Fine Finish Spray Gun - Binks Devilbiss Ransburg spray guns

A fine finish spray gun to provide
ultra sensitive fan pattern control
with the comfort of a full-size
spray gun.
The DeVilbiss SRi is the ultimate
fine finish spray gun combined with
the pattern range and versatility
needed for top quality fine finishing
including spot repairs, shading and
stencelling, whilst providing
excellent comfort stability, balance
and delicacy of control.
SRi carry case kits are available
with 2 or 3 guns and a set of
spares and accessories. An optional
gun tray allows up to 4 guns to
be carried around the spray shop
after filling.
Typical Applications in
General Industry
� Fine shading
� Retouching
� Stencilling
� Spot repair
� Reworking
Suitable for these materials
� Solvents and water based
paints
� Stains and varnishes
� Inks and dyes
� Lacquers
Fine Finish Spray Gun
Small scale fine finish spray gun with many practical uses
throughout general industry, ergonomically styled for comfort.
� Superb atomisation of both solvent and waterbased materials
� Ultra lightweight, strong, cast aluminium gun body
� Stainless steel fluid tips & needles
� Choice of HVLP or Trans-tech Compliant air caps
� SRi is supplied as standard with a quality screw top
gravity feed cup (0.125 litre)
� Inexpensive, semi-disposable cups supplied in kits
� Easy to clean, simple to maintain.

SRi Replacement/Spare Parts
Pack of 12 SRi gravity cups & 12 coloured lids (4 Red, 4 Yellow, 4 Green) SRi-478-K12
Pack of 12 pouring funnels SRi-51-K12
No 200 Air Cap (HVLP & Trans-Tech) with retaining ring and friction disc SRi-407-200
No 205 Air Cap (HVLP) with retaining ring and friction disc SRi-407-205
No 210 Air Cap (Compliant) with retaining ring and friction disc SRi-407-210
Service Kit – incl. seal, springs, needle packing SRi-416
Digital Pressure Gauge DGi-501-BAR
Part Numbers: Spot Repair Cased Kits
SRi Spot Repair Case Kit – 2 guns spot repair kit* SRi - 602
SRi Gun Carry Tray to accommodate up to 4 SRi guns for filling SRi - 100
Example of SRi fine finish spray gun part numbering:- SRi-G210-10 means...
SRi-G = SRi Gravity gun with cup / 210 = Air cap / 10 = 1.0mm Fluid tip
DeVilbiss SRi Specification
Air inlet thread: 1 /4” Weight (with cup): 380 grams Cup Capacity: 125mls
DeVilbiss SRi Performance Guide (Air Cap and Fluid Tip Selection)
Above data obtained using a 18 secs DIN 4 material.
Note: No 200 (HVLP/Trans-tech) round spray air cap consumes 65 l/min (2.3 cfm) @1.2 bar (17.4 psi) gun inlet pressure.
No 205 (HVLP) air cap consumes 136 l/min (4.8 cfm) @2.0 bar (29 psi) gun inlet pressure.
No 210 (Trans-tech) air cap consumes 100 l/min (3.6 cfm) @2.0 bar (29 psi) gun inlet pressure.
For further technical information please refer to the SRi Service Bulletin.
ITW Industrial Finishing
Ringwood Road, Bournemouth, England BH11 9LH
Tel: +44 (0)1202 571111
Fax: +44 (0) 1202 573488
Email: industrial.mktg@itwfinishing.co.uk
ITW Oberflächentechnik GmbH & Co. KG
Justus-von-Liebig-Strasse 31,
63128 Dietzenbach Germany
Tel: +49 (0) 6074-403-1
Fax: +49 (0) 6074-403-300
Email: marketing@itw-finishing.de
ITW Surfaces et Finitions
163-171 Avenue des Auréats, BP 1453
26014 Valence cedex FRANCE
Tel: +33(0)4 75 75 27 00
Fax: +33(0)4 75 75 27 59
Email: mkt@itwsf.com
www.itwifeuro.com
*Kit includes SRi Gravity Gun, two
gravity cups, three coloured lids,
pouring funnel, spanner and cleaning
brush. Case kits includes carry tray,
hose, spare cups, funnel, regulator
and accessories.
With 205 (HVLP) Air Cap With 210 (Trans-Tech) Air Cap With 200 (Round spray) Air Cap
(HVLP & Trans-Tech)
Fluid Tip Size Fluid Flow Fan Pattern Fluid Flow Fan Pattern Fluid Flow Fan Pattern
(mm) (gms/min) Size (mm) (gms/min) Size (mm) (gms/min) Size (mm)
0.7 34 120 40 130 30 30
0.8 53 130 61 145 48 30
1.0 67 145 81 160 66 30
1.2 83 160 104 175 81 30
ARB - 04.07