MB1000 Instructions - Panamax!
MB1000 Instructions - Panamax!
MB1000 Instructions - Panamax!
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
RS-232 Communications Protocol & Command Set<br />
BATTERY LEVEL STATUS<br />
Requests the battery level, expressed as a percentage of maximum<br />
(full charge).<br />
Send Query to UPS:<br />
Action:<br />
Response:<br />
?BATTERYSTAT<br />
Load level will be displayed<br />
$BATTERY = xxx<br />
xxx is the battery charge level (percentage of maximum charge)<br />
expressed in decimal format. If the value is less than 100, the<br />
hundreds digit is represented with a 0.<br />
____________________________________________<br />
LIST CONFIGURATION<br />
Requests a list of all configurable parameters and current settings.<br />
Send Query to UPS:<br />
Action:<br />
?LIST_CONFIG<br />
List of configurable parameters and<br />
current settings will be displayed.<br />
Response:<br />
$BTHRESH = level<br />
$BUZZER = mode<br />
$AVR = mode<br />
$FEEDBACK = mode<br />
LINEFEED = mode<br />
$BRIGHTNESS = xxx<br />
$SCROLL_MODE = xxx<br />
$SLEEP_MODE = xxx<br />
____________________________________________<br />
List of all commands and queries<br />
Send Query to UPS:<br />
Action:<br />
Response:<br />
?HELP<br />
List of all commands and queries<br />
will be displayed<br />
!ALL_ON<br />
!ALL_OFF<br />
!SWITCH<br />
!SET_BATTHRESH<br />
!SET_BUZZER<br />
!SET_AVR<br />
!SET_FEEDBACK<br />
!SET_LINEFEED<br />
!RESET_ALL<br />
!SET_BRIGHT ?VOLTAGE<br />
!SET_SCROLLMODE ?LOADSTAT<br />
!SET_SLEEPMODE ?BATTERYSTAT<br />
?ID<br />
?LIST_CONFIG<br />
?OUTLETSTAT ?HELP<br />
?POWERSTAT<br />
_________________________________________<br />
RESPONSES & MESSAGES<br />
OUTLET STATUS CHANGE<br />
CONDITION<br />
RESPONSE<br />
Outlet Bank 1 changes state $BANK1 = status<br />
Outlet Bank 2 changes state $BANK2 = status<br />
status = {ON, OFF}<br />
_________________________________________<br />
POWER BUTTON STATUS CHANGE<br />
CONDITION<br />
Power Button changes<br />
ON/OFF status<br />
RESPONSE<br />
$BUTTON = status<br />
status = {ON, OFF}<br />
_________________________________________<br />
POWER FAULT STATUS CHANGE<br />
CONDITION<br />
Overvoltage State<br />
Undervoltage State<br />
Lost Power State<br />
Test Mode<br />
Recovery Mode<br />
Normal Operation Mode<br />
Low Battery<br />
AVR Stage<br />
Remaining Backup Time<br />
Battery State<br />
RESPONSE<br />
$PWR = OVERVOLTAGE<br />
$PWR = UNDERVOLTAGE<br />
$PWR = LOST POWER<br />
$PWR = TEST<br />
$PWR = RECOVERY<br />
$PWR = NORMAL<br />
$LOWBAT<br />
$AVRSTATE = state<br />
state = {BOOST, BUCK}<br />
$TIME = xxx<br />
xxx = backup time<br />
$BATTSTATE = xxx<br />
xxx = {CHARGE, DISCHARGE, FULL}<br />
Power Control Software<br />
Complete <strong>Instructions</strong> are available by clicking on Help on the<br />
Power Control Software welcome screen.<br />
12