ANODOS DE MAGNESIO (Mg) PARA PROTECCION ... - sisman
ANODOS DE MAGNESIO (Mg) PARA PROTECCION ... - sisman
ANODOS DE MAGNESIO (Mg) PARA PROTECCION ... - sisman
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
ESPECIFICACION TECNICA <strong>DE</strong> MATERIALES<br />
<strong>ANODOS</strong> <strong>DE</strong> <strong>MAGNESIO</strong> (MG) <strong>PARA</strong><br />
<strong>PROTECCION</strong> CATODICA<br />
PDVSA EM–28–07/02<br />
REVISION FECHA<br />
2 MAY.97<br />
Página 6<br />
.Menú Principal Indice manual Indice volumen Indice norma<br />
TABLA 1. COMPOSICION QUIMICA <strong>PARA</strong> <strong>ANODOS</strong> <strong>DE</strong><br />
ALEACION <strong>DE</strong> <strong>MAGNESIO</strong><br />
NACE Tipo III Tipo II Tipo I <strong>Mg</strong>/Mn<br />
ASTM B483 AZ63B AZ63C AZ63D M1C<br />
4.1.2 Núcleo<br />
Al 5.3 – 6,7 5,3 – 6,7 5 –7 0.01 máx.<br />
Zn 2,5 – 3,5 2,5 – 0,7 2 – 4 –––––––<br />
Mn 0,15 – 0,7 0,15 – 0,7 0,15 – 0,7 0,5 – 1,3<br />
Si 0,10 máx. 0,3 máx. 0,3 máx. 0,05<br />
Cu 0,02 máx. 0,05 máx. 0,10 máx. 0,02<br />
Ni 0.002 máx. 0.003 máx. 0.003 máx. 0.001<br />
Fe 0.003 máx. 0.003 máx. 0.003 máx. 0.03<br />
Otros 0.3 máx. 0.3 máx. 0.3 máx. 0,3 máx.<br />
<strong>Mg</strong> remanente remanente remanente remanente<br />
a. Las abrazaderas, tubos, canales, pletinas y alambres deben estar hechas de<br />
acero al carbono galvanizado en caliente de acuerdo a las normas ASTM A–123<br />
y ASTM A –153, según el servicio y tipo de ánodo.<br />
b. Los núcleos deberán fabricarse de planchas de acero estructural soldable y/o de<br />
secciones de tubos soldables de acuerdo con la norma ASTM A–106.<br />
c. El carbono equivalente del material del núcleo no deberá exceder de 0,45%. de<br />
acuerdo con la norma NACE RP–0387–90. El valor del carbono equivalente<br />
(Cev) deberá ser calculado con la fórmula siguiente:<br />
Cev C Mn<br />
6<br />
Cr Mo V<br />
5<br />
<br />
Ni Cu<br />
15<br />
NOTA: Cada elemento deberá expresarse en % en peso.<br />
d. Los núcleos galvanizados según lo indicado en el punto a., deben tener la<br />
superficie libre de óxidos, decoloraciones, daños mecánicos y contaminaciones<br />
asociables al momento de la fundición del material anódico (SSPC–SP1).<br />
4.1.3 Soportes de apernamiento<br />
a. Los ángulos y otros componentes para soporte de apernamiento serán de<br />
material ASTM–A36.<br />
b. Los soportes y conjunto de apernamiento (tornillos, tuerca, arandela plana y de<br />
presión), deberán ser galvanizados en caliente de acuerdo a las normas<br />
ASTM–123–90 y ASTM 153–82, según el servicio y tipo de ánodo.