The Centre of Excellence for Sheet - EMW Eisen- und Metallhandel ...

The Centre of Excellence for Sheet – 

Grade variety keeps us ahead 

Catalogue 

2011 

1

Sheet from EMW. 

Steel is our mission 

Since 1952, EMW has developed into one of 

the most modern and most efficient service 

centres sheet in Europe. With our strategy 

of offering customers top-class quality and 

intelligent steel service solutions tailored 

to individual application requirements, the 

company has been successful on the steel 

market for over 5 decades. 

As one of the industry’s largest steel service 

centres, EMW is a supplier of coils, slit strips 

and cut-to-size sheets. Our highly efficient 

machines, consisting of modern slitting 

lines, longitudinal and lateral slitting lines 

and cutting centres guarantee fast and 

flexible deliveries. 

I. 

II. 

III. 

IV. 

V. 

VI. 

Product range 4 

Consulting 6 

Grade variety 8 

Delivery service 10 

Quality 12 

Perforated metal 14 

Our market-oriented product range is 

therefore supplemented by a high level of 

customer-oriented service, ranging from 

competent advice and quality control right 

up to logistics. 

VII. 

VIII. Cold-rolled sheet 19 

IX. 

X. 

XI. 

Hot-rolled sheet 16 

Electrolytically galvanized sheet 22 

Hot-dip galvanized sheet 26 

Contacts 31 

3

4 

I.


A product range of exceptional quality 

Coils 

EMW has over 100,000 t of input material in 

stock in an area measuring 32,000 m2 . Almost 

all standard market grades are constantly 

available for delivery; mainly hot-dip and 

electrolytically galvanized, warm and coldrolled, 

hot-dip aluminised and plastic coated. 

High-quality automobile grades, hightensile 

steels and grades for enamelling are 

particular EMW specialities. All are available 

in widths of up to 1,850 mm, thicknesses up 

to 4.50 mm and coil weights of up to 32 t. 

This extensive assortment and the vast 

storage capacity are benefits our customers 

profit from. 

Slit strip 

As a matter of tradition, EMW operations are 

based on the latest production technology 

and the highest quality standards. On its 

state-of-the-art facilities, EMW produces slit 

strips and trimmed wide strips in various 

Hot-rolled 

Cold-rolled 

Electrolytically galvanized 

Hot-dip galvanized 

Hot-dip aluminised 

finishes and in first-class quality. The finest 

tolerances, cleanly cut edges and extremely 

smooth surfaces make EMW slit strips 

extremely easy to use. The strips are loaded 

according to your specifications, flat or 

upright for subsequent handling by crane 

or fork-lift truck. Here, too, EMW shows its 

flexibility. 

Cut-to-size blanks/sheet 

Cut-to size blanks and sheets are another 

of EMW’s specialist areas, with a delivery 

range covering thicknesses from 0.40 mm, 

widths of up to 1,850 mm and lengths up 

to 8,000 mm. Advanced cutting centres cut 

blanks of various surface finishes from coils 

or sheets with precision and reliability. 

CNC controlled facilities guarantee maximum 

efficiency and accuracy, ensuring 

each cut will be as precise as the one before. 

EMW can supply any dimension in the 

specified grades in the shortest possible 

delivery time. One of our great strengths 

is the delivery of large quantities to set 

deadlines. EMW can deliver most steel 

sheet formats required by industry straight 

from stock. Apart from the usual stock 

sizes, EWM also has a great number of 

different ready-made blanks ranging from 

0.40 - 3.00 mm in thickness, and in all 

grades. Alternatively, EMW can tell you the 

coil widths available and you can specify 

the sheet lengths. 

Processing service 

Coil-to-coil and sheet perforation is an 

integral part of the service we offer, along 

with the laser cutting, bending, notching, 

punching, degreasing, powder coating, 

lacquering and anodising of steel sheet. 

Here, the main focus is placed on 

providing the best possible quality of 

service based on our extensive expertise 

and modern manufacturing machines. 

5

6 

II.


Personal consulting service guarantees 

cost benefits 

EMW attaches great importance to the 

professional consulting and continuous 

after-sales service it provides for its 

customers. After all, long-term partnerships 

are most easily built up with satisfied 

customers. 

At EMW, consulting begins of course with 

competent information on the telephone 

but goes much further. In both, the product 

planning and production phases, experts 

are on hand to offer advice and assistance. 

The advice you get from EMW focuses 

exclusively on solutions geared specifically 

to your individual requirements. Take us at 

our word. 

We can show you how to reduce your 

stock-keeping costs by using EMW as your 

“upstream warehouse”. Having no storage 

capacity on stand-by releases, capital tied 

up unnecessarily. In addition, our extensive 

storage capacity of around 32,000 m² 

means we can take advantage of spot 

market opportunities worldwide. 

This enables us to provide you with highgrade 

material at competitive market prices. 

Why not put us to the test? 

At EMW, we can offer our customers clear 

cost benefits, guaranteed by an extensive 

range of services. We not only provide 

innovative solutions, but also aim to achieve 

long-term, reliable partnerships. 

7

8 

III.


Experience in worldwide procurement logistics 

EMW can supply the entire spectrum of 

steel grades at favourable conditions. 

Though the great majority of the material 

we have in stock is bought from leading 

European steel manufacturers, EMW also 

takes every opportunity worldwide to 

obtain high-grade materials – making use 

of our extensive know-how and over five 

decades of experience in purchasing steel. 

EMW delivery range 

� Hot-rolled sheet 

� Cold-rolled sheet 

� Hot-dip galvanized sheet 

� Electrolytically galvanized / 

organic-coated sheet 

(Granocoat) 

� Hot-dip aluminised sheet 

9

10 

IV.


Speed gives us our competitive edge 

Customer-orientated service is the principle 

on which EMW bases its operations and 

naturally includes a comprehensive delivery 

service as one essential component. When 

it comes to storage capacity, speed and 

flexibility, EMW is totally reliable. You specify 

material, amount and date, and we take 

care of the rest. 

For our experienced team, professional 

supply chain management and just-in-time 

delivery are all in a day’s work. 

On top of this, EMW’s outstanding reaction 

times provide us with a clear competitive 

advantage in the world market place. The 

extensive range of grades available enables 

EMW to react especially quickly to tight 

delivery deadlines and requests for alterations. 

That is principle behind our success. 

11

12 

V.


No compromise on quality 

We regard our customers as partners with 

whom we want to operate successfully in 

the marketplace. The entire EMW organisation 

is characterised by the direct orientation 

towards customers, their needs 

and expectations. And that’s why our 

continuous, documented quality assurance 

system is an indispensable component of 

our business operation. 

Reliability guaranteed 

Quality assurance is given the highest 

priority at EMW, because the consistent 

quality of the input material is the key to 

guaranteeing trouble-free processing of our 

products by our customers. 

For this reason, EMW has its own testing 

laboratory with state-of-the-art technology, 

such as tensile testing machines and spectral 

analysis equipment. 

Here both, the material and processing 

quality are continuously examined and 

documented. 

To ensure we can meet our customers’ 

increased demands regarding quality, we 

have had our quality management 

certified according to TS 16949. 

13

14 

VI.


Perforated metal made to measure – 

individual and fast 

The application potential of perforated metal 

is unlimited and no doubt a major factor 

behind the unbroken success this material has 

experienced over recent decades. SCHÄFER 

Perforated Metal meets the highest standards 

of quality. 

Just ask the experts: SCHÄFER will be glad to 

offer any advice you need: +49 (0) 2735/787-05 

www.schaefer-lochbleche.de 

Perforated metal from SCHÄFER. 

Precision in Steel. 

Perforated metal – when it comes to combing 

countless different demands of function and 

design in such a fascinating way, there’s no 

other material quite like it. Perforated metal 

can now be found in almost all walks of 

everyday life. The possibilities are boundless 

and they are growing day by day. 

And so are the demands the processing industry 

is placing on this fashionable material. The 

name “SCHÄFER Perforated Metal” has been 

synonymous with professionalism, perfection 

and precision for many years. Storage 

capacity, service range and delivery service 

are second to none. The experts from 

Neunkirchen set standards in market and 

customer orientation and show precisely 

what is meant by expertise in this field 

through the wide range of different services 

on offer. The customer specifies the material, 

the perforation pattern and the dimensions – 

SCHÄFER does the rest: coil-to-coil perforation, 

sheets or cut-to-size sheets to precise 

customer specifications, extensive stocks 

covering many standard formats, materials 

and perforation patterns. 

Apart from our speedy delivery service, the 

fact that we offer a full range processing 

service also makes us a greatly appreciated 

business partner: whether notching, bending, 

punching, laser cutting, welding, galvanising, 

degreasing or powder coating – on request 

SCHÄFER can take on the precise processing 

of the material you order. 

15

16 

VII. Hot-rolled sheet 

Lieferprogramm EMW delivery range der EMW Coils Spaltband Slit strip Formate Cut-to-size / Zuschnitte sheet 

Dicken Thicknesses ab from 1,00 1.00 – 4,00 – 4.50 mm mm ab from 1,00 1.00 – 4,50 – 4.50 mm mm from ab 1,00 1.00 – – 3,00 3.00 mm 

Breiten Widths bis up to 1.850 1,850 mm mm bis up to 1.850 1,850 mm mm up bis to 1.530 1,530 mm bis up to 1.850 1,850 mm mm 

Lengths Längen --- --- --- up bis to 8,000 8.000 mm up bis to 3.000 3,000 mm mm 

Tolerances Toleranzen Tolerances Toleranzen for für strips Bänder and und sheets: Bleche: DIN DIN EN EN 10051. Finer Engere tolerances Toleranzen and special und besondere edge formation Kantenausbildung available by nach arrangement. Absprache 

Mild grades – continuously hot-rolled strip and sheet of mild steels for cold forming acc. to DIN EN 10111 : 2008 

Steel grade/type Melt analysis chem. composition Mechanical properties (lat.) 

1) 

ReL R m Min. fracture elongation 

L O = 80 mm L O = 5.65 √S O 

C Mn P S 1.0 mm ≤ e 2.0 mm ≤ e 1.0 mm ≤ e 1.5 mm ≤ e 2.0 mm ≤ e 3.0 mm ≤ e 

e < 2.0 mm e < 4.5 mm max. e < 1.5 mm e < 2.0 mm e < 3.0 mm e < 4.5 mm 

Code Material no. max. % max. % max. % max. % N/mm 2 N/mm 2 N/mm 2 % % % % 

DD11 1.0332 0.12 0.60 0.045 0.045 170 – 360 170 – 340 440 22 23 24 28 

DD12 1.0398 0.10 0.45 0.035 0.035 170 – 340 170 – 320 420 24 25 26 30 

DD13 1.0335 0.08 0.40 0.030 0.030 170 – 330 170 – 310 400 27 28 29 33 

DD14 1.0389 0.08 0.35 0.025 0.025 170 – 310 170 – 290 380 30 31 32 36 

1) If the product has no pronounced yield point, Rp0.2 must be used instead of R eL. 

Microalloyed grades – hot-rolled flat products of steels with high yield point for cold forming acc. to DIN EN 10149 : 1995 

Mechanical properties of thermo-mechanically rolled steels (long.) 

Steel grade/type Upper yield point Tensile strength Fracture elongation, A 1) 

1) 

ReH 1) 

Rm % min. 

N/mm 2 min N/mm 2 nominal thickness in mm 

< 3 ≥ 3 

Code Material no. L O = 80 mm L O = 5.65 √S O 

S315MC 1.0972 315 390 – 510 20 24 

S355MC 1.0976 355 430 – 550 19 23 

S420MC 1.0980 420 480 – 620 16 19 

S460MC 1.0982 460 520 – 670 14 17 

S500MC 1.0984 500 550 – 700 12 14 

S550MC 1.0986 550 600 – 760 12 14 

S600MC 1.8969 600 650 – 820 11 13 

S650MC 1.8976 650 700 – 880 10 12 

S700MC 1.8974 700 750 – 950 10 12 

Chemical composition/melt analysis) of thermo-mechanically rolled steels 

Steel grade/type C Mn Si P S Altotal Nb V Ti Mo B 

% % % % % % % % % % % 

Code Material no. max. max. max. max. max. min. max. 2) 

max. 2) 

max. 2) 

max. max. 

S315MC 1.0972 0.12 1.30 0.50 0.025 0.020 0.015 0.09 0.20 0.15 – – 

S355MC 1.0976 0.12 1.50 0.50 0.025 0.020 0.015 0.09 0.20 0.15 – – 

S420MC 1.0980 0.12 1.60 0.50 0.025 0.015 0.015 0.09 0.20 0.15 – – 

S460MC 1.0982 0.12 1.60 0.50 0.025 0.015 0.015 0.09 0.20 0.15 – – 

S500MC 1.0984 0.12 1.70 0.50 0.025 0.015 0.015 0.09 0.20 0.15 – – 

S550MC 1.0986 0.12 1.80 0.50 0.025 0.015 0.015 0.09 0.20 0.15 – – 

S600MC 1.8969 0.12 1.90 0.50 0.025 0.015 0.015 0.09 0.20 0.22 0.50 0.005 

S650MC 1.8976 0.12 2.00 0.60 0.025 0.015 0.015 0.09 0.20 0.22 0.50 0.005 

S700MC 1.8974 0.12 2.10 0.60 0.025 0.015 0.015 0.09 0.20 0.22 0.50 0.005 

1) The values for the tensile test are those determined for longitudinal samples. 

2) The sum of Nb, V and Ti must not exceed 0.22 %.


Lieferprogramm EMW delivery range der EMW Coils Spaltband Slit strip Formate Cut-to-size / Zuschnitte sheet 

Dicken Thicknesses ab from 1,00 1.00 – 4,00 – 4.50 mm mm ab from 1,00 1.00 – 4,50 – 4.50 mm mm from ab 1,00 1.00 – – 3,00 3.00 mm 

Breiten Widths bis up to 1.850 1,850 mm mm bis up to 1.850 1,850 mm mm up bis to 1.530 1,530 mm bis up to 1.850 1,850 mm mm 

Lengths Längen --- --- --- up bis to 8,000 8.000 mm up bis to 3.000 3,000 mm mm 

Tolerances Toleranzen Tolerances Toleranzen for für strips Bänder and und sheets: Bleche: DIN DIN EN EN 10051. Finer Engere tolerances Toleranzen and special und besondere edge formation Kantenausbildung available by nach arrangement. Absprache 

Construction steels – hot-rolled products of unalloyed construction steels with values for notch impact strength acc. to DIN EN 10025 : 2004 

Mechanical properties 

Steel grade/type Minimum yield 1) Tensile strength Rm 1) 

Min. fracture elongation 

1) point Reh N/mm2 Sample LO = 80 mm LO = 5.65 √SO N/mm2 nominal thickness mm position1) nominal thickness mm nominal 

Nominal thickness mm 

thickness mm 

> 1 > 1.5 > 2 > 2.5 ≥ 3 

Code 

S235JR 

Material no. 

1.0038 

≤ 4 

235 

< 3 

360 – 510 

≥ 3 – ≤ 4 

360 – 510 l 

≤ 1 

17 

≤ 1.5 

18 

≤ 2 

19 

≤ 2.5 

20 

< 3 

21 

≤ 4 

26 

S235J0 1.0114 235 360 – 510 360 – 510 

S235J2 1.0117 235 360 – 510 360 – 510 t 15 16 17 18 19 24 

S275JR 1.0044 275 430 – 580 410 – 560 l 15 16 17 18 19 23 

S275J0 1.0143 275 430 – 580 410 – 560 

S275J2 1.0145 275 430 – 580 410 – 560 t 13 14 15 16 17 21 

S355JR 1.0045 355 510 – 680 470 – 630 l 14 15 16 17 18 22 

S355J0 1.0553 355 510 – 680 470 – 630 

S355J2 1.0577 355 510 – 680 470 – 630 

S355K2 1.0596 355 510 – 680 470 – 630 t 12 13 14 15 16 20 

S450J0 1.0590 450 – 550 – 720 l – – – – – 17 

Chemical composition after melt analysis for flat and long products made of steel types with values for notch impact strength 

Steel grade/type C Si Mn P S N Cu 

max. % max. % max. % max. % max. % max. % max. % 

Code Material no. 

S235JR 1.0038 0.17 – 1.40 0.035 0.035 0.012 0.55 

S235J0 1.0114 0.17 – 1.40 0.030 0.030 0.012 0.55 

S235J2 1.0117 0.17 – 1.40 0.025 0.025 – 0.55 

S275JR 1.0044 0.21 – 1.50 0.035 0.035 0.012 0.55 

S275J0 1.0143 0.18 – 1.50 0.030 0.030 0.012 0.55 

S275J2 1.0145 0.18 – 1.50 0.025 0.025 – 0.55 

S355JR 1.0045 0.24 0.55 1.60 0.035 0.035 0.012 0.55 

S355J0 1.0553 0.20 0.55 1.60 0.030 0.030 0.012 0.55 

S355J2 1.0577 0.20 0.55 1.60 0.025 0.025 – 0.55 

S355K2 1.0596 0.20 0.55 1.60 0.025 0.025 – 0.55 

S450J0 1.0590 0.20 0.55 1.70 0.030 0.030 0.025 0.55 

1) For sheet, strip and wide flats in widths < 600 mm, the direction lateral (t) means transverse to roller direction. For all other products, the values are for roller direction (I). 

17

18 


EMW delivery range Coils Slit strip Cut-to-size sheet 

Thicknesses from 1.00 – 4.50 mm from 1.00 – 4.50 mm from 1.00 – 3.00 mm 

Widths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm 

Lengths --- --- up to 8,000 mm up to 3,000 mm 

Tolerances Tolerances for strips and sheets: DIN EN 10051. Finer tolerances and special edge formation available by arrangement. 

Construction steels – hot-rolled products of unalloyed construction steels without values for notch impact strength acc. to DIN EN 10025 : 2004 


Steel grade / type Minimum 1) Tensile strength Rm 1) 

Min. fracture elongation 

yield Sample LO = 80 mm LO point R 1) 

eh position1) = 5.65 √SO Nominal Nominal thickness Nominal thickness 

thickness 

mm 

mm mm 

Code Material no. 

≤ 4 

N/mm 

< 3 ≥ 3 – ≤ 4 

≤ 1 

> 1 > 1.5 > 2 > 2.5 ≥ 3 P S N 

2 N/mm2 N/mm2 ≤ 1.5 ≤ 2 ≤ 2.5 ≤ 3 ≤ 4.5 % max. % max. % max. 

S185 1.0035 185 310 – 540 290 – 510 

l 

t 

10 

8 

11 

9 

12 

10 

13 

11 

14 

12 

18 

16 

– – – 

E295 1.0050 295 490 – 660 470 – 610 

l 

t 

12 

10 

13 

11 

14 

12 

15 

13 

16 

14 

20 

18 

0.045 0.045 0.012 

E335 1.0060 335 590 – 770 570 – 710 

l 

t 

8 

6 

9 

7 

10 

8 

11 

9 

12 

10 

16 

14 

0.045 0.045 0.012 

E360 1.0070 360 690 – 900 670 – 830 

l 

t 

4 

3 

5 

4 

6 

5 

7 

6 

8 

7 

11 

10 

0.045 0.045 0.012 

1) For sheet, strip and wide flats in widths > 600 mm, the direction lateral (t) means transverse to roller direction. For all other products, the values are for roller direction (I). 


Steel grade/type Elongation limit Tensile strength Fracture elongation Work hardening exponent Bake hardening index 

Rp0.2 N/mm2 min Rm N/mm2 min A80 % min N10-UE min BH2 MPa1) Multiphase steels – hot-rolled products made of multiphase steels for cold forming acc. to prEN 10336 : 2007 (draft) 

min 

Code 

FB-steels 

Material no. 

HDT450F 1.0961 320 – 420 450 23 – 30 

HDT560F 

DP-steels 

1.0959 460 – 570 560 16 – 30 

HDT580X 

CP-steels 

1.0936 330 – 460 580 19 0.13 30 

HDT750C 1.0956 620 – 760 750 10 – 30 

HDT780C 1.0957 680 – 830 780 10 – 30 

HDT950C 

MS-steels 

1.0958 720 – 920 950 9 – 30 

HDT1200M 1.0965 900 – 1150 1200 5 – 30 

Chemical properties 

Steel grade/type Percentage by mass % 

Code 

FB-steels 

Material no. 

C 

max. 

Si 

max. 

Mn 

max. 

P 

max. 

S 

max. 

Altotal Cr + Mo 

max. 

Nb + Ti 

max. 

V 

max. 

B 

max. 

HDT450F 1.0961 0.18 0.50 1.20 0.030 0.010 ≥ 0.015 0.30 0.05 0.15 0.005 

HDT560F 

DP-steels 

1.0959 0.18 0.50 1.80 0.025 0.010 ≥ 0.015 0.30 0.15 0.15 0.005 

HDT580X 

CP-steels 

1.0936 0.17 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT750C 1.0956 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT780C 1.0957 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT950C 

MS-steels 

1.0958 0.23 0.80 2.20 0.080 0.015 ≤ 2.00 1.20 0.15 0.20 0.005 

HDT1200M 1.0965 0.25 0.80 2.00 0.060 0.015 ≤ 2.00 1.20 0.15 0.22 0.005

VIII. Cold-rolled sheet 





Tolerances Acc. to DIN EN 10131; finer tolerances available by arrangement. 

Mild grades – cold-rolled flat products of mild steels for cold forming DIN EN 10130 : 2006 

Mechanical properties (lat.) 

Steel grade/type R e 1) R m A 80 2) r90 3) 4) n90 3) Melt analysis 

chemical composition 

C P S Mn Ti 

Code Material no. N/mm 2 N/mm 2 min. % min. min. max. % max. % max. % max. % max. % 

DC01 1.0330 –/280 270 – 410 28 – – 0.12 0.045 0.045 0.60 – 

DC03 1.0347 –/240 270 – 370 34 1.3 – 0.10 0.035 0.035 0.45 – 

DC04 1.0338 –/210 270 – 350 38 1.6 0.180 0.08 0.030 0.030 0.40 – 

DC05 1.0312 –/180 270 – 330 40 1.9 0.200 0.06 0.025 0.025 0.35 – 

DC06 1.0873 –/170 270 – 330 41 2.1 0.220 0.02 0.020 0.020 0.25 0.3 

DC07 1.0898 –/150 250 – 310 44 2.5 0.230 0.01 0.020 0.020 0.20 0.2 

1) For products with no clear yield point, the values for the 0.2 % elongation limit (Rp0.2), are taken as those for the yield point. For other products, those for the lower yield point (ReL) apply. 

For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a 20 MPa higher maximum yield point value is permissible. For thicknesses ≤ 0.50 mm, a higher maximum yield point value of 40 MPa is permissible. 

2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, the minimum values for fracture elongation are reduced by 2 units, for thicknesses of ≤ 0.50 mm by 4 units. 

3) The r90- and n90- values only apply for product thicknesses of > 0.50 mm. 

4) For thickness > 2 mm, the r90-value is reduced by 0.2. 


Steel grade/type Re Rm 2) A80 3) r Chemical composition 

(Melt analysis) 

N/mm2 1) N/mm2 min. min. C Ti 

Code Material no. max. 

DC01EK 1.0390 270 270 – 390 30 – 0.08 – 

DC04EK 1.0392 220 6) 270 – 350 36 – 0.08 – 

DC06EK 1.0869 190 270 – 350 38 1.6 0.02 0.30 

DC03ED 1.0399 240 270 – 370 34 – 5) – 

DC04ED 1.0394 210 4) Enamelling grades – -rolled flat products of mild steels for enamelling acc. to DIN EN 10209 : 1996 

270 – 350 38 – 5) – 

DC06ED 1.0872 190 270 – 350 38 1.6 0.02 0.30 

1) If the yield point is not pronounced, the values apply for the 0.2 % elongation limit (Rp0,2), If pronounced, the values apply to the lower yield point (ReL) apply. 

For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a minimum value for fracture elongation of 2 units lower is permissible, and of 4 units lower for thicknesses ≤ 0.50 mm. 

2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a minimum value for fracture elongation of 2 units lower is permissible, and of 4 units lower for thicknesses ≤ 0.50 mm. 

3) The r-values only apply for product thicknesses > 0.50 mm. For thicknesses > 2 mm, the r-value is reduced by 0.2. 

4) For thicknesses > 0.50 mm, the yield point may only reach a maximum of 225 N/mm². 

5) The steel grades DC03ED and DC04ED are usually decarburized in the solid phase. After decarburization, analysis must only show a maximum carbon content of 0.004 %. 

6) If specified by the customer, steel grade DC04EK can be supplied in thicknesses of 0.7 mm to 1.5 mm with Re < 210 N/mm² and A80 > 38 %. It then remains for the manufacturer to select the surface 

roughness values for a dull matt finish. 

19

20 



Thicknesses ab 0.30 – 3.00 mm ab 0.30 – 3.00 mm ab 0.40 – 3.00 mm 

Widths bis 1,850 mm bis 1,850 mm bis 1,530 mm bis 1,850 mm 

Lengths --- --- bis 8,000 mm bis 3,000 mm 


Microalloyed grades – cold-rolled flat products with high yield point for cold forming made of microalloyed steels DIN EN 10268 : 2006 


Steel grade/type 0.2 % Higher yield Tensile strength Fracture Vertical Vertical Work hardening 

Elongation limit 1) point through elongation 3) anisotropy anisotropy 2) 3) 4) exponent 4) 

heat 

treatment 2) 

R p0,2 1) BH 2 R m A 80 r r n 

Code Material no. N/mm 2 N/mm 2 N/mm 2 min. quer % max. quer min. quer min quer 

HC180Y 1.0922 180 – 230 340 – 400 36 1.7 0.19 

HC180P 1.0342 180 – 230 280 – 360 34 1.6 0.17 

HC180B 1.0395 180 – 230 35 300 – 360 34 1.6 0.17 

HC220Y 1.0925 220 – 270 350 – 420 34 1.6 0.18 

HC220I 1.0346 220 – 270 300 – 380 34 1.4 0.18 

HC220P 1.0397 220 – 270 320 – 400 32 1.3 0.16 

HC220B 1.0396 220 – 270 35 320 – 400 32 1.5 0.16 

HC260Y 1.0928 260 – 320 380 – 440 32 1.4 0.17 

HC260I 1.0349 260 – 310 320 – 400 32 1.4 0.17 

HC260P 1.0417 260 – 320 360 – 440 29 

HC260B 1.0400 260 – 320 35 360 – 440 29 

HC260LA 1.0480 260 – 330 350 – 430 26 

HC300I 1.0447 300 – 350 340 – 440 30 1.4 0.16 

HC300P 1.0448 300 – 360 400 – 480 26 

HC300B 1.0444 300 – 360 35 400 – 480 26 

HC300LA 1.0489 300 – 380 380 – 480 23 

HC340LA 1.0548 340 – 420 410 – 510 21 

HC380LA 1.0550 380 – 480 440 – 560 19 

HC420LA 1.0556 420 – 520 470 – 590 17 

Chemical composition after melt analysis 

Steel grade/type 

C Si Mn P S Al Ti Nb 

Code Material no. max. % max. % max. % max. % max. % min. % max. % max. % 

HC180Y 1.0922 0.01 0.3 0.7 0.06 0.025 0.01 0.12 

HC180P 1.0342 0.05 0.4 0.6 0.08 0.025 0.015 

HC180B 1.0395 0.05 0.5 0.7 0.06 0.025 0.015 

HC220Y 1.0925 0.01 0.3 0.9 0.08 0.025 0.01 0.12 

HC220I 1.0346 0.07 0.5 0.5 0.05 0.025 0.015 0.05 

HC220P 1.0397 0.07 0.5 0.7 0.08 0.025 0.015 

HC220B 1.0396 0.06 0.5 0.7 0.08 0.025 0.015 

HC260Y 1.0928 0.01 0.3 1.6 0.1 0.025 0.01 0.12 

HC260I 1.0349 0.07 0.5 0.5 0.05 0.025 0.015 0.05 

HC260P 1.0417 0.08 0.5 0.7 0.1 0.025 0.015 

HC260B 1.0400 0.08 0.5 0.7 0.1 0.025 0.015 

HC260LA 1.0480 0.1 0.5 0.6 0.025 0.025 0.015 0.15 

HC300I 1.0447 0.08 0.5 0.7 0.08 0.025 0.015 0.05 

HC300P 1.0448 0.1 0.5 0.7 0.12 0.025 0.015 

HC300B 1.0444 0.1 0.5 0.7 0.12 0.025 0.015 

HC300LA 1.0489 0.1 0.5 1.0 0.025 0.025 0.015 0.15 0.09 

HC340LA 1.0548 0.1 0.5 1.1 0.025 0.025 0.015 0.15 0.09 

HC380LA 1.0550 0.1 0.5 1.6 0.025 0.025 0.015 0.15 0.09 

HC420LA 1.0556 0.1 0.5 1.6 0.025 0.025 0.015 0.15 0.09 

1) If a yield point is pronounced, the values for the lower yield (ReL) apply. 

2) For thicknesses > 1.2 mm, special arrangements must be made. 

3) For thicknesses ≤ 0.7 mm, but > 0.5 mm, minimum values for breaking elongation of two units lower are permissible. 

4) The minimum values for r (lat.) and n (lat.) only apply to product thicknesses > 0.5 mm. 

5) For product thicknesses > 2 mm, the r90-value is reduced by 0.2.







Surfaces 

Grade Roughness Treatment 

DIN EN 10130 b- esp. smooth Ra ≤ 0.4 µm 

Normal surface A (03) g- smooth Ra ≤ 0.9 µm oiled 

m- matt Ra > 0.6 µm ≤ 1.9 µm 

Best surface B (05) r- rough Ra > 1.6 µm un-oiled 

Multiphase steels – cold-rolled products made of multiphase steels for cold forming prEN 10338 : 2007 (draft) 


Steel grade/type Elongation limit Tensile strength Fracture elongation Work hardening Bake hardening 

exponent index 

Rp0.2 Rm A80 n10-UE BH2 N/mm2 N/mm2 % N/mm2 Code 

DP-steels 

Material no. min. min. min. min. min. 

HCT450X 1.0937 260 – 340 450 27 0.16 30 

HCT500X 1.0939 300 – 380 500 23 0.15 30 

HCT600X 1.0941 340 – 420 600 20 0.14 30 

HCT780X 1.0943 450 – 560 780 14 – 30 

HCT980X 

TRIP-steels 

1.0944 600 – 750 980 10 – 30 

HCT690T 1.0947 430 – 550 690 23 0.18 40 

HCT780T 

CP-steels 

1.0948 470 – 600 780 21 0.16 40 

HCT600C 1.0953 350 – 500 600 16 – 30 

HCT780C 1.0954 500 – 700 780 10 – 30 

HCT980C 1.0955 700 – 900 980 7 – 30 

Chemical composition (Melt analysis) 


Code 

DP-steels 

Material no. 

C 

max. 

Si 

max. 

Mn 

max. 

P 

max. 

S 

max. 


max. 

Nb + Ti 

max. 

V 

max. 

B 

max. 

HCT450X 1.0937 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT500X 1.0939 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT600X 1.0941 0.17 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780X 1.0943 0.18 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT980X 

TRIP-steels 

1.0944 0.23 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT690T 1.0947 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT780T 

CP-steels 

1.0948 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT600C 1.0953 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780C 1.0954 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT980C 1.0955 0.23 0.80 2.20 0.080 0.015 ≤ 2.00 1.20 0.15 0.22 0.005 

On request, these steels can be ordered in accordance with the steel manufacturer’s individual data sheets. 

21

22 

IX. Electrolytically galvanized sheet 


Thicknesses ab 0.30 – 3.00 mm ab 0.30 – 3.00 mm ab 0.40 – 3.00 mm 

Widths bis 1,850 mm bis 1,850 mm bis 1,530 mm bis 1,850 mm 

Lengths --- --- bis 8,000 mm bis 3,000 mm 


Soft grades – electrolytically galvanized cold-rolled flat products of steel DIN EN 10152 : 2009 

Chemical composition and mechanical properties 

Steel grade/type Symbol for the R e 1) R m A 80 2) r90 3) 4) n90 3) Melt analysis 

type of chemical composition 

surface C P S Mn Ti 

Code Material no. finishing N/mm 2 N/mm 2 min. % min. min. max. % max. % max. % max. % max. % 

DC01 1.0330 +ZE –/280 270 – 410 28 – – 0.12 0.045 0.045 0.60 – 

DC03 1.0347 +ZE –/240 270 – 370 34 1.3 – 0.10 0.035 0.035 0.45 – 

DC04 1.0338 +ZE –/220 270 – 350 37 1.6 0.170 0.08 0.030 0.030 0.40 – 

DC05 1.0312 +ZE –/200 270 – 330 39 1.9 0.190 0.06 0.025 0.025 0.35 – 

DC06 1.0873 +ZE –/180 270 – 350 41 2.1 0.210 0.02 0.020 0.020 0.25 0.3 

DC07 1.0898 +ZE –/160 250 – 310 43 2.5 0.220 0.01 0.020 0.020 0.20 0.2 

1) For products with no clear yield point, the values for the 0.2 % elongation limit (Rp0.2), are taken as those for the yield point. For other products, those for the lower yield point (ReL) apply. 

For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a 20 MPa higher maximum yield point value is permissible. For thicknesses ≤ 0.50 mm, a higher maximum yield point value of 40 MPa is permissible. 

2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, the minimum values for fracture elongation are reduced by 2 units, for thicknesses of ≤ 0.50 mm by 4 units. 

3) The r90- and n90-, determined in acc. with 7.5.2.3, only apply for product thicknesses of > 0.50 mm. 

4) For thickness > 2 mm, the r90 value sis reduced by 0.2.







Microalloyed grades – cold-rolled flat products with high yield point for cold forming made of microalloyed steels DIN EN 10268 : 2006. 

With additional coating specifications, this standard also applies for electrolytically galvanized flat products, e.g. H240LA + ZE 75/75 


Steel grade/type 0.2 % Higher yield Tensile strength Fracture Vertical Vertical Work hardening 

Elongation limit 1) point through elongation 3) anisotropy anisotropy 2) 3) 4) exponent 4) 

heat 

treatment 2) 

R p0.2 1) BH 2 R m A 80 r r n 

Code Material no. N/mm 2 N/mm 2 N/mm 2 min. lat. % max. lat. min. lat. min lat. 

HC180Y 1.0922 180 – 230 340 – 400 36 1.7 0.19 

HC180P 1.0342 180 – 230 280 – 360 34 1.6 0.17 

HC180B 1.0395 180 – 230 35 300 – 360 34 1.6 0.17 

HC220Y 1.0925 220 – 270 350 – 420 34 1.6 0.18 

HC220I 1.0346 220 – 270 300 – 380 34 1.4 0.18 

HC220P 1.0397 220 – 270 320 – 400 32 1.3 0.16 

HC220B 1.0396 220 – 270 35 320 – 400 32 1.5 0.16 

HC260Y 1.0928 260 – 320 380 – 440 32 1.4 0.17 

HC260I 1.0349 260 – 310 320 – 400 32 1.4 0.17 

HC260P 1.0417 260 – 320 360 – 440 29 

HC260B 1.0400 260 – 320 35 360 – 440 29 

HC260LA 1.0480 260 – 330 350 – 430 26 

HC300I 1.0447 300 – 350 340 – 440 30 1.4 0.16 

HC300P 1.0448 300 – 360 400 – 480 26 

HC300B 1.0444 300 – 360 35 400 – 480 26 

HC300LA 1.0489 300 – 380 380 – 480 23 

HC340LA 1.0548 340 – 420 410 – 510 21 

HC380LA 1.0550 380 – 480 440 – 560 19 

HC420LA 1.0556 420 – 520 470 – 590 17 

Chemical composition after melt analysis 

Steel grade/type 

C Si Mn P S Al Ti Nb 

Code Material no. max. % max. % max. % max. % max. % min. % max. % max. % 

HC180Y 1.0922 0.01 0.3 0.7 0.06 0.025 0.01 0.12 

HC180P 1.0342 0.05 0.4 0.6 0.08 0.025 0.015 

HC180B 1.0395 0.05 0.5 0.7 0.06 0.025 0.015 

HC220Y 1.0925 0.01 0.3 0.9 0.08 0.025 0.01 0.12 

HC220I 1.0346 0.07 0.5 0.5 0.05 0.025 0.015 0.05 

HC220P 1.0397 0.07 0.5 0.7 0.08 0.025 0.015 

HC220B 1.0396 0.06 0.5 0.7 0.08 0.025 0.015 

HC260Y 1.0928 0.01 0.3 1.6 0.1 0.025 0.01 0.12 

HC260I 1.0349 0.07 0.5 0.5 0.05 0.025 0.015 0.05 

HC260P 1.0417 0.08 0.5 0.7 0.1 0.025 0.015 

HC260B 1.0400 0.08 0.5 0.7 0.1 0.025 0.015 

HC260LA 1.0480 0.1 0.5 0.6 0.025 0.025 0.015 0.15 

HC300I 1.0447 0.08 0.5 0.7 0.08 0.025 0.015 0.05 

HC300P 1.0448 0.1 0.5 0.7 0.12 0.025 0.015 

HC300B 1.0444 0.1 0.5 0.7 0.12 0.025 0.015 

HC300LA 1.0489 0.1 0.5 1.0 0.025 0.025 0.015 0.15 0.09 

HC340LA 1.0548 0.1 0.5 1.1 0.025 0.025 0.015 0.15 0.09 

HC380LA 1.0550 0.1 0.5 1.6 0.025 0.025 0.015 0.15 0.09 

HC420LA 1.0556 0.1 0.5 1.6 0.025 0.025 0.015 0.15 0.09 

1) If a yield point is pronounced, the values for the lower yield point (ReL) apply. 

2) For thicknesses > 1.2 mm, special arrangements must be made. 

3) For thicknesses ≤ 0.7 mm, but > 0.5 mm, minimum values for breaking elongation of two units lower are permissible. 

4) The minimum values for r (lat.) and n (lat.) only apply to product thicknesses > 0.5 mm. 

5) For product thicknesses > 2 mm, the r90-value is reduced by 0.2. 

23

24 







Multiphase steels – cold-rolled products made of multiphase steels for cold forming prEN 10338 : 2007 (draft) 


Steel grade/type Elongation limit Tensile strength Fracture elongation Work hardening Bake hardening 

exponent index 

Rp0.2 Rm A80 n10-UE BH2 N/mm2 N/mm2 % N/mm2 Code 

DP-steels 

Material no. min. min. min. min. min. 

HCT450X 1.0937 260 – 340 450 27 0.16 30 

HCT500X 1.0939 300 – 380 500 23 0.15 30 

HCT600X 1.0941 340 – 420 600 20 0.14 30 

HCT780X 1.0943 450 – 560 780 14 – 30 

HCT980X 

TRIP-steels 

1.0944 600 – 750 980 10 – 30 

HCT690T 1.0947 430 – 550 690 23 0.18 40 

HCT780T 

CP-steels 

1.0948 470 – 600 780 21 0.16 40 

HCT600C 1.0953 350 – 500 600 16 – 30 

HCT780C 1.0954 500 – 700 780 10 – 30 

HCT980C 1.0955 700 – 900 980 7 – 30 

Chemical composition (melt analysis) 


Code 

DP-steels 

Material no. 

C 

max. 

Si 

max. 

Mn 

max. 

P 

max. 

S 

max. 


max. 

Nb + Ti 

max. 

V 

max. 

B 

max. 

HCT450X 1.0937 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT500X 1.0939 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT600X 1.0941 0.17 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780X 1.0943 0.18 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT980X 

TRIP-steels 

1.0944 0.23 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT690T 1.0947 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT780T 

CP-steels 

1.0948 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT600C 1.0953 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780C 1.0954 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT980C 1.0955 0.23 0.80 2.20 0.080 0.015 ≤ 2.00 1.20 0.15 0.22 0.005 

On request, these steels can be ordered in accordance with the steel manufacturer’s individual data sheets.







Surfaces 

03 Normal surface A 

05 Best surface B 

Surfaces 

Plating, zinc 

Description Nominal zinc layer Minimum zinc layer 

on each side on each side 

Two-sided Thickness µm Weight g/m2 Thickness µm Weight g/m2 ZE 25/25 2.5 18 1.7 12 

ZE 50/50 5.0 36 4.1 29 

ZE 75/75 7.5 54 6.6 47 

ZE 100/100 10.0 72 9.1 65 

One-sided Nominal zinc layer Minimum zinc layer 

on one side on one side 

ZE 25/0 2.5 18 1.7 12 

ZE 50/0 5.0 36 4.1 29 

ZE 75/0 7.5 54 6.6 47 

ZE 100/0 10.0 72 9.1 65 

Subsequent processing 

P = Phosphatized C = Chemically passivated 

PC = Phosphatized and chemically passivated CO = Chemically passivated 

PCO = Phosphatized, chemically passivated and oiled and oiled 

PO = Phosphatized and oiled O = Oiled 

S = Sealed 

Organic coating in acc. with DBL 4062 

Coating type (AA) Sheet side A Sheet side B 

.51 5 µm zinc with 

organic coating* 

as sheet side A 

.68 7.5 µm zinc with 7.5 µm zinc without organic 

organic coating* coating and without 

pre-phosphatizing 

* Organic coating: GRANOCOAT ZE, GARDO PROTECT 

Coating volume for electrolytic zinc-nickel (ZN) coatings in acc. with DIN EN 10271 

Plating zinc-nickel 

Plating code Nominal zinc-nickel coating on each side 1) Minimum zinc-nickel coating on each side 1) 

Thickness µm Volume g/m2 Thickness µm Volume g/m2 ZN20/20 2 15 1.5 11 

ZN30/30 3 22 2.4 18 

ZN40/40 4 29 3.2 23 

ZN50/50 5 37 4.1 30 

ZN60/60 6 44 5.2 38 

1) A layer thickness of 1 µ corresponds to a coating volume of approx. 7.3 g/m². 

25

26 

X. Hot-dip galvanized sheet 






Soft grades – hot-dip coated steel strip and sheet made of soft steels acc. to DIN EN 10346 : 2009 


Steel grade/type Symbol for the Elongation limit Tensile strength Fracture elongation Vertical anisotropy Work hardening 

type of R e 1) R m A 80 2) r90 exponent 

surface MPa MPa % n 90 

Code Material no. finishing min. min. min. 

DX51D 1.0226 +Z, +ZF, +ZA, +AZ, +AS – 270 – 500 22 – – 

DX52D 1.0350 +Z, +ZF, +ZA, +AZ, +AS 140 – 300 3) 270 – 420 26 – – 

DX53D 1.0355 +Z, +ZF, +ZA, +AZ, +AS 140 – 260 270 – 380 30 – – 

DX54D 1.0306 +Z, +ZA 120 – 220 260 – 350 36 1.6 4) 0.18 

DX54D 1.0306 +ZF 120 – 220 260 – 350 34 1.4 4) 0.18 

DX54D 1.0306 +AZ 120 – 220 260 – 350 36 – – 

DX54D 1.0306 +AS 120 – 220 260 – 350 34 1.4 4) 5) 0.18 5) 

DX55D 6) 1.0309 +AS 140 – 240 270 – 370 30 – – 

DX56D 1.0322 +Z, +ZA 120 – 180 260 – 350 39 1.9 4) 0.21 

DX56D 1.0322 +ZF 120 – 180 260 – 350 37 1.7 4) 5) 0.20 5) 

DX56D 1.0322 +AS 120 – 180 260 – 350 39 1.7 4) 5) 0.20 5) 

DX57D 1.0853 +Z, +ZA 120 – 170 260 – 350 41 2.1 4) 0.22 

DX57D 1.0853 +ZF 120 – 170 260 – 350 39 1.9 4) 5) 0.21 4) 

DX57D 1.0853 +AS 120 – 170 260 – 350 41 1.9 4) 5) 0.21 4) 

Chemical composition (melt analysis) of soft steels for cold forming 

Steel grade/type Symbol for the Chemical composition 

type of Percentage by mass % 

surface C Si Mn P S Ti 

Code Material no. finishing max. max. max. max. max. max. 

DX51D 1.0226 +Z, +ZF, +ZA, +AZ, +AS 0.18 0.5 1.20 0.12 0.045 0.30 

DX52D 1.0350 +Z, +ZF, +ZA, +AZ, +AS 0.12 0.5 0.60 0.10 0.045 0.30 

DX53D 1.0355 +Z, +ZF, +ZA, +AZ, +AS 0.12 0.5 0.60 0.10 0.045 0.30 

DX54D 1.0306 +Z, +ZF, +ZA, +AZ, +AS 0.12 0.5 0.60 0.10 0.045 0.30 

DX55D 1.0309 +AS 0.12 0.5 0.60 0.10 0.045 0.30 

DX56D 1.0322 +Z, +ZF, +ZA, +AS 0.12 0.5 0.60 0.10 0.045 0.30 

DX57D 1.0853 +Z, +ZF, +ZA, +AS 0.12 0.5 0.60 0.10 0.045 0.30 

Z = Hot-dip galvanized ZF = Galvannealed ZA = Galfan AZ = Galvalume AS = Hot-dip aluminised 

1) If the yield point is not pronounced, the values for the 0.2 % elongation limit (Rp0.2), apply. If pronounced, the values for the lower yield point (R eL)apply. 

2) Reduced minimum values for fracture elongation apply for product thicknesses of t > 0.50 mm (4 units less) and for 0.50 mm < t ≤ 0.70 mm (2 units less). 

3) This value only applies for cold re-rolled products (surface groups B and C). 

4) For t > 1.5 mm, the r90 value is reduced by 0.2. 

5) For t ≤ 0.70 mm, the r90 value is reduced by 0.2 and the n value by 0.01. 

90 

6) Please note the minimum fracture elongation value for DX55D + AS products, which does not follow the usual system. 

DX55D + AS products are marked according to the best heat resistance. 

Construction steels – continuously hot-dip coated steel strip and sheet made of construction steels acc. to DIN EN 10346 : 2006 

Mechanical properties (long.) 


Steel grade/type Symbol for the Elongation Tensile Fracture 

Percentage by mass % 

type of limit strength elongation 

surface R p0.2 1) R m 2) A80 3) 

finishing MPa MPa % 

Code Material no. min. min. min. 

S220GD 1.0241 +Z, +ZF, +ZA, +AZ 220 300 20 

S250GD 1.0242 +Z, +ZF, +ZA, +AZ, +AS 250 330 19 

S280GD 1.0244 +Z, +ZF, +ZA, +AZ, +AS 280 360 18 

S320GD 1.0250 +Z, +ZF, +ZA, +AZ, +AS 320 390 17 

S350GD 1.0529 +Z, +ZF, +ZA, +AZ, +AS 350 420 16 

S550GD 1.0531 +Z, +ZF, +ZA, +AZ 550 560 – 

1) If the yield point is pronounced, the values for the upper yield point (ReH) apply. 

2) For all steel grades, with the exception of S55OGD, a range of 140 MPa can be expected for tensile strength. 

3) Reduced minimum values for fracture elongation apply for product thicknesses of t > 0.50 mm (4 units less) and for 0.50 mm < t ≤ 0.70 mm (2 units less). 

C Si Mn P S 

max. max. max. max. max. 

0.20 0.60 1.70 0.10 0.045 

0.20 0.60 1.70 0.10 0.045 

0.20 0.60 1.70 0.10 0.045 

0.20 0.60 1.70 0.10 0.045 

0.20 0.60 1.70 0.10 0.045 

0.20 0.60 1.70 0.10 0.045







Microalloyed grades – continuously hot-dip coated steel strip and sheet made of steels with a high yield point for cold forming acc. to DIN EN 10346 : 2009 


Steel grade/type Symbol for the 0.2 % Elongation Bake hardening Tensile strength Fracture Vertical Work hardening 

type of limit index elongation anisotropy exponent 

surface R p0.2 1) BH 2 MPa R m A 80 2) 3) r90 3) 4) n90 

finishing min. MPa % 

Code Material no. N/mm 2 N/mm 2 N/mm 2 min. quer min. min. 

HX160YD 1.0910 +Z, +ZF, +ZA, +AZ, +AS 160 – 220 – 300 – 360 37 1.9 0.20 


HX180BD 1.0914 +Z, +ZF, +ZA, +AZ, +AS 180 – 240 35 290 – 360 34 1.5 0.16 


HX220BD 1.0919 +Z, +ZF, +ZA, +AZ, +AS 220 – 280 35 320 – 400 32 1.2 0.15 


HX260BD 1.0924 +Z, +ZF, +ZA, +AZ, +AS 260 – 320 35 360 – 440 28 – – 

HX260LAD 1.0929 +Z, +ZF, +ZA, +AZ, +AS 260 – 330 – 350 – 430 26 – – 













surface C Si Mn P S Al total Nb Ti 

Code Material no. finishing max. max. max. max. max. max. max. 

HX160YD 1.0910 +Z, +ZF, +ZA, +AZ, +AS 0.01 0.15 0.70 0.06 0.025 ≤ 0.1 0.09 0.12 


HX180BD 1.0914 +Z, +ZF, +ZA, +AZ, +AS 0.10 0.50 0.70 0.06 0.025 ≤ 0.1 0.09 0.12 





HX260LAD 1.0929 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 0.60 0.030 0.025 ≤ 0.015 0.09 0.12 










B = Bake-hardening LA = Low alloy (microalloyed) Y = Interstitial free (IF Steel) 

1) If the yield point is pronounced, the values for the lower yield point (ReL) apply. 

2) Reduced fracture elongation values for product thicknesses >0.5 mm (minus 4 units) and for thicknesses > 0.5 mm and > 0.7 mm (minus 2 units). 

3) For AS, AZ and ZF coatings, the A80 minimum values are reduced by 2 units and the r 90 minimum values by 0.2. 

4) For product thicknesses > 1.5 mm, the minimum r90 value is reduced by 0.2. 

27

28 







Multiphase steels – continuous electrolytic strip and sheet made of multiphase steels for cold forming acc. to EN 10346 : 2009 

Mechanical properties (lat.) cold-rolled products 

Steel grade/type Symbol for the Elongation limit Tensile strength Fracture elongation Work hardening Bake hardening 

type of exponent index 

surface R p0.2 1) R m A 80 1) 2) n10-UE BH 2 

finishing MPa MPa % MPa 

Code Material no. min. min. min. min. 

DP-steels 

HCT450X 1.0937 +Z, +ZF, +ZA 260 – 340 450 27 0.16 30 

HCT500X 1.0939 +Z, +ZF, +ZA 300 – 380 500 23 0.15 30 

HCT600X 1.0941 +Z, +ZF, +ZA 340 – 420 600 20 0.14 30 

HCT780X 1.0943 +Z, +ZF, +ZA 450 – 560 780 14 – 30 

HCT980X 

TRIP-steels 

1.0944 +Z, +ZF, +ZA 600 – 750 980 10 – 30 

HCT690T 1.0947 +Z, +ZF, +ZA 430 – 550 690 23 0.18 40 

HCT780T 

CP-steels 

1.0948 +Z, +ZF, +ZA 470 – 600 780 21 0.16 40 

HCT600C 1.0953 +Z, +ZF, +ZA 350 – 500 600 16 – 30 

HCT780C 1.0954 +Z, +ZF, +ZA 500 – 700 780 10 – 30 

HCT980C 1.0955 +Z, +ZF, +ZA 700 – 900 980 7 – 30 

Mechanical properties (lat.) warm-rolled products 

Steel grade/type Symbol for the Elongation limit Tensile strength Fracture elongation Work hardening Bake hardening 

type of exponent index 

surface 1) Rp0.2 Rm 1) 2) A80 n10-UE BH2 finishing MPa MPa % MPa 

Code 

FB-steels 

Material no. min. min. min. min. 

HDT450F 1.0961 +Z, +ZF 320 – 420 450 23 – 30 

HDT560F 

DP-steels 

1.0959 +Z, +ZF 460 – 570 560 16 – 30 

HDT580X 

CP-steels 

1.0936 +Z, +ZF 330 – 460 580 19 0.13 30 

HDT750C 1.0956 +Z, +ZF 620 – 760 750 10 – 30 

HDT780C 1.0957 +Z, +ZF 680 – 830 780 10 – 30 

HDT950C 

MS-steels 

1.0958 +Z, +ZF 720 – 920 950 9 – 30 

HDT1200M 1.0965 +Z, +ZF 900 – 1150 1200 5 – 30 

1) Reduced fracture elongation values for product thicknesses t < 0.5 mm (minus 4 units) and for 0.5 mm < t < 0.7 mm (minus 2 units). 

2) For ZF coatings, reduced fracture elongation values of 2 units less are valid.







Multiphase steels – continuous electrolytic strip and sheet made of multiphase steels for cold forming acc. to EN 10346 : 2009 




surface C Si Mn P S Al total Cr + Mo Nb + Ti V B 

Code 1) Material no. finishing max. max. max. max. max. max. max. max. max. 

FB-steels 

HDT450F 1.0961 +Z, +ZF 0.18 0.50 1.20 0.030 0.010 ≥ 0.015 0.30 0.05 0.15 0.005 

HDT560F 

DP-steels 

1.0959 +Z, +ZF 0.18 0.50 1.80 0.025 0.010 ≥ 0.015 0.30 0.15 0.15 0.005 

HCT450X 1.0937 +Z, +ZF, +ZA 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT500X 1.0939 +Z, +ZF, +ZA 0.14 0.80 2.00 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT600X 1.0941 +Z, +ZF, +ZA 0.17 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT580X 1.0936 +Z, +ZF 0.17 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780X 1.0943 +Z, +ZF, +ZA 0.18 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT980X 

TRIP-steels 

1.0944 +Z, +ZF, +ZA 0.23 0.80 2.50 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT690T 1.0947 +Z, +ZF, +ZA 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT780T 

CP-steels 

1.0948 +Z, +ZF, +ZA 0.32 2.20 2.50 0.12 0.015 ≤ 2.00 0.60 0.20 0.20 0.005 

HCT600C 1.0953 +Z, +ZF, +ZA 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT750C 1.0956 +Z, +ZF, 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HCT780C 1.0954 +Z, +ZF, +ZA 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT780C 1.0957 +Z, +ZF 0.18 0.80 2.20 0.080 0.015 ≤ 2.00 1.00 0.15 0.20 0.005 

HDT950C 1.0958 +Z, +ZF 0.25 0.80 2.20 0.080 0.015 ≤ 2.00 1.20 0.15 0.20 0.005 

HCT980C 

MS-steels 

1.0955 +Z, +ZF, +ZA 0.25 0.80 2.20 0.080 0.015 ≤ 2.00 1.20 0.15 0.22 0.005 

HDT1200M 1.0965 +Z, +ZF 0.25 0.80 2.00 0.060 0.015 ≤ 2.00 1.20 0.15 0.22 0.005 

F = Ferritic-bainitic X = Dual phase T = TRIP C = Complex phase M = Martensitic 

1) C = Cold-rolled products D = Warm-rolled products 

29

30 







Available coating types 

Minimum coating volume, Theoretical reference value Density 

Coating code no. in g/m², for coating thickness per side in 

on both sides µm g/cm 3 

Triple surface test Single surface test Typical value 1) Range 2) 

Zinc coating volume (Z) 

Z100 100 85 7 5 – 12 7,1 

Z140 140 120 10 7 – 15 7.1 

Z200 200 170 14 10 – 20 7.1 

Z225 225 195 16 11 – 22 7.1 

Z275 275 235 20 15 – 27 7.1 

Z350 350 300 25 19 – 33 7.1 

Z450 450 385 32 24 – 42 7.1 

Z600 

Zinc/iron alloy coating volume (ZF) 

600 510 42 32 – 55 7.1 

ZF100 100 85 7 5 – 12 7.1 

ZF120 120 100 8 6 – 13 7.1 

Zinc/aluminium alloy coating volume (ZA) 

ZA095 95 80 7 5 – 12 6.9 

ZA130 130 110 10 7 – 15 6.9 

ZA185 185 155 14 10 – 20 6.9 

ZA200 200 170 15 11 – 21 6.9 

ZA255 255 215 20 15 – 27 6.9 

ZA300 300 255 23 17 – 31 6.9 

Aluminium/zinc alloy coating volume (AZ) not for multiphase steels 

AZ100 100 85 13 9 – 19 3.8 

AZ150 150 130 20 15 – 27 3.8 

AZ185 185 160 25 19 – 33 3.8 

Aluminium/silicon alloy coating volume (AS) not for multiphase steels 

AS060 60 45 8 6 – 13 3.0 

AS080 80 60 14 10 – 20 3.0 

AS100 100 75 17 12 – 23 3.0 

AS120 120 90 20 15 – 27 3.0 

AS150 150 115 25 19 – 33 3.0 

1) Layer thicknesses can be calculated from the coating volumes. 

2) Users may assume that these limits will be maintained on the top and bottom sides. 

Surfaces 

Surface types 

NA = Usual zinc spangle in different sizes with 

usual surface 

MA = Small zinc spangle with usual surface 

MB = Re-rolled with improved surface 

MC = Re-rolled with best surface 

RA = Usual surface zinc/iron alloy 

RB = Improved surface zinc/iron alloy 

RC = Best surface zinc/iron alloy 

Subsequent surface treatment 

C = Chemically passivated 

O = Oiled 

CO = Chemically passivated and oiled 

P = Phosphatized 

PO = Phosphatized and oiled 

S = Sealed 

U = Untreated 

Coating processes 

+Z = Galvanised (99 % Zn) 

+ZF = Zinc-iron alloy (galvanealed) 

+ZA = Zinc/aluminium (Galfan, Zn + 5 % Al) 

+AZ = Aluminium/zinc (Galvalume 55 % Al + 1.6 % Sl + Zn) 

+AS = Aluminium-silicon coating (11 % Sl + Al) 

+ZM = Zinc-magnesium (1 – 2 % Mg + 1-2 % Al + Zn)* 

* yet standardised in EN 10246, available in various 

qualities and coating volumes.

XI. Your contact 

Sales Germany 

Division management 

Sales management Germany South/Export 

Mr Mockenhaupt, ppa. +49 (0) 2735/787-532 

Secretary’s office 

Ms Vogt +49 (0) 2735/787-539 

Sales management Germany-North 

Mr Becker, ppa. 

Secretary’s office 

+49 (0) 2735/787-479 

Ms Kolk +49 (0) 2735/787-347 

Region Germany North/Poland 

Mr Lieber, Hbv. +49 (0) 2735/787-245 

(deputy regional manager) 

Mr Schneider, A., Hbv. +49 (0) 2735/787-368 

Ms Brücher +49 (0) 2735/787-514 

Mr Dehnst +49 (0) 2735/787-486 

Mr Dohndorf +49 (0) 2735/787-367 

Mr Kepp +49 (0) 2735/787-364 

Mr Löhr +49 (0) 2735/787-530 

Ms Lück +49 (0) 2735/787-207 

Ms Mies +49 (0) 2735/787-494 

Mr Müller +49 (0) 2735/787-571 

Mr Reinschmidt +49 (0) 2735/787-592 

Ms Rother +49 (0) 2735/787-365 

Mr Schlechtriemen +49 (0) 2735/787-220 

Mr Schmidt +49 (0) 2735/787-352 

Mr Wagener +49 (0) 2735/787-572 

International Sales 

Sales Benelux 

Mr Jos Bergmans 

Mgr. Kuypersplein 2 · NL-5556 VS Valkenswaard 

Tel. +31/402049911 

Mobile +31/651887324 

Fax +31/402043833 

Purchasing 

Purchasing manager 

Mr Latsch, ppa. +49 (0) 2735/787-470 

Purchasing 

Mr Hennrichs +49 (0) 2735/787-611 

Ms Henrich +49 (0) 2735/787-246 

Mr Kreutz +49 (0) 2735/787-296 

Ms Roth +49 (0) 2735/787-527 

Ms Schmalfuß +49 (0) 2735/787-266 

Mr Vehma +49 (0) 2735/787-496 

Sales Perforated metal 

Division management 

Mr Seidel +49 (0) 2735/787-267 

Secretary’s office +49 (0) 2735/787-449 

Post codes 1, 2, 0, Poland and Denmark 

Mr Porr +49 (0) 2735/787-265 

External sales: Germany-North 

post codes 32-37, 40-49, 50-53, 57-59 

Mr Lichtenberg +49 (0) 2151/783711 

Fax +49 (0) 2151/783712 

Mobile +49 (0) 170/5642940 

Region Germany-Middle/North post codes 3 

Mr Beimborn +49 (0) 2735/787-201 

Fax +49 (0) 2735/787-498 

Mobile +49 (0) 160/8810682 

Region Germany-South/Export 

Mr Richter, Hbv. +49 (0) 2735/787-487 

(deputy regional manager) 

Mr Ermert, Hbv +49 (0) 2735/787-492 

Mr Fichtner +49 (0) 2735/787-626 

Mr Kempe +49 (0) 2735/787-533 

Mr Loch +49 (0) 2735/787-380 

Ms Merschmann +49 (0) 2735/787-529 

Ms Schmidt +49 (0) 2735/787-407 

Mr Schulte +49 (0) 2735/787-489 

Mr Schupp +49 (0) 2735/787-542 

Mr Stolz +49 (0) 2735/787-251 

Ms Veen +49 (0) 2735/787-507 

Ms Werthebach +49 (0) 2735/787-411 

External sales: Germany-South, 

post codes 54-56, 6, 75-77, 79 

Mr Oberkirsch +49 (0) 6841/994380 

Fax +49 (0) 6841/994381 

Mobile +49 (0) 170/5633504 

Sales Poland 

Mr Michał Ulman 

Mobile +48/603248103 

Fax +49 (0) 21315631118 

Quality management/ 

Technical consulting 

Quality management 

Mr Baumunk +49 (0) 2735/787-291 

(Manager) 

Technical consulting/Quality 

Mr Schilling +49 (0) 2735/787-242 

(Manager) 

Mr Großmann +49 (0) 2735/787-286 

Fax +49 (0) 2735/787-288 

Post code 3, Benelux 

Mr Boller +49 (0) 2735/787-250 

Post codes 4, 58, 59 

Mr Werle +49 (0) 2735/787-295 

Post codes 50-57, 66, Benelux and France 

Mr Diehl +49 (0) 2735/787-394 

External sales: Germany-South, 

post code 6,7, Austria and Switzerland 

Mr Pasternacki +49 (0) 7071/7956999 

Fax +49 (0) 7071/9150738 

Mobile +49 (0) 151/14620109 

External sales: 

Germany-South, post codes 8-9 

Mr Gaube +49 (0) 991/2703152 

Fax +49 (0) 991/2910964 

Mobile +49 (0) 170/5633385 

External sales: 

Germany East, post code 0-15, 98-99 

Herr Lippa +49 (0) 3641/6360947 

Fax +49 (0) 3641/6360948 

Mobile +49 (0) 151/12143099 

Sales Czechia/Slowakia 

Mr Vladimír Táborský 

Družstevní 499 

CZ-28922 Lysá nad Labem 

Tel./Fax +420/325-575585 

Mobile +420/0602124076 

Post codes 6, 9 

Mr Heinze +49 (0) 2735/787-420 

Post code 8, Czechia 

Mr Düber +49 (0) 2735/787-595 

Post codes, 88, 89, Austria and Switzerland 

Mr Weinbrenner +49 (0) 2735/787-433 

31

More information? 

Perforated metal made to measure – 

individual and fast 

Our location 

Neunkirchen plant 

28 

EMW Stahl Service GmbH 

Pfannenbergstraße 1 

D-57290 Neunkirchen/Siegerland 

Phone +49 (0) 2735/787-02 · Fax +49 (0) 2735/787-484 

E-Mail: info@emw-stahlservice.de 

Internet: www.emw-stahlservice.de 

Print no. 0293/05.11. We reserve the right to make technical alterations

The Centre of Excellence for Sheet - EMW Eisen- und Metallhandel ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?