a2p-power-conv - Amico

Universal Remote
Alarm Buzzer
Features:
M2-REM-AL-WALL
M2-REM-AL-SURF
The Remote Alarm Buzzer can be used in the
following separate functions:
• A device sending a dry contact signal.
• An Amico Alert-2 area or master alarm.
• An Alert-2 manifold bank switch-over occurs.
General Speci� cations:
The Amico Universal Remote Alarm Buzzer will provide the user
with the ability to receive an audible alarm, and a visual alarm
from a remote dry contact signal. If an alarm condition occurs,
the “RED” alarm LED shall � ash and the audible alarm will sound.
Pushing the “ALARM SILENCE” button will cancel the audible
alarm, but the unit will remain in the visual alarm condition
until the problem is recti� ed.
The M2-REM-AL-NEMA includes a built in power supply that
accepts 110 V AC to 240 V AC (50 to 60 Hz) as the input voltage.
The output voltage is 12V DC.
The M2-REM-AL-N2 includes two remote buzzers and a power
supply that accepts 110 V AC to 240V AC (50 to 60 Hz) as the
input voltage and an output voltage of 12V DC.
The M2-REM-AL-WALL and M2-REM-AL-SURF if used with an
Amico Alert-2 Manifold or Alarm does not require a power
supply if the distance between the Universal Remote Buzzer
and the Manifold or Alarm is less than 60 ft. If the distance is
greater than 60 ft, an external power supply (A2P-POWER-CONV)
or a 12 volt DC voltage is required.
M2-REM-AL-NEMA
M2-REM-AL-N2
1

Technical Speci� cations
M2-REM-AL-WALL
5
[127]
3
[76.2]
5.5
[139.7]
M2-REM-AL-SURF
4-7/16
[127]
M2-REM-AL-NEMA
6
[152.4]
6
[152.4]
M2-REM-AL-N2
8
[203.2]
2
[51]
2-7/8
[73]
4
[101.6]
4
[101]
6
[152.4]
4
[101.6]
wiring schematic
AC �� ������ Supply
��� 120 ��� VAC
Optional Power Supply Power
Supply
12V DC
+ -
Optional Signal
Device
Dry Contact
C NO NC
+ - C NO NC
Amico Corporation 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada I 71 East Industry Court, Deer Park , NY 11729, USA
Toll Free Tel: 1.877.462.6426 | Toll Free Fax:1.866.440.4986 Tel: 905.764.0800 | Fax: 905.764.0862
APE-SP-UNIVALMBUZZR PRINTED APR 09
www.amico.com
REMOTE BUZZER
+
S
-
annunciator wiring
schematic
��������� Optional: �� To Amico ����� Universal ���������
Remote Buzzer
������ ������
REMOTE BUZZER
+12V
NO NC COM GND +12V
Power Supply: A2P-POWER-CONV
NOTE: Power supply not included with wall & surface mount
wiring schematic
AC Supply
G G N L
Power Supply
Power Supply
Optional Dry Contact Signal
Device
12V DC
+ -
C NO NC
R1 �� R2 ��
REMOTE BUZZER
+
- S
G R2 R1
G R2 R1
Optional Signal
Device
Dry Contact
REMOTE BUZZER
+
S
-
REMOTE BUZZER
+ -
+
S
-
+ -
Power Supply
12V DC
AC �� ������ Supply
��� 120 ��� VAC
Inch
[mm]
+
S
-
annunciator wiring
schematic
Optional: ��������� To Amico �� ����� Universal ���������
Remote ������ Buzzer������
Power Supply
12V DC
+ -
+ -
NO NC COM GND +12V
+12V
REMOTE BUZZER
NOTE: The Manifold can be
connected from Normally
Open to R1 or R2, but all
appropriate connections
(Common) should be
made to Ground.
+
S
-
2