Dynamic Looper owner's manual - Vox

More documents

Recommendations

Info

VOX Dynamic Looper Owner's manual If you’ve selected a tempo-synchronized delay or a tape echo, use this parameter to select one of the following values. 1-64: (64th notes) 1-6: 3 (quarter note triplets) 1-32: (32nd notes) 3-16: (dotted eighth notes) 1-24: 3 (16th note triplets) 1-4: (1 beat = quarter note) 1-16: (16th notes) 1-3: 3 (half note triplets) 1-12: 3 (eighth note triplets) 3-8: (one and a half beats) 1-8: (eighth notes) 1-2: (two beats = half note) • Control pedal: Controls the depth of the effect. Note: When using a delay effect with the Pre Effect and Loop Effect, the maximum delay time for each will be 2.22 seconds. If you’re using a tempo-synchronized delay effect, and the tempo together with the effect parameter setting would cause the delay time to exceed 2.22 seconds, the delay time will automatically be reduced to 1/2 the setting. rVb: REVERB This is a reverb effect that lets you use the control pedal to control the reverb depth and volume balance. It is effective on either guitar or mic input. • EDIT knob: Selects the type of reverb. SPr: Models the spring reverb built into a guitar amp. roo: Models the reverberation of a typical room containing numerous early reflections. HAL: Models the reverberation of a concert hall containing numerous echo components. • Control pedal: Controls the reverb depth and volume balance. S-F: SCI-FI This transforms the sound of an electric guitar in a variety of ways. • EDIT knob: Selects the type of sound. dr1, dr2, dr3: These are drone effects that add a continuous drone pitch like the Tambura, an instrument of India. Sy1, Sy2, Sy3: These model a chromatic synth. There are three synth types, each with a different tonal character (Sy3: Drum simulation). They are effective when played with single notes. SLo: This produces a violin-like effect with a slower attack. • PRE FX button + EDIT knob: What this adjusts will depend on the sound you’ve selected. dr1, dr2: Specifies the key. dr3, Sy1, Sy2: Specifies the depth of the effect. Sy3: Specifies the output level. SLo: Specifies the speed of the attack. • Control pedal: What this controls will depend on the sound you’ve selected. dr1, dr2: Controls the depth of the effect. dr3: Controls the key. Sy1, Sy2, SLo: Controls the output level. Sy3: Controls the tonal character. 32
About the Pre Effect and the Loop Effect Loop Effects When using a loop effect, it is particularly useful to assign a loop effect parameter to the control pedal. Vol: VOLUME This effect lets you use the control pedal to control the volume. If you start resampling with this effect selected, the output whose volume is controlled by this effect will be recorded on the currently selected loop. You can also use this to combine the outputs of the two loops into a single loop. • EDIT knob: Specifies the sound(s) whose volume will be controlled. Cur: The volume of the loop that’s currently selected will be controlled. L1.2: The volume of Loop 1 and Loop 2 will be controlled. ALL: The volume of the input sound, Loop 1, and Loop 2 will be controlled. • Control pedal: Controls the volume of the sound(s) specified by the EDIT knob. FAd: X-FADE This effect uses the control pedal to control the mix balance. If you execute resampling with this effect selected, the mix output controlled by the Loop Effect will be recorded into the currently selected loop. • EDIT knob: Specifies the sounds whose mix balance will be controlled. In.L: The pedal will control the mix balance between the input and the loop that’s currently selected. L1.2: The pedal will control the mix balance between Loop 1 and Loop 2. • Control pedal: Controls the mix balance specified by the EDIT knob. rEV: REVERSE This effect reverses the playback. Advancing the control pedal will increase the mix amount of reverse playback. This is particularly effective when used on audio that contains continuous change, such as a guitar solo or vocal. • EDIT knob: Selects what will happen when you switch between forward and reverse playback. FAd: Crossfade between forward playback and reverse playback. ALt: Switch alternately between forward playback and reverse playback. • Control pedal: Switches between forward playback and reverse playback. LIL: LOOP IN LOOP When you advance the control pedal, this effect instantly creates an even shorter phrase from the phrase that’s currently playing. By controlling the length of the phrase, you can also produce roll-like effects. • EDIT knob: Specifies the time signature used when you advance the control pedal while a phrase is playing back. 33
Page 3 and 4: Dynamic Looper Owner’s manual
Page 5 and 6: IMPORTANT NOTICE TO CONSUMERS T
Page 7 and 8: Table of contents Applying the Loop
Page 9 and 10: Introduction How the Dynamic Looper
Page 11 and 12: Panels 1. Program/loop control sect
Page 13 and 14: Panels a. Loop Effect selector This
Page 15 and 16: Panels d. CANCEL button Press this
Page 17 and 18: Connections 1. Make sure that the D
Page 19 and 20: Creating phrases Red: The Pre Effec
Page 21 and 22: Creating phrases The recording leng
Page 23 and 24: Overdubbing a performance by playin
Page 25 and 26: Resampling Specifying how the loop
Page 27 and 28: Erasing a loop-recorded phrase Eras
Page 29 and 30: About the Pre Effect and the Loop E
Page 31: About the Pre Effect and the Loop E
Page 39 and 40: Control pedal settings Control peda
Page 41 and 42: Auto Power-Off function Auto Power-
Page 43 and 44: Block diagram Block diagram Edit Ed
Page 45 and 46: Dynamic Looper Manuel d’utilisati
Page 47 and 48: 47
Page 49 and 50: Sommaire Traiter une phrase enregis
Page 51 and 52: Structure du Dynamic Looper Le Dyna
Page 53 and 54: Panneaux 1. Section de pilotage du
Page 55 and 56: Panneaux b. Bouton LOOP FX Ce bouto
Page 57 and 58: Panneaux d. Bouton CANCEL Appuyez s
Page 59 and 60: Connexion de l’instrument et mise
Page 61 and 62: Créer des phrases Orange: Le pré-
Page 63 and 64: Créer des phrases fonction du temp
Page 65 and 66: Ajout d’un nouvel enregistrement
Page 67 and 68: Mode d’arrêt de la boucle Vous p
Page 69 and 70: Effacer la phrase d’une boucle Ef
Page 71 and 72: Pré-effets et effets de boucle Cet
Page 73 and 74: Pré-effets et effets de boucle Stt
Page 75 and 76: Pré-effets et effets de boucle Eff
Page 77 and 78: Pré-effets et effets de boucle dch
Page 79 and 80: Pré-effets et effets de boucle Edi
Page 81 and 82: Réglages de la pédale d’express
Page 83 and 84:
Coupure automatique d’alimentatio
Page 85 and 86:
Schéma de principe Schéma de prin
Page 87 and 88:
Dynamic Looper Bedienungsanleitung
Page 89 and 90:
WICHTIGER HINWEIS FÜR KUNDEN D
Page 91 and 92:
Inhaltsübersicht Bearbeiten aufgez
Page 93 and 94:
Vorweg Aufbau des Dynamic Looper De
Page 95 and 96:
Bedienelemente 1. Steuerung der Pro
Page 97 and 98:
Bedienelemente a. Wahlregler Hiermi
Page 99 and 100:
Bedienelemente d. CANCEL-Taster Dr
Page 101 and 102:
Anschlüsse 1. Stellen Sie den STAN
Page 103 and 104:
Aufzeichnen von Phrasen Rot: Der Pr
Page 105 and 106:
Aufzeichnen von Phrasen Exakte Län
Page 107 and 108:
Ergänzen einer Phrase um weitere P
Page 109 and 110:
Festlegen, wie die Schleife endet T
Page 111 and 112:
Löschen einer Loop-Phrase Bearbeit
Page 113 and 114:
Über den Pre- und Loop-Effekt In d
Page 115 and 116:
Über den Pre- und Loop-Effekt Stt:
Page 117 and 118:
Über den Pre- und Loop-Effekt Loop
Page 119 and 120:
Über den Pre- und Loop-Effekt SPd:
Page 121 and 122:
Über den Pre- und Loop-Effekt Edit
Page 123 and 124:
Einstellungen für das Expression-P
Page 125 and 126:
Energiesparfunktion Energiesparfunk
Page 127 and 128:
Blockschaltbild Blockschaltbild Edi
show all

Dynamic Looper owner's manual - Vox

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?