BA ROWELD ROFUSE Sani 160 Anf... - Rothenberger South Africa

More documents

Recommendations

Info

5 Self-Monitoring Functions Overview 5.1 System Error CAUTION! The welding unit has to be disconnected immediately from the power supply and the fitting. The auto-test has found an error in the system. The unit must no longer be operated and has to be turned in for check and repair. 5.2 Power Supply Failure The last welding is incomplete. The welding unit was disconnected from the power supply. This error has to be acknowledged by pressing the STOP key. 5.3 No Contact There is no properly established electric contact between the welding unit and the fitting (check push-on terminal on fitting), or the heater coil is defective. 5.4 Low Voltage The input voltage is below 180 V. Adjust generator output voltage. 5.5 Overvoltage The input voltage is above 280 V. Adjust generator output voltage. 5.6 Temperature Error or Temperature Sensor Defective The measured ambient temperature is outside the operating range of the welding unit, i.e., below – 5 °C or over + 40 °C. If this error is displayed during the unit’s auto-test, the temperature sensor is defective. 5.7 Frequency Error The frequency of the input voltage is out of tolerance (40 Hz - 70 Hz). 5.8 Low or Excess Current The message is displayed if the there is a momentary current failure or if the current regulator is defective. 5.9 Emergency Off The welding process has been interrupted by pressing the STOP key. 24 ENGLISH E0 E1 E2 E3 E4 E5 E6 E7 E8
5.10 Fitting Already Welded After welding was finished, the fitting was not disconnected from the welding unit, and the user attempted to weld the same fitting a second time. E9 ENGLISH 25
Page 1 and 2: 5.4230 ® ROWELD ROFUSE Sani 160 Be
Page 3 and 4: Inhalt 1 Sicherheitshinweise.......
Page 5 and 6: 1 Sicherheitshinweise Beim Gebrauch
Page 7 and 8: und ausbildungsberechtigte Person z
Page 9 and 10: 4 Bedienung 4.1 Allgemeine Informat
Page 11 and 12: 5 Auflistung der Überwachungsfunkt
Page 13 and 14: 6 Störungen 6.1 Gerät reagiert na
Page 15 and 16: 8 Anschrift für Wartung und Repara
Page 17 and 18: Introduction Dear Customer: Thank y
Page 19 and 20: 1.8 Opening the Unit Do not remove
Page 21 and 22: 2 Service and Repair As the unit is
Page 23: 4.5 Welding Process The welding pro
Page 27 and 28: 7 ROWELD® ROFUSE Sani 160 Technica
Page 29 and 30: Table des matières 1 Consignes de
Page 31 and 32: 1 Consignes de sécurité Lors de l
Page 33 and 34: sous la surveillance d’une person
Page 35 and 36: 4 Fonctionnement 4.1 Informations g
Page 37 and 38: 5 Liste des fonctions d’auto-cont
Page 39 and 40: 6 Dépannage 6.1 Aucune réaction d
Page 41 and 42: 8 Coordonnées pour l’entretien e
Page 43 and 44: Inleiding Geachte klant! Wij bedank
Page 45 and 46: mag het apparaat alleen door een ge
Page 47 and 48: 2 Onderhoud en reparatie Omdat het
Page 49 and 50: 4.6 Einde van het lasproces Het las
Page 51 and 52: 5.9 Nood-Uit Het lasproces zal met
Page 53 and 54: 7 Technische gegevens van de ROWELD
Page 55 and 56: Zubehör und Ersatzteile / Accessor

BA ROWELD ROFUSE Sani 160 Anf... - Rothenberger South Africa

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?