RSP Series

EAL Series Area Luminaire Type: Job:
A B C D
14.9” 19.4” 11.0” 5.0”
(37.85cm) (49.28cm) (27.94cm) (12.70cm)
70-175 Watt HID and CF unit - 13” Housing
A B C D
11.3” 13.3” 7.0” 4.0”
(28.70cm) (33.78cm) (17.78cm) (10.16cm)
A B C
23.0” 19.4” 32.0”
(58.42cm) (49.28cm) (81.28cm)
70-175 Watt HID and CF unit - 13” Housing
applications
Architectural
Site Lighting
Parking Lots
Plazas
Walkways
Recreational
Areas
EAL “S” Arm Mount Surface Arm Mount to Square Pole
A
200-1000 Watt HID and QL unit - 19” Housing
EAL Post Top Mount
A
B C
200-1000 Watt HID and QL unit - 19” Housing
A B C
16.0” 13.3” 21.0”
(40.64cm) (33.78cm) (53.34cm)
42 Specifications and dimensions are subject to change without notice.
B
D
C
Catalog Number:
- - - -
-
SERIES DISTRIBUTION VOLTAGE MOUNTING OPTIONS FINISH
EPA (Effective Projected Area in Ft 2)
Post Top Mount
For Architectural Outdoor options, finish choices and accessories, see pages 72 - 76.
200- 200-1000W 70-
1000W w / Vertical F optics 175W
Head Directed Down 2.1 3.0 1.0
Head Directed at 45° 2.5 3.3 1.4
and 135° from nadir
ACCESSORIES
Specifications
Housing
Die-cast housing shall be of low copper (less than 0.4%) marine grade aluminum alloy. Housing
shall be Dust-Tite TM and totally sealed from particulate entry. Housing shall not incorporate
weep holes, filters, wicks or any route for direct exchange with outside air. Standard unit
constructed to IP65.
Optical Module
Reflectors shall be multi-faceted segmented and made of high purity,anodized aluminum.
Segmented reflectors for 200-1000W HID and QL units shall be of “Super Sheet” aluminum
with an inorganic dielectric coating, producing a minimum reflectivity of 94% for optimum
efficiency. Optical assemblies shall be field-rotatable and exchangeable. Optics are available
to meet IES definitions of Full Cutoff, Cutoff, and Semi-Cutoff.
Lamp Access
Custom shaped silicon gasketed lens door shall be secured by four captive screws and hinges
that open for lamp access. Mechanical stops in the housing shall ensure proper compression
of gasket and relamping.
Lens
Lens shall be tempered glass to withstand thermal and physical shock.
Socket
HID sockets shall be porcelain, grip-type, mogul base (medium base for 175W and below),
4KV (5KV for 1000W HPS) pulse-rated for 70 through 1000 watts. Lamp and lamp holder are
pre-assembled and are integral in QL induction lamp units. CF units use GX24q-4 sockets.
Ballast
HID Units: Ballast shall be high power factor with reliable starting down to -29°C (-20°F) for
MH, -34°C (-30°F) for Pulse Start MH, and -40°C (-40°F) for HPS. Crest factor does not exceed
1.8. Ballast has Class H, 180°C (356°F) rated insulation. CF and QL Units: Ballast shall be
electronic, high frequency, high power factor with reliable starting down to -30°C (-22°F) for
QL units, and down to -18°C (0°F) for CF units, with THD of