OTTOSEAL S 110 - UKSealants

S 110 The premium neutral silicone
Technical Data Sheet OTTOSEAL® S 110
Page 1 / 5
Index: 30.06.2008
Hermann Otto GmbH · Krankenhausstraße 14 · D-83413 Fridolfing
Tel.: +49-86 84-9 08-0 · Fax: +49-86 84-9 08-539
E-Mail: info@otto-chemie.de · Internet: www.otto-chemie.de
OTTOSEAL ®
S 110
Technical Data Sheet identical with Vitroflex-N ®
Characteristics
Fields of application
Standards and tests
• Neutral-curing RTV-1 silicone sealant
• High abrasion-proof and non streaky according to DIN 18545 Part 2
• Excellent early stressability (green strength)
• Universal adhesion properties
• Tack-free surface
• Good compabitility with paints( yet not paintable)
• Compatible with PVB foils for laminated glass units
• Contains fungicide
• Non-corrosive
• Available in 24 colours ex warehouse
• UV resistant
• Excellent weathering and ageing resistance
• Glazing and sealing applications on wooden windows
• Sealing connection joints on windows and doors made of wood, metal and plastic
• Sealing glass blocks ("Profilit")
• Expansion and connection joints for the construction of prefabricated concrete units
• Sealing facades, parapet elements, roller-blind boxes and metal constructions
• OTTOSEAL ® S 110 is suitable for sealing of glass elements made of laminated and
tempered glass. For further information please contact our technical service department
• Also suitable for connection joints in the bathroom area
• Tested according to DIN 18545, Part 2, group E of Institut für Fenstertechnik e.V.
Rosenheim
• Conforms with the requirements of DIN 18540
• Conforms with the requirements of ISO 11600 25-LM
• Tested according to CTBA L 114 (suitability of sealants for glazing rebate sealing on
wooden windows)

Important information
Technical Data Sheet OTTOSEAL® S 110
Page 2 / 5
Index: 30.06.2008
Due to the multitude of paint systems for wooden windows a general statement regarding
adhesion properties or compatibility is not possible. Individual preliminary tests are required.
A small amount of a splitting product is given off during vulcanization that must not
entrapped by stacking or packing sealed windows/ doors earlier than 24 hours after sealing.
Otherwise there is a risk of a discolouration of the painting.
It is not recommended to overpaint the sealant. OTTOSEAL ® S 110 is compatible with PVB
foils. For laminated glass units with resins please contact our technical service department.
For sealing butt joints between insulating glass units with UV-resistant secondary edge seal
based on silicone (e.g. angled glazing, glass facades etc.) we recommend
OTTOSEAL ® S 7. If the secondary edge sealing is based on another sealant system please
contact our technical service department.
Just apply the sealant in well ventilated rooms, ensure good ventilation during application
and vulcanisation. Please note that smoke from cigarettes or similar substances present in
the surroundings may discolour the sealant.
OTTOSEAL ® S 110 is physiologically harmless and indifferent after curing.
Please refer to our OTTOSEAL ® range for food and drinking water applications.
OTTOSEAL ® S 110 is not suitable for bonding mirrors – use our special adhesive
OTTOSEAL ® S 16.
OTTOSEAL ® S 110 is not suitable for sealing of acrylic glass or polycarbonate twin wall
sheets - use our special silicone OTTOSEAL ® S 72.
Direct contact between the sealant and the following plasticizer emitting materials should be
avoided: butyl rubber, EPDM, neoprene, foam materials, bituminous coatings, etc.
OTTOSEAL ® S 110 must not be used for sealing natural stones like marble, granite, etc. –
use our special sealant OTTOSEAL ® S 70.
If using smoothing agent remove the remaining water streaks on the adjoining surfaces
immediately after sealing. If the surfaces are cleaned at a later date, permanent streaks may
remain.
For underwater applications, e.g. swimming pools, we recommend OTTOSEAL ® S 18.
Please refer to the relevant technical data sheet.
For sealing and bonding of aquaria constructions – use our special silicone
OTTOSEAL ® S 28.
The required vulcanisation time prolongs with increasing thickness of the silicone. One-part
silicones must not be used for bonding applications where the silicone is supposed to be
spread all over the surface. Such applications require a special design – please contact our
technical department. One-part silicones are not designed to be used in layers of more than
15 mm.
Hermann Otto GmbH · Krankenhausstraße 14 · D-83413 Fridolfing
Tel.: +49-86 84-9 08-0 · Fax: +49-86 84-9 08-539
E-Mail: info@otto-chemie.de · Internet: www.otto-chemie.de

Technical properties
Preparation
Priming
Technical Data Sheet OTTOSEAL® S 110
Page 3 / 5
Index: 30.06.2008
Hermann Otto GmbH · Krankenhausstraße 14 · D-83413 Fridolfing
Tel.: +49-86 84-9 08-0 · Fax: +49-86 84-9 08-539
E-Mail: info@otto-chemie.de · Internet: www.otto-chemie.de
Viscosity (23 °C):
Density (23°C, 50 % RH) coloured
non-sag, pasty
approx. 1.16 g/cm 3
Density (23°C, 50 % RH) transparent approx. 1.01 g/cm³
Shore-A hardness (DIN 53505)
coloured:
approx. 25
Shore-A hardness (DIN 53505)
transparent
approx. 20
Tensile elongation (DIN 53504)
coloured:
approx. 650 %
Tensile elongation (DIN 53504) approx. 650 %
transparent
Tensile strength (DIN 53504)
coloured:
approx. 1.5 N/mm 2
Tensile strength (DIN 53504)
approx. 1.5 N/mm²
transparent
Modulus at 100 % elongation
coloured:
approx. 0.4 N/mm 2
Modulus at 100 % elongation approx. 0.4 N/mm²
transparent
Movement capability: 25 %
Temperature resistance: - 40 °C up to + 180 °C
Tooling temperature: + 5 °C up to + 35 °C
Skin-forming time (23°C, 50 % RH): approx. 8 min.
Curing in 24 hours: approx. 2 in 24 h
Shrinkage according to DIN 52 451 - 6 %
Shelf life for cartridge/ sachet (23° C, 12 months from the date of
50 % RH):
Shelf life for pail/ drum (23° C,
50 % RH):
manufacture at room temperature
12 months from the date of
manufacture at room temperature
These data are not intended for use in preparing specifications. Please contact OTTO –
CHEMIE before writing specifications.
The substrates must be clean, free from grease, dry and firm. We recommend OTTO
Cleaner T in order to clean the substrate.
OTTOSEAL ® S 110 exhibits a very adhesion on various substrates without primer. Please
refer to the following primer table where substrates are listed that require priming in order to
obtain adhesion of the silicone rubber:

Primer table
Application
information
Technical Data Sheet OTTOSEAL® S 110
Page 4 / 5
Index: 30.06.2008
Acrylic bathroom
+ / 1101
surfaces (bath tubs)
Acrylic glass
(Makrolon,
Plexiglass, etc.)
OTTOSEAL ® S 72
Aluminium +
Aluminium,
anodized
+
Aluminium powder R / 1101
coated, TGIC-free
Artificial stone/
Precast stone
OTTOSEAL ® S 70
Brass 5 +
Cellular concrete 1215 / 1105
Ceramics, glazed +
Ceramics, unglazed +
Chrome
Concrete
1216
1 Copper
+ or 1215 / 1105
3 +
Fibre reinforced
cement
1215
Glass +
Iron, sand blasted 1216
Lead + / 1216
Melamine
formaldehyd resin 4
R / 1225
+ = good adhesion without primer
- = not suitable
R = further inquiry or preliminary tests required
Hermann Otto GmbH · Krankenhausstraße 14 · D-83413 Fridolfing
Tel.: +49-86 84-9 08-0 · Fax: +49-86 84-9 08-539
E-Mail: info@otto-chemie.de · Internet: www.otto-chemie.de
Natural stone/
Marble
OTTOSEAL ® S 70
Plaster + or 1215 / 1105
Plastic profiles, e.g. + or 1217 / 1227
Vinnolit 2
Polyester +
Polypropylen (PP) -
PVC soft, foils 1217 / 1227
PVC unplasticized + or 1217 / 1227
Stainless steel, rust
proof
+ / 1216
Tinplate 1216
Wood painted
(solvent systems)
+
Wood, painted
(aquaeous systems)
+
Wood, untreated R / 1215 / 1226
Wood varnished
(solvent systems)
+
Wood, varnished
(aquaeous systems)
+
Zinc, galvanised iron +
1 For underwater seals e.g. swimming pools we recommend OTTOSEAL® S 18 and OTTO Primer 1218 on mineralic
surfaces like concrete, tiles, tile adhesive etc. respectively OTTOSEAL® S 70 on natural stones.
2 With OTTOSEAL® S 110 transparent pretreatment with OTTO Primer 1217, on film coated plastics always
pretreatement with OTTO Primer 1217
3 The reaction of OTTOSEAL® S 110 with non-ferrous metals, e.g. chopper, brass, etc. is possible. Curing should not
take place in confined spaces.
4 OTTO Primer 1225 for CPL Laminat from Co. Egger, Resopal from Co. Resopal, Duropal from Co. Pfleiderer,
Homapal from Co. Homapal, Getalit from Co. Westag + Getalit. With all other melamine formaldehyde resins: R.
Please not, that the use of the recommended primer on the mentioned substrates improves the adhesion of the
products.
5 The reaction of OTTOSEAL® S 110 with non-ferrous metals e.g. chopper, brass, etc. is possible. Curing should not
take place in confined spaces.
Provide good ventilation during application and vulcanization of OTTOSEAL ® S 110.
However, because conditions and methodes of use of our products are beyond our control,
customer tests are required to ensure that our products are safe, effective and fully
satisfactory for the intended end use.
Please observe the recommended shelf life that is printed onto the packaging.

Packaging
Colours
Safety precautions
Disposal
Warranty information
Technical Data Sheet OTTOSEAL® S 110
Page 5 / 5
Index: 30.06.2008
Unit Units per box Units per pallet
Cartridges 310 ml 20 1200
Alu-Foil bag 400 ml
20
900
Alu-Foil bag 580 ml
20
600
400 ml alu-foil bags are available upon request with the following colours:
beech, bronze, chestnut, chocolate brown, concrete grey, dark brown, dark grey, fair oak,
mahogany, matt brown, moosgreen, ochre, pine, sand-beige
580 ml alu-foil bags are available upon request with the following colours:
beech, bronze, dark brown, dark grey, fair oak, moosgreen, pine
Hermann Otto GmbH · Krankenhausstraße 14 · D-83413 Fridolfing
Tel.: +49-86 84-9 08-0 · Fax: +49-86 84-9 08-539
E-Mail: info@otto-chemie.de · Internet: www.otto-chemie.de
C76 – beech C83 – dark oak C31 – ochre
C13 – bronze C06 – fair brown C88 – pine
C04 – black C20 – fair-grey C12 – sand-beige
C05 – brown C64 – fair-oak C18 – sanitary-grey
C742 – chestnut C29 – mahagonay C77 – silk grey
C39 – chocolate brown C43 – manhattan C00 – transparent
C56 – concrete grey C1416 – matt brown C01 – white
C49 – dark brown C6005 – moosgreen
C03 – dark grey C57 – oak
The colours black, bronze, dark brown and matt brown are not equipped with fungicide.
Please refer to the material safety data sheet.
Disposal should be made in accordance with federal, state and local regulations.
All information in this publication is based on our current technical knowledge and experiences.
However, because conditions and methods of use of our products are beyond our control, this
information should not be used in substitution for customer’s tests to ensure that Otto-Chemie’s
products are safe, effective and fully satisfactory for the intended end use. Information given in this
technical data sheet and explanations of OTTO-CHEMIE in connection with this technical data sheet
(e.g. service description, reference to DIN regulations etc.) include in case of doubt no acceptance of a
guarantee. Otto-Chemie’s sole warranty is that the product will meet the Otto-Chemie sales
specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is
limited to refund of purchase price or replacement of any product shown to be other than as warranted.
Otto-Chemie specifically disclaims any other express or implied warranty of fitness for a particular
purpose or merchantability, unless Otto-Chemie provides you with a specific, duly signed endorsement
of fitness for use. Otto-Chemie disclaims liability for any incidental or consequential damages.
Suggestions of use shall not be taken as inducements to infringe any patent. All mentioned document
conditions in this technical data sheet lay down the terms of delivery fully and completely. We reserve
the right to alter product constants within the scope of technical progress or new developments. We are
pleased to be at your disposal for inquiries, also regarding specific application problems. If the
application in which the products are used requires governmental approval or clearance, the user is
responsible to obtain such approval. The recommendations do not absolve the user from the obligation
of investigating the possibility of infringement of third parties’ rights and if necessary, clarifying the
position. In the event of deficiency our terms and conditions are applicable. If our terms and conditions
are not with you, we send them to you on request.
Industrieverband
Dichtstoff e e.V.
(IVD)