MODUCONTROL

More documents

Recommendations

Info

To access the USER menu, press the key in (Fig.7). Once the key has been pressed, you must insert the password to access the various menus; to access the user menu, the password is 000 (displayed by default). To modify the value of the passwords, use the arrow keys. When you have inserted the correct 38 PASSWORD = 000 USER menu password, press the key in (Fig.7). The monitor will show the index of the USER parameter and a 3-character string that identifi es it; the string will be displayed for one second, after which it is replaced by the value of the parameter itself. To move on to the next parameter, use the arrow keys (Fig.8). To modify a pa- R Fig.7 Fig.8 rameter, just select it, press the key in (Fig.7), modify the assigned value using the arrow keys in (Fig.8), and confi rm the modifi cation by pressing the key in (Fig.7) again. Setting operational parameters (user level) Index - String j Index - String MIN value MAX value 0 1 MIN value MAX value j Parameters visible in the heat pump models j Setting of operational mode (HOT/COLD) Parameter function This parameter identifies the functioning mode set for the unit: • set value = 0 - Cooling mode; • set value = 1 - Heating mode. In cooling only units, this parameter is displayed but it cannot be modified. In software versions prior to 3.75, to make the season change the unit must be in standby. Setting of cooling temperature Parameter function -20°C 26°C This parameter indicates the value of the work setting active in cooling mode. Parameters visible in the models with DCP installed j j Parameters visible in bicompressor models Parameters visible in the models with inverter compressor Parameters visible in the models that produce domestic water R
Index - String Index - String j Index - String j Index - String MIN value MAX value 1°C 20°C MIN value MAX value 25°C 65°C MIN value MAX value 1°C 20°C MIN value j Parameters visible in the heat pump models j Parameters visible in the models with DCP installed Setting of proportional cooling band j j Parameter function This parameter indicates the proportional band applied to the cooling set; this band produces the optimised management of the compressor, only switching it on if the inlet/ outlet water temperature (depending on the type of control set by parameter (0) in the installer menu) is greater than the cooling work set (parameter (1) user menu) plus the value of this parameter. Setting of heating temperature Parameter function This parameter indicates the value of the work setting active in heating mode. In cooling only units, this parameter is displayed but it cannot be modified. Setting of proportional heating band Parameter function This parameter indicates the proportional band applied to the heating set; this band produces the optimised management of the compressor, only switching it on if the inlet/ outlet water temperature (depending on the type of control set by parameter (0) in the installer menu) is less than the heating work set (parameter (3) user menu), minus the value of this parameter. In cooling only units, this parameter is displayed but it cannot be modified. Settings made on the basis of outside temperature MAX value 0 3 Parameter function This setting activates the algorithm of compensation of the work setting: (°C) SF1 SET (F) SF2 SET (H) SET TF1(G) SET TF2(I) SF1: index (6) user menu; SF2: index (8) user menu; TF1: index (7) user menu; TF2: index (9) user menu; (°C) In cooling mode, the work setting is calculated automatically on the basis of the outside temperature, following the logic highlighted in the diagram. (°C) SET SC1(J) SET SC2(N) Parameters visible in bicompressor models SET TC1 (L) SET TC2(O) SC1: index (A) user menu; SC2: index (C) user menu; TC1: index (B) user menu; TC2: index (d) user menu; Parameters visible in the models with inverter compressor Parameters visible in the models that produce domestic water (°C) In heating mode, the work setting is calculated automatically on the basis of the outside temperature, following the logic highlighted in the diagram. 39
Page 1: REGOLAZIONE ELETTRONICA ELECTRONIC
Page 4 and 5: Indice Precauzioni e norme di sicur
Page 6 and 7: 6 Precauzioni e norme di sicurezza
Page 8 and 9: 8 Settaggi default MODU CONTROL Men
Page 10 and 11: 10 Visualizzazioni interfaccia uten
Page 12 and 13: Per entrare nel menù UTENTE premer
Page 14 and 15: 14 Indice - stringa Indice - string
Page 16 and 17: Per entrare nel menù INSTALLATORE
Page 18 and 19: 18 Indice - stringa Indice - string
Page 20 and 21: j Parametri visibili nei modelli a
Page 22 and 23: Per entrare nel menù RESISTENZA pr
Page 24 and 25: Oltre ai parametri inseribili da pa
Page 26 and 27: Le unità prevedono due tipologie n
Page 28 and 29: 28 32 132 Sovratemperatura aletta d
Page 30 and 31: Contents Precautions and safety reg
Page 32 and 33: 32 Precautions and safety regulatio
Page 34 and 35: 34 MODUCONTROL default settings USE
Page 36 and 37: 36 User interface and parameter vis
Page 40 and 41: 40 Index - String Index - String In
Page 42 and 43: To access the INSTALLER menu, press
Page 44 and 45: 44 Index - String Index - String In
Page 46 and 47: j Parameters visible in the heat pu
Page 48 and 49: To access the ELECTRIC HEATER menu,
Page 50 and 51: Apart from the parameters that can
Page 52 and 53: The units have two types of malfunc
Page 54 and 55: 54 32 132 Excessive temperature of
Page 56 and 57: Table des matières Précautions et
Page 58 and 59: 58 Précautions et normes de sécur
Page 60 and 61: 60 Réglages par défaut de MODUCON
Page 62 and 63: L’interface utilisateur principal
Page 64 and 65: Pour entrer dans le menu UTILISA- T
Page 66 and 67: 66 Index - chaîne Index - chaîne
Page 68 and 69: Pour entrer dans le menu INSTALLA-
Page 70 and 71: 70 Index - chaîne Index - chaîne
Page 72 and 73: j Paramètres visibles dans les mod
Page 74 and 75: Pour entrer dans le menu RÉSISTANC
Page 76 and 77: En plus des paramètres pouvant êt
Page 78 and 79: Les unités prévoient deux typolog
Page 80 and 81: 80 30 130 Communication absente La
Page 82 and 83: Index Vorsichtsmaßnahmen und Siche
Page 84 and 85: 84 Vorsichtsmaßnahmen und Sicherhe
Page 86 and 87: 86 Defaulteinstellungen MODU CONTRO
Page 88 and 89:
Anzeigen der Benutzerschnittstelle
Page 90 and 91:
Für den Zugriff auf das ANWENDER-M
Page 92 and 93:
92 Index - String Index - String In
Page 94 and 95:
Für den Zugriff auf das INSTALLATE
Page 96 and 97:
96 Einstellung des Frostschutz-/Int
Page 98 and 99:
j Bei den Modellen mit Wärmepumpe
Page 100 and 101:
100 Menü für die Einstellung der
Page 102 and 103:
Neben den über die Bedientafel ein
Page 104 and 105:
Bei den Geräten sind 2 Typen von S
Page 106 and 107:
106 30 130 Keine Verbindung vorhand
Page 108 and 109:
Índice Precauciones y normas de se
Page 110 and 111:
110 Precauciones y normas de seguri
Page 112 and 113:
112 Configuraciones por defecto MOD
Page 114 and 115:
114 La interfaz usuario principal e
Page 116 and 117:
116 Para ingresar al menú USUARIO
Page 118 and 119:
118 Índice - línea Índice - lín
Page 120 and 121:
120 Para ingresar al menú INSTALAD
Page 122 and 123:
122 Índice - línea Índice - lín
Page 124 and 125:
124 Índice - línea j Índice - l
Page 126 and 127:
126 Para ingresar al menú RESISTEN
Page 128 and 129:
128 Además de los parámetros que
Page 130 and 131:
130 Las unidades prevén dos tipolo
Page 132:
132 31 131 PFC Module Error del mó
show all

MODUCONTROL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?