 70340 70372 50<br />
.257-.261 1/2-5/8 70406 70341 70373 50<br />
5/8-3/4 70407 70342 70374 50<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00749<br />
Found on Page 69<br />
223<br />
FASTENERS
FASTENERS<br />
224<br />
Rivet <strong>Fasteners</strong><br />
<strong>UZ</strong> Blind Rivet System<br />
<strong>UZ</strong> Large Flange Rivets<br />
1/8 Diameter 3/16 Diameter<br />
<strong>UZ</strong> 120° Countersunk Rivets<br />
1/8 Diameter<br />
1 800 458-4018 www.uzengprod.com<br />
<strong>UZ</strong> Large Flange Rivets<br />
provide greater bearing surface<br />
for fastening soft and brittle<br />
plywood and plastics including<br />
neoprene, vinyl, etc.<br />
PART # PART # PART #<br />
GRIP STEEL RIVET ALUMINUM RIVET ALUMINUM RIVET<br />
DIAMETER RANGE STEEL MANDREL ALUMINUM MANDREL STEEL MANDREL QTY.<br />
DIA. 1/8" 1/32-1/8 70408 70343 70375 100<br />
DRILL #30 1/8-1/4 70409 70344 70376 100<br />
.129-.133 3/16-1/4 120237 500<br />
1/16-1/4 70410 70345 70377 100<br />
DIA. 3/16" 1/4-3/8 70411 70346 70378 100<br />
DRILL #11 3/8-1/2 70412 70347 70379 100<br />
.192-.196 1/2-5/8 70413 70348 70380 100<br />
5/8-3/4 70414 70349 70381 100<br />
<strong>UZ</strong> 120° Countersunk Rivets<br />
are for applications where a flush<br />
appearance is required.<br />
PART # PART # PART #<br />
GRIP STEEL RIVET ALUMINUM RIVET ALUMINUM RIVET<br />
DIAMETER RANGE STEEL MANDREL ALUMINUM MANDREL STEEL MANDREL QTY.<br />
DIA. 1/8" 1/16-1/8 70415 70350 70382 100<br />
DRILL #30 1/8-3/16 70416 70351 70383 100<br />
.129-.133 3/16-1/4 70417 70352 70384 100
<strong>UZ</strong> Blind Rivet System<br />
<strong>UZ</strong> “Extra-Length” Blind Rivets (Dome Head)<br />
RANGE PART # QTY.<br />
DIA. 118 (3mm) 1/2 - 19/32 70441 25<br />
DRILL 1/8” 19/32 - 11/16 70442 25<br />
.125 - .129<br />
USE 1/8 Nosepiece<br />
11/16 - 7/8 70443 25<br />
GRIP RANGE PART # QTY.<br />
DIA .157 (4mm) 1/2 - 19/32 70444 25<br />
DRILL #20 19/32 - 11/16 70445 25<br />
.160 - .164<br />
USE 5/32 Nosepiece<br />
11/16 - 7/8 70446 25<br />
RANGE PART # QTY.<br />
1-1-3/16 70447 25<br />
1-3/16 - 1-3/8 70448 25<br />
DIA .197 (5mm) 1-3/8 - 1-9/16 70449 25<br />
DRILL #7 1-9/16 - 1-3/4 70450 25<br />
.200 - .204 1-3/4 - 1-15/16 70451 25<br />
USE 3/16 Nosepiece 1-15/16 - 2-5/32 70452 25<br />
2-5/32 - 2-11/32 70453 25<br />
2-11/32 - 2-15/16 70454 25<br />
<strong>UZ</strong> Backup Washers (1/16" thick) for Reinforcement<br />
HOLE OUTSIDE USE WITH<br />
MATERIAL SHAPE SIZE PART # DIAMETER RIVET SIZE QTY.<br />
STEEL SQUARE .129" - .133" 70456 1/2 1/8 100<br />
.192" - .196" 70458 1/2 3/16 100<br />
.257" - .261" 70459 1/2 1/4 100<br />
STEEL ROUND .129" - .133" 70460 3/8 1/8 100<br />
.192" - .196" 70461 1/2 3/16 100<br />
ALUM. ROUND .129" - .133" 70462 3/8 1/8 100<br />
.160" - .164" 70463 7/16 5/32 100<br />
.192" - .196" 70464 1/2 3/16 100<br />
Rivet <strong>Fasteners</strong><br />
ALUMINUM RIVET-STEEL MANDREL<br />
(ZINC CLEAR DICHROMATE PLATED)<br />
3 mm 4mm 5mm<br />
.118 .157 .197<br />
APPLICATIONS:<br />
• Mount Signs.<br />
• Hinge Pins.<br />
• Circuit & board standoff mount.<br />
• GM carburetor clamp.<br />
• Bracket clamping.<br />
Washer Reinforcement<br />
1 800 458-4018 www.uzengprod.com<br />
225<br />
FASTENERS
FASTENERS<br />
226<br />
Rivet <strong>Fasteners</strong><br />
Cherry-Mates ®<br />
A two-piece non-structural fastening system for those really tough, “sandwich-type” (long grip) applications.<br />
H DIA.<br />
W DIA. D DIA.<br />
E<br />
L1<br />
BENEFITS:<br />
• Extra wide grip range - Thickness of material may be as much as 2-3/4”<br />
• Controlled clamp-up - Clamps tightly...but without crushing.<br />
• Tamper-proof - Smooth, low profile heads on both ends.<br />
• Non-critical holes - No close-tolerance drilling necessary.<br />
• Vibration-proof - Won’t shake loose.<br />
• Good tensile strength - Alum/Alum 250 lbs. Alum/Steel 450 lbs.<br />
1 800 458-4018 www.uzengprod.com<br />
L 2<br />
D DIA.<br />
"G"<br />
Total<br />
Material<br />
Thickness<br />
H DIA.<br />
BLIND RIVET TUBULAR COMPONENT<br />
BLIND RIVET TUBULAR COMP.<br />
NOM. HOLE SIZE W D H E D H E<br />
RIVET AND MAND. RIVET HEAD HEAD RIVET HEAD HEAD<br />
DIA. DRILL NUMBER DIA. DIA. DIA. THICK DIA. DIA. THICK.<br />
3/16 .250 (1/4) .076 .125 .375 .059 .188 .375 .057<br />
1/4 .312 (5/16) .114 .187 .625 .095 .250 .625 .095<br />
Tublar<br />
Component<br />
BLIND RIVET<br />
BLIND RIVET ALUM. SLEEVE<br />
G L L ALUM. SLEEVE STEEL MANDREL<br />
RIVET RIVET RIVET COMP ALUM. MANDREL PLATED<br />
DIA. GRIP LENGTH LENGTH TUBULAR COMP. TUBULAR COMP.<br />
RANGE (MAX) (MAX) ALUMINUM ALUMINUM QTY.<br />
PART # PART #<br />
3/16<br />
5/8" to 3/4" .525 .585 70548 50<br />
11/16" to 7/8" .525 .647 70549 50<br />
5/8" to 3/4" .454 .580 70550 70557 25<br />
3/4" to 7/8" .608 .695 70551 70558 25<br />
7/8" to 1-1/8" .608 .820 70552 70559 25<br />
1-1/8" to 1-3/8" .608 1.070 70553 70560 25<br />
1/4 1-3/8" to 1-5/8" .608 1.320 70554 70561 25<br />
1-5/8" to 1-7/8" .608 1.570 70555 70562 25<br />
1-7/8" to 2-1/8" .608 1.820 120736 70563 25<br />
2-1/8" to 2-3/8" .608 2.070 120737 70564 25<br />
2-3/8" to 2-5/8" .608 2.320 70556 25<br />
Blind<br />
Rivet<br />
TYPICAL END USES:<br />
• Signs<br />
• Pivoting Applications<br />
• Folding Tables<br />
• Restroom Partitions<br />
• Door Repair<br />
"G"<br />
Total<br />
Material<br />
Thickness<br />
Tublar<br />
Component<br />
Blind<br />
Rivet
Monobolt Advantages and Benefits<br />
Multi-Grip:<br />
One size Monobolt<br />
fastener will function effectively in a<br />
wide range of material thicknesses.<br />
(Example: .80” to .375”). This versatility<br />
decreases the potential for production<br />
errors and reduces fastener inventory<br />
requirements.<br />
Flush Break System:<br />
Within the specific grip range for each size<br />
Monobolt fastener, the stem is designed<br />
to break flush with the low profile head.<br />
Secondary finishing operations, such<br />
as grinding or milling, are not necessary<br />
to achieve good finished appearance.<br />
Positive Stem Retention:<br />
At the completion of the installation cycle,<br />
the stem is mechanically locked into the<br />
Monobolt shell, creating a<br />
vibration-proof joint of assured<br />
structural quality.<br />
Uniform Clamping Action:<br />
Monobolt fasteners are engineered to<br />
draw materials together by developing<br />
positive clamping action.<br />
Hundreds of applications need Monobolts for strength & economy!<br />
Truck Trailers<br />
APPLICATION:<br />
Attachment of exterior panels to cargo trailer<br />
frames.<br />
PREVIOUS METHODS:<br />
Solid riveting or two piece through bolting.<br />
RESULT:<br />
Maintenance time has been reduced.<br />
Electrical Enclosures<br />
APPLICATION:<br />
Assembly of cabinet framework and<br />
enclosure panels.<br />
PREVIOUS METHODS:<br />
Welded construction.<br />
RESULT:<br />
A reduction in maintenance costs.<br />
Ventilation Systems<br />
APPLICATION:<br />
Rebuilding of industrial blower wheels,<br />
heavy duct work and louvers.<br />
PREVIOUS METHODS:<br />
Two piece lock bolts or solid rivets.<br />
RESULT:<br />
Vibration-proof repairs achieved.<br />
Pre-Fab Structures<br />
APPLICATION:<br />
Field assembly of roof and side panels to<br />
structural members.<br />
PREVIOUS METHODS:<br />
Conventional metal building drive screw<br />
systems or through bolting.<br />
RESULT:<br />
The tamper resistant aspect of Monobolt<br />
discourages vandalism.<br />
Rivet <strong>Fasteners</strong><br />
Blind Installation:<br />
The single side installation feature of the<br />
Monobolt system allows one operator to<br />
produce high quality structural joints in<br />
seconds.<br />
Complete Hole Fill:<br />
During installation, the Monobolt shell<br />
expands into 360 degrees contact with the<br />
walls of the parent material. This feature, in<br />
conjunction with position stem retention,<br />
produces weather resistant joints.<br />
Structural Fastening:<br />
An installed Monobolt fastener yields high<br />
shear and tensile values. Conventional<br />
fasteners can be replaced by Monobolt<br />
strength requirements.<br />
Mass Transit Vehicles<br />
APPLICATION:<br />
Fastening exterior rub rails, side and roof<br />
panels to vehicle frames.<br />
PREVIOUS METHODS:<br />
Solid riveting requiring two men to<br />
complete each joint.<br />
RESULT:<br />
The productivity improves; one man gets<br />
the job done.<br />
Heavy Equipment<br />
APPLICATION:<br />
Joining roof sections, side panels and floor<br />
plates to cab frames.<br />
PREVIOUS METHODS:<br />
Spot welding and loose hardware.<br />
RESULT:<br />
Repair costs have been cut due to the<br />
elimination of extra operations.<br />
1 800 458-4018 www.uzengprod.com<br />
227<br />
FASTENERS
FASTENERS<br />
228<br />
Rivet <strong>Fasteners</strong><br />
Monobolt ®<br />
• “RIVET” speed and convenience!<br />
“BOLT & NUT” strength and durability!<br />
• Wide range of usable material thicknesses<br />
cut down on inventory requirements!<br />
• Single-side installation for quick repairs in<br />
hard to reach areas! Monobolt fasteners are shipped lubricated.<br />
DO NOT DEGREASE!<br />
PART # DIA. HEAD STYLE NOM. GRIP MATERIAL LENGTH QTY.<br />
70280 3/16 BRAZIER .064 - .270 STEEL-ZINC 13/32 25<br />
70281 3/16 BRAZIER .214 - .420 STEEL-ZINC 17/32 25<br />
70282 3/16 BRAZIER .064 - .270 ALUMINUM 13/32 25<br />
70283 3/16 BRAZIER .214 - .420 ALUMINUM 17/32 25<br />
70284 1/4 BRAZIER .080 - .375 STEEL-ZINC 9/16 25<br />
70285 1/4 BRAZIER .080 - .625 STEEL-ZINC 27/32 25<br />
70286 1/4 BRAZIER .080 - .375 ALUMINUM 9/16 25<br />
70287 1/4 BRAZIER .080 - .625 ALUMINUM 27/32 25<br />
70288 1/4 100° COUNTERSUNK .125 - .475 STEEL 21/32 25<br />
70289 1/4 100° COUNTERSUNK .125 - .475 ALUMINUM 21/32 25<br />
70290 3/16 BRAZIER .064 - .270 STAINLESS STEEL 13/32 25<br />
70291 3/16 BRAZIER .064 - .420 STAINLESS STEEL 17/32 25<br />
70292 1/4 BRAZIER .080 - .375 STAINLESS STEEL 9/16 25<br />
1. The Monobolt fastener is loaded<br />
into the nose of the placing tool<br />
and inserted in a prepared hole.<br />
As the tool is actuated, the pulling<br />
jaws grip the Monobolt ® stem.<br />
Monobolt hand tool with three pieces:<br />
3/16" Dia. Monobolt Nose, 1/4" Dia. Monobolt Nose<br />
and Monobolt Setting Tool Nose pieces.<br />
PART # 90656 QTY. 1<br />
1 800 458-4018 www.uzengprod.com<br />
2. An axial pull draws the stem<br />
through the shell, expanding it<br />
radially. During this phase, the<br />
hole is completely filled and the<br />
work pieces are drawn together.<br />
3. When the stem reaches a predetermined<br />
position within the Monobolt shell, it<br />
separates flush with the head profile<br />
regardless of work piece thickness.<br />
Simultaneously, the stem section<br />
remaining in the shell is mechanically<br />
locked in place by the Monobolt ® tool.<br />
PART # NOSE PIECES QTY.<br />
90650 3/16" Monobolt Fastener 1<br />
90651 1/4" Monobolt Fastener 1<br />
90652 3/16" Standard Rivet 1<br />
90653 3/16" Steel Rivet 1<br />
90654 1/4" Conventional Rivet 1<br />
90655 1/4" “T” Rivet 1
Magna-Lok® Rivets<br />
• Superior locking strength<br />
• Forms a tight weather resistant seal<br />
• Most widely used repair style structural rivet<br />
• Uses for trailer repair<br />
• Head styles available: button(protruding),truss and countersunk<br />
• Material composition: S/S (steel/steel) or A/A (aluminum/aluminum)<br />
• Package quantity is 50<br />
<strong>UZ</strong> PART # HUCK # DIA. HEAD MATERIAL GRIP<br />
STYLE RANGE<br />
123555 MGLP-R6-4 3/16 BUTTON S/S .062-.270<br />
123556 MGLP-R6-E 3/16 BUTTON S/S .062-.437<br />
123557 MGLP-R6-7 3/16 BUTTON S/S .214-.437<br />
123558 MGLP-R8-6 1/4 BUTTON S/S .080-.375<br />
123559 MGLP-R8-10 1/4 BUTTON S/S .350-.625<br />
123560 MGLP-R8-E 1/4 BUTTON S/S .080-.625<br />
123561 MGLP-B6-4 3/16 BUTTON A/A .062-.270<br />
123562 MGLP-B6-E 3/16 BUTTON A/A .062-.437<br />
123563 MGLP-B8-6 1/4 BUTTON A/A .080-.375<br />
123564 MGLP-B8-E 1/4 BUTTON A/A .080-.625<br />
123565 MGLT-R6-E 3/16 TRUSS S/S .062-.437<br />
123566 MGLT-R8-6 1/4 TRUSS S/S .080.375<br />
123567 MGLT-B6-4 3/16 TRUSS A/A .062-.270<br />
123568 MGL100-R6-6 3/16 CTSK S/S .125-.331<br />
Rivet <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
229<br />
FASTENERS
FASTENERS<br />
230<br />
Rivet <strong>Fasteners</strong><br />
MAGNA-GRIP® Rivets and Collars<br />
• Most reliable wide grip fastening system, assures vibration resistance<br />
• System consists of a rivet and collar<br />
• Use for trailer repair<br />
• Consistent shear strength, clamping force and tensile strength.<br />
• Material - steel or aluminum<br />
• Head styles for the rivets : button , truss and rivet<br />
• Material used is steel and aluminum<br />
• Collars have 2 version : standard flange or wide flange.<br />
• Pkg. Qty is 50<br />
<strong>UZ</strong> PART # HUCK # DIA. HEAD MATERIAL GRIP<br />
STYLE RANGE<br />
123569 MGPB-R6-10G 3/16 BUTTON S/S .062-.625<br />
123570 MGPB-R6-20G 3/16 BUTTON S/S .062-1.25<br />
123571 MGPB-R8-10G 1/4 BUTTON S/S .062-.625<br />
123572 MGPB-R8-20G 1/4 BUTTON S/S .062-1.25<br />
123573 MGPB-E8-10 1/4 BUTTON A/A .062-.625<br />
123574 MGPT-R8-10G 1/4 TRUSS S/S .062-.625<br />
123575 MGPT-R8-20G 1/4 TRUSS S/S .312-1.25<br />
123576 MGP98T-R6-10G 3/16 RIVET S/S .062-.625<br />
123577 MGP98T-R6-20G 3/16 RIVET S/S .312-1.25<br />
123578 MGP98T-E6-10 3/16 RIVET A/A .062-.625<br />
<strong>UZ</strong> PART # HUCK # DIA. COLLARD<br />
STYLE<br />
MATERIAL<br />
123579 MGC-R6U 3/16 STD STEEL<br />
123580 MGC-F6 3/16 STD ALUM<br />
123581 MGCW-R6U 3/16 WIDE STEEL<br />
123582 MGCW-F6 3/16 WIDE ALUM<br />
123583 MGC-R8U 1/4 STD STEEL<br />
123584 MGC-F8 1/4 STD ALUM<br />
123585 MGCW-R8U 1/4 WIDE STEEL<br />
1 800 458-4018 www.uzengprod.com
Plated Retaining Rings Plain<br />
G B<br />
W<br />
Basic Internal Type Basic External Type<br />
HOUSING GROOVE GROOVE<br />
DIA. DIA. WIDTH<br />
PART # “B” “G” “W” QTY.<br />
70152 1/4S .268 .018 50<br />
121050 1/4L .330 .018 50<br />
70153 5/16 .330 .018 50<br />
70154 3/8 .397 .029 50<br />
70155 7/16 .461 .029 50<br />
70156 1/2 .530 .039 50<br />
70157 9/16 .596 .039 50<br />
70158 5/8 .665 .039 50<br />
70159 3/4 .796 .039 50<br />
70160 7/8 .931 .046 50<br />
70161 1 1.066 .046 50<br />
70162 1-1/16 1.130 .056 25<br />
70163 1-1/8 1.197 .056 25<br />
70164 1-1/4 1.330 .056 25<br />
70165 1-5/16 1.396 .056 25<br />
70166 1-3/8 1.461 .056 25<br />
70167 1-1/2 1.594 .056 25<br />
70317 1-9/16 1.656 .068 25<br />
70168 1-5/8 1.725 .068 25<br />
70169 1-3/4 1.858 .068 25<br />
70170 1-7/8 1.989 .068 25<br />
70171 2 2.122 .068 15<br />
70172 2-1/16 2.186 .086 15<br />
70173 2-1/8 2.251 .086 15<br />
70174 2-3/16 2.318 .086 15<br />
70175 2-1/4 2.382 .086 15<br />
70176 2-5/16 2.450 .086 15<br />
70177 2-3/8 2.517 .086 15<br />
70178 2-7/16 2.584 .086 15<br />
70179 2-1/2 2.648 .086 15<br />
Available in<br />
an Assortment<br />
PART # 00514<br />
Found on Page 70<br />
PART # 00515<br />
Found on Page 70<br />
PART # 00602<br />
Found on Page 70<br />
Retaining Ring <strong>Fasteners</strong><br />
G B<br />
W<br />
HOUSING GROOVE GROOVE<br />
DIA. DIA. WIDTH<br />
PART # “B” “G” “W” QTY.<br />
121065 1/8 .117 .012 50<br />
70180 5/32 .146 .012 50<br />
70181 3/16 .175 .018 50<br />
70182 1/4 .230 .029 50<br />
70183 5/16 .290 .029 50<br />
70184 3/8 .352 .029 50<br />
70185 7/16 .412 .029 50<br />
70186 1/2 .468 .039 50<br />
70187 9/16 .530 .039 50<br />
70188 5/8 .588 .039 50<br />
70189 11/16 .646 .046 25<br />
70190 3/4 .704 .046 25<br />
70191 13/16 .812 .046 25<br />
70192 7/8 .821 .046 25<br />
70193 15/16 .938 .046 25<br />
70194 1 .940 .046 25<br />
70195 1-1/8 1.059 .056 25<br />
70196 1-1/4 1.176 .056 25<br />
70197 1-5/16 1.232 .056 25<br />
70198 1-3/8 1.291 .056 25<br />
70199 1-1/2 1.406 .056 25<br />
70200 1-9/16 1.468 .068 25<br />
70201 1-5/8 1.529 .068 25<br />
70202 1-3/4 1.650 .068 25<br />
70203 1-7/8 1.769 .068 25<br />
70204 2 1.886 .068 15<br />
70205 2-1/16 1.946 .086 15<br />
70206 2-1/8 2.003 .086 15<br />
70207 2-5/32 2.032 .086 15<br />
70208 2-1/4 2.120 .086 15<br />
121086 2-1/2 2.360 .086 15<br />
1 800 458-4018 www.uzengprod.com<br />
231<br />
FASTENERS
FASTENERS<br />
232<br />
Retaining Ring <strong>Fasteners</strong><br />
“E” Retaining Rings Plain<br />
External “E” Type - Standard<br />
SHAFT RING RING GROOVE GROOVE<br />
DIA. CLEARANCE THICKNESS DIA. WIDTH<br />
PART # “S” “C” “T” “G” “W” QTY.<br />
70209 1/16 .156 .010 .052 .012 50<br />
70210 3/32 .187 .015 .074 .018 50<br />
70211 1/8 .230 .015 .095 .018 50<br />
70212 5/32 .282 .025 .116 .029 50<br />
70213 3/16 .335 50<br />
70214 1/4 .527 .025 .210 .029 50<br />
70215 5/16 .500 .025 .250 .029 50<br />
70216 3/8 .660 .035 .303 .039 50<br />
70217 7/16 .687 .035 .343 .039 50<br />
70218 1/2 .800 .042 .396 .046 50<br />
70219 5/8 .940 .042 .485 .046 25<br />
70220 3/4 1.120 .050 .580 .056 25<br />
70221 7/8 1.300 .050 .675 .056 25<br />
70222 1 1.500 .050 .835 .056 50<br />
121100 1-3/16 1.626 .062 1.079 .068 50<br />
121101 1-3/8 1.875 .062 1.230 .068 50<br />
External “E” Type - Extra Grip<br />
FOR APPLICATIONS WHICH REQUIRE GREATER HOLDING<br />
POWER THAN STANDARD “E” TYPE RINGS.<br />
SHAFT RING RING GROOVE GROOVE<br />
DIA. CLEARANCE THICKNESS DIA. WIDTH<br />
PART # “S” “C” “T” “G” “W” QTY.<br />
121106 3/32 .206 .015 .074 .018 100<br />
70223 1/8 .270 .015 .095 .018 100<br />
70224 3/16 .375 .025 .147 .029 50<br />
70225 1/4 .516 .025 .210 .029 50<br />
70226 5/16 .588 .035 .250 .039 50<br />
70227 3/8 .660 .035 .303 .039 50<br />
70228 7/16 .746 .035 .343 .039 50<br />
70229 1/2 .810 .042 .396 .046 50<br />
70230 9/16 .870 .042 .437 .046 50<br />
1 800 458-4018 www.uzengprod.com<br />
C<br />
T<br />
S<br />
W<br />
G<br />
C1<br />
Available in<br />
an Assortment<br />
PART # 00516<br />
Found on Page 71<br />
F
Retaining Ring Pliers<br />
• Internal and External Conversion.<br />
• Automatic Ratchet Lock.<br />
• Positive Tip Control - 12 Point Openings.<br />
PART # 70301<br />
INTERNAL 1-13/16"-4"<br />
31mm-100mm<br />
EXTERNAL 1-1/2"-4"<br />
31mm-100mm<br />
PART # 70300<br />
INTERNAL 3/8"-2"<br />
10mm-48mm<br />
EXTERNAL 1/4"-2"<br />
7mm-48mm<br />
PART # 70293<br />
INTERNAL 1/4"-1"<br />
8mm-26mm<br />
EXTERNAL 1/8"-1"<br />
3mm-26m<br />
Tips for Lock Rings All tips are packed in a plastic pouch<br />
#70297<br />
PAIR OF TIPS BENT<br />
15° For Model 70301<br />
Plier with Ratchet Lock.<br />
These tips have vee<br />
notches to service heavy<br />
section external beveled<br />
and lock rings.<br />
#70298<br />
PAIR OF TIPS BENT 15°<br />
For Model 70301 Plier<br />
with Ratchet Lock.<br />
These tips have flat<br />
ends to service heavy<br />
sections flat end lock<br />
rings, parallel end lock<br />
rings, horse shoe<br />
internal lock rings,<br />
and piston rings.<br />
#70299<br />
PAIR OF TIPS<br />
For Model 70301 Plier<br />
with Ratchet Lock.<br />
These tips have angled<br />
ends to expand reverse<br />
beveled external lock<br />
rings.<br />
Retaining Ring <strong>Fasteners</strong><br />
Replacement Tip Kit<br />
PART # 70303<br />
Three color coded pairs of tips in sizes .090,<br />
.108 and .120 bent 15 degrees in a plastic pouch.<br />
•Internal and External Conversion.<br />
•Replaceable Tips.<br />
Replacement Tip Kit<br />
PART # 70302<br />
Five color coded pairs of tips in sizes .0326, .047, and .070<br />
straight, and .036 and .047 bent 90 degrees in a plastic pouch.<br />
• Internal and External Conversion.<br />
• Replaceable Tips.<br />
Replacement Tip Kit<br />
PART # 70294<br />
Five color coded pairs of tips in sizes .023, .036, and .047<br />
straight, and .036 and .047 bent 90 degrees in plastic pouch.<br />
#70295<br />
PAIR OF TIPS BENT 15°<br />
For Models 70300 and<br />
70293 Pliers. These<br />
tips have vee notches<br />
to service light section<br />
beveled and external<br />
lock rings in automotive<br />
transmissions and<br />
front drives.<br />
#70296<br />
PAIR OF TIPS BENT 15°<br />
For Models 70300 and<br />
70293 Pliers. These tips<br />
have narrow elongated<br />
flat ends to service light<br />
section external lock rings<br />
in Ford & GM splined<br />
transmission shafts and<br />
to expand piston rings.<br />
1 800 458-4018 www.uzengprod.com<br />
233<br />
FASTENERS
FASTENERS<br />
234<br />
Cotter Pin <strong>Fasteners</strong><br />
Hammerlock Cotter Pins<br />
• Designed for maintenance use.<br />
• Manufactured to exacting standards.<br />
• Easier to use than conventional cotter pins.<br />
• Smooth & burr free for easy installation.<br />
• Uni-zinc plated.<br />
INSTALLATION:<br />
1. Insert pin in hole. 2. Hit head with a<br />
hammer to spread<br />
prongs.<br />
How cotter pins are measured.<br />
LENGTH:<br />
Measure from under the eye to the end of the longest prong.<br />
DIAMETER:<br />
Simply measure the diameter of both thicknesses.<br />
DIA. LENGTH PART # QTY.<br />
1/2 70089<strong>UZ</strong> 250<br />
3/4 70090<strong>UZ</strong> 250<br />
1 70091<strong>UZ</strong> 250<br />
1/16 1-1/4 70092<strong>UZ</strong> 200<br />
1-1/2 70093<strong>UZ</strong> 200<br />
1-3/4 70094 200<br />
2 70095 200<br />
1/2 70096 250<br />
3/4 70097<strong>UZ</strong> 250<br />
1 70098<strong>UZ</strong> 250<br />
3/32 1-1/4 70099<strong>UZ</strong> 250<br />
1-1/2 70100<strong>UZ</strong> 100<br />
1-3/4 70101 100<br />
2 70102 100<br />
2-1/2 70103 100<br />
1 116756 100<br />
7/64 1-1/2 116751 100<br />
2 116752 100<br />
1/2 70104 250<br />
3/4 70105<strong>UZ</strong> 250<br />
1/8 1 70106 100<br />
1-1/4 70107<strong>UZ</strong> 100<br />
1-1/2 70108 100<br />
1 800 458-4018 www.uzengprod.com<br />
3. Tap prongs with<br />
hammer to lock<br />
in place.<br />
DIA. LENGTH PART # QTY.<br />
1-3/4 70109 100<br />
1/8 2 70110 100<br />
2-1/2 70111<strong>UZ</strong> 50<br />
3 70112<strong>UZ</strong> 50<br />
3/4 70113<strong>UZ</strong> 100<br />
1 70114 100<br />
1-1/4 70115<strong>UZ</strong> 100<br />
5/32 1-1/2 70116 100<br />
1-3/4 70117 100<br />
2 70118 50<br />
2-1/2 70119 50<br />
3 70120 50<br />
1 70121 50<br />
1-1/2 70122 50<br />
3/16 2 70123 50<br />
2-1/2 70124 50<br />
3 70125 50<br />
3-1/2 70126 50<br />
4 70127 50<br />
1 70128 50<br />
1/4 1-1/2 70129 50<br />
2 70130 50<br />
2-1/2 70131 50<br />
Available in<br />
an Assortment<br />
PART #00512<br />
Found on Page 71<br />
DIA. LENGTH PART # QTY.<br />
3 70132 50<br />
1/4 3-1/2 70133 50<br />
4 70134 50<br />
1 70135 50<br />
1-1/2 70136 50<br />
2 70137 50<br />
5/16 2-1/2 70138 25<br />
3 70139 25<br />
3-1/2 70140 25<br />
4 70141 25<br />
2 70142 25<br />
2-1/2 113890 25<br />
3 70143 25<br />
3/8 4 70144 25<br />
5 70145 25<br />
6 70146 25<br />
2 70147* 25<br />
3 70148* 25<br />
1/2 4 70149* 20<br />
5 70150* 20<br />
6 70151* 20<br />
*Extended prong only
Spring Roll Pins<br />
• Easily Installed. • Chamfered Corners.<br />
• Heat Treated. • Self Locking.<br />
• Reusable. • Zinc Coated.<br />
DIA. LENGTH PART # QTY.<br />
3/16 120863 100<br />
1/4 70000 50<br />
3/8 70001 50<br />
1/16 1/2 70002 50<br />
(.062) 5/8 70003 50<br />
3/4 70004 50<br />
7/8 70005 50<br />
1 70006 50<br />
1/4 70007 50<br />
3/8 70008 50<br />
5/64 1/2 70009 50<br />
(.078) 5/8 70010 50<br />
3/4 70011 50<br />
7/8 70012<strong>UZ</strong> 50<br />
1 70013 50<br />
1/4 70014 50<br />
5/16 120885 100<br />
3/8 70015<strong>UZ</strong> 50<br />
1/2 70016 50<br />
3/32 5/8 70017 50<br />
(.094) 3/4 70018<strong>UZ</strong> 50<br />
7/8 70019 50<br />
1 70020<strong>UZ</strong> 50<br />
1-1/4 70021 50<br />
1-1/2 70022 50<br />
1/4 70023 50<br />
3/8 70024 50<br />
1/2 70025 50<br />
1/8 5/8 70026 50<br />
(.125) 3/4 70027 50<br />
7/8 70028 50<br />
1 70029 50<br />
1-1/4 70030 50<br />
1-1/2 70031 50<br />
2 120906 100<br />
1/2 70032<strong>UZ</strong> 50<br />
5/8 70033 50<br />
3/4 70034 50<br />
7/8 70035 50<br />
5/32 1 70036 50<br />
(.156) 1-1/4 70037<strong>UZ</strong> 50<br />
1-1/2 70038<strong>UZ</strong> 50<br />
1-3/4 70039<strong>UZ</strong> 50<br />
2 70040 50<br />
1/2 70041 50<br />
3/16 5/8 70042 50<br />
(.187) 3/4 70043 50<br />
7/8 70044 50<br />
Spring Roll Pin <strong>Fasteners</strong><br />
DIA. LENGTH PART # QTY.<br />
1 70045 50<br />
3/16 1-1/4 70046 25<br />
(.187) 1-1/2 70047 25<br />
1-3/4 70048 25<br />
2 70049 25<br />
5/8 120933 50<br />
3/4 70050 25<br />
7/8 70051 25<br />
1 70052 25<br />
7/32 1-1/4 70053 25<br />
(.219) 1-3/8 120934 50<br />
1-1/2 70054 25<br />
1-3/4 70055 25<br />
2 70056 25<br />
2-1/2 70057 25<br />
3/4 70058 25<br />
7/8 70059 25<br />
1 70060 25<br />
1/4 1-1/4 70061 25<br />
(.250) 1-1/2 70062 25<br />
1-3/4 70063 25<br />
2 70064 25<br />
2-1/2 70065 25<br />
3 70066<strong>UZ</strong> 25<br />
3/4 70067 25<br />
1 70069<strong>UZ</strong> 25<br />
1-1/2 70070<strong>UZ</strong> 25<br />
5/16 1-3/4 120958 25<br />
(.312) 2 70071<strong>UZ</strong> 25<br />
2-1/2 70072<strong>UZ</strong> 25<br />
3 70073<strong>UZ</strong> 25<br />
3/4 70074<strong>UZ</strong> 25<br />
1 70075<strong>UZ</strong> 25<br />
3/8 1-1/2 70076<strong>UZ</strong> 25<br />
(.375) 2 70077<strong>UZ</strong> 10<br />
2-1/2 70078<strong>UZ</strong> 10<br />
3 70079<strong>UZ</strong> 10<br />
1 70080<strong>UZ</strong> 10<br />
7/16 1-1/2 70081<strong>UZ</strong> 10<br />
(.437) 2 70082<strong>UZ</strong> 10<br />
2-1/2 70083<strong>UZ</strong> 10<br />
3 70084<strong>UZ</strong> 10<br />
1-1/2 70085 10<br />
1/2 2 70086 10<br />
(.500) 2-1/2 70087 10<br />
3 70088<strong>UZ</strong> 10<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #00510<br />
Found on Page 72<br />
PART #00511<br />
Found on Page 72<br />
235<br />
FASTENERS
FASTENERS<br />
236<br />
Clevis Pin <strong>Fasteners</strong><br />
Single Hole Clevis Pins<br />
• For use in applications where precise • Use with hammerlock or extending prong cotter<br />
pin lengths are required. pins for greater strength.<br />
• Low Carbon Steel.<br />
OVERALL EFFECTIVE<br />
DIAMETER LENGTH LENGTH PART # QTY.<br />
1/2 13/32 122100 10<br />
3/4 21/32 122101 10<br />
1 29/32 122102 10<br />
3/16 1-1/2 1-13/32 122103 10<br />
2 1-29/32 122104 10<br />
2-1/2 2-13/32 122105 10<br />
3 2-29/32 122106 10<br />
3/4 21/32 122108 10<br />
1 21/32 122109 10<br />
1-1/2 1-13/32 122110 10<br />
1-3/4 1-21/32 122111 10<br />
1/4 2 1-25/32 122112 10<br />
2-1/2 2-13/32 122113 10<br />
3 2-21/32 122114 10<br />
3-1/2 3-13/32 122115 10<br />
4 3-29/32 122116 10<br />
5 4-29/32 122117 10<br />
1/2 11/32 122118 10<br />
3/4 19/32 122119 10<br />
1 27/32 122120 10<br />
1-1/4 1-3/32 122121 10<br />
1-1/2 1-11/32 122122 10<br />
5/16 2 1-27/32 122123 10<br />
2-1/2 2-11/32 122124 10<br />
3 2-27/32 122125 10<br />
3-1/2 3-11/32 122126 10<br />
4 3-27/32 122127 10<br />
6 5-27/32 122128 10<br />
3/4 19/32 122129 10<br />
1 27/32 122130 10<br />
1-1/4 1-3/32 122131 10<br />
1-1/2 1-11/32 122132 10<br />
3/8 2 1-27/32 122133 10<br />
2-1/2 2-11/32 122134 10<br />
3 2-27/32 122135 10<br />
3-1/2 3-11/32 122136 10<br />
4 3-27/32 122137 10<br />
1 27/32 122138 10<br />
1-1/4 1-3/32 122139 10<br />
1-1/2 1-11/32 122140 10<br />
2 2-27/32 122141 10<br />
7/16 2-1/2 2-11/32 122142 10<br />
3 2-27/32 122143 10<br />
3-1/2 3-11/32 122144 10<br />
4 3-27/32 122145 10<br />
1 800 458-4018 www.uzengprod.com<br />
OVERALL EFFECTIVE<br />
DIAMETER LENGTH LENGTH PART # QTY.<br />
1 27/32 122146 10<br />
1-1/4 1-3/32 122147 10<br />
1-1/2 1-11/32 122148 10<br />
2 1-27/32 122149 10<br />
1/2 2-1/2 2-11/32 122150 10<br />
3 2-27/32 122151 10<br />
3-1/2 3-11/32 122152 10<br />
4 3-27/32 122153 10<br />
4-1/2 4-11/32 122154 10<br />
5 4-27/32 122155 10<br />
6 5-27/32 122156 10<br />
2 1-27/32 122157 5<br />
9/16 2-1/2 2-11/32 122158 5<br />
3 2-27/32 122159 5<br />
4 3-27/32 122160 5<br />
1-1/4 1-3/32 122161 5<br />
1-1/2 1-11/32 122162 5<br />
2 1-27/32 122163 5<br />
5/8 2-1/2 2-11/32 122164 5<br />
3 2-27/32 122165 5<br />
3-1/2 3-11/32 122166 5<br />
4 3-27/32 122167 5<br />
6 5-27/32 122168 5<br />
2-1/2 2-11/32 122170 5<br />
3 2-27/32 122171 5<br />
3-1/2 3-11/32 122172 5<br />
3/4 4 3-27/32 122173 5<br />
4-1/2 4-11/32 122174 5<br />
5 4-27/32 122175 5<br />
6-1/2 6-11/32 122176 5<br />
2 1-51/64 122177 5<br />
2-1/2 2-19/64 122178 5<br />
7/8 3 2-51/64 122179 5<br />
3-1/2 3-19/64 122180 5<br />
4 3-51/64 122181 5<br />
6 5-51/64 122182 5<br />
2 1-51/64 122183 5<br />
2-1/2 2-19/64 122184 5<br />
3 2-51/64 122185 5<br />
1 3/12 3-19/64 122186 5<br />
4 3-51/64 122187 5<br />
4-1/2 4-19/64 122188 5<br />
6 5-51/64 122189 5
Hairpin Cotters<br />
• Reusable.<br />
• Uni-Zinc plated to resist rust and corrosion.<br />
• Precision formed for better fit.<br />
Universal Clevis Pins<br />
• Precision formed for easy application.<br />
• Uni-zinc plated to resist rust and corrosion.<br />
• Can be cut off at any length.<br />
A quick replacement pin, this adjustable pin features a series of holes making it<br />
adaptable to varying lengths. Use the length desired and cut it off. Use to<br />
replace bolts, cotter pins, rivets, keys.<br />
PART # SIZE QTY.<br />
120847 1/4 x 2 25<br />
120848 5/16 x 2 25<br />
120849 3/8 x 2 25<br />
120850 7/16 x 2-1/2 20<br />
120851 1/2 x 2 10<br />
120852 1/2 x 2-1/2 10<br />
120853 5/8 x 3 10<br />
Cotter & Clevis Pin <strong>Fasteners</strong><br />
DECIMAL NOMINAL DIMENSIONS<br />
SHAFT SIZE PART # QTY. DIA. FRAC. DIA. A B D H L<br />
1/8 113920 10 .030 1/32 9/16 3/32 3/16 3/64 35<br />
3/16 113921 10 .0420 3/64 15/16 1/4 5/16 3/32 35<br />
1/4 113922 10 .0590 1/16 1-1/8 1/4 3/8 3/32 35<br />
5/16 113923 10 .0730 5/64 1-7/16 5/16 1/2 3/32 35<br />
3/8 113924 10 .0920 3/32 1-7/8 9/16 1-7/8 1/8 35<br />
1/2 113925 5 .1200 1/8 2-3/8 23/32 3/4 5/32 35<br />
5/8 113926 5 .1480 5/32 2-11/16 25/32 7/8 1/8 35<br />
1 113928 5 .1780 11/64 3-9/16 1-1/4 1-3/8 5/16 35<br />
1-1/4 113930 5 .2430 1/4 5 1-7/32 2 13/32 25<br />
1-1/2 113931 4 .3060 5/16 4 13/64 7/8 1/8 25<br />
Available in<br />
Assortments<br />
PART #00785<br />
Found on Page 72<br />
PART #00785KP<br />
Found on Page 73<br />
Available in<br />
an Assortment<br />
PART #00828<br />
Found on Page 73<br />
1 800 458-4018 www.uzengprod.com<br />
237<br />
FASTENERS
FASTENERS<br />
238<br />
Dowel Pin <strong>Fasteners</strong><br />
Dowel Pins<br />
• Hardened and ground.<br />
• Plain finish.<br />
DIA. LENGTH PART # QTY.<br />
3/16 122500 100<br />
1/4 122501 100<br />
3/8 122502 100<br />
1/16 1/2 122503 100<br />
5/8 122504 100<br />
3/4 122505 100<br />
7/8 122506 100<br />
1 122507 100<br />
3/16 122508 100<br />
1/4 122509 100<br />
3/8 122510 100<br />
1/2 122511 100<br />
3/32 5/8 122512 100<br />
3/4 122513 100<br />
7/8 122514 100<br />
1 122515 100<br />
3/8 122516 100<br />
1/2 122517 100<br />
5/8 122518 100<br />
3/4 122519 100<br />
1/8 7/8 122520 100<br />
1 122521 100<br />
1-1/2 122523 100<br />
1-3/4 122524 100<br />
2 122525 100<br />
1/2 122526 100<br />
5/8 122527 100<br />
3/4 122528 100<br />
7/8 122529 100<br />
3/16 1 122530 100<br />
1-1/4 122531 100<br />
1-1/2 122532 100<br />
1-3/4 122533 100<br />
2 122534 100<br />
1 800 458-4018 www.uzengprod.com<br />
DIA. LENGTH PART # QTY.<br />
1/2 122535 100<br />
5/8 122536 100<br />
3/4 122537 100<br />
7/8 122538 100<br />
1/4 1 122539 100<br />
1-1/4 122540 100<br />
1-1/2 122541 100<br />
1-3/4 122542 100<br />
2 122543 100<br />
2-1/4 122544 100<br />
2-1/2 122545 100<br />
1/2 122546 100<br />
5/8 122547 100<br />
3/4 122548 100<br />
7/8 122549 100<br />
1 122550 100<br />
5/16 1-1/4 122551 100<br />
1-1/2 122552 100<br />
1-3/4 122553 50<br />
2 122554 50<br />
2-1/4 122555 50<br />
2-1/2 122556 50<br />
3 122557 50<br />
1/2 122558 100<br />
5/8 122559 100<br />
3/4 122560 100<br />
7/8 122561 100<br />
1 122562 100<br />
3/8 1-1/4 122563 100<br />
1-1/2 122564 100<br />
1-3/4 122565 50<br />
2 122566 50<br />
2-1/4 122567 50<br />
2-1/2 122568 50<br />
3 122569 50<br />
1 122571 50<br />
1-1/4 122572 50<br />
1-1/2 122573 50<br />
7/16 1-3/4 122574 50<br />
2 122575 50<br />
2-1/2 122577 50<br />
3 122578 50<br />
DIA. LENGTH PART # QTY.<br />
3/4 122579 25<br />
1 122580 25<br />
1-1/4 122581 25<br />
1-1/2 122582 25<br />
1/2 1-3/4 122583 25<br />
2 122584 25<br />
2-1/4 122585 25<br />
2-1/2 122586 25<br />
3 122587 25<br />
3-1/2 122588 25<br />
4 122589 25<br />
1 122590 10<br />
1-1/4 122591 10<br />
1-1/2 122592 10<br />
1-3/4 122593 10<br />
2 122594 10<br />
5/8 2-1/4 122595 10<br />
2-1/2 122596 10<br />
3 122597 10<br />
3-1/2 122598 10<br />
4 122599 10<br />
4-1/2 122600 10<br />
5 122601 10<br />
2 122603 10<br />
2-1/2 122605 10<br />
3 122606 10<br />
3/4 3-1/2 122607 10<br />
4 122608 10<br />
4-1/2 122609 10<br />
5 122610 10<br />
6 122611 10
Taper Pins<br />
• Cold drawn low carbon steel , plain finish<br />
• Taper one-quarter inch per foot<br />
• Ideal for positioning components<br />
• Used to align holes in gears, sprockets and other machine parts<br />
• Meets ANSI/ASME B18.8.2<br />
NUMBER<br />
("D" DIA.)<br />
# 0<br />
(5/32)<br />
# 1<br />
(11/64)<br />
# 2<br />
(3/16)<br />
# 3<br />
(7/32)<br />
# 4<br />
(1/4)<br />
# 5<br />
(19/64)<br />
LGTH (L)<br />
3/4<br />
1<br />
1-1/2<br />
2<br />
3/4<br />
1<br />
1-1/2<br />
2<br />
3/4<br />
1<br />
1-1/2<br />
2<br />
3/4<br />
1<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
1<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
4<br />
1<br />
1-1/2<br />
SM END<br />
DIA. (S)<br />
.140<br />
.135<br />
.125<br />
.114<br />
.156<br />
.151<br />
.141<br />
.130<br />
.177<br />
.172<br />
.162<br />
.151<br />
.203<br />
.198<br />
.188<br />
.177<br />
.167<br />
.157<br />
.229<br />
.219<br />
.208<br />
.198<br />
.188<br />
.167<br />
.268<br />
.258<br />
* Please note these items are non-stock.<br />
“Highstress” Hitch Pins<br />
PART # DIA.<br />
USABLE<br />
LENGTH QTY.<br />
230200 5/8" 4-1/4" 1<br />
230201 5/8" 6-1/4" 1<br />
230202 3/4" 4-1/4" 1<br />
230203 3/4" 6-1/4" 1<br />
230204 7/8" 4-1/4" 1<br />
230205 7/8" 6-1/4" 1<br />
230206 1" 4-1/4" 1<br />
230207 1" 6-1/4" 1<br />
Lynch Pins - Plated<br />
PART # DIA. QTY.<br />
230247 3/16" 5<br />
230248 1/4" 5<br />
230249 5/16" 3<br />
230250 7/16" 1<br />
PART #<br />
122993*<br />
122994*<br />
122995*<br />
122996*<br />
122997*<br />
122998*<br />
122999*<br />
123000*<br />
123001*<br />
123002*<br />
123003*<br />
123004*<br />
123005*<br />
123006*<br />
123007*<br />
123008*<br />
123009*<br />
123010*<br />
123011*<br />
123012*<br />
123013*<br />
123014*<br />
123015*<br />
123016*<br />
123017*<br />
123018*<br />
Taper, Hitch & Lynch Pin <strong>Fasteners</strong><br />
PKG<br />
QTY<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
50<br />
25<br />
25<br />
50<br />
50<br />
25<br />
25<br />
25<br />
25<br />
50<br />
50<br />
25<br />
25<br />
25<br />
25<br />
50<br />
25<br />
NUMBER<br />
("D" DIA.)<br />
# 5<br />
(19/64)<br />
# 6<br />
(11/32)<br />
# 7<br />
(13/32)<br />
# 8<br />
(1/2)<br />
LGTH (L)<br />
2<br />
2-1/2<br />
3<br />
4<br />
5<br />
6<br />
1<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
4<br />
5<br />
6<br />
1<br />
1-1/2<br />
2<br />
2-1/2<br />
3<br />
4<br />
5<br />
6<br />
3<br />
4<br />
5<br />
6<br />
1. The large “man sized” handle (larger &<br />
easier to grasp than most) is not assembled<br />
into a drill-through hole. The handle is made<br />
from high carbon spring steel, is heat treated,<br />
and fits tightly into recessed blind holes;<br />
always a true fit!<br />
SM END<br />
DIA. (S)<br />
.247<br />
.237<br />
.227<br />
.206<br />
.185<br />
.164<br />
.320<br />
.310<br />
.299<br />
.289<br />
.279<br />
.258<br />
.237<br />
.216<br />
.388<br />
.378<br />
.367<br />
.357<br />
.347<br />
.326<br />
.305<br />
.284<br />
.430<br />
.409<br />
.388<br />
.367<br />
PART #<br />
123019*<br />
123020*<br />
123021*<br />
123022*<br />
123023*<br />
123024*<br />
123025*<br />
123026*<br />
123027*<br />
123028*<br />
123029*<br />
123030*<br />
123031*<br />
123032*<br />
123033*<br />
123034*<br />
123035*<br />
123036*<br />
123037*<br />
123038*<br />
123039*<br />
123040*<br />
123041*<br />
123042*<br />
123043*<br />
123044*<br />
1 800 458-4018 www.uzengprod.com<br />
PKG<br />
QTY<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
20<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
2. The collar may look as though it is just<br />
pressed down on top of the pin (like many<br />
competitive brands). On closer examination<br />
you will see the collar is cold forged into a<br />
groove in the body of the hitch pin. Certified<br />
test results show a force well in excess of<br />
10,000 lbs. is required to displace this collar<br />
from the hitch pin.<br />
3. The pin body is not just plain ordinary<br />
cold rolled steel, but “highstress” steel.<br />
Highstress is a high strength, heat treated &<br />
stress relieved alloy, certified to have a minimum<br />
yield strength of at least 100,000 PSI.<br />
239<br />
FASTENERS
FASTENERS<br />
240<br />
Snapper Pins<br />
SNAPPER PINS<br />
Snapper Pins - Double & Single Wire<br />
• Popular, quick connect and disconnect pins find many uses on machinery and shafts.<br />
• Two versions are available - round and square shaped.<br />
• Wire loop is pulled over the pin end to lock it in place or remove it.<br />
• Snapper pins eliminate cotter pin loss.<br />
• Made of low carbon steel cold-headed pin and spring wire loop, zinc plated<br />
PART #<br />
119022<br />
119023<br />
119024<br />
119025<br />
119026<br />
119027<br />
119028<br />
119029<br />
119030<br />
119031<br />
119032<br />
119033<br />
119034<br />
119035<br />
119036<br />
119037<br />
119038<br />
119039<br />
119040<br />
119041<br />
119042<br />
119043<br />
119044<br />
119045<br />
119046<br />
119047<br />
119048<br />
119049<br />
119050<br />
SIZE DIAMETER (D) X<br />
EFFECTIVE LGTH (EL)<br />
1/4 X 1-3/8<br />
1/4 X 1-3/4<br />
1/4 X 2-1/2<br />
5/16 X 1-3/8<br />
5/16 X 1-3/4<br />
5/16 X 2-1/4<br />
5/16 X 2-1/2<br />
3/8 X 1-3/8<br />
3/8 X 1-1/2<br />
3/8 X 1-3/4<br />
3/8 X 2-1/4<br />
3/8 X 2-1/2<br />
1/4 X 2-1/4<br />
1/4 X 2-1/2<br />
5/16 X 2-1/4<br />
5/16 X 2-1/2<br />
5/16 X 3<br />
3/8 X 2-1/4<br />
3/8 X 2-1/2<br />
3/8 X 3<br />
1/4 X 1-3/4<br />
5/16 X 1-3/4<br />
3/8 X 1-3/4<br />
1/4 X 2-1/2<br />
5/16 X 2-1/2<br />
5/16 X 3-1/2<br />
3/8 X 2-1/4<br />
3/8 X 2-1/2<br />
3/8 X 3<br />
1 800 458-4018 www.uzengprod.com<br />
HANDLE<br />
STYLE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
RD 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
SQ 2 WIRE<br />
RD 1 WIRE<br />
RD 1 WIRE<br />
RD 1 WIRE<br />
SQ 1 WIRE<br />
SQ 1 WIRE<br />
SQ 1 WIRE<br />
SQ 1 WIRE<br />
SQ 1 WIRE<br />
SQ 1 WIRE<br />
SHANK<br />
LGTH (SL)<br />
1-5/8<br />
2<br />
2-3/4<br />
1-5/8<br />
2<br />
2-1/2<br />
2-3/4<br />
1-5/8<br />
1-3/4<br />
2<br />
2-1/2<br />
2-3/4<br />
2-1/2<br />
2-3/4<br />
2-1/2<br />
2-3/4<br />
3-1/4<br />
2-1/2<br />
2-3/4<br />
3-1/4<br />
2<br />
2<br />
2<br />
2-3/4<br />
2-3/4<br />
3-3/4<br />
2-1/2<br />
2-3/4<br />
3-1/4<br />
WIRE DIA<br />
(T) +.002/-<br />
.002<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.091<br />
.118<br />
.118<br />
.118<br />
.118<br />
.118<br />
.118<br />
.118<br />
.118<br />
.118<br />
PART # 00431<br />
Found on Page 73<br />
WIRE<br />
CLEARANCE (W)<br />
+.125/-.125<br />
1.625<br />
1.625<br />
1.625<br />
1.75<br />
1.75<br />
1.75<br />
2.0<br />
1.50<br />
1.50<br />
1.50<br />
1.50<br />
1.50<br />
1.625<br />
1.625<br />
1.75<br />
2.0<br />
2.0<br />
1.50<br />
1.50<br />
1.50<br />
1.625<br />
1.75<br />
1.50<br />
1.625<br />
1.75<br />
1.75<br />
1.50<br />
1.50<br />
1.50<br />
PART # 00432<br />
Found on Page 74<br />
QTY<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
5<br />
10<br />
10<br />
5<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
10<br />
Available in<br />
Assortments<br />
PART # 00433<br />
Found on Page 74
Woodruff Keys<br />
PART THICKNESS LENGTH INDUSTRY<br />
# “A” “B” # QTY.<br />
03343 1/16 1/2 1 25<br />
03344 3/32 1/2 2 25<br />
03345 1/8 1/2 3 25<br />
03346 3/32 5/8 4 25<br />
03347 1/8 5/8 5 25<br />
03348 5/32 5/8 6 25<br />
03349 3/16 5/8 61 25<br />
03350 1/8 3/4 7 25<br />
03351 5/32 3/4 8 25<br />
03352 3/16 3/4 9 25<br />
03353 1/4 3/4 91 25<br />
03354 5/32 7/8 10 25<br />
03355 3/16 7/8 11 20<br />
03356 7/32 7/8 12 20<br />
03357 1/4 7/8 A 20<br />
03358 1/4 31/32 141 20<br />
03359 3/16 1 13 20<br />
03360 7/32 1 14 20<br />
Woodruff Key <strong>Fasteners</strong><br />
PART THICKNESS LENGTH INDUSTRY<br />
# “A” “B” # QTY.<br />
03361 1/4 1 15 20<br />
03362 5/16 1 B 20<br />
03363 3/8 1 152 15<br />
03364 3/16 1-1/8 16 15<br />
03365 7/32 1-1/8 17 15<br />
03366 1/4 1-1/8 18 15<br />
03367 5/16 1-1/8 C 15<br />
03368 3/16 1-1/4 19 15<br />
03369 7/32 1-1/4 20 15<br />
03370 1/4 1-1/4 21 15<br />
03371 5/16 1-1/4 D 15<br />
03372 3/8 1-1/4 E 10<br />
03373 1/4 1-3/8 22 10<br />
03374 5/16 1-3/8 23 10<br />
03375 3/8 1-3/8 F 10<br />
03376 1/4 1-1/2 24 10<br />
03377 5/16 1-1/2 25 10<br />
03378 3/8 1-1/2 G 10<br />
03379 03380 03383 03384<br />
03381 03382 03385 03386<br />
03387 03388 03389<br />
NOMINAL INDUSTRY<br />
PART # THICKNESS LENGTH # QTY.<br />
03379 3/16 2-1/8* 126 10<br />
03380 1/4 2-1/8* 127 10<br />
03381 5/16 2-1/8* 128 10<br />
03382 3/8 2-1/8* 129 10<br />
Note: *Nominal Length For Larger Sizes<br />
03383 3/16 2-1/8* 26 10<br />
03384 1/4 2-1/8* 27 10<br />
03385 5/16 2-1/8* 28 10<br />
03386 3/8 2-1/8* 29 10<br />
03387 1/4 2-3/4* RX 10<br />
03388 3/8 2-3/4* TX 10<br />
03389 1/2 2-3/4* VX 10<br />
1 800 458-4018 www.uzengprod.com<br />
241<br />
FASTENERS
FASTENERS<br />
242<br />
Woodruff Key <strong>Fasteners</strong><br />
Woodruff Keys<br />
• For repair work on vehicles, axles, shafts, trailers. • Use these scale drawings to identify exact size<br />
• Selected cold drawn 1035 steel, heat treated for strength. (length & thickness) and part number needed.<br />
• Precision machined for smooth finish and burr-free edges. • See next page for additional sizes, package quantities<br />
and specifications.<br />
3343 3344 3345 3346 3347 3348 3349<br />
3350 3351 3352 3353 3354 3355 3356<br />
3357 3358 3359 3360 3361 3362<br />
3363 3364 3365 3366 3367<br />
3368 3369 3370 3371 3372<br />
3373 3374 3375 3376 3377<br />
3378<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #00587<br />
Found on Page 74
Keystock<br />
Square Rectangular Undersized<br />
• Provides versatile cut and fit tolerances. • Made from C1018 steel.<br />
• Machined to exacting tolerances. • Uni-zinc plated to resist rust and corrosion.<br />
• Available in 12" and 36" lengths.<br />
Square<br />
12" Lengths<br />
Standard Tolerance<br />
+.002/-.000<br />
PART # SIZE QTY.<br />
03390 1/8 x 1/8 5<br />
03391 3/16 x 3/16 5<br />
03392 1/4 x 1/4 5<br />
03393 5/16 x 5/16 5<br />
03394 3/8 x 3/8 5<br />
03395 7/16 x 7/16 2<br />
03396 1/2 x 1/2 2<br />
03397 9/16 x 9/16 2<br />
03398 5/8 x 5/8 2<br />
03399 3/4 x 3/4 1<br />
03400 7/8 x 7/8 1<br />
03401 1 x 1 1<br />
122400 1-1/8 x 1-1/8 1<br />
122401 1-1/4 x 1-1/4 1<br />
122402 1-3/8 x 1-3/8 1<br />
122403 1-1/2 x 1-1/2 1<br />
Square<br />
36" Lengths<br />
Standard Tolerance<br />
+.002/-.000<br />
PART # SIZE QTY.<br />
122404 1/8 x 1/8 1<br />
122405 3/16 x 3/16 1<br />
122406 1/4 x 1/4 1<br />
122407 5/16 x 5/16 1<br />
122408 3/8 x 3/8 1<br />
122409 7/16 x 7/16 1<br />
122410 1/2 x 1/2 1<br />
122411 9/16 x 9/16 1<br />
122412 5/8 x 5/8 1<br />
122413 3/4 x 3/4 1<br />
122414 7/8 x 7/8 1<br />
122415 1 x 1 1<br />
Available in<br />
an Assortment<br />
PART # 00607<br />
Found on Page 74<br />
Rectangular<br />
12" Lengths<br />
Standard Tolerance<br />
+.002/-.000<br />
Keystock <strong>Fasteners</strong><br />
PART # SIZE QTY.<br />
122416 1/8 x 3/16 1<br />
122417 3/16 x 1/4 1<br />
122418 3/16 x 5/16 1<br />
122419 3/16 x 3/8 1<br />
122421 1/4 x 5/16 1<br />
122422 1/4 x 3/8 1<br />
122423 1/4 x 1/2 1<br />
122424 1/4 x 3/4 1<br />
122425 5/16 x 3/8 1<br />
122426 5/16 x 1/2 1<br />
122427 5/16 x 5/8 1<br />
122428 3/8 x 7/16 1<br />
122429 3/8 x 1/2 1<br />
122430 3/8 x 5/8 1<br />
122431 7/16 x 1/2 1<br />
122432 1/2 x 5/8 1<br />
122433 1/2 x 3/4 1<br />
122434 5/8 x 3/4 1<br />
122435 3/4 x 1 1<br />
122436<br />
Square<br />
12" Lengths<br />
1 x 1-1/4 1<br />
Undersized Tolerance<br />
+.000/-.002<br />
PART # SIZE QTY.<br />
121020 1/8 x 1/8 1<br />
121021 3/16 x 3/16 1<br />
121022 1/4 x 1/4 1<br />
121023 5/16 x 5/16 1<br />
121024 3/8 x 3/8 1<br />
121025 7/16 x 7/16 1<br />
121026 1/2 x 1/2 1<br />
121027 9/16 x 9/16 1<br />
121028 5/8 x 5/8 1<br />
121029 3/4 x 3/4 1<br />
121030 7/8 x 7/8 1<br />
121031 1 x 1 1<br />
1 800 458-4018 www.uzengprod.com<br />
243<br />
FASTENERS
FASTENERS<br />
244<br />
Spring Assortments<br />
Contains 42 - Compression Springs<br />
• Contains 42 sizes, one of each size, 42 total springs.<br />
• Outside diameter from 1/4" to 3/4".<br />
• Each spring is 11" long and has closed ends.<br />
• Packed in sturdy corrugated box.<br />
• General use applications.<br />
PART # 450293<br />
Contains 58 - Extension Springs<br />
• Contains 58 sizes, one of each size, 58 total springs.<br />
• Outside diameter from 1/4" to 3/4".<br />
• Each spring is 11" long and has plain ends.<br />
• Packed in sturdy corrugated box.<br />
• General use applications.<br />
PART # 450295<br />
Contains 126 - Small Compression<br />
Springs in 24 different sizes<br />
• Springs have outside diameters of 5/32, 3/16, 7/32, 1/4.<br />
• Packed in sturdy plastic box.<br />
• Ideal for repairing locks, electrical appliances, etc.<br />
PART # 450294<br />
Contains 126 - Small Extension Springs<br />
with looped Ends in 36 different sizes<br />
• Springs have outside diameters of 9/64, 5/32, 7/32, 1/4, 9/32, 5/16, 11/32.<br />
• Packed in sturdy plastic box.<br />
• Ideal for hardware stores, machine shops, or repair shops.<br />
PART # 450296<br />
1 800 458-4018 www.uzengprod.com
Metric Hex Head Cap Screws<br />
Class 10.9 (High Strength)<br />
Standard Thread<br />
• 150,800 PSI Tensile strength.<br />
• Equivalent to Grade 8.<br />
• Uni-zinc plate.<br />
DIN 931.10 PARTIALLY THREADED (PT)<br />
M6 DIAMETER<br />
Thread pitch - 1.0 MM<br />
Width across flats - 10 MM<br />
Head height - 4 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
12 151200 FT 50<br />
14 151201 FT 50<br />
16 151202 FT 50<br />
20 151203 FT 50<br />
25 151204 FT 50<br />
30 151205 PT 50<br />
35 151206 PT 50<br />
40 151207 PT 50<br />
45 151208 PT 50<br />
50 151209 PT 25<br />
60 151210 PT 25<br />
M10 DIAMETER<br />
Thread pitch - 1.5 MM<br />
Width across flats - 17 MM<br />
Head height - 6.4 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
16 04610 FT 50<br />
20 04611 FT 50<br />
25 04612 FT 25<br />
30 04613 FT 25<br />
35 04614 FT 25<br />
40 04615 PT 25<br />
45 04616 PT 25<br />
50 04617 PT 25<br />
55 04618 PT 25<br />
60 04619 PT 25<br />
65 04620 PT 10<br />
70 04621 PT 10<br />
75 04622 PT 10<br />
80 04623 PT 10<br />
90 04624 PT 10<br />
100 04625 PT 10<br />
DIN 933.10 FULLY THREADED (FT)<br />
M8 DIAMETER<br />
Thread pitch - 1.25 MM<br />
Width across flats - 13 MM<br />
Head height - 5.3 MM<br />
Metric <strong>Fasteners</strong><br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
16 04600 FT 50<br />
20 04601 FT 50<br />
25 04602 FT 50<br />
30 04603 FT 50<br />
35 04604 FT 50<br />
40 04605 PT 50<br />
45 04606 PT 50<br />
50 04607 PT 50<br />
55 151219 PT 50<br />
60 04608 PT 25<br />
70 04609 PT 25<br />
80 04686 PT 25<br />
M12 DIAMETER<br />
Thread pitch - 1.75 MM<br />
Width across flats - 19 MM<br />
Head height - 5.3 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 04626 FT 25<br />
25 04627 FT 25<br />
30 04628 FT 25<br />
35 04629 FT 25<br />
40 04630 FT 25<br />
45 04631 PT 25<br />
50 04632 PT 25<br />
55 04633 PT 25<br />
60 04634 PT 20<br />
65 04635 PT 10<br />
70 04636 PT 10<br />
75 151246 PT 10<br />
80 04637 PT 10<br />
90 04638 PT 10<br />
100 04639 PT 10<br />
110 04693 PT 10<br />
120 04640 PT 10<br />
1 800 458-4018 www.uzengprod.com<br />
245<br />
FASTENERS
FASTENERS<br />
246<br />
Metric <strong>Fasteners</strong><br />
Metric Hex Head Cap Screws<br />
Class 10.9 (High Strength)<br />
Standard Thread<br />
• 150,800 PSI Tensile Strength.<br />
• Equivalent to Grade 8.<br />
• Uni-zinc plate.<br />
DIN 933.10 FULLY THREADED (FT)<br />
M14 DIAMETER<br />
Thread pitch - 2.0 MM<br />
Width across flats - 22 MM<br />
Head height - 8.8 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
30 04694 FT 10<br />
35 04695 FT 10<br />
40 04696 FT 10<br />
45 04697 FT 10<br />
50 04698 PT 5<br />
55 04699 PT 5<br />
60 04700 PT 5<br />
70 151257 PT 5<br />
80 151258 PT 5<br />
90 151259 PT 5<br />
100 151260 PT 5<br />
M20 DIAMETER<br />
Thread pitch - 2.5 MM<br />
Width across flats - 30 MM<br />
Head height - 12.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
40 04654 FT 5<br />
45 151277 FT 5<br />
50 04655 FT 5<br />
60 04656 FT 5<br />
70 04657 FT 5<br />
80 04658 PT 5<br />
90 151284 PT 5<br />
100 04659 PT 5<br />
110 151286 PT 5<br />
120 04660 PT 5<br />
140 04661 PT 5<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #105301<br />
Found on Page 75<br />
PART #105302<br />
Found on Page 75<br />
DIN 931.10 PARTIALLY THREADED (PT)<br />
M16 DIAMETER<br />
Thread pitch - 2.0 MM<br />
Width across flats - 24 MM<br />
Head height -10 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
30 04641 FT 10<br />
35 151262 FT 10<br />
40 04642 FT 10<br />
45 151264 FT 10<br />
50 04643 FT 10<br />
55 151266 PT 10<br />
60 04644 PT 10<br />
65 151268 PT 10<br />
70 04645 PT 10<br />
75 04646 PT 10<br />
80 04647 PT 5<br />
90 04648 PT 5<br />
100 04649 PT 5<br />
110 04650 PT 5<br />
120 04651 PT 5<br />
130 04652 PT 5<br />
140 04653 PT 5<br />
M24 DIAMETER<br />
Thread pitch - 3.0 MM<br />
Width across flats - 36 MM<br />
Head height - 15 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
50 04662 FT 5<br />
60 04663 FT 5<br />
70 04664 FT 5<br />
80 04665 PT 5<br />
100 04666 PT 5<br />
120 04667 PT 5
Hi-Strength Metric <strong>Fasteners</strong><br />
FOR USE WITH CLASS 10.9 CAP SCREWS<br />
Hexagon Nuts<br />
• DIN 934-10.<br />
• Class 10.<br />
• ISO 4032.<br />
• ANSI B 18.2.4.1M.<br />
• Uni-zinc plated.<br />
“D” WIDTH<br />
PART # SIZE ACROSS THICKNESS QTY.<br />
MM FLATS MM MM<br />
151300 6 x 1.0 10 5 100<br />
04668 8 x 1.25 13 6.5 100<br />
04669 10 x 1.50 17 8 50<br />
04670 12 x 1.75 19 10 25<br />
04701 14 x 2.0 22 11 25<br />
04671 16 x 2.0 24 13 25<br />
04672 20 x 2.5 30 16 10<br />
04673 24 x 3.0 36 19 10<br />
Special Metric Flat Washers<br />
• DIN 125A.<br />
• ISO 7089/7090.<br />
• Hardness - 200 Brinell (94 HRB)<br />
MIN. 102,950 PSI.<br />
• Uni-zinc plated.<br />
PART #<br />
BOLT<br />
SIZE I.D. O.D. THICKNESS QTY.<br />
MM MM MM MM<br />
151310 6 6.4 12 1.6 100<br />
04674 8 8.4 16 1.6 100<br />
04675 10 10.5 20 2 100<br />
04676 12 13 24 2.5 75<br />
04702 14 15 28 2.5 50<br />
04677 16 17 30 3 50<br />
04678 20 21 37 3 25<br />
04679 24 25 44 4 10<br />
Hex Flange Nuts - Metric<br />
PART # SIZE QTY.<br />
152310 6 x 1.0 25<br />
152311 8 x 1.25 25<br />
152312 10 x 1.50 25<br />
152313 12 x 1.75 25<br />
D<br />
H<br />
120°<br />
F<br />
Metric <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
247<br />
FASTENERS
FASTENERS<br />
248<br />
Metric <strong>Fasteners</strong><br />
Metric Hex Head Cap Screws<br />
Class 8.8<br />
Standard Thread<br />
• 116,000 PSI Tensile strength.<br />
• Equivalent to Grade 5.<br />
• Uni-zinc plate.<br />
DIN 931 PARTIALLY THREADED (PT)<br />
M3 DIAMETER<br />
Thread pitch - 0.5MM<br />
Width across flats - 5.5 MM<br />
Head height - 2 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
6 150080 FT 50<br />
8 150081 FT 50<br />
10 150082 FT 50<br />
12 150083 FT 50<br />
16 150085 FT 50<br />
18 150086 FT 50<br />
20 150087 FT 25<br />
25 150088 FT 25<br />
30 150089 FT 25<br />
M5 DIAMETER<br />
Thread pitch - 0.8 MM<br />
Width across flats - 8 MM<br />
Head height - 3.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
8 150117 FT 50<br />
10 04512 FT 50<br />
12 04513 FT 50<br />
16 04514 FT 50<br />
18 150121 FT 50<br />
20 04515 FT 50<br />
25 04516 FT 50<br />
30 04517 FT 50<br />
35 04518 FT 25<br />
40 04519 FT 25<br />
45 04520 PT 25<br />
50 04521 PT 25<br />
55 150131 PT 25<br />
60 04522 PT 10<br />
65 150133 PT 10<br />
70 04523 PT 10<br />
80 150136 PT 10<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 105298<br />
Found on Page 76<br />
PART # 105299<br />
Found on Page 76<br />
PART # 105300<br />
Found on Page 77<br />
PART # 00508<br />
Found on Page 78<br />
DIN 933 FULLY THREADED (FT)<br />
M4 DIAMETER<br />
Thread pitch - 0.7 MM<br />
Width across flats - 7 MM<br />
Head height - 2.8 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
6 04500 FT 50<br />
8 150100 FT 50<br />
10 04501 FT 50<br />
12 04502 FT 50<br />
16 04503 FT 50<br />
18 150104 FT 50<br />
20 04504 FT 50<br />
25 04505 FT 50<br />
30 04506 FT 50<br />
35 04507 PT 50<br />
40 04508 PT 10<br />
45 04509 PT 10<br />
50 04510 PT 10<br />
M6 DIAMETER<br />
Thread pitch - 1 MM<br />
Width across flats - 10 MM<br />
Head height - 4 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
6 04524 FT 50<br />
8 150138 FT 50<br />
10 04525 FT 50<br />
12 04526 FT 50<br />
16 04527 FT 50<br />
18 150142 FT 50<br />
20 04528 FT 50<br />
25 04529 FT 50<br />
30 04530 PT 50<br />
35 04531 PT 50<br />
40 04532 PT 50<br />
45 04533 PT 25<br />
50 04534 PT 25<br />
55 150152 PT 25<br />
60 04535 PT 25<br />
65 150154 PT 25<br />
70 04536 PT 10<br />
75 04537 PT 10<br />
80 04538 PT 10<br />
90 150158 PT 10<br />
100 150159 PT 10
Metric Hex Head Cap Screws<br />
Class 8.8<br />
Standard Thread<br />
M7 DIAMETER<br />
Thread pitch - 1 MM<br />
Width across flats - 11 MM<br />
Head height - 5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
10 150166 FT 25<br />
12 150167 FT 25<br />
16 04539 FT 25<br />
20 04540 FT 25<br />
25 04541 FT 25<br />
30 04542 FT 25<br />
35 04543 FT 25<br />
40 04544 FT 25<br />
45 04545 FT 25<br />
M10 DIAMETER<br />
Thread pitch - 1.5MM<br />
Width across flats - 16 MM<br />
Head height - 6.4 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
12 150210 FT 25<br />
16 150211 FT 25<br />
20 150213 FT 25<br />
25 150215 FT 25<br />
30 150217 FT 25<br />
35 150218 FT 25<br />
40 150219 FT 10<br />
45 150220 FT 10<br />
50 150221 FT 10<br />
55 150222 PT 10<br />
60 150223 PT 10<br />
65 150224 PT 10<br />
70 150225 PT 10<br />
75 150226 PT 10<br />
80 150227 PT 10<br />
90 150229 PT 10<br />
100 150230 PT 10<br />
110 150231 PT 10<br />
120 150232 PT 10<br />
130 150233 PT 10<br />
140 150234 PT 10<br />
150 150235 PT 10<br />
M8 DIAMETER<br />
Thread pitch - 1.25MM<br />
Width across flats - 13 MM<br />
Head height - 5.3 MM<br />
Metric <strong>Fasteners</strong><br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
10 150181 FT 50<br />
12 150182 FT 50<br />
16 150184 FT 50<br />
20 150185 FT 50<br />
25 150187 FT 50<br />
30 150189 FT 25<br />
35 150190 FT 25<br />
40 150191 FT 25<br />
45 150192 PT 25<br />
50 150193 PT 25<br />
55 150194 PT 25<br />
60 150195 PT 25<br />
65 150196 PT 25<br />
70 150197 PT 25<br />
75 150198 PT 25<br />
80 150199 PT 25<br />
90 150201 PT 10<br />
100 150202 PT 10<br />
110 150203 PT 10<br />
120 150204 PT 10<br />
M12 DIAMETER<br />
Thread pitch - 1.75 MM<br />
Width across flats - 19 MM<br />
Head height - 7.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
16 150241 FT 25<br />
20 150242 FT 25<br />
25 150244 FT 25<br />
30 150245 FT 25<br />
35 150246 FT 25<br />
40 150247 FT 10<br />
45 150248 FT 10<br />
50 150249 FT 10<br />
55 150250 FT 10<br />
60 150251 FT 10<br />
65 150252 PT 10<br />
70 150253 PT 10<br />
75 150254 PT 10<br />
80 150255 PT 10<br />
85 150256 PT 10<br />
90 150257 PT 10<br />
100 150258 PT 10<br />
110 150259 PT 10<br />
120 150260 PT 10<br />
130 150261 PT 10<br />
140 150262 PT 10<br />
150 150263 PT 10<br />
160 150264 PT 10<br />
180 150265 PT 10<br />
1 800 458-4018 www.uzengprod.com<br />
249<br />
FASTENERS
FASTENERS<br />
250<br />
Metric <strong>Fasteners</strong><br />
Metric Hex Head Cap Screws<br />
Class 8.8<br />
Standard Thread<br />
M14 DIAMETER<br />
Thread pitch - 2 MM<br />
Width across flats - 22 MM<br />
Head height - 8.8 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 151000 FT 10<br />
25 151001 FT 10<br />
30 151002 FT 10<br />
35 151003 FT 10<br />
40 151004 FT 10<br />
45 151005 FT 10<br />
50 151006 FT 10<br />
55 151007 PT 10<br />
60 151008 PT 10<br />
65 151009 PT 10<br />
70 151010 PT 10<br />
80 151012 PT 10<br />
90 151013 PT 10<br />
100 151014 PT 10<br />
M18 DIAMETER<br />
Thread pitch - 2.5MM<br />
Width across flats - 27 MM<br />
Head height - 11.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
40 151042 FT 10<br />
45 151043 FT 10<br />
50 151044 FT 10<br />
55 151045 FT 10<br />
60 151046 FT 10<br />
70 151048 PT 10<br />
80 151050 PT 10<br />
90 151051 PT 10<br />
100 151052 PT 10<br />
1 800 458-4018 www.uzengprod.com<br />
M16 DIAMETER<br />
Thread pitch - 2 MM<br />
Width across flats - 24 MM<br />
Head height - 10 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 151020 FT 10<br />
25 151021 FT 10<br />
30 151022 FT 10<br />
35 151023 FT 10<br />
40 151024 FT 10<br />
45 151025 FT 10<br />
50 151026 FT 10<br />
55 151027 FT 10<br />
60 151028 FT 10<br />
65 151029 PT 10<br />
70 151030 PT 10<br />
75 151031 PT 10<br />
80 151032 PT 10<br />
90 151033 PT 10<br />
100 151034 PT 10<br />
M20 DIAMETER<br />
Thread pitch - 2.5 MM<br />
Width across flats - 30 MM<br />
Head height - 12.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
30 151060 FT 10<br />
35 151061 FT 10<br />
40 151062 FT 10<br />
45 151063 FT 10<br />
50 151064 FT 10<br />
55 151065 FT 10<br />
60 151066 FT 10<br />
65 151067 PT 10<br />
70 151068 PT 10<br />
75 151069 PT 10<br />
80 151070 PT 10<br />
90 151071 PT 10<br />
100 151072 PT 10
Metric Hex Head Cap Screws<br />
Class 8.8 Fine Thread<br />
DIN 961 FULLY THREADED (FT)<br />
DIN 960 PARTIALLY THREADED (PT)<br />
M8 DIAMETER<br />
Thread pitch - 1.0 MM<br />
Width across flats - 13 MM<br />
Head height - 5.3 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
10 04750 FT 50<br />
16 04751 FT 50<br />
20 04752 FT 50<br />
25 04753 FT 50<br />
30 04754 FT 25<br />
35 04755 FT 25<br />
40 04756 FT 25<br />
45 04757 FT 25<br />
50 04758 FT 25<br />
55 151108 PT 25<br />
60 151109 PT 25<br />
70 151110 PT 25<br />
80 151111 PT 25<br />
M10 DIAMETER<br />
Thread pitch - 1.0 MM<br />
Width across flats - 17 MM<br />
Head height - 7 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 151113 FT 25<br />
25 151114 FT 25<br />
30 151115 FT 25<br />
35 151116 FT 25<br />
40 151117 FT 25<br />
45 151118 FT 25<br />
50 151119 FT 25<br />
55 151120 PT 25<br />
60 151121 PT 10<br />
70 151122 PT 10<br />
80 151123 PT 10<br />
M10 DIAMETER<br />
Thread pitch - 1.25 MM<br />
Width across flats - 16 MM<br />
Head height - 7 MM<br />
Metric <strong>Fasteners</strong><br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 04760 FT 25<br />
25 04761 FT 25<br />
30 04762 FT 25<br />
35 04763 FT 25<br />
40 04764 FT 10<br />
45 04765 PT 10<br />
50 04766 PT 10<br />
55 04767 PT 10<br />
60 04768 PT 10<br />
70 151135 PT 10<br />
80 151136 PT 10<br />
100 151137 PT 10<br />
M12 DIAMETER<br />
Thread pitch - 1.25 MM<br />
Width across flats - 18 MM<br />
Head height - 7.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 151138 FT 25<br />
25 151139 FT 25<br />
30 151140 FT 25<br />
35 151141 FT 25<br />
40 151142 FT 10<br />
45 151143 PT 10<br />
50 151144 PT 10<br />
55 151145 PT 10<br />
60 151146 PT 10<br />
70 151147 PT 10<br />
80 151148 PT 10<br />
100 151150 PT 10<br />
120 151151 PT 10<br />
M12 DIAMETER<br />
Thread pitch - 1.50 MM<br />
Width across flats - 18 MM<br />
Head height - 7.5 MM<br />
LENGTH THREAD<br />
MM PART # LENGTH QTY.<br />
20 151152 FT 25<br />
25 04770 FT 25<br />
30 04771 FT 25<br />
35 04772 FT 25<br />
40 04773 FT 10<br />
45 04774 FT 10<br />
50 04775 FT 10<br />
55 04776 PT 10<br />
60 04777 PT 10<br />
70 151161 PT 10<br />
80 151162 PT 10<br />
90 151163 PT 10<br />
1 800 458-4018 www.uzengprod.com<br />
251<br />
FASTENERS
FASTENERS<br />
252<br />
Metric <strong>Fasteners</strong><br />
Metric <strong>Fasteners</strong><br />
For use with Class 8.8 Cap Screws<br />
Hexagon Nuts<br />
• DIN 934.<br />
• ISO 4032.<br />
• ANSI B 18.2.4.1M.<br />
• Uni- zinc plated.<br />
(F)-Fine Thread<br />
Lockwashers<br />
• DIN 127B.<br />
• Spring steel.<br />
• Uni-zinc plated.<br />
• For use with all metric cap screws.<br />
Hex Jam Nuts<br />
• DIN 439B.<br />
• ISO 4035.<br />
• ANSI B 18.2.4.5M.<br />
• Uni-zinc plated.<br />
1 800 458-4018 www.uzengprod.com<br />
WIDTH<br />
PART # SIZE ACROSS THICKNESS QTY.<br />
MM FLATS MM MM<br />
150269 2 x .40 4.0 1.6 100<br />
150772 3 x .050 5.5 2.4 100<br />
04547 4 x .070 7 3.2 100<br />
04548 5 x 0.80 8 4.0 100<br />
04549 6 x 1.00 10 5.0 100<br />
04550 7 x 1.00 11 5.5 100<br />
150275 8 x 1.25 13 6.5 100<br />
04795 8(F) x 1.00 13 6.5 75<br />
150276 10 x 1.50 17 8.0 50<br />
150802 10(F) x 1.00 17 8.0 50<br />
04796 10(F) x 1.25 17 8.0 25<br />
150277 12 x 1.75 19 10.0 25<br />
150804 12(F) x 1.25 19 10.0 25<br />
04797 12(F) x 1.50 19 10.0 25<br />
150806 14 x 2.00 22 11.0 25<br />
150807 14(F) x 1.50 22 11.0 25<br />
150808 16 x 2.00 24 13.0 25<br />
150809 16(F) x 1.50 24 13.0 10<br />
150810 18 x 2.50 27 15.0 10<br />
150811 18(F) x 1.50 27 15.0 10<br />
150812 20 x 2.50 30 16.0 10<br />
150813 20(F) x 1.50 30 16.0 10<br />
BOLT<br />
PART # SIZE I.D. O.D. THICKNESS QTY.<br />
MM MM MM MM<br />
150280 2 2.1 4.4 0.5 100<br />
150774 3 3.1 6.2 0.8 100<br />
04555 4 4.1 7.6 0.9 100<br />
04556 5 5.1 9.2 1.2 100<br />
04557 6 6.1 11.8 1.6 100<br />
04558 7 7.1 12.8 1.6 100<br />
04680 8 8.1 14.2 2.0 100<br />
04681 10 10.2 18.1 2.2 100<br />
04682 12 12.2 21.1 2.5 100<br />
04703 14 14.2 24.1 3.0 100<br />
04683 16 16.2 27.4 3.5 100<br />
150291 18 18.2 29.4 3.5 25<br />
04684 20 20.2 33.6 4.0 20<br />
04685 24 24.5 40.0 5.0 20<br />
WIDTH<br />
PART # SIZE ACROSS THICKNESS QTY.<br />
MM FLATS MM MM<br />
150890 3 x 0.5 1.8 5.5 100<br />
150891 4 x 0.7 2.2 7.0 100<br />
150892 5 x 0.8 2.7 8.0 100<br />
150893 6 x 1.0 3.2 10.0 100<br />
150895 8 x 1.25 4.0 13.0 100<br />
150896 10 x 1.5 5.0 17.0 50<br />
150897 12 x 1.75 6.0 19.0 25<br />
150898 14 x 2.0 7.0 22.0 25<br />
150899 16 x 2.5 8.0 24.0 25<br />
150901 20 x 2.5 10.0 30.0 25
Metric <strong>Fasteners</strong><br />
For use with Class 8.8 Cap Screws<br />
Flat Washers<br />
• DIN 125<br />
• Uni-zinc plated.<br />
BOLT “A” “B” “C”<br />
SIZE I.D. O.D. THICKNESS<br />
PART # MM MM MM MM QTY.<br />
150830 2 2.2 5 0.3 100<br />
150773 3 3.2 7 0.5 100<br />
04551 4 4.3 9 0.8 100<br />
04552 5 5.3 11 1.0 100<br />
04553 6 6.4 12 1.6 100<br />
04554 7 7.4 14 1.6 100<br />
150297 8 8.4 16 1.6 100<br />
150298 10 10.5 20 2.0 100<br />
150299 12 13.0 24 2.5 75<br />
150831 14 15.0 28 2.5 50<br />
150832 16 17.0 30 3.0 50<br />
150833 18 19.0 34 3.0 25<br />
150834 20 21.0 37 3.0 25<br />
Nylon Insert Lock Nuts<br />
• DIN 985.<br />
• ISO 7040.<br />
• ANSI B 18.16.3M.<br />
• Uni-zinc plated.<br />
SIZE<br />
WIDTH<br />
ACROSS THICKNESS<br />
PART # MM FLATS MM MM QTY.<br />
150850 3 x 0.5 5.5 4.0 100<br />
150851 4 x 0.7 7.0 5.0 100<br />
150852 5 x 0.8 8.0 5.0 100<br />
150853 6 x 1.0 10.0 6.0 50<br />
150855 8 x 1.25 13.0 8.0 50<br />
150856 8(F) x 1.0 13.0 8.0 50<br />
150857 10 x 1.5 17.0 10.0 25<br />
150858 10(F) x 1.25 17.0 10.0 10<br />
150859 10(F) x 1.0 17.0 10.0 10<br />
150860 12 x 1.75 19.0 12.0 10<br />
150861 12(F) x 1.5 19.0 12.0 10<br />
150862 12(F) x 1.25 19.0 12.0 10<br />
150863 14 x 2.0 22.0 14.0 10<br />
150864 16 x 2.0 24.0 16.0 10<br />
150865 18 x 2.5 27.0 18.5 10<br />
150866 20 x 2.5 30.0 20.0 10<br />
Wing Nuts<br />
• DIN 315.<br />
• Uni-zinc plated.<br />
Metric <strong>Fasteners</strong><br />
SIZE HEIGHT<br />
PART # MM MM QTY.<br />
150870 3 x 0.5 10 25<br />
150871 4 x 0.7 10.5 25<br />
150872 5 x 0.8 13 25<br />
150873 6 x 1.0 17 25<br />
150874 8 x 1.25 20 25<br />
150875 10 x 1.5 25 20<br />
150876 12 x 1.75 33.5 10<br />
150878 16 x 2.0 37.5 5<br />
Class 8 All-Metal Prevailing<br />
Torque Locknuts<br />
• Din 980V<br />
• Top of nut is compressed to form an oval-shaped locking zone. Twist<br />
freely on bolt until it makes contact with the locking zone. They then<br />
expand to an almost circular shape, creating a locking compression.<br />
• Used for medium strength applications.<br />
• Zinc plated<br />
WIDTH<br />
SIZE ACROSS THICKNESS<br />
PART # MM FLATS MM MM QTY.<br />
152341 4 X 0.7 7 4.2 25<br />
152342 5 X 0.8 8 5.1 25<br />
152343 6 X 1.0 10 6 25<br />
152344 8 X 1.25 13 8 25<br />
120195 8(F) X 1.0 13 8 25<br />
152345 10 X 1.50 17 10 25<br />
120196 10(F) X 1.25 17 10 25<br />
152346 12 X 1.75 19 12 25<br />
120197 12(F) X 1.50 19 12 25<br />
120198 12(F) X 1.25 19 12 25<br />
120199 14 X 2.0 22 14 10<br />
120200 14(F) X 1.50 22 14 10<br />
120201 16 X 2.0 24 16 10<br />
120202 16(F) X 1.50 24 16 10<br />
120203 18 X 2.50 27 18 10<br />
120204 18(F) X 1.50 27 18 10<br />
120205 20 X 2.50 30 20 10<br />
120206 20(F) X 1.50 30 20 10<br />
1 800 458-4018 www.uzengprod.com<br />
253<br />
FASTENERS
FASTENERS<br />
254<br />
Metric <strong>Fasteners</strong><br />
Metric Toothed Lockwashers<br />
Internal Toothed Lock Washers<br />
• DIN 6797 I.<br />
• Spring steel.<br />
• Uni-zinc plated.<br />
BOLT<br />
SIZE I.D. O.D.<br />
PART # MM MM MM QTY.<br />
150910 2 2.2 4.5 100<br />
150911 3 3.2 6.0 100<br />
150912 4 4.3 8.0 100<br />
150913 5 5.3 10.0 100<br />
150914 6 6.4 11.0 100<br />
150915 8 8.4 15.0 100<br />
150916 10 10.5 18.0 50<br />
150917 12 12.5 20.5 50<br />
150918 14 14.5 24.0 50<br />
150919 16 16.5 26.0 25<br />
150920 18 19.0 30.0 25<br />
150921 20 21.0 33.0 25<br />
Spring Washers<br />
• DIN 137.<br />
• Spring steel.<br />
• Uni-zinc plated.<br />
BOLT<br />
SIZE I.D. O.D. THICKNESS<br />
PART # MM MM MM MM QTY.<br />
150775 3 3.2 8 0.5 100<br />
04710 4 4.3 9 0.5 100<br />
04711 5 5.3 11 0.5 100<br />
04712 6 6.4 12 0.5 100<br />
04714 8 8.4 15 0.8 100<br />
04715 10 10.5 21 1.0 75<br />
04716 12 13.0 24 1.2 50<br />
04717 14 15.0 28 1.6 50<br />
04718 16 17.0 30 1.6 25<br />
150842 18 19.0 34 1.6 20<br />
04719 20 21.0 36 1.6 20<br />
1 800 458-4018 www.uzengprod.com<br />
External Toothed Lock Washers<br />
• DIN 6797 A.<br />
• Spring steel.<br />
• Uni-zinc plated.<br />
BOLT<br />
SIZE I.D. O.D.<br />
PART # MM MM MM QTY.<br />
150925 2 2.2 4.5 100<br />
150926 3 3.2 6.0 100<br />
150927 4 4.3 8.0 100<br />
150928 5 5.3 10.0 100<br />
150929 6 6.4 11.0 100<br />
150930 8 8.4 15.0 100<br />
150931 10 10.5 18.0 50<br />
150932 12 12.5 20.5 50<br />
150933 14 14.5 24.0 25<br />
150934 16 16.5 26.0 25<br />
150935 18 19.0 30.0 25<br />
150936 20 21.0 33.0 25<br />
Available in<br />
an Assortment<br />
PART # 00766<br />
Found on Page 78<br />
PART # 00766KP<br />
Found on Page 79
Metric Hex Socket Cap Screws<br />
• Class 12.9 (176,900 PSI).<br />
• DIN 912-12.9.<br />
• ISO 4762.<br />
• ANSI B 18.31M.<br />
• Black satin finish.<br />
• Heat treated alloy steel.<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
5 152000 100<br />
6 152001 25<br />
8 152002 25<br />
10 152003 25<br />
M3 12 152004 25<br />
0.5 Pitch 14 152005 25<br />
2.5 Key 16 152006 25<br />
20 152008 25<br />
25 152009 25<br />
30 152010 25<br />
35 152011 25<br />
6 150320 25<br />
8 150321 25<br />
10 150322 25<br />
12 150323 25<br />
M4 16 150325 25<br />
0.7 Pitch 20 150327 25<br />
3.0 Key 25 150329 25<br />
30 150330 25<br />
35 150331 25<br />
40 150332 25<br />
45 150333 25<br />
50 150334 25<br />
8 150337 25<br />
10 150338 25<br />
12 150339 25<br />
16 150341 25<br />
20 150343 25<br />
M5 25 150345 25<br />
0.8 Pitch 30 150346 25<br />
4.0 Key 35 150347 25<br />
40 150348 25<br />
45 150349 25<br />
50 150350 25<br />
55 150351 25<br />
60 150352 25<br />
70 150354 25<br />
Metric <strong>Fasteners</strong><br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
8 150358 25<br />
10 04830 25<br />
12 150360 25<br />
16 04831 25<br />
20 04832 25<br />
25 04833 25<br />
30 04834 25<br />
35 04835 25<br />
40 04836 25<br />
M6 45 04837 25<br />
1.0 Pitch 50 04838 25<br />
5.0 Key 55 04839 25<br />
60 04840 25<br />
65 150374 25<br />
70 150375 25<br />
75 150376 25<br />
80 150377 25<br />
90 150378 25<br />
100 150379 25<br />
110 150380 25<br />
120 150381 25<br />
10 150382 25<br />
12 150383 25<br />
14 150384 25<br />
16 04841 25<br />
20 04842 25<br />
25 04843 25<br />
30 04844 25<br />
35 04845 25<br />
40 04846 25<br />
45 04847 25<br />
50 04848 25<br />
M8 55 04849 25<br />
1.25 Pitch 60 04850 25<br />
6.0 Key 65 150397 25<br />
70 150398 25<br />
75 150399 25<br />
80 150400 25<br />
90 150401 25<br />
100 150402 25<br />
110 150403 25<br />
120 150404 25<br />
130 150405 25<br />
140 150406 25<br />
150 150407 25<br />
160 150408 25<br />
180 150409 25<br />
200 150410 25<br />
1 800 458-4018 www.uzengprod.com<br />
255<br />
FASTENERS
FASTENERS<br />
256<br />
Metric <strong>Fasteners</strong><br />
Metric Hex Socket Cap Screws<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
12 150412 25<br />
16 04851 25<br />
20 04852 25<br />
25 04853 25<br />
30 04854 25<br />
35 04855 25<br />
40 04856 25<br />
45 04857 25<br />
50 04858 25<br />
55 04859 25<br />
M10 60 04860 25<br />
1.50 Pitch 65 150425 25<br />
8.0 Key 70 150426 25<br />
75 150427 25<br />
80 150428 25<br />
90 150429 25<br />
100 150430 25<br />
110 150431 25<br />
120 150432 25<br />
130 150433 25<br />
140 150434 25<br />
150 150435 25<br />
160 150436 25<br />
180 150437 25<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
30 150465 25<br />
35 150466 25<br />
40 150467 25<br />
45 150468 25<br />
50 150469 25<br />
55 150470 25<br />
M14 60 150471 25<br />
2.0 Pitch 65 150472 25<br />
12 Key 70 150473 25<br />
75 150474 25<br />
80 150475 25<br />
90 150476 25<br />
100 150477 25<br />
110 150478 25<br />
120 150479 25<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
20 04861 25<br />
25 04862 25<br />
30 04863 25<br />
35 04864 25<br />
40 04865 25<br />
45 04866 25<br />
50 04867 25<br />
55 04868 25<br />
60 04869 25<br />
M12 65 04870 25<br />
1.75 Pitch 70 04871 25<br />
10 Key 75 150453 25<br />
80 150454 25<br />
90 150455 25<br />
100 150456 25<br />
110 150457 25<br />
120 150458 25<br />
130 150459 25<br />
140 150460 25<br />
150 150461 25<br />
160 150462 25<br />
180 150463 25<br />
200 150464 25
Metric Hex Socket Cap Screws<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
30 150480 25<br />
35 150481 25<br />
40 150482 25<br />
45 150483 25<br />
50 150484 25<br />
55 150485 25<br />
60 150486 25<br />
M16 65 150487 25<br />
2.0 Pitch 70 150488 25<br />
14 Key 75 150489 10<br />
80 150490 10<br />
90 150491 10<br />
100 150492 10<br />
110 150493 10<br />
120 150494 10<br />
130 150495 10<br />
140 150496 10<br />
150 150497 10<br />
160 150498 10<br />
180 150499 10<br />
200 150500 10<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
40 150501 10<br />
45 150502 10<br />
50 150503 10<br />
55 150504 10<br />
M18 60 150505 10<br />
2.5 Pitch 70 150507 10<br />
14 Key 80 150509 5<br />
90 150510 5<br />
100 150511 5<br />
110 150512 5<br />
120 150513 5<br />
130 150514 5<br />
140 150515 5<br />
Metric <strong>Fasteners</strong><br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
30 150516 5<br />
35 150517 5<br />
40 150518 5<br />
45 150519 5<br />
50 150520 5<br />
55 150521 5<br />
60 150522 1<br />
M20 65 150523 1<br />
2.5 Pitch 70 150524 1<br />
17 Key 80 150526 1<br />
90 150527 1<br />
100 150528 1<br />
110 150529 1<br />
120 150530 1<br />
130 150531 1<br />
140 150532 1<br />
150 150533 1<br />
160 150534 1<br />
180 150535 1<br />
200 150536 1<br />
Available in<br />
an Assortment<br />
PART # 00777<br />
Found on Page 79<br />
PART # 00922<br />
Found on Page 80<br />
1 800 458-4018 www.uzengprod.com<br />
257<br />
FASTENERS
FASTENERS<br />
258<br />
Metric <strong>Fasteners</strong><br />
Socket Cap Screws - Low Head<br />
• Use where socket head clearance is an issue<br />
• Black satin finish<br />
• Class 8.8<br />
• 116,000 psi tensile strength<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
M4 10 153461 25<br />
25 153465 25<br />
M5 12 153471 25<br />
16 153473 25<br />
20 153474 25<br />
25 153475 5<br />
35 153477 25<br />
M6 10 153481 25<br />
16 153484 25<br />
25 153486 25<br />
30 153487 25<br />
45 153490 25<br />
M8 16 153495 25<br />
25 153497 25<br />
45 153501 25<br />
1 800 458-4018 www.uzengprod.com
Metric Socket Set Screws<br />
• DIN 916 - Cup point. • Steel heat treated.<br />
• ISO 4029. • Black satin finish.<br />
• ANSI B 18.3.6M. • Minimum hardness - C45.<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
3 04400 50<br />
4 04401 50<br />
5 152202 50<br />
M3 6 04402 50<br />
0.5 Pitch 8 04403 50<br />
1.5 Key 10 04404 50<br />
12 04405 50<br />
16 152207 50<br />
20 152208 50<br />
4 04406 50<br />
5 04407 50<br />
6 04408 50<br />
8 04409 50<br />
M4 10 04410 50<br />
0.7 Pitch 12 04411 50<br />
2 Key 16 04412 50<br />
20 04413 50<br />
25 152217 50<br />
30 152218 50<br />
5 04414 50<br />
6 04415 50<br />
8 04416 50<br />
10 04417 50<br />
M5 12 04418 50<br />
0.8 Pitch 16 04419 50<br />
2.5 Key 20 04420 50<br />
25 04421 50<br />
30 152227 25<br />
35 152228 25<br />
40 152229 25<br />
6 04422 25<br />
8 04423 25<br />
10 04424 25<br />
M6 12 04425 25<br />
1.0 Pitch 16 04426 25<br />
3 Key 20 04427 25<br />
25 04428 25<br />
30 04429 25<br />
35 152238 25<br />
40 152239 25<br />
Metric <strong>Fasteners</strong><br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
8 04430 25<br />
10 04431 25<br />
12 04432 25<br />
16 04433 25<br />
M8 20 04434 25<br />
1.25 Pitch 25 04435 25<br />
4 Key 30 04436 25<br />
35 04437 25<br />
40 04438 25<br />
50 04439 10<br />
10 04440 25<br />
12 04441 25<br />
16 152256 25<br />
M10 20 152257 25<br />
1.5 Pitch 25 04444 25<br />
5 Key 30 04445 25<br />
35 152260 10<br />
40 04446 10<br />
50 04447 10<br />
12 152265 10<br />
16 152266 10<br />
20 152267 10<br />
M12 25 04451 10<br />
1.75 Pitch 30 04452 10<br />
6 Key 35 04453 10<br />
40 04454 10<br />
45 152272 10<br />
50 152273 10<br />
60 152274 10<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00676<br />
Found on Page 80<br />
259<br />
FASTENERS
FASTENERS<br />
260<br />
Metric <strong>Fasteners</strong><br />
Metric Flat Head Socket Cap Screws<br />
• DIN 7991-10. • IFI 535.<br />
• 150,800 PSI. • Black satin finish.<br />
• Class 12.9 • Heat treated alloy steel.<br />
DIAMETER LENGTH PART # QTY.<br />
MM<br />
6 152020 25<br />
8 152021 100<br />
M3 10 152022 25<br />
0.5 Pitch 12 152023 25<br />
2.0 Key 16 152025 100<br />
20 152026 100<br />
25 152027 100<br />
30 152028 100<br />
8 152030 25<br />
10 04800 25<br />
12 152032 25<br />
M4 14 152033 25<br />
0.7 Pitch 16 04801 25<br />
2.5 Key 20 04802 25<br />
25 04803 25<br />
30 04804 100<br />
35 04805 100<br />
40 152039 100<br />
8 152045 25<br />
10 04806 25<br />
12 152047 25<br />
M5 16 04807 25<br />
0.8 Pitch 20 04808 25<br />
3.0 Key 25 04809 25<br />
40 152054 100<br />
45 152055 25<br />
8 152060 100<br />
10 04812 25<br />
12 152062 25<br />
14 152063 25<br />
16 04813 25<br />
M6 20 04814 25<br />
1.0 Pitch 25 04815 25<br />
4.0 Key 30 04816 25<br />
35 04817 100<br />
40 152069 100<br />
45 152070 100<br />
50 152071 100<br />
55 152072 100<br />
60 152073 100<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
12 152077 100<br />
14 152078 25<br />
16 152079 25<br />
20 04818 25<br />
25 04819 25<br />
M8 30 04820 25<br />
1.25 Pitch 35 04821 100<br />
5.0 Key 40 04822 25<br />
45 152085 100<br />
50 152086 100<br />
12 152092 100<br />
16 152093 25<br />
20 152094 25<br />
25 152095 25<br />
30 152096 25<br />
M10 35 152097 100<br />
1.5 Pitch 40 152098 25<br />
6.0 Key 45 152099 25<br />
50 152100 25<br />
55 152101 50<br />
60 152102 50<br />
70 152103 50<br />
80 152104 50<br />
100 152105 50<br />
20 152106 25<br />
25 152107 50<br />
30 152108 50<br />
35 152109 50<br />
M12 40 152110 50<br />
1.75 45 152111 50<br />
8.0 Key 50 152112 25<br />
55 152113 25<br />
60 152114 25<br />
70 152115 25<br />
80 152116 25<br />
90 152117 25<br />
100 152118 25
Metric Button Head Socket Screws<br />
• ISO 7380. • Black satin finish.<br />
• 150,800 PSI. • Heat treated alloy steel.<br />
• Class 12.9<br />
DIAMETER LENGTH<br />
MM PART # QTY.<br />
M3 6 152150 25<br />
0.5 Pitch 8 152151 25<br />
2 Key 10 152152 25<br />
12 152153 100<br />
M4 8 152155 25<br />
0.7 Pitch 10 152156 25<br />
2.5 Key 12 152157 25<br />
16 152158 100<br />
10 152159 25<br />
M5 12 152160 25<br />
0.8 Pitch 16 152161 25<br />
3 Key 20 152162 25<br />
25 152163 100<br />
30 152164 100<br />
10 152165 25<br />
12 152166 25<br />
M6 14 152167 25<br />
1.0 Pitch 16 152168 25<br />
4 Key 20 152169 25<br />
25 152170 100<br />
Metric <strong>Fasteners</strong><br />
DIAMETER LENGTH<br />
MM<br />
PART # QTY.<br />
10 152172 25<br />
12 152173 25<br />
14 152174 25<br />
M8 16 152175 25<br />
1.25 Pitch 20 152176 25<br />
5 Key 25 152177 100<br />
30 152178 100<br />
35 152179 100<br />
40 152180 100<br />
16 152181 25<br />
M10 20 152182 25<br />
1.50 Pitch 25 152183 25<br />
6 Key 30 152184 100<br />
35 152185 100<br />
40 152186 100<br />
20 152188 100<br />
25 152189 100<br />
M12 30 152190 100<br />
1.75 Pitch 35 152191 100<br />
8 Key 40 152192 100<br />
45 152193 100<br />
50 152194 100<br />
1 800 458-4018 www.uzengprod.com<br />
261<br />
FASTENERS
FASTENERS<br />
262<br />
Metric Tools<br />
Metric Hex Key Wrenches<br />
• For use with socket head cap screws and set screws.<br />
• Hardened alloy steel for heavy use.<br />
USE WITH USE WITH<br />
PART # SIZE QTY. CAP SCREWS SET SCREWS<br />
04887 1.5mm 1 3mm diameter<br />
04888 2mm 1 4mm diameter<br />
04889 2.5mm 1 4mm diameter 5mm diameter<br />
04890 3mm 1 5mm diameter 6mm diameter<br />
04891 4mm 1 6mm diameter 8mm diameter<br />
04892 5mm 1 6/8mm diameter 10mm diameter<br />
04893 6mm 1 8mm diameter 12mm diameter<br />
04894 8mm 1 10mm diameter<br />
04895 10mm 1 12mm diameter<br />
Hex Key Fold-Up Metric Balldriver ® Metric Balldriver ®<br />
Metric Set Hexdriver Set L-wrench Set<br />
PART # 91582 - QTY. 1 PART # 91585 - QTY. 1 PART # 91584 - QTY. 1<br />
Handle Length: 3-1/2" Contains 9 metric sizes: Contains 9 metric sizes:<br />
Contains 7 bits in metric sizes 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10<br />
1.5, 2, 2.5, 3, 4, 5, 6 Packed in a plastic, easy lock case Packed in patented plastic key case<br />
Metric Thread Pitch Gauge<br />
• ALL STEEL CONSTRUCTION for durability.<br />
• A FULL-RANGE TOOL - each tool contains 24 blades<br />
to identify metric pitches. From 0.25 to 6.0.<br />
• STAMPED NUMBERS ON ALL BLADES - easy to<br />
read. Will not rub off.<br />
• KNURLED LOCKING-KNOBS for easy blade selection and use.<br />
PART # D0238 - QTY. 1<br />
1 800 458-4018 www.uzengprod.com
Metric Machine Screws<br />
• CLASS 4.8. • UNI-ZINC PLATED.<br />
M3<br />
0.5<br />
Pitch<br />
M4<br />
0.7<br />
Pitch<br />
PHILLIPS PHILLIPS PHILLIPS<br />
PAN HEAD FLAT HEAD OVAL HEAD<br />
DIA. LENGTH PHILLIPS QTY. PHILLIPS QTY. PHILLIPS QTY.<br />
X MM PAN FLAT OVAL<br />
PITCH HEAD HEAD HEAD<br />
4<br />
5<br />
6<br />
8<br />
10<br />
12<br />
16<br />
20<br />
25<br />
30<br />
35<br />
40<br />
45<br />
50<br />
55<br />
60<br />
5<br />
6<br />
8<br />
10<br />
12<br />
14<br />
16<br />
18<br />
20<br />
25<br />
30<br />
35<br />
40<br />
45<br />
50<br />
151700 100<br />
151701 100 151760 100 151820 100<br />
151702 100 151761 100 151821 100<br />
151703 100 151762 100 151822 100<br />
151704 100 151763 100 151823 100<br />
151705 100 151764 100 151824 100<br />
151706 100 151765 100 151825 100<br />
151707 100 151766 100 157826 100<br />
151708 100 151767 100 151827 50<br />
151709 100 151768 100 151828 50<br />
151710 50<br />
151711 50 151770 50<br />
04900 100<br />
151713 100 151771 100 151829 100<br />
04901 100 151772 100 151830 100<br />
04902 100 151773 100 151831 100<br />
04903 50 151774 50 151832 50<br />
04904 50<br />
04905 50 151775 50 151833 50<br />
04906 50<br />
04907 50 151776 50 151834 50<br />
151719 50 151777 50 151835 50<br />
151720 25 151778 25 151836 25<br />
151721 25 151779 25 151837 25<br />
151722 25 151780 25 151838 25<br />
150723 25<br />
151724 25<br />
Metric <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
263<br />
FASTENERS
FASTENERS<br />
264<br />
Metric <strong>Fasteners</strong><br />
Metric Machine Screws<br />
• CLASS 4.8. • UNI-ZINC PLATED.<br />
DIA. LENGTH PHILLIPS QTY. PHILLIPS QTY. PHILLIPS QTY.<br />
X<br />
PITCH<br />
MM<br />
6<br />
PAN FLAT OVAL<br />
8 04910 50 151781 50<br />
10 04911 50 151782 50 151840 50<br />
12 04912 50 151783 50<br />
14 04913 50<br />
16 04914 50 151784 50 151842 50<br />
M5<br />
0.8<br />
Pitch<br />
18<br />
20<br />
25<br />
04915<br />
04916<br />
04918<br />
50<br />
25<br />
25<br />
151785<br />
151786<br />
25<br />
25<br />
151843 25<br />
30 151731 25 151787 25 151845 25<br />
35 151732 25 151788 25 151846 25<br />
40 151733 25 151789 25 151847 25<br />
45 151734 25 151790 25<br />
50<br />
60<br />
8<br />
151735 25 151791 25<br />
10 04920 50 151792 50 151850 50<br />
12 04921 50 151793 50<br />
14 04922 50<br />
M6 16 04923 50 151794 50<br />
1.0 18 04924 50<br />
Pitch 20 04925 50 151795 50<br />
25 04926 50 151796 50<br />
30 04927 25 151797 25 151855 25<br />
35 151742 25 151798 25 151856 25<br />
40 151743 25 151799 25 151857 25<br />
45 151744 25 151800 25 151858 25<br />
50 151745 25 151801 25 151859 25<br />
12 151746 25 25<br />
16 151747 25 151803 25<br />
M8<br />
1.25<br />
Pitch<br />
20<br />
25<br />
30<br />
151748<br />
151749<br />
151750<br />
25<br />
25<br />
25<br />
25<br />
25<br />
25<br />
35 151751 25 25<br />
40 151752 25 25<br />
45 151753 25 25<br />
50 151754 25 25<br />
1 800 458-4018 www.uzengprod.com<br />
PHILLIPS PHILLIPS PHILLIPS<br />
PAN HEAD FLAT HEAD OVAL HEAD<br />
Available in<br />
an Assortment<br />
PART # 00674<br />
Found on Page 81<br />
PART # 00675<br />
Found on Page 81
Internal Retaining Rings<br />
Metric Retaining Rings<br />
Product Features<br />
• Compress rings into a bore or housing. Once installed, the portion of the ring protruding from the groove holds the assembly in place<br />
• Din 472<br />
• Spring Steel Phosphated<br />
• Rockwell Hardness is C47-C54<br />
RING GROOVE<br />
PART # DIAMETER THICKNESS FREE PIN HOLE B MAX C W E PKG QTY<br />
T ID D A WIDTH DIA.<br />
119300 8 0.8 8.7 1 1.1 2.4 0.9 8.4 50<br />
119301 9 0.8 9.8 1 1.4 2.5 0.9 9.4 50<br />
119302 10 1 10.8 1.2 1.6 3.2 1.1 10.4 50<br />
119303 11 1 11.8 1.2 1.6 3.3 1.1 11.4 50<br />
119304 12 1 13 1.5 2 3.4 1.1 12.5 25<br />
119305 13 1 14.1 1.5 2 3.6 1.1 13.6 25<br />
119306 14 1 15.1 1.7 2 3.7 1.1 14.6 25<br />
119307 15 1 16.2 1.7 2 3.7 1.1 15.7 25<br />
119308 16 1 17.3 1.7 2 3.8 1.1 16.8 25<br />
119309 17 1 18.3 1.7 2 3.9 1.1 17.8 25<br />
119310 18 1 19.5 2 2.5 4.1 1.1 19 25<br />
119311 19 1 20.5 2 2.5 4.1 1.1 20 25<br />
119312 20 1 21.5 2 2.5 4.2 1.1 21 25<br />
119313 21 1 22.5 2 2.5 4.2 1.1 22 25<br />
119314 22 1 23.5 2 2.5 4.2 1.1 23 25<br />
119315 23 1.2 24.6 2 2.5 4.4 1.3 24.1 25<br />
119316 24 1.2 25.9 2 2.5 4.4 1.3 25.2 25<br />
119317 25 1.2 26.9 2 3 4.5 1.3 26.2 25<br />
119318 26 1.2 27.9 2 3 4.7 1.3 27.2 10<br />
119319 27 1.2 29.1 2 3 4.7 1.3 28.4 10<br />
119320 28 1.2 30.1 2 3 4.8 1.3 29.4 10<br />
119321 29 1.2 31.1 2 3 4.8 1.3 30.4 10<br />
119322 30 1.2 32.1 2 3 4.8 1.3 31.4 10<br />
1 800 458-4018 www.uzengprod.com<br />
265<br />
FASTENERS
FASTENERS<br />
266<br />
Metric Retaining Rings<br />
External Retaining Rings<br />
Product Features<br />
• Rings expand to pass over a shaft. When released, they spring into the groove.<br />
• Din 471<br />
• Spring Steel Phosphated<br />
• Rockwell Hardness is C47-C54<br />
RING GROOVE<br />
PART # DIAMETER THICKNESS FREE PIN HOLE B MAX C W E PKG QTY<br />
T ID D A WIDTH DIA.<br />
119272 3 0.4 2.7 1 1.9 0.8 0.5 2.8 100<br />
119273 4 0.4 3.7 1 2.2 0.9 0.5 3.8 100<br />
119274 5 0.6 4.7 1 2.5 1.1 0.7 4.8 100<br />
119275 6 0.7 5.6 1.2 2.7 1.3 0.8 5.7 100<br />
119276 7 0.8 6.5 1.2 3.1 1.4 0.9 6.7 50<br />
119277 8 0.8 7.4 1.2 3.2 1.5 0.9 7.6 50<br />
119278 9 1 8.4 1.2 3.3 1.7 1.1 8.6 50<br />
119279 10 1 9.3 1.5 3.3 1.8 1.1 9.6 50<br />
119280 11 1 10.2 1.5 3.3 1.8 1.1 10.5 50<br />
119281 12 1 11 1.7 3.3 1.8 1.1 11.5 25<br />
119282 13 1 11.9 1.7 3.4 2 1.1 12.4 25<br />
119283 14 1 12.9 1.7 3.5 2.1 1.1 13.4 25<br />
119284 15 1 13.8 1.7 3.6 2.2 1.1 14.3 25<br />
119285 16 1 14.7 1.7 3.7 2.2 1.1 15.2 25<br />
119286 17 1 15.7 1.7 3.8 2.3 1.1 16.2 25<br />
119287 18 1.2 16.5 2 3.9 2.4 1.3 17 25<br />
119288 19 1.2 17.5 2 3.9 2.5 1.3 18 25<br />
119289 20 1.2 18.5 2 4 2.6 1.3 19 25<br />
119290 21 1.2 19.5 2 4.1 2.7 1.3 20 25<br />
119291 22 1.2 20.5 2 4.2 2.8 1.3 21 25<br />
119292 23 1.2 21.5 2 4.4 3 1.3 22 25<br />
119293 24 1.2 22.2 2 4.4 3 1.3 22.9 25<br />
119294 25 1.2 23.2 2 4.4 3 1.3 23.9 25<br />
119295 26 1.2 24.2 2 4.5 3.1 1.3 24.9 10<br />
119296 27 1.2 24.9 2 4.7 3.2 1.3 25.6 10<br />
119297 28 1.5 25.9 2 4.7 3.2 1.6 26.6 10<br />
119298 29 1.5 26.9 2 4.8 3.4 1.6 27.6 10<br />
119299 30 1.5 27.9 2 5 3.5 1.6 28.6 10<br />
1 800 458-4018 www.uzengprod.com
E-Type Retaining Rings<br />
Product Features<br />
• Snap rings directly into the groove from the side of the shaft.<br />
The three prongs come in contact with the bottom of the<br />
groove and provide a shoulder to effectively retain assemblies.<br />
• Din 6799<br />
• Spring Steel Phosphated<br />
• Rockwell Hardness is C46-C54.<br />
Metric Retaining Rings<br />
SHAFT DIAMETER RANGE<br />
PART # “D” FROM TO D1 MAX A S QTY<br />
119253 1.2 1.4 2 3.25 1.01 0.3 100<br />
119254 1.5 2 2.5 4.25 1.28 0.4 100<br />
119255 1.9 2.5 3 4.80 1.61 0.5 100<br />
119256 2.3 3 4 6.30 1.94 0.6 100<br />
119257 3.2 4 5 7.30 2.70 0.6 100<br />
119258 4 5 7 9.3 3.34 0.7 100<br />
119259 5 6 8 11.30 4.11 0.7 100<br />
119260 6 7 9 12.30 5.26 0.7 100<br />
119261 7 8 11 14.30 5.84 0.9 50<br />
119262 8 9 12 16.30 6.52 1.0 50<br />
119263 9 10 14 18.80 7.63 1.1 50<br />
119264 10 11 15 20.40 8.32 1.2 50<br />
119265 12 13 18 23.40 10.45 1.3 25<br />
Metric Retaining Ring Kits<br />
Two assortments to chose from<br />
• Assortments are in metal boxes.<br />
• 21 Compartments.<br />
186 Piece Set # 153452<br />
NOM. QUANTITIES<br />
SIZE DIN 471 DIN 472<br />
26 10 5<br />
28 10 5<br />
30 10 5<br />
32 10 5<br />
34 8 4<br />
35 8 4<br />
36 8 4<br />
38 8 4<br />
40 6 3<br />
42 6 3<br />
44 6 3<br />
45 6 3<br />
46 4 2<br />
48 4 2<br />
50 4 2<br />
55 4 2<br />
60 3 1<br />
65 3 1<br />
70 2 1<br />
75 2 1<br />
80 1 1<br />
2 Ring Pliers 8000 A2 8000 J2<br />
Total 186 Pcs.<br />
DIN: 6799<br />
DIN: 471<br />
DIN: 472<br />
432 Piece Set # 153451<br />
NOM. QUANTITIES<br />
SIZE DIN 6799 DIN 471 DIN 472<br />
3.2 30<br />
4 30<br />
5 30<br />
6 30<br />
7 30<br />
8 20<br />
10 20<br />
11 20 20<br />
12 20 20<br />
14 15 15<br />
15 15 15<br />
16 15 15<br />
18 10 10<br />
20 10 10<br />
22 5 5<br />
24 5 5<br />
25 5 5<br />
2 Ring Pliers 8000 A1 8000 J1<br />
Total 432 Pcs.<br />
1 800 458-4018 www.uzengprod.com<br />
267<br />
FASTENERS
FASTENERS<br />
268<br />
Metric Threaded Rod/Keystock<br />
Metric <strong>Fasteners</strong><br />
Metric Threaded Rod<br />
Carbon Steel<br />
• Made of Class 4.6 Steel<br />
• Meets or exceeds DIN975<br />
• Tensile Strength is 75,000PSI<br />
• Zinc Plated for corrosion resistance.<br />
Alloy Steel - B7<br />
• Meets ASTM specification A193-B7<br />
• Meets or exceeds DIN975<br />
• Tensile strength is 125,000 PSI<br />
• Withstands temperature up to 1000°F<br />
• Plain Finish<br />
Stainless Steel<br />
• 18/8 stainless steel - used where corrosion<br />
resistance is required<br />
• Tensile strength is 70,000 PSI<br />
Metric Rods are 1 meter in length.<br />
Keystock<br />
Product Features<br />
• Keystock is used to provide driving torque between shafts and pulleys, gears, sprockets, etc.<br />
• Used for machinery, general maintenance and shop repairs<br />
• A necessity in all applications where rotating power devices are used.<br />
• Din 6880<br />
• Carbon Steel C45 - Plain Steel<br />
• Length is 1 Meter (approximately 39")<br />
• Tolerance h9 - Rounded corners<br />
• Package QTY - 1<br />
SIZE PART NUMBER<br />
3MM X 3MM 119651<br />
3MM X 5MM 119652<br />
3MM X 6MM 119653<br />
3MM X 8MM 119654<br />
4MM X 4MM 119655<br />
4MM X 6MM 119656<br />
4MM X 7MM 119657<br />
5MM X 5MM 119658<br />
5MM X 8MM 119659<br />
6MM X 6MM 119660<br />
6MM X 8MM 119661<br />
6MM X 10MM 119662<br />
6MM X 12MM 119663<br />
6MM X 14MM 119664<br />
7MM X 7MM 119665<br />
7MM X 8MM 119666<br />
7MM X 16MM 119667<br />
7MM X 18MM 119668<br />
Available in<br />
an Assortment<br />
PART # 00994<br />
Found on Page 81<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER CARBON STEEL B7 STAINLESS STEEL<br />
2MM X 0.40 121585<br />
2.5MM X 0.45 121586<br />
3MM X 0.50 121587 121607<br />
4MM X 0.70 121588 121608<br />
5MM X 0.80 121589 121598 153823<br />
6MM X 1.0 121590 121599 153824<br />
8MM X 1.25 121591 121600 153825<br />
10MM x 1.50 121592 121601 153826<br />
12MM X 1.75 121593 121602 153827<br />
14MM X 2.0 121594 121603 153828<br />
16MM X 2.0 121595 121604 121609<br />
18MM X 2.5 121596 121605 121610<br />
20MM X 2.5 121597 121606 121611<br />
SIZE PART NUMBER<br />
8MM X 8MM 119669<br />
8MM X 10MM 119670<br />
8MM X 12MM 119671<br />
8MM X 16MM 119672<br />
8MM X 20MM 119673<br />
9MM X 14MM 119674<br />
9MM X 22MM 119675<br />
9MM X 25MM 119676<br />
10MM X 10MM 119677<br />
10MM X 12MM 119678<br />
10MM X 14MM 119679<br />
10MM X 16MM 119680<br />
10MM X 18MM 119681<br />
10MM X 20MM 119682<br />
10MM X 28MM 119683<br />
SIZE (MM) TOLERANCE h9<br />
MM INCH<br />
3 - 6 -0.030 -.0012<br />
6- 10 -0.036 -.0014<br />
10 - 18 -0.043 -.0017<br />
18 - 30 -0.052 -.0020<br />
SIZE PART NUMBER<br />
11MM X 11MM 119684<br />
11MM X 18MM 119685<br />
12MM X 12MM 119686<br />
12MM X 20MM 119687<br />
14MM X 14MM 119688<br />
14MM X 22MM 119689<br />
14MM X 25MM 119690<br />
16MM X 16MM 119691<br />
16MM X 28MM 119692<br />
18MM X 18MM 119693<br />
18MM X 32MM 119694<br />
20MM X 20MM 119695<br />
25MM X 25MM 119696
Spring Roll Pins<br />
• DIN 1481<br />
• Easily installed and reusable<br />
• Self locking<br />
• Chamfered Corners<br />
Dia Length Part # Qty<br />
M1 10 152784 25<br />
14 152786 25<br />
M1.5 10 152794 25<br />
14 152796 25<br />
M2 6 152802 25<br />
10 152804 25<br />
14 152806 25<br />
22 152810 25<br />
26 152812 25<br />
28 152813 25<br />
30 152814 25<br />
M2.5 10 152819 25<br />
M3 10 152834 25<br />
12 152835 25<br />
16 152837 25<br />
20 152839 25<br />
26 152842 25<br />
28 152843 25<br />
30 152844 25<br />
32 152845 25<br />
36 152846 25<br />
40 152847 25<br />
M3.5 10 152851 25<br />
24 152858 25<br />
26 152859 25<br />
28 152860 25<br />
30 152861 25<br />
32 152862 25<br />
36 152863 25<br />
40 152864 25<br />
M4 10 152868 25<br />
14 152870 25<br />
16 152871 25<br />
18 152872 25<br />
20 152873 25<br />
22 152874 25<br />
24 152875 25<br />
26 152876 25<br />
28 152877 25<br />
30 152878 25<br />
32 152879 25<br />
36 152880 25<br />
40 152881 25<br />
Dia Length Part # Qty<br />
M4.5 24 152889 25<br />
30 152892 25<br />
32 152893 25<br />
36 152894 25<br />
40 152895 25<br />
M5 16 152899 25<br />
20 152901 25<br />
26 152904 25<br />
28 152906 25<br />
30 152907 25<br />
M6 16 152920 25<br />
20 152922 25<br />
22 152923 25<br />
24 152924 25<br />
26 152925 25<br />
28 152926 25<br />
30 152927 25<br />
40 152930 25<br />
M8 16 152941 25<br />
20 152943 25<br />
22 152944 25<br />
24 152945 25<br />
26 152946 25<br />
28 152947 25<br />
30 152948 25<br />
40 152951 25<br />
50 152953 25<br />
M10 20 152961 25<br />
22 152962 25<br />
24 152963 25<br />
26 152964 25<br />
28 152965 25<br />
30 152966 25<br />
Metric <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
269<br />
FASTENERS
FASTENERS<br />
270<br />
18-8 Stainless Steel Metric <strong>Fasteners</strong><br />
Metric Hex Head Cap Screws<br />
• AZ-70ANSI B18.2,3,1M<br />
• ISO 4014 Per ASTMF593<br />
• DIN 933<br />
• Min Tensile Strength 689.5 MPA (80,000 PSI)<br />
M5-0.8<br />
PITCH<br />
M6-1.0<br />
PITCH<br />
M8-1.25<br />
PITCH<br />
1 800 458-4018 www.uzengprod.com<br />
M10-1.5<br />
PITCH<br />
M12-1.75<br />
PITCH
Metric Hex Head Cap Screws<br />
• AZ-70ANSI B18.2,3,1M<br />
• ISO 4014 Per ASTMF593<br />
• DIN 933<br />
• Min Tensile Strength 689.5 MPA (80,000 PSI)<br />
M14-2.0<br />
PITCH<br />
M16-2.0<br />
PITCH<br />
Available in<br />
an Assortment<br />
PART # 00452<br />
Found on Page 82<br />
18–8 Stainless Steel Metric <strong>Fasteners</strong><br />
M20-2.5<br />
PITCH<br />
M24-3.0<br />
PITCH<br />
1 800 458-4018 www.uzengprod.com<br />
271<br />
FASTENERS
FASTENERS<br />
272<br />
18-8 Stainless Steel Metric <strong>Fasteners</strong><br />
Stainless Metric Nuts and Washers<br />
• AZ-70ANSI B18.2,3,1M<br />
• ISO 4014 per ASTMF593<br />
• DIN 933<br />
• Min Tensile Strength 689.5 Mpa (80,000 PSI)<br />
1 800 458-4018 www.uzengprod.com<br />
A-Z AnSi B.18,2,4,1M<br />
Din 934<br />
A-Z AnSi B.18, 22M<br />
Din 934<br />
A-Z Din 127B
Metric Socket Head Capscrews<br />
• DIN 912<br />
• Min Tensile Strength 689.5 Mpa (80,000 PSI)<br />
M1.6-.35<br />
PITCH<br />
M2-.40<br />
PITCH<br />
M2.5-.45<br />
PITCH<br />
M3-.50<br />
PITCH<br />
M4-.70<br />
PITCH<br />
M5-.80<br />
PITCH<br />
18–8 Stainless Steel Metric <strong>Fasteners</strong><br />
M6-1.00<br />
PITCH<br />
M8-1.25<br />
PITCH<br />
M10-1.50<br />
PITCH<br />
M12-1.75<br />
PITCH<br />
Available in<br />
an Assortment<br />
153970 16 25<br />
1 800 458-4018 www.uzengprod.com<br />
PART # 00451<br />
Found on Page 82<br />
PART # 00694<br />
Found on Page 83<br />
273<br />
FASTENERS
FASTENERS<br />
274<br />
18–8 Stainless Steel Metric <strong>Fasteners</strong><br />
Socket Set Screws<br />
• Cup Point<br />
• ASTM F880M<br />
• Min Tensile Strength 689.5 MPA (80,000 PSI)<br />
M1.6-0.35<br />
PITCH<br />
M2.0-0.40<br />
PITCH<br />
M2.5-0.45<br />
PITCH<br />
M3-0.50<br />
PITCH<br />
M4-0.70<br />
PITCH<br />
M5-0.80<br />
PITCH<br />
1 800 458-4018 www.uzengprod.com<br />
M6-1.00<br />
PITCH<br />
M8-1.25<br />
PITCH<br />
M10-1.50<br />
PITCH<br />
M12-1.75<br />
PITCH<br />
Available in<br />
an Assortment<br />
PART # 00690<br />
Found on Page 83
Flat Socket Head Capscrews<br />
• Din 7991<br />
• Min Tensil Strength 689.5 Mpa (80,000 PSI)<br />
M3-.50<br />
PITCH<br />
M4-.70<br />
PITCH<br />
M5-.80<br />
PITCH<br />
M6-1.00<br />
PITCH<br />
18–8 Stainless Steel Metric <strong>Fasteners</strong><br />
M8-1.25<br />
PITCH<br />
M10-1.50<br />
PITCH<br />
M12-1.75<br />
PITCH<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 00692<br />
Found on Page 83<br />
275<br />
FASTENERS
FASTENERS<br />
276<br />
18–8 Stainless Steel Metric <strong>Fasteners</strong><br />
Button Head CapScrews<br />
• DIN 7380<br />
• Min Tensil Strength 689.5 MPA (80,000 PSI)<br />
M3-.50<br />
PITCH<br />
M4-.70<br />
PITCH<br />
M5-.80<br />
PITCH<br />
M6-1.00<br />
PITCH<br />
1 800 458-4018 www.uzengprod.com<br />
M8-1.25<br />
PITCH<br />
Available in<br />
an Assortment<br />
PART # 00691<br />
Found on Page 84
18-8 Stainless Steel <strong>Fasteners</strong><br />
Hex Head Cap Screws<br />
• 75,000-80,000 PSI Average tensile strength.<br />
• Provided superior corrosion resistance.<br />
• Manufactured under rigid quality control standards.<br />
• Cold formed.<br />
• Hardness - 100 Rockwell B.<br />
• Wide range of sizes available.<br />
18–8 Stainless Steel <strong>Fasteners</strong><br />
Provides superior corrosion resistance in applications<br />
where contact is made with...<br />
• Alcohol • Gasoline • Hydrogen sulfide • Tar<br />
• Ammonia • Carbon Dioxide • Hydrogen peroxide • Turpentine<br />
• Asphalt • Citric Acid • Milk • Whiskey<br />
• Beer • Creosote • Natural Gas • Wine<br />
• Benzene • Ethylene Glycol • Nickel Sulfate • Vinegar<br />
• Borax • Formaldehyde • Potassium Chloride • Calcium Bisulfate<br />
• Shellac<br />
...and hundreds of others!<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART # 105303<br />
Found on Page 84<br />
PART # 105304<br />
Found on Page 85<br />
1/4-20 5/16-18 3/8-16 7/16-14 1/2-13<br />
LENGTH LENGTH<br />
PART # QTY. PART # QTY. PART # QTY. PART # QTY. PART # QTY.<br />
1/2 09000 50 09015 50 09027 50 1/2<br />
5/8 09001 50 5/8<br />
3/4 09002 50 09016 50 09028 50 117552 25 09042 25 3/4<br />
7/8 09003 50 09017 50 09029 50 7/8<br />
1 09004 50 09018 50 09030 50 117553 25 09043 25 1<br />
1-1/4 09005 50 09019 50 09031 50 117554 25 09044 25 1-1/4<br />
1-1/2 09006 50 09020 50 09032 25 117555 25 09045 25 1-1/2<br />
1-3/4 09007 50 09021 50 09033 25 117556 25 09046 25 1-3/4<br />
2 09008 50 09022 50 09034 25 117557 25 09047 10 2<br />
2-1/4 09009 50 140147 25 09035 25 117558 10 140210 10 2-1/4<br />
2-1/2 09010 25 09023 25 09036 25 117559 10 09048 10 2-1/2<br />
2-3/4 09011 25 140149 25 140172 25 117560 10 140212 10 2-3/4<br />
3 09012 25 09024 25 09037 25 117561 10 09049 10 3<br />
3-1/4 140128 25 140151 25 140174 10 117562 10 140214 10 3-1/4<br />
3-1/2 09013 25 09025 25 09038 10 117563 10 09050 10 3-1/2<br />
3-3/4 140130 25 140153 25 140176 10 140216 10 3-3/4<br />
4 09014 25 09026 25 09039 10 117564 10 09051 5 4<br />
4-1/2 09040 10 117565 5 09052 5 4-1/2<br />
5 140133 25 09041 10 117566 5 09053 5 5<br />
5-1/2 140134 25 117567 5 140220 5 5-1/2<br />
6 140135 25 117568 5 09054 5 6<br />
Hex Nut 09083 100 09084 100 09085 100 117569 50 09086 50 Hex Nut<br />
Flatwasher 09092 100 09093 100 09094 100 117570 50 09095 50 Flatwasher<br />
Lockwasher 09101 100 09102 100 09103 50 117571 50 09104 50 Lockwasher<br />
Nylon Insert 140430<br />
Locknut<br />
100 140431 100 140432 50 117572 50 140433 50<br />
Nylon Insert<br />
Locknut<br />
277<br />
FASTENERS
FASTENERS<br />
278<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Hex Head Cap Screws<br />
LENGTH<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
3-3/4<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
Hex Nut<br />
Flatwasher<br />
Lockwasher<br />
Nylon Insert<br />
Locknut<br />
5/8-11<br />
PART # QTY<br />
09055 10<br />
09056 10<br />
09057 10<br />
09058 10<br />
09059 10<br />
09060 10<br />
09061 10<br />
140234 10<br />
09062 5<br />
140236 5<br />
09063 5<br />
140238 5<br />
09064 5<br />
09065 5<br />
09066 5<br />
140242 5<br />
09067 5<br />
09087 25<br />
09096 25<br />
09105 25<br />
140434 25<br />
18-8 Stainless Steel Serrated Hex Nuts<br />
1 800 458-4018 www.uzengprod.com<br />
3/4-10 7/8-9 1-8<br />
PART # QTY. PART #QTY. PART #QTY.<br />
140248 5<br />
140249 5<br />
09068 5 140269 5<br />
09069 5 140270 5<br />
09070 5 140271 5 140287 5<br />
09071 5 140272 5 140288 5<br />
09072 5 140273 5 140289 5<br />
140255 5 140274 5 140290 5<br />
09073 5 140275 5 140291 5<br />
140257 5 140276 5 140292 5<br />
09074 5 140277 5 140293 5<br />
140278 5 140294 5<br />
09075 5 140279 5 140295 5<br />
09076 5 140280 5 140296 5<br />
09077 5 140281 5 140297 5<br />
140263 5 140282 5 140298 5<br />
09078 5 140283 5 140299 5<br />
09088 25 140419 5 140420 5<br />
09097 25 140472 25 140473 25<br />
09106 25 140453 10 140454 10<br />
• Serrated flange on the nuts covers oversized holes.<br />
• Serrations help to grip tighter to material being fastened, eliminating the use of lock washers.<br />
• The size of the flange distributes the load over a greater area, therefore it will require more torque to remove the nut<br />
• Superior corrosion resistance.<br />
PART # SIZE OVERALL HT FLANGE DIA. QTY.<br />
122234 6-32 11/64" 27/64" 100<br />
122235 8-32 13/64" 15/32" 100<br />
122236 10-24 7/32" 1/2" 100<br />
122237 10-32 7/32" 1/2" 100<br />
PART # SIZE OVERALL HT FLANGE DIA. QTY.<br />
122238 1/4-20 15/64" 19/32" 100<br />
122239 5/16-18 9/32" 11/16" 50<br />
122240 3/8-16 11/32" 3/4" 25<br />
122241 1/2-13 25/64" 1-1/32" 10<br />
LENGTH<br />
1/2<br />
5/8<br />
3/4<br />
7/8<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
3-3/4<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
Hex Nut<br />
Flatwasher<br />
Lockwasher
Hex Machine Screw Nuts<br />
• Superior corrosion resistance.<br />
• Precision finished threads for trouble-free assembly.<br />
• Double chamfered for greater assembly speed.<br />
• Manufactured to exacting quality control standards.<br />
PART # SIZE WIDTH<br />
ACROSS<br />
FLATS<br />
THICKNESS QTY.<br />
09489 0-80 5/32 3/64 100<br />
09490 1-72 5/32 3/64 100<br />
09491 2-56 3/16 1/16 100<br />
09492 3-48 3/16 1/16 100<br />
09493 4-40 1/4 3/32 100<br />
09494 5-40 5/16 7/64 100<br />
09079 6-32 5/16 7/64 100<br />
09080 8-32 11/32 1/8 100<br />
09081 10-24 3/8 1/8 100<br />
09082 10-32 3/8 1/8 100<br />
140391 1/4-20 7/16 5/32 100<br />
140392 5/16-18 9/16 7/32 100<br />
Nylon Insert Lock Nuts<br />
• Keeps fastener assemblies tight even when<br />
vibration is present.<br />
• Use with 18-8 stainless steel cap screws<br />
and machine screws.<br />
• Superior corrosion resistance.<br />
PART # SIZE<br />
WIDTH<br />
ACROSS THICKNESS<br />
FLATS<br />
QTY.<br />
09495 2-56 1/4 5/32 50<br />
09496 4-40 1/4 5/32 100<br />
09497 6-32 5/16 11/64 100<br />
09498 8-32 11/32 7/32 100<br />
09499 10-24 3/8 15/64 100<br />
140429 10-32 3/8 15/64 100<br />
140430 1/4-20 7/16 5/16 100<br />
140431 5/16-18 1/2 11/32 100<br />
140432 3/8-16 9/16 29/64 50<br />
117572 7/16-14 5/8 29/64 50<br />
140433 1/2-13 3/4 19/32 50<br />
140434 5/8-11 15/16 3/4 25<br />
Available in<br />
an Assortment<br />
PART #00796<br />
Found on Page 85<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Finished Hex Nuts<br />
• Superior corrosion resistance.<br />
• Finished full for greater strength.<br />
• Clear-burr free threads for trouble-free assembly.<br />
• Washer faced for positive seating.<br />
PART # SIZE WIDTH<br />
ACROSS<br />
FLATS<br />
THICKNESS QTY.<br />
09083 1/4-20 7/16 7/32 100<br />
09084 5/16-18 1/2 17/64 100<br />
09085 3/8-16 9/16 21/64 100<br />
117569 7/16-14 11/16 3/8 50<br />
09086 1/2-13 3/4 7/16 50<br />
09087 5/8-11 15/16 35/64 25<br />
09088 3/4-10 1-1/8 41/64 25<br />
140419 7/8-9 1-5/16 3/4 5<br />
140420 1-8 1-1/2 55/64 5<br />
Acorn Cap Nuts<br />
• Closed top for safety.<br />
• Use where appearance is important.<br />
• Superior corrosion resistance.<br />
PART # SIZE QTY.<br />
147805 4-40 25<br />
147806 6-32 25<br />
147807 8-32 25<br />
147808 10-24 25<br />
147809 10-32 25<br />
147810 1/4-20 25<br />
147811 5/16-18 10<br />
147812 3/8-16 10<br />
147813 1/2-13 5<br />
147814 5/8-11 5<br />
147815 3/4-10 5<br />
Wing Nuts<br />
• Superior corrosion resistance.<br />
PART # SIZE QTY.<br />
147816 6-32 25<br />
147817 8-32 25<br />
147818 10-24 25<br />
147819 10-32 25<br />
147820 1/4-20 25<br />
147821 5/16-18 25<br />
147822 3/8-16 10<br />
147823 1/2-13 5<br />
147824 5/8-11 5<br />
1 800 458-4018 www.uzengprod.com<br />
279<br />
FASTENERS
FASTENERS<br />
280<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Flat Washers<br />
• Superior corrosion resistance.<br />
• Resists bending, dishing & distorting.<br />
• Exacting quality control.<br />
PART # SIZE INSIDE OUTSIDE QTY.<br />
DIA. DIA.<br />
09483 #0 .068 3/16 200<br />
09484 #1 .084 3/16 200<br />
09485 #2 .094 1/4 200<br />
09486 #3 .109 1/4 200<br />
09487 #4 .125 5/16 200<br />
09488 #5 .141 5/16 200<br />
09089 #6 .149 3/8 200<br />
09090 #8 .174 3/8 200<br />
09091 #10 .203 7/16 200<br />
09092 1/4 .281 5/8 100<br />
09093 5/16 .344 3/4 100<br />
09094 3/8 .406 7/8 100<br />
117570 7/16 .500 1-1/4 50<br />
09095 1/2 .563 1-1/4 50<br />
09096 5/8 .688 1-1/2 25<br />
09097 3/4 .812 1-3/4 25<br />
140472 7/8 .938 2 25<br />
140473 1 1.062 2 25<br />
18-8 Stainless Oversize<br />
(Fender) Washers<br />
PART # BOLT OUTSIDE NOMINAL QTY.<br />
SIZE DIA. THICKNESS<br />
111074 3/16 (#10) 3/4 1/16 100<br />
111075 3/16 (#10) 1 1/16 100<br />
111076 1/4 1 1/16 100<br />
111077 1/4 1-1/4 1/16 100<br />
111078 1/4 1-1/2 1/16 50<br />
111079 1/4 2 1/16 25<br />
111080 5/16 1 1/16 100<br />
111081 5/16 1-1/4 1/16 100<br />
111082 5/16 1-1/2 1/16 50<br />
111083 5/16 2 1/16 25<br />
111084 3/8 1-1/4 1/16 100<br />
111085 3/8 1-1/2 1/16 50<br />
111086 3/8 2 1/16 25<br />
111087 1/2 1-1/2 1/16 25<br />
111088 1/2 2 1/16 25<br />
1 800 458-4018 www.uzengprod.com<br />
Lock Washers<br />
• Superior corrosion resistance.<br />
• Positive spring action for positive locking.<br />
• Manufactured to rigid quality control standards.<br />
• Close tolerance for better fit.<br />
PART # SIZE INSIDE OUTSIDE QTY.<br />
DIA. DIA.<br />
140440 #4 0.120 0.209 250<br />
09098 #6 0.148 0.250 250<br />
09099 #8 0.174 0.293 250<br />
09100 #10 0.200 0.334 250<br />
09101 1/4 0.260 0.487 100<br />
09102 5/16 0.322 0.583 100<br />
09103 3/8 0.385 0.680 50<br />
117571 7/16 0.450 0.776 50<br />
09104 1/2 0.512 0.869 50<br />
09105 5/8 0.641 1.073 25<br />
09106 3/4 0.766 1.265 25<br />
140453 7/8 0.894 1.459 10<br />
140454 1 1.024 1.656 10<br />
Countersunk Finishing Washers<br />
• Formed circular washer design for use with<br />
flat or oval head screws.<br />
• Convex shaped.<br />
• Designed for accommodating the heads of countersunk screws-<br />
providing additional bearing area on the material being fastened.<br />
• Provides a neat, finishing appearance.<br />
• Excellent corrosion resistance.<br />
PART # SIZE INSIDE OUTSIDE QTY.<br />
DIA. DIA.<br />
117917 #4 .150- .120 3/8 100<br />
117918 #6 .200- .170 15/32 100<br />
117919 #8 .210- .180 17/32 100<br />
117920 #10 .265- .235 19/32 100<br />
117921 #12 .289-.259 21/32 100<br />
117922 1/4 .335- .305 25/32 100<br />
117923 5/16 .409-.373 15/16 50<br />
117924 3/8 .460-.425 1-1/8 50
410 S/S Internal & External Tooth Lockwashers<br />
• Manufactured from 410 S/S - more magnetic than 18/8 S/S<br />
• Corrosion resistant.<br />
• Rockwell hardness is C34.<br />
• INTERNAL type - teeth lock into screw head to prevent loosening. Used to prevent snagging or<br />
scratching and where appearances warrants that the teeth be hidden.<br />
• EXTERNAL type - provide maximum holding power with screws that have large enough heads to<br />
make contact with the washer teeth - such as round or pan head screws.<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
BOLT 410 S/S INTERNAL TOOTH 410 S/S EXTERNAL TOOTH<br />
SIZE LOCKWASHER LOCKWASHER QTY.<br />
PART # ID (in.) OD (in.) PART # ID (in.) OD (in.)<br />
#4 120095 0.123 0.270 120107 0.115 0.260 100<br />
#6 120096 0.150 0.295 120108 0.141 0.320 100<br />
#8 120097 0.176 0.340 120109 0.168 0.381 100<br />
#10 120098 0.204 0.381 120702 0.195 0.410 100<br />
#12 120099 0.231 0.410 120704 0.221 0.475 100<br />
1/4 120100 0.267 0.478 120112 0.256 0.510 100<br />
5/16 120101 0.332 0.610 120705 0.320 0.610 100<br />
3/8 120102 0.398 0.692 120114 0.384 0.694 100<br />
7/16 120103 0.464 0.789 120115 0.448 0.760 50<br />
1/2 120104 0.530 0.900 120116 0.513 0.900 50<br />
5/8 120105 0.663 1.071 120117 0.641 1.070 25<br />
3/4 120106 0.795 1.245 120118 0.768 1.26 25<br />
Available in<br />
an Assortment<br />
PART #00927<br />
Found on Page 86<br />
PART #00928KP<br />
Found on Page 86<br />
PART #00929KP<br />
Found on Page 86<br />
1 800 458-4018 www.uzengprod.com<br />
281<br />
FASTENERS
FASTENERS<br />
282<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Socket Head Cap Screws<br />
• Superior corrosion resistance.<br />
• Deep sockets for easy wrenching.<br />
• Manufactured under rigid quality<br />
control standards.<br />
DIAMETER LENGTH PART #<br />
USS (NC) SAE (NF)<br />
QTY.<br />
#4 1/4 141117 100<br />
USS = 40 3/8 141118 100<br />
(3/32 Key) 1/2 141119 100<br />
1/4 141135 100<br />
#6 3/8 141136 100<br />
USS = 32 1/2 141137 100<br />
(7/64 Key) 5/8 141138 100<br />
3/4 141139 100<br />
#8 3/8 141147 100<br />
USS = 32 1/2 141148 100<br />
(9/64 Key) 5/8 141149 100<br />
3/4 141150 100<br />
1 141152 100<br />
3/8 141159 141435 100<br />
#10 1/2 141160 141436 100<br />
USS = 24 5/8 141161 141437 100<br />
SAE = 32 3/4 141162 141438 100<br />
(5/32 Key) 1 141164 141440 100<br />
1-1/4 141165 141441 100<br />
1-1/2 141166 141442 100<br />
3/8 141173 100<br />
1/2 141174 141450 100<br />
1/4 5/8 141175 141451 100<br />
USS = 20 3/4 141176 141452 100<br />
SAE = 28 1 141178 141454 100<br />
(3/16 Key) 1-1/4 141179 141455 50<br />
1-1/2 141180 141456 50<br />
1-3/4 141181 50<br />
2 141182 50<br />
Available in<br />
an Assortment<br />
PART #00793<br />
Found on Page 87<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH PART #<br />
USS (NC) SAE (NF)<br />
QTY.<br />
1/2 141191 50<br />
5/8 141193 50<br />
3/4 141194 141466 50<br />
5/16 1 141196 141468 50<br />
USS = 18 1-1/4 141197 141469 50<br />
SAE = 24 1-1/2 141198 141470 25<br />
(1/4 Key) 1-3/4 141199 25<br />
2 141200 25<br />
2-1/4 141201 10<br />
2-1/2 141202 10<br />
1/2 141211 50<br />
3/4 141213 141481 50<br />
3/8 1 141215 141483 50<br />
USS = 16 1-1/4 141216 141484 25<br />
SAE = 24 1-1/2 141217 141485 25<br />
(5/16 Key) 1-3/4 141218 25<br />
2 141219 25<br />
2-1/4 141220 25<br />
2-1/2 141221 25<br />
3/4 141255 10<br />
1 141257 10<br />
1/2 1-1/4 141258 10<br />
USS = 13 1-1/2 141259 10<br />
(1/4 Key) 1-3/4 141260 10<br />
2 141261 10<br />
2-1/2 141263 10<br />
3 141265 10<br />
1 141280 10<br />
1-1/4 141281 10<br />
5/8 1-1/2 141282 10<br />
USS = 11 1-3/4 141283 10<br />
(1/2 Key) 2 141284 10<br />
2-1/2 141286 10<br />
3 141288 10
18-8 Flat Head Socket Cap Screws<br />
• Provides superior corrosion resistance.<br />
• For all countersunk applications.<br />
• Deep, fully formed hex for easier wrenching.<br />
DIAMETER LENGTH PART # QTY.<br />
USS (NC) SAE (NF)<br />
#2 3/16 120488 100<br />
USS = 56 1/4 120489 100<br />
(.050 Key) 5/16 120490 100<br />
3/8 120491 100<br />
1/4 141910 100<br />
5/16 120492 100<br />
#4 3/8 141912 100<br />
USS = 40 1/2 141914 100<br />
(1/16 Key) 5/8 120493 100<br />
3/4 120494 100<br />
1/4 141919 100<br />
5/16 120495 100<br />
#6 3/8 141920 100<br />
USS = 32 1/2 141921 100<br />
(5/64 Key) 5/8 141922 100<br />
3/4 141923 100<br />
1 120496 100<br />
1/4 120497 100<br />
5/16 120498 100<br />
#8 3/8 141928 100<br />
USS = 32 1/2 141929 100<br />
(3/32 Key) 5/8 141930 100<br />
3/4 141931 100<br />
1 141932 100<br />
3/8 141937 142048 100<br />
1/2 141938 142050 100<br />
#10 5/8 141939 142051 100<br />
USS = 24 3/4 141940 142052 100<br />
SAE = 32 1 141941 142054 100<br />
(1/8 Key) 1-1/4 141942 120500 100<br />
1-1/2 120499 120501 100<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
DIAMETER LENGTH PART # QTY.<br />
USS (NC) SAE (NF)<br />
3/8 141947 100<br />
1/2 141949 100<br />
1/4 5/8 141950 100<br />
USS = 20 3/4 141951 100<br />
(5/32 Key) 7/8 120502 100<br />
1 141952 100<br />
1-1/4 141953 50<br />
1-1/2 141954 50<br />
1-3/4 120503 50<br />
2 120504 50<br />
2-1/2 120505 25<br />
1/2 141962 50<br />
5/8 141963 50<br />
3/4 141964 50<br />
5/16 1 141965 50<br />
USS = 18 1-1/4 141966 50<br />
(3/16 Key) 1-1/2 151967 25<br />
1-3/4 141968 25<br />
2 141969 25<br />
2-1/2 120506 25<br />
3 120507 25<br />
1/2 120508 25<br />
3/4 141978 25<br />
3/8 1 141979 25<br />
USS = 16 1-1/4 141980 25<br />
(7/32 Key) 1-1/2 141981 25<br />
1-3/4 141982 25<br />
2 141983 25<br />
3/4 120509 25<br />
1 120510 25<br />
1/2 1-1/4 120511 25<br />
USS = 13 1-1/2 120512 25<br />
(5/16 Key) 1-3/4 120513 10<br />
2 120514 10<br />
2-1/2 120515 10<br />
3 120516 10<br />
1 120517 5<br />
5/8 1-1/4 120518 5<br />
USS = 11 1-1/2 120519 5<br />
(3/8 Key) 2 120520 5<br />
2-1/2 120521 5<br />
2-3/4 120522 5<br />
3 120523 5<br />
1 800 458-4018 www.uzengprod.com<br />
283<br />
FASTENERS
FASTENERS<br />
284<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
18-8 Button Head Socket Cap Screws<br />
• Provides superior corrosion resistance.<br />
• For above surface applications.<br />
DIAMETER LENGTH PART # QTY.<br />
USS (NC) SAE (NF)<br />
#2 1/8 120524 100<br />
USS = 56 3/16 120525 100<br />
(.050 Key) 1/4 120526 100<br />
5/16 120527 100<br />
3/8 120528 100<br />
1/2 120529 100<br />
1/8 120530 100<br />
3/16 120531 100<br />
1/4 142381 100<br />
#4 5/16 120532 100<br />
USS = 40 3/8 142382 100<br />
(1/16 Key) 7/16 120533 100<br />
1/2 142383 100<br />
5/8 120534 100<br />
3/4 120535 100<br />
1 120536 100<br />
3/16 120537 100<br />
1/4 142388 100<br />
#6 5/16 120538 100<br />
USS = 32 3/8 142389 100<br />
(5/64 Key) 7/16 120539 100<br />
1/2 142390 100<br />
5/8 142391 100<br />
3/4 120540 100<br />
7/8 120541 100<br />
1 120542 100<br />
1/4 142396 100<br />
5/16 120543 100<br />
#8 3/8 142397 100<br />
USS = 32 1/2 142398 100<br />
(3/32 Key) 5/8 142399 100<br />
3/4 142400 100<br />
7/8 120544 100<br />
1 120545 100<br />
Available in<br />
an Assortment<br />
PART #00924<br />
Found on Page 87<br />
PART #00925<br />
Found on Page 87<br />
1 800 458-4018 www.uzengprod.com<br />
DIAMETER LENGTH PART # QTY.<br />
USS (NC) SAE (NF)<br />
1/4 142405 142501 100<br />
5/16 120546 120551 100<br />
#10 3/8 142406 142503 100<br />
USS = 24 1/2 142407 142505 100<br />
SAE = 32 5/8 142408 142506 100<br />
(1/8 Key) 3/4 142409 142507 100<br />
7/8 120547 120552 100<br />
1 120548 120553 100<br />
1-1/4 120549 120554 100<br />
1-1/2 120550 120555 100<br />
2 120556 50<br />
3/8 142416 100<br />
1/2 142417 100<br />
5/8 142418 100<br />
1/4 3/4 142419 100<br />
USS = 20 7/8 120557 100<br />
(5/32 Key) 1 142421 100<br />
1-1/4 120558 50<br />
1-1/2 120559 50<br />
1-3/4 120560 50<br />
2 120561 50<br />
1/2 120562 50<br />
5/8 120563 50<br />
5/16 3/4 142429 50<br />
USS=18 1 142431 50<br />
(3/16 Key) 1-1/4 120564 50<br />
1-1/2 120565 25<br />
1-3/4 120566 25<br />
2 120567 25<br />
3/8 3/4 142438 50<br />
USS = 16 1 142440 50<br />
(7/32 Key) 1-1/4 142441 25<br />
1-1/2 120568 25<br />
1/2 1 120569 10<br />
USS = 13 1-1/4 120570 10<br />
(5/16 Key) 1-1/2 120571 10
Hex Socket Set Screws - Cup Point<br />
• Superior corrosion resistance.<br />
DIAMETER LENGTH PART #<br />
USS (NC) SAE (NF)<br />
QTY.<br />
#4 1/8 141549 100<br />
USS = 40 3/16 141550 100<br />
(.050 Key) 1/4 141551 100<br />
1/8 141574 100<br />
#6 3/16 141575 100<br />
USS = 32 1/4 141576 100<br />
(1/16 Key) 5/16 141577 100<br />
3/8 141578 100<br />
1/8 141589 100<br />
#8 3/16 141590 100<br />
USS = 32 1/4 141591 100<br />
(5/64 Key) 5/16 141592 100<br />
3/8 141593 100<br />
1/2 141595 100<br />
3/16 141604 141817 100<br />
#10 1/4 141605 141818 100<br />
USS = 24 5/16 141606 141819 100<br />
SAE = 32 3/8 141607 141820 100<br />
(3/32 Key) 1/2 141609 141822 100<br />
5/8 141610 141823 100<br />
3/4 141611 141824 100<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
DIAMETER LENGTH PART #<br />
USS (NC)<br />
QTY.<br />
3/16 141619 100<br />
1/4 141620 100<br />
1/4 5/16 141621 100<br />
USS = 20 3/8 141622 100<br />
(1/8 Key) 1/2 141624 100<br />
5/8 141625 100<br />
3/4 141626 100<br />
1 141628 100<br />
1/4 141637 100<br />
5/16 5/16 141638 100<br />
USS = 18 3/8 141639 100<br />
(5/32 Key) 1/2 141641 100<br />
3/4 141643 100<br />
1 141645 100<br />
5/16 141655 100<br />
3/8 3/8 141656 100<br />
USS = 16 1/2 141658 100<br />
(3/16 Key) 5/8 141659 100<br />
3/4 141660 100<br />
1 141662 100<br />
1/2 1/2 141690 100<br />
USS = 13 5/8 141691 100<br />
(1/4 Key) 3/4 141692 100<br />
1 141694 100<br />
Available in<br />
an Assortment<br />
PART #00795<br />
Found on Page 88<br />
1 800 458-4018 www.uzengprod.com<br />
285<br />
FASTENERS
FASTENERS<br />
286<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Extended Prong (Efficiency) Cotter Pins<br />
• Superior corrosion resistance.<br />
• Provide positive locking action.<br />
DIAMETER LENGTH PART # QTY.<br />
1/2 140800 200<br />
1/16 3/4 140801 200<br />
1 140802 200<br />
1-1/2 140803 200<br />
3/4 140805 100<br />
5/64 1 140806 100<br />
1-1/2 140807 100<br />
1/2 140808 100<br />
3/4 140809 100<br />
3/32 1 140810 100<br />
1-1/2 140811 100<br />
2 140812 100<br />
1/2 140813 100<br />
3/4 140814 100<br />
1 140815 100<br />
1/8 1-1/4 140816 100<br />
1-1/2 140817 100<br />
1-3/4 140818 100<br />
2 140819 50<br />
2-1/2 140820 50<br />
1 140821 50<br />
5/32 1-1/4 140822 50<br />
1-1/2 140823 50<br />
2 140824 50<br />
1 140825 50<br />
1-1/4 140826 50<br />
3/16 1-1/2 140827 25<br />
2 140828 25<br />
2-1/2 140829 25<br />
3 140830 25<br />
1 140831 25<br />
1-1/4 140832 25<br />
1-1/2 140833 25<br />
1/4 2 140834 25<br />
2-1/2 140835 10<br />
3 140836 10<br />
3-1/2 140837 10<br />
4 140838 10<br />
1 800 458-4018 www.uzengprod.com
Carriage Bolts<br />
• Superior corrosion resistance.<br />
• Clean, burr-free rolled threads.<br />
• Fully formed square shoulders.<br />
• Highest quality available.<br />
DIAMETER LENGTH PART # QTY.<br />
1/2 147825 50<br />
5/8 147826 50<br />
3/4 147827 50<br />
1 147828 50<br />
1-1/4 147829 50<br />
1/4-20 1-1/2 147830 50<br />
1-3/4 147831 25<br />
2 147832 25<br />
2-1/4 147833 25<br />
2-1/2 147834 25<br />
3 147835 25<br />
3-1/2 147836 25<br />
4 147837 25<br />
3/4 147838 50<br />
1 147839 25<br />
1-1/4 147840 25<br />
1-1/2 147841 25<br />
5/16-18 1-3/4 147842 25<br />
2 147843 25<br />
2-1/2 147844 25<br />
3 147845 25<br />
3-1/2 147846 10<br />
4 147847 10<br />
3/4 147848 25<br />
1 147849 25<br />
1-1/4 147850 25<br />
1-1/2 147851 25<br />
3/8-16 1-3/4 147852 25<br />
2 147853 10<br />
2-1/4 147854 10<br />
2-1/2 147855 10<br />
3 147856 10<br />
3-1/2 147857 10<br />
4 147858 10<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Hex Head Lag Screws<br />
• Superior corrosion resistance.<br />
• Sharp point for easy starting.<br />
• Manufacturing to rigid standards.<br />
• Hex head for easy wrenching.<br />
DIAMETER LENGTH PART # QTY.<br />
1 147859 25<br />
1-1/4 147860 25<br />
1-1/2 147861 25<br />
2 147862 10<br />
1/4 2-1/2 147863 10<br />
3 147864 10<br />
3-1/2 147865 10<br />
4 147866 5<br />
4-1/2 147867 5<br />
5 147868 5<br />
1 147869 10<br />
1-1/4 147870 10<br />
1-1/2 147871 10<br />
2 147872 10<br />
5/16 2-1/2 147873 10<br />
3 147874 10<br />
3-1/2 147875 5<br />
4 147876 5<br />
4-1/2 147877 5<br />
5 147878 5<br />
1 147879 10<br />
1-1/4 147880 10<br />
1-1/2 147881 10<br />
1-3/4 147882 10<br />
2 147883 10<br />
3/8 2-1/2 147884 10<br />
3 147885 5<br />
3-1/2 147886 5<br />
4 147887 5<br />
4-1/2 147888 5<br />
5 147889 5<br />
1-1/2 147890 5<br />
2 147891 5<br />
2-1/2 147892 5<br />
1/2 3 147893 5<br />
3-1/2 147894 5<br />
4 147895 5<br />
4-1/2 147896 5<br />
5 147897 5<br />
1 800 458-4018 www.uzengprod.com<br />
287<br />
FASTENERS
FASTENERS<br />
288<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Machine Screws<br />
• Deep twist resistant slots.<br />
• Provide superior corrosion resistance.<br />
• Manufactured under rigid quality control standards.<br />
• Wide range of sizes available.<br />
DIA. LENGTH PHILLIPS PHILLIPS<br />
PAN FLAT<br />
HEAD QTY HEAD QTY<br />
2-56 1/8 109653 100 109724 100<br />
3/16 109654 100 109725 100<br />
1/4 109655 100 109726 100<br />
5/16 109656 100 109727 100<br />
2-56 3/8 109657 100 109728 100<br />
1/2 109658 100 109729 100<br />
5/8 109659 100 109730 100<br />
3/4 109660 100 109731 100<br />
1 109661 100 109732 100<br />
3-48 1/8 109662 100 109733 100<br />
3/16 109663 100 109734 100<br />
1/4 109664 100 109735 100<br />
3-48 5/16 109665 100 109736 100<br />
3/8 109666 100 109737 100<br />
1/2 109667 100 109738 100<br />
5/8 109668 100 109739 100<br />
3/4 109669 100 109740 100<br />
4-40 3/16 109670 100 109741 100<br />
1/4 109671 100 109742 100<br />
5/16 109672 100 109743 100<br />
3/8 109673 100 109744 100<br />
7/16 109674 100 109745 100<br />
4-40 1/2 109675 100 109746 100<br />
5/8 109676 100 109747 100<br />
3/4 109677 100 109748 100<br />
1 109678 100 109749 100<br />
1-1/4 109679 100 109750 100<br />
1-1/2 109680 100 109751 100<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #00542<br />
Found on Page 88<br />
PART #00797<br />
Found on Page 88<br />
PART #00798<br />
Found on Page 89<br />
PART #00798KP<br />
Found on Page 89
Machine Screws<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Phillips Pan Phillips Flat Phillips Oval Hex Head<br />
DIA. LENGTH PHILLIPS PHILLIPS PHILLIPS<br />
PAN FLAT OVAL<br />
HEAD QTY HEAD QTY HEAD QTY<br />
6-32 1/8 09238 100<br />
3/16 09239* 100 109752 50<br />
1/4 09240 50 109753 50<br />
5/16 09241 50 109754 50 09224 50<br />
3/8 09242 50 109755 50 09225 50<br />
7/16 09243* 100 109756 50<br />
1/2 09244 50 109757 50 09226 50<br />
6-32<br />
5/8 09245* 100 109758 50<br />
3/4 09246 50 109759 50 09227 50<br />
7/8 09247 50<br />
1 09248 50 109760 50<br />
1-1/4 109681 50 109761 50<br />
1-1/2 109682 50 109762 50<br />
2 109683 25 109763 50<br />
2-1/2 109684 25 109764 50<br />
3 109685 25 109765 50<br />
8-32 3/16 09249 100<br />
1/4 09250 50 109766 50<br />
5/16 09251* 100 109767 50<br />
3/8 09252 50 109768 50 09228 50<br />
7/16 09253* 100 109769 50<br />
1/2 09254 50 109770 50 09229 50<br />
5/8 09255 50 109771 50 09230 50<br />
3/4 09256 50 109772 50 09231 50<br />
8-32 7/8 09257 100<br />
1 09258 50 109773 50 09232 50<br />
1-1/4 109686 50 109774 50<br />
1-1/2 109687 50 109775 50 09233 25<br />
1-3/4 109688 50 109776 50<br />
2 109689 25 109777 25<br />
2-1/4 109690 25 109778 25<br />
2-1/2 109691 25 109779 25<br />
3 109692 25 109780 25<br />
HEX<br />
HEAD<br />
120135<br />
120136<br />
120137<br />
120138<br />
120139<br />
120140<br />
120141<br />
120142<br />
120143<br />
120144<br />
120145<br />
120146<br />
120147<br />
120148<br />
120149<br />
120150<br />
1 800 458-4018 www.uzengprod.com<br />
QTY<br />
100<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
100<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
289<br />
FASTENERS
FASTENERS<br />
290<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Machine Screws<br />
Phillips Pan Phillips Flat Phillips Oval Hex Head<br />
DIA. LENGTH PHILLIPS PHILLIPS PHILLIPS<br />
PAN FLAT OVAL<br />
HEAD QTY HEAD QTY HEAD QTY<br />
1/4 09259 50 109781 50<br />
5/16 09260 50 109782 50<br />
3/8 09261 50 109783 50<br />
7/16 09262 50 109784 50<br />
1/2 09263 50 109785 50<br />
5/8 09264 50 109786 50<br />
3/4 09265 50 109787 50<br />
10-24<br />
7/8 09266 50<br />
1 09267 50 109788 50<br />
1-1/4 109693 50 109789 50<br />
1-1/2 109694 50 109790 50<br />
1-3/4 109695 50 109791 50<br />
2 109696 50 109792 25<br />
2-1/2 109697 50 109793 25<br />
3 109698 50 109794 25<br />
3-1/2 109699 50 109795 25<br />
1/4 09268 50 109796 50<br />
5/16 109701 50 109797 50<br />
3/8 09270 50 109798 50<br />
7/16 109702 50 109799 50<br />
1/2 09272 50 109800 50 09234 50<br />
5/8 09273 50 109801 50 09235 50<br />
3/4 09274 50 109802 50 09236 50<br />
10-32<br />
7/8<br />
1<br />
09275<br />
09276<br />
50<br />
50<br />
109803<br />
109804<br />
50<br />
50 09237 50<br />
1-1/4 109703 50 109805 50<br />
1-1/2 109704 50 109806 50<br />
1-3/4 109705 50 109807 25<br />
2 109706 25 109808 25<br />
2-1/2 109707 25 109809 25<br />
3<br />
3-1/2<br />
109708 25 109810 25<br />
3/8 109709 25 109811 25<br />
7/16 109710 25<br />
1/2 109711 25 109812 25<br />
5/8 109712 25 109813 25<br />
3/4 109713 25 109814 25<br />
7/8 109714 25<br />
1 109715 25 109815 25<br />
1/4-20 1-1/4 109716 25 109816 25<br />
1-1/2 109717 25 109817 25<br />
1-3/4 109718 25 109818 25<br />
2 109719 25 109819 25<br />
2-1/2 109720 25 109820 25<br />
3 109721 25 109821 25<br />
3-1/2 109722 25 109822 25<br />
4 109723 25 109823 25<br />
1 800 458-4018 www.uzengprod.com<br />
HEX<br />
HEAD<br />
120151<br />
120152<br />
120153<br />
120154<br />
120155<br />
120156<br />
120157<br />
120158<br />
120159<br />
120160<br />
120161<br />
120162<br />
120163<br />
120164<br />
120165<br />
120166<br />
QTY<br />
100<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50<br />
100<br />
100<br />
100<br />
100<br />
100<br />
100<br />
50<br />
50
Sheet Metal Screws<br />
• Superior corrosion resistance • Sharp leaded points<br />
• Deep, twist resistance slots • Highest quality<br />
DIA. LENGTH PHILLIPS PHILLIPS PHILLIPS<br />
FLAT PAN OVAL<br />
HEAD QTY HEAD QTY HEAD QTY<br />
#4 1/4 111003 100 107800 100 107814 50<br />
3/8 111004 100<br />
#4<br />
1/2 111005 100 107801 100 107815 50<br />
5/8 111006 100<br />
3/4 111007 100 107802 100 107816 50<br />
1 111008 100 107803 100 107817<br />
#6 1/4 111009 100 09294 107818<br />
3/8 111010 100 09295 50 107819 50<br />
1/2 111011 100 09296 50 09284 50<br />
#6<br />
5/8 111012 100 09297 100<br />
3/4 111013 100 09298 50 09285 50<br />
1 111014 100 107804 50 09286 50<br />
1-1/4 111015 100 107805 50 107820 50<br />
1-1/2 111016 100 107806 50 107821 50<br />
#8 3/8 111017 100 09299 100<br />
1/2 111018 100 09300 50 107822 50<br />
5/8 111019 100 09301 100<br />
3/4 111020 100 09302 50 09287 50<br />
1 111021 100 09303 50 09288 50<br />
#8<br />
1-1/4 111022 100 09304 50 107823 50<br />
1-1/2 111023 100 09305 50 09289 50<br />
1-3/4 111024 100<br />
2 111025 100 09306 25 107824 50<br />
2-1/4 111026 50<br />
2-1/2 111027 50 111057 25<br />
3 111028 50 111058 25<br />
#10 3/8 09307 100<br />
1/2 111029 100 09308 50 107825 50<br />
5/8 111030 100<br />
3/4 111031 100 09309 50 107826 50<br />
1 111032 100 09310 50 09290 50<br />
#10<br />
1-1/4 111033 100 09311 25 09291 25<br />
1-1/2 111034 100 09312 25 09292 25<br />
1-3/4 111035 100 107807 25 107827 25<br />
2 111036 50 09313 25 09293 25<br />
2-1/2 111037 50 111059 25<br />
3 111038 50 111060 25<br />
3-1/2 111039 50<br />
#12 1/2 111040 100 107808 25 107828 25<br />
3/4 111041 100 107809 25 107829 25<br />
1 111042 100 09314 25 107830 25<br />
#12<br />
#14<br />
1-1/4 111043 100 09315 25 107831 25<br />
1-1/2 111044 100 09316 25 107832 25<br />
1-3/4 111045 50<br />
2 111046 50 09317 25 107833 25<br />
2-1/2 111047 50 111061 25<br />
3 111048 50 111062 25<br />
3/4 111049 50 107810 25 107834 25<br />
1 111050 50 107811 25 107835 25<br />
1-1/4 111051 50<br />
1-1/2 111052 50 107812 25 107836 25<br />
1-3/4 111053 25<br />
2 111054 25 107813 25 107837 25<br />
2-1/2 111055 25 111063 25<br />
3 111056 25<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
PHILLIPS<br />
PAN HEAD<br />
PHILLIPS<br />
FLAT HEAD<br />
PHILLIPS<br />
OVAL HEAD<br />
Available in<br />
an Assortment<br />
PART #00713<br />
Found on Page 89<br />
1 800 458-4018 www.uzengprod.com<br />
291<br />
FASTENERS
FASTENERS<br />
292<br />
18-8 Stainless Steel <strong>Fasteners</strong><br />
Threaded Rod<br />
• Tensile strength 85,000 PSI (AVG). • Supplied in 3 foot lengths.<br />
• Superior corrosion resistance. • High abrasion resistance.<br />
• Wide temperature range. • Clean, sharp, rolled threads.<br />
• Will not bend, gall, or freeze. • Non-magnetic.<br />
• Tough and strong - resists, snapping, • Meets ASTM A276/QQS-763.<br />
shearing and stretching.<br />
SIZE PART # QTY.<br />
6-32 USS 140767 1<br />
8-32 USS 140768 1<br />
10-24 USS 140769 1<br />
10-32 SAE 140770 1<br />
1/4-20 USS 09218 1<br />
5/16-18 USS 09219 1<br />
3/8-16 USS 09220 1<br />
1/2-13 USS 09221 1<br />
5/8-11 USS 09222 1<br />
3/4-10 USS 09223 1<br />
1 800 458-4018 www.uzengprod.com
Hex Head Cap Screws<br />
• 18% Chromium, 12% Nickel, 3% molybdenum<br />
• Tensile Strength – Diameters of ¼ thru 5/8 is 120,000 PSI<br />
Diameters of ¾ up to 1” is 95,000 PSI<br />
Diameter of 1” is 80,000 PSI<br />
(After cold worked)<br />
• Best corrosion resistance<br />
LENGTH<br />
1/2<br />
3/4<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
HEX NUT<br />
FLATWASHER<br />
LOCKWASHER<br />
NYLON INSERT<br />
LOCKNUT<br />
EXTRA THICK<br />
FLATWASHER<br />
1/4-20<br />
PART # QTY<br />
147604 50<br />
147605 50<br />
147606 50<br />
147607 50<br />
147608 50<br />
147609 50<br />
147610 50<br />
147611 50<br />
147612 50<br />
147613 50<br />
147614 25<br />
147615 25<br />
147616 25<br />
147617 25<br />
147716 100<br />
147724 100<br />
147732 100<br />
107347 100<br />
123817 50<br />
5/16-18<br />
PART # QTY<br />
147618 50<br />
147619 50<br />
147620 50<br />
147621 50<br />
147622 25<br />
147623 25<br />
147624 25<br />
147625 25<br />
147626 25<br />
147627 25<br />
147628 25<br />
147629 25<br />
147630 25<br />
147631 25<br />
147717 100<br />
147725 100<br />
147733 100<br />
107348 100<br />
123818 50<br />
316 Stainless Steel <strong>Fasteners</strong><br />
3/8-16<br />
PART # QTY<br />
147632 25<br />
147633 25<br />
147634 25<br />
147635 25<br />
147636 25<br />
147637 25<br />
147638 25<br />
147639 25<br />
147640 25<br />
147641 25<br />
147642 25<br />
147643 25<br />
147644 25<br />
147645 25<br />
147718 100<br />
147726 100<br />
147734 100<br />
107349 25<br />
123819 25<br />
7/16-14<br />
PART # QTY<br />
983507 10<br />
983508 10<br />
983509 10<br />
983510 10<br />
983511 10<br />
983512 10<br />
983513 10<br />
983514 10<br />
983515 5<br />
983516 5<br />
983517 5<br />
983518 5<br />
983519 5<br />
983520 5<br />
983521 5<br />
983522 25<br />
983523 50<br />
983524 50<br />
107350 25<br />
123820 25<br />
1/2-13<br />
PART # QTY<br />
147646 25<br />
147647 25<br />
147648 25<br />
147649 25<br />
147650 25<br />
147651 25<br />
147652 25<br />
147653 25<br />
147654 10<br />
147655 10<br />
147656 10<br />
147657 10<br />
147658 10<br />
147659 10<br />
147660 10<br />
147719 50<br />
147727 50<br />
147735 50<br />
107351 25<br />
123821 10<br />
1 800 458-4018 www.uzengprod.com<br />
293<br />
FASTENERS
FASTENERS<br />
294<br />
316 Stainless Steel <strong>Fasteners</strong><br />
Hex Head Cap Screws<br />
LENGTH<br />
1<br />
1-1/4<br />
1-1/2<br />
1-3/4<br />
2<br />
2-1/4<br />
2-1/2<br />
2-3/4<br />
3<br />
3-1/4<br />
3-1/2<br />
3-3/4<br />
4<br />
4-1/2<br />
5<br />
5-1/2<br />
6<br />
HEX NUT<br />
FLATWASHER<br />
LOCKWASHER<br />
NYLON INSERT<br />
LOCKNUT<br />
EXTRA THICK<br />
FLATWASHER<br />
5/8-11<br />
PART # QTY<br />
147661 10<br />
147662 10<br />
147663 10<br />
147664 10<br />
147665 10<br />
147666 10<br />
147667 10<br />
147668 10<br />
147669 10<br />
147670 10<br />
147671 10<br />
147672 10<br />
147673 10<br />
147674 10<br />
147675 10<br />
147676 10<br />
147677 10<br />
147720 50<br />
147728 25<br />
147736 50<br />
107352 10<br />
123822 10<br />
3/4-10<br />
PART # QTY<br />
147678 10<br />
147679 10<br />
147680 10<br />
147681 10<br />
147682 10<br />
147683 10<br />
147684 10<br />
147685 10<br />
147686 10<br />
147687 10<br />
147688 10<br />
147689 10<br />
147690 10<br />
147691 10<br />
147692 10<br />
147693 10<br />
147721 50<br />
147729 25<br />
147737 25<br />
107353 5<br />
123823 5<br />
1 800 458-4018 www.uzengprod.com<br />
7/8-9<br />
PART # QTY<br />
147694 10<br />
147695 10<br />
147696 10<br />
147697 10<br />
147698 10<br />
147699 10<br />
147700 10<br />
147701 10<br />
147702 10<br />
147703 10<br />
147704 10<br />
147705 10<br />
147722 25<br />
147730 25<br />
147738 25<br />
107354 1<br />
123824 5<br />
1-8<br />
PART # QTY<br />
147706 10<br />
147707 10<br />
147708 10<br />
147709 10<br />
147710 10<br />
147711 10<br />
147712 10<br />
147713 10<br />
147714 10<br />
147715 10<br />
147723 25<br />
147731 10<br />
147739 10<br />
107355 1<br />
123825 5
316 S/S Extra Thick Flat Washers<br />
• SAE pattern flat washer<br />
• Thickness is approximately 20% greater than standard SAE pattern<br />
• Thicker washer prevents the dishing of the flat washer<br />
• Extreme corrosion protection<br />
• Composed of 16-18% chromium, 10-14% nickel,<br />
.08% max. carbon, 2-3% molybdenum<br />
• May be slightly magnetic<br />
Flatwashers, Lockwashers and Hex Nuts<br />
• 18% Chromium, 12% Nickel, 3% Molybdenum.<br />
• Best corrosion resistance of all grades.<br />
• Best creep strength at high temperatures.<br />
• Tensile strength up to 170,000 PSI.<br />
Flatwashers Lockwashers<br />
SIZE PART # QTY. SIZE PART # QTY.<br />
1/4 147724 100 1/4 147732 100<br />
5/16 147725 100 5/16 147733 100<br />
3/8 147726 100 3/8 147734 100<br />
1/2 147727 50 1/2 147735 50<br />
5/8 147728 25 5/8 147736 50<br />
3/4 147729 25 3/4 147737 25<br />
7/8 147730 25 7/8 147738 25<br />
1 147731 10 1 147739 10<br />
316 Stainless Steel <strong>Fasteners</strong><br />
PART# SIZE INSIDE DIAMETER OUTSIDE DIAMETER THICKNESS QTY<br />
(MIN-MAX) (MIN-MAX) (MIN-MAX)<br />
123817 1/4 .276-.296 .620-.640 .056-.072 50<br />
123818 5/16 .339-.359 .681-.703 .084-.104 50<br />
123819 3/8 .401-.421 .805-.827 .084-.104 25<br />
123820 7/16 .464-.484 .915-.937 .084-.132 25<br />
123821 1/2 .526-.546 1.055-1.092 .112-.160 10<br />
123822 5/8 .651-.671 1.305-1.342 .140-.177 10<br />
123823 3/4 .807-.827 1.462-1.499 .157-.192 5<br />
123824 7/8 .933-.953 1.743-1.780 .172-.192 5<br />
123825 1 1.057-1.077 1.993-2.030 .172-.192 5<br />
Hex Nuts<br />
SIZE PART # QTY.<br />
1/4-20 147716 100<br />
5/16-18 147717 100<br />
3/8-16 147718 100<br />
1/2-13 147719 50<br />
5/8-11 147720 50<br />
3/4-10 147721 50<br />
7/8-9 147722 25<br />
1-8 147723 25<br />
1 800 458-4018 www.uzengprod.com<br />
Nylon Lock Nuts<br />
SIZE PART # QTY.<br />
1/4” 107347 100<br />
5/16” 107348 100<br />
3/8” 107349 25<br />
7/16” 107350 25<br />
1/2” 107351 25<br />
5/8” 107352 10<br />
3/4” 107353 5<br />
7/8” 107354 1<br />
1” 107355 1<br />
295<br />
FASTENERS
FASTENERS<br />
296<br />
410 Stainless Steel <strong>Fasteners</strong><br />
Thread Cutting Screws Type “F” Point<br />
• Thread cutting screw<br />
DIA. LENGTH PHILLIPS PHILLIPS PHILLIPS<br />
PAN FLAT TRUSS<br />
HEAD QTY HEAD QTY HEAD QTY<br />
4-40<br />
4-40<br />
1/4<br />
3/4<br />
110032 50 110071<br />
110072<br />
25<br />
25<br />
6-32 1/4 111033 50<br />
3/8 110034 50<br />
1/2 110035 50 110073 50 110097 50<br />
6-32<br />
5/8<br />
3/4<br />
110036<br />
110037<br />
50<br />
50<br />
110074<br />
110075<br />
50<br />
50 110098 50<br />
1 110038 50 110076 50 110099 25<br />
1-1/4 110039 10<br />
1-1/2 110040 10 110100 10<br />
8-32 1/4 110041 50 110101 25<br />
3/8 110042 50 110077 50<br />
1/2 110043 50 110078 50 110103 25<br />
5/8 110044 50 110079 50<br />
8-32<br />
3/4<br />
1<br />
110045<br />
110046<br />
50<br />
50<br />
110080<br />
110081<br />
50<br />
50<br />
110105<br />
110106<br />
25<br />
25<br />
1-1/4 110047 50 110082 10<br />
1-1/2 110048 50 110083 20 110107 5<br />
1-3/4 110049 50<br />
2 110084 5<br />
10-24 3/8 110050 50<br />
1/2 110051 50 110108 10<br />
5/8 110052 50<br />
10-24<br />
3/4 110053 50 110085 50 110109 10<br />
1 110054 25 110086 25 110110 10<br />
1-1/4 110055 5 110111 10<br />
1-1/2 110056 5 110087 5 110112 5<br />
1-3/4 110057 5 110088 5<br />
1 800 458-4018 www.uzengprod.com<br />
PHILLIPS<br />
PAN HEAD<br />
PHILLIPS<br />
FLAT HEAD<br />
Available in<br />
an Assortment<br />
PART #00417<br />
Found on Page 90<br />
PART #00418<br />
Found on Page 90
Thread Cutting Screws Type “F” Point<br />
DIA. LENGTH PHILLIPS PHILLIPS PHILLIPS<br />
PAN FLAT TRUSS<br />
HEAD QTY HEAD QTY HEAD QTY<br />
10-32 1/2 110429 50 110437 50 110445 25<br />
5/8 110430 50 110438 50 110446 25<br />
3/4 110431 50 110439 50 110447 25<br />
10-32<br />
1<br />
1-1/4<br />
110432<br />
110433<br />
50<br />
10<br />
110440<br />
110441<br />
25<br />
10<br />
110448 10<br />
1-1/2 110434 5 110442 5 110449 5<br />
1-3/4 110435 5 110443 5 110450 5<br />
2 110436 5 110444 5<br />
12-24 1/2 110058 25 110113 5<br />
3/4 110059 25 110090 10<br />
12-24<br />
1<br />
1-1/4<br />
110060<br />
110061<br />
10<br />
10<br />
110091 10 110113 5<br />
1-1/2 110062 10 110115 5<br />
2 110092 5<br />
1/4-20 1/2 110063 25 110117 5<br />
3/4 110064 25 110093 25 110118 5<br />
1 110065 25 110094 25<br />
1-1/4 110066 5 110095 10<br />
1/4-20 1-1/2 110067 5 110096 10<br />
1-3/4 110068 5<br />
2<br />
2-1/2<br />
110069 5<br />
3 110070 5<br />
410 Stainless Steel <strong>Fasteners</strong><br />
1 800 458-4018 www.uzengprod.com<br />
297<br />
FASTENERS
FASTENERS<br />
298<br />
410 Stainless Steel <strong>Fasteners</strong><br />
410 Stainless Sheet Metal Tek Screws<br />
• Thread cutting screw<br />
DIA. LENGTH HEX PHILLIPS PAN PHILLIPS FLAT<br />
HEAD QTY HEAD QTY HEAD QTY<br />
#6 1/2 109587 100 109620 100 123515 100<br />
3/4 109588 100 109621 100 123516 100<br />
1 109589 100 109622 100 123517 100<br />
1-1/4 109590 50 109623 50 123518 100<br />
1-1/2 109591 50 109624 50 123519 100<br />
#8 1/2 109592 100 109625 100 123520 100<br />
3/4 109593 100 109626 100 123521 100<br />
1 109594 100 109627 100 123522 100<br />
1-1/4 109595 50 109628 50 123523 100<br />
1-1/2 109596 50 109629 50 123524 50<br />
2 109597 25 109630 25 123525 50<br />
#10 1/2 109598 50 109631 50 123526 50<br />
3/4 109599 50 109632 50 123527 50<br />
1 109600 50 109633 50 123528 50<br />
1-1/4 109601 50 109634 50 123529 50<br />
1-1/2 109602 25 109635 25 123530 50<br />
1-3/4 123531 50<br />
2 109603 25 109636 25 123532 25<br />
2-1/2 109604 25 109637 25 123533 25<br />
3 109605 25 109638 25 123534 25<br />
#12 3/4 109606 25 109639 25 123535 50<br />
1 109607 25 109640 25 123536 25<br />
1-1/4 109608 25 109641 25 123537 25<br />
1-1/2 109609 25 109642 25 123538 25<br />
2 109610 25 109643 25 123539 25<br />
2-1/2 109611 10 109644 10 123540 25<br />
3 109612 10 109645 10 123541 10<br />
#14 3/4 109613 25 109646 25 123542 50<br />
1 109614 25 109647 25 123543 50<br />
1-1/4 109615 25 109648 25 123544 25<br />
1-1/2 109616 25 109649 25 123545 25<br />
1-3/4 123546 25<br />
2 109617 10 109650 10 123547 10<br />
2-1/2 109618 10 109651 10 123548 10<br />
3 109619 10 109652 10 123549 10<br />
1 800 458-4018 www.uzengprod.com
Quick Links<br />
• Also known as threaded connectors<br />
• Oval shaped<br />
• Offer a quick and easy way to attach end fittings.<br />
• To close, simply screw the nut onto the threaded end.<br />
• Use with chain of equal or lower working load limit<br />
• Reusable<br />
• Caution: Not for Overhead Lifting. Working Load Limit must not be exceeded.<br />
TRADE SIZE OPENING WORK LOAD<br />
PART # (DIA.) (IN.) LIMIT (LBS.) QTY.<br />
120188 3/16" 1/4" 660 10<br />
120189 1/4" 9/32" 880 10<br />
120190 5/16" 3/8" 1760 10<br />
120191 3/8" 7/16" 2200 10<br />
120192 1/2" 9/16" 3300 5<br />
S Hooks<br />
Applications:<br />
• Fastener used in light duty applications for temporary hanging and connections<br />
• "S" Hooks should be closed after assembly<br />
• NOT TO BE USED FOR OVERHEAD LIFTING<br />
• Low carbon, zinc plated<br />
PART # WIRE DIA. LENGTH APPROX. WORKING LOAD QTY.<br />
122363 .080 1-1/16 30 lbs 50<br />
122364 .093 7/8 30 lbs 50<br />
122365 .105 1-3/32 40 lbs 50<br />
122366 .120 1-5/16 50 lbs 50<br />
122367 .148 2 60 lbs 25<br />
122368 .162 1-7/16 70 lbs 25<br />
122369 .177 2-7/8 85 lbs 25<br />
122370 .188 2-7/8 80 lbs 25<br />
122371 .250 2-1/2 150 lbs 25<br />
122372 .312 2-5/8 300 lbs 10<br />
122373 .375 3-1/4 400 lbs 10<br />
Material Handling<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #00313<br />
Found on Page 91<br />
299<br />
FASTENERS
FASTENERS<br />
300<br />
Material Handling<br />
Roller Chain*<br />
Roller chain consists of links which are held together with riveted pins. Chain size (ANSI No.) is determined<br />
by the pitch, which is the distance between the pin centers (see ”P” on the picture to the right).<br />
• Basic power transmission roller chain measured to ANSI standard<br />
• Single strand<br />
• Made of steel with rivet type construction<br />
• Package quantity - 10 Foot Length<br />
<strong>UZ</strong> ANS PITCH ROLLER ROLLER PIN DIA. (D) AVERAGE<br />
PART NO. NO. (P) DIAMETER WIDTH TENSILE<br />
(R) (W) STRENGTH LBS.<br />
400221 #25 ¼” 0.130” 0.125” 0.091” 990<br />
400222 #35 3/8” 0.200” 0.188” 0.141” 2530<br />
400223 #40 ½” 0.312” 0.313” 0.156” 4290<br />
400224 #41 ½” 0.306” 0.251” 0.141” 2420<br />
400225 #50 5/8” 0.400” 0.375” 0.200” 6930<br />
400226 #60 ¾” 0.469” 0.500” 0.235” 9900<br />
400227 #80 1” 0.625” 0.625” 0.313” 17600<br />
400228 #120 1-1/2” 0.875” 1.000” 0.437” 37400<br />
400229 #140 1-3/4” 1.000” 1.000” 0.500” 48400<br />
400230 #160 2” 1.125” 1.250” 0.563” 60500<br />
*DENOTES NONSTOCK PROGRAM<br />
Roller Chain Links - Two Styles “Connecting” and “Offset”<br />
CONNECTING LINK OFFSET LINK<br />
• Spring clip type for #60 chain and smaller • Slip –fit type<br />
• Cotter pin type furnish for #80 or larger • Also called an “Add-and-Connect” link<br />
• Also called a “Master “ link<br />
ANSI NO. CONNECTING LINK OFFSET LINK <strong>UZ</strong> PART PKG. QTY.<br />
<strong>UZ</strong> PART NO. NO.<br />
#25 400201 400211 10<br />
#35 400202 400212 10<br />
#40 400203 400213 10<br />
#41 400204 400214 10<br />
#50 400205 400215 10<br />
#60 400206 400216 10<br />
#80 400207* 400217* 5<br />
#120 400208* 400218* 1<br />
#140 400231* 400219* 1<br />
#160 400210* 400220* 1<br />
*DENOTES NONSTOCK PROGRAM<br />
1 800 458-4018 www.uzengprod.com<br />
Available in<br />
an Assortment<br />
PART #124294<br />
Found on Page 91
Product<br />
Catalog<br />
Providing Product and Inventory Management<br />
Solutions to Enhance Your World!<br />
World Headquarters<br />
<strong>UZ</strong> <strong>Engineered</strong> <strong>Products</strong><br />
3325 St. Clair Avenue<br />
Cleveland, Ohio 44114<br />
800-458-4018<br />
Fax: 866-802-2739<br />
Canada<br />
145 Adelaide Street South<br />
London, Ontario N5Z 3K7<br />
866-641-5669<br />
Fax: 905-248-3250<br />
2011R05 Part #<strong>UZ</strong>CAT