Open CNC Screen Display Function

More documents

Recommendations

Info

1.SETUP B-63164EN/04 1.2 SETUP (ETHERNET VERSION) This section describes information related to the setup of the Ethernet version of the CNC screen display function. See Section 1.1, "Setup (HSSB Version)," for explanations about the setup of the HSSB version of the CNC screen display function. - 6 -
B-63164EN/04 1.SETUP 1.2.1 Operating Environment The software operating environment for the CNC screen display function is as follows: � Environmental requirements For the Windows 95/98 - Pentium 100 MHz or better processor - 16 MB of memory (minimum) For Windows NT4.0/2000 - Pentium 120 MHz or better processor - 32 MB of memory (minimum) � Recommended operating environment For the Windows 95/98 - Pentium 120 MHz or better processor - 32 MB of memory (minimum) For Windows NT4.0/2000 - Pentium 150 MHz or better processor - 64 MB of memory (minimum) � Display - Resolution : 640 × 480 or higher resolution - Color : 256 colors or more (16-color mode cannot be used) � Required hard disk space - 10 MB or more NOTE 1 The CNC screen display function runs under Windows 95/98 or Windows NT4.0/2000. 2 Maximum performance sometimes cannot be achieved depending on the type, performance, and usage of the personal computer. 3 As with other Windows applications, this function is subject to restrictions when operating in multitasking mode. That is, the CNC screen display function affects the execution speed of other applications, and other applications affect the execution speed of the CNC screen display function. - 7 -
Page 1 and 2: CNC Screen Display Function OPERRAT
Page 3 and 4: B-63164EN/04 SAFETY PRECAUTIONS SAF
Page 5 and 6: B-63164EN/04 SAFETY PRECAUTIONS CAU
Page 7 and 8: B-63164EN/04 PREFACE PREFACE Thank
Page 9 and 10: B-63164EN/04 PREFACE � The FS160i
Page 11 and 12: B-63164EN/04 PREFACE � When the C
Page 13 and 14: B-63164EN/04 PREFACE ORGANIZATION O
Page 15 and 16: B-63164EN/04 TABLE OF CONTENTS TABL
Page 17 and 18: B-63164EN/04 1.SETUP 1 SETUP This c
Page 19 and 20: B-63164EN/04 1.SETUP 1.1.1 Operatin
Page 21: B-63164EN/04 1.SETUP 1.1.3 Uninstal
Page 25 and 26: B-63164EN/04 1.SETUP 1.2.3 Uninstal
Page 27 and 28: B-63164EN/04 2.OPERATION 2.1 START
Page 29 and 30: B-63164EN/04 2.OPERATION 5. To disp
Page 31 and 32: B-63164EN/04 2.OPERATION 2.1.2 Star
Page 33 and 34: B-63164EN/04 2.OPERATION (1) CNC nu
Page 35 and 36: B-63164EN/04 2.OPERATION � When t
Page 37 and 38: B-63164EN/04 2.OPERATION When the f
Page 39 and 40: B-63164EN/04 2.OPERATION A pop-up m
Page 41 and 42: B-63164EN/04 2.OPERATION 2.2.3 Term
Page 43 and 44: B-63164EN/04 2.OPERATION 2.2.4 Term
Page 45 and 46: B-63164EN/04 2.OPERATION 2.3 INPUT
Page 47 and 48: B-63164EN/04 2.OPERATION 2.4 INPUT
Page 49 and 50: B-63164EN/04 2.OPERATION 2. The fun
Page 51 and 52: B-63164EN/04 2.OPERATION 2. The [Da
Page 53 and 54: B-63164EN/04 2.OPERATION NOTE 1 Whe
Page 55 and 56: B-63164EN/04 2.OPERATION 2.7 DISPLA
Page 57 and 58: B-63164EN/04 3.SETTING 3.1 SWITCHIN
Page 59 and 60: B-63164EN/04 3.SETTING 3.2 SETTING
Page 61 and 62: B-63164EN/04 3.SETTING 3. Choose a
Page 63 and 64: B-63164EN/04 3.SETTING ��
Page 65: APPENDIX
Page 68 and 69: A.ALARMS APPENDIX B-63164EN/04 �
Page 70 and 71: B.CNC SCREEN DISPLAY FUNCTION FOR T
Page 72 and 73:
B.CNC SCREEN DISPLAY FUNCTION FOR T
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 83:
B-63164EN/04 INDEX Index AAAA ALARM
show all

Open CNC Screen Display Function

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?