TURBINAS DE CANAL LATERAL SKS / SKH - Ferromar

More documents

Recommendations

Info

1. Safety requirements:GRIÑÓ-ROTAMIK1.1) All the works of transportation, installation, maintenance and troubleshooting must beexecuted by a responsible, qualified personnel.1.2) This device must be set up according to this instruction manual.1.3) The grounding wire must be connected well accordingly.1.4) The lead wires as a conductor to the power supply should be properly sized and havestrain relief to the wires at the connection terminals. If this is failed, electric shock and firewill be possible.1.5) While rotating, human body must keep away from the rotating portion such as the CoolingFan and do no reach into the device through the intake or outlet.1.6) Once the power electricity was interrupted, the power switch must be turned offimmediately.1.7) If the device couldn’t accelerate up to its rated speed in 15 seconds from the power switchturned on, please turn off the power immediately and check it carefully.1.8) The power supply must be turned off before moving, maintaining, or repairing this device.Please note that, due to rotating inertia, the device may continue to run several minutesafter power turned off.1.9) These devices are only used to handle or conveying dust free air, non-combustible, noncorrosiveand non-explosive gases, vapors or liquids.1.10) The intake must be properly sited and covered so that no dirt or solid particles can besucked in.1.11) When the device is operated at impermissible high pressure condition, a suitablepressure-relief valve must be used to prevent overheating of motor.1.12) The End Cover is used to prevent contact and direct the cooling air flow, can not beremoved; otherwise the motor will get overheating.8
2. InstallationGRIÑÓ-ROTAMIK2.1) Application:2.1.1) The Side Channel Blowers are used to handle non-combustible, non-corrosive and nonexplosivegases and air. The ambient or gas temperature should be less than 40ºC.2.1.2) Dirt and solid particle must be filtered before entering intake of the device.2.1.3) These devices are designed for continuous operation, in case of non-continuous running orhigh ambient temperature, checking suitability (maximum permissible temperature) with therepresentatives of manufacturer.2.1.4) The permissible pressure for operation is shown in the general catalogue2.1.5) These devices must not be operated with closed intake or outlet.2.2) Installation:2.2.1) The Side Channel Blowers can be installed in any direction, but when mounted vertically, themotor side should be upward.2.2.2) To avoid vibration, the unit must be mounted on a rigid base.2.2.3) To ensure perfect cooling, the minimum clearances between the Front Cover or Cover andthe walls should be 20mm. Make sure too, no obstructions in the cooling air flow system.2.2.4) Any flammable materials must be kept away from the unit.2.2.5) Air and gases should be filtered before entering the intake by an intake or inline filter.2.2.6) To reduce noise, additional silencers are optional.2.3) Electrical Connection:WARNING: No any connecting work is allowed before the electrical powerdisconnected.2.3.1) The supplied power voltage must be the same as the rating stated on the name plate.2.3.2) The lead wires must be connected according to the diagram attached on the terminal box.2.3.3) The protective earth conductor must be connected to the grounding terminal.2.3.4) Select correct circuit breakers to the current rating of motors.9
Page 1: TURBINAS DE CANAL LATERAL SKS / SKH
Page 4 and 5: 3. Operación:GRIÑÓ-ROTAMIK3.1) E
Page 6 and 7: DESPIECE SKS-SKH / EXPLODED VIEW SK
Page 10 and 11: 3. Operation:GRIÑÓ-ROTAMIK3.1) Th
Page 12 and 13: DESPIECE SKS-SKH / EXPLODED VIEW SK

TURBINAS DE CANAL LATERAL SKS / SKH - Ferromar

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?