liberty-automatic-grinder-pump--lsg202-lsg203-lsg204-manual.pdf

More documents

Recommendations

Info

Table of Contents SECTION 1 GENERAL INFORMATION------------------------------------------------------------------------------ 3 SECTION 2 INTRODUCTION-------------------------------------------------------------------------------------------- 4 SECTION 3 MECHANICAL INSTALLATION ----------------------------------------------------------------------- 4-6 SECTION 4 ELECTRICAL CONNECTION-------------------------------------------------------------------------- 6-8 SECTION 5 OPERATION ------------------------------------------------------------------------------------------------ 9 TROUBLESHOOTING CHART ------------------------------------------------------------------------ 10 PANEL INSTALLATION SHEET----------------------------------------------------------------------- 11 TYPICAL INSTALLATION DRAWING-----------------------------------------------------------------12 PERFORMANCE CURVE------------------------------------------------------------------------------- 13 SECTION 6 WARRANTY------------------------------------------------------------------------------------------------- 14 ©Copyright 2010 Liberty Pumps Inc. All rights reserved - 2 -
1. General Information Before installation, read the following instructions carefully. Each Liberty pump is individually factory tested to insure proper performance. Closely following these instructions will eliminate potential operating problems, assuring years of trouble-free service. � Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments. � The electrical connections and wiring for a pump installation should only be made by qualified personnel. � This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle. � DO NOT bypass grounding wires or remove ground prong from attachment plugs. � DO NOT use an extension cord. � This pump requires a separate, properly fused and grounded branch circuit. Make sure the power source is properly sized for the voltage and amperage requirements of the pump, as noted on the nameplate. � The electrical outlet shall be within the length limitations of the pump power cord, and at least 4 feet above floor level to minimize possible hazards from flood conditions. � The installation must be in accordance with the National Electric Code, Uniform Plumbing Code, International Plumbing Code, as well as all applicable local codes and ordinances. � Sump and sewage pumps often handle materials which could cause illness or disease. Wear adequate protective clothing when working on a used pump or piping. � Never enter a pump basin after it has been used. Sewage and effluent can emit several gases which are poisonous. � Keep clear of suction and discharge openings. To prevent injury, never insert fingers into pump while it is plugged in. � DO NOT use this product for flammable or corrosive liquid. � DO NOT use this product in applications where human contact with the pumped fluid is common (such as swimming pools, fountains, etc.) � NEVER dispose of materials such as paint thinner or other chemicals down drains, as they can chemically attack and damage pump components, potentially causing product malfunction or failure. � Do not use these pumps in water over 140� F. � The Uniform Plumbing Code (UPC) states that sewage systems shall have an audio and visual alarm that signals a malfunction of the system, to reduce the potential for property damage. Model HP Volts Pha se Full Load Amps FNPT Discharge Automatic or Manual* LSG202A 2 208/230 1 15 1.25” Automatic LSG202M 2 208/230 1 15 1.25” Manual LSG202M-C 2 208/230 1 15 1.25” Manual LSG203M 2 208/230 3 10.6 1.25” Manual LSG204M 2 440/460 3 5.3 1.25” Manual LSG205M 2 575 3 4.9 1.25” Manual LSGX202A 2 208-230 1 15 1.25” Automatic LSGX202M 2 208-230 1 15 1.25” Manual LSGX202M-C 2 208-230 1 15 1.25” Manual LSGX203M 2 208/230 3 10.6 1.25” Manual LSGX204M 2 440/460 3 5.3 1.25” Manual LSGX205M 2 575 3 4.9 1.25” Manual � Note: Manual models (“M” suffix), require a separate approved pump control device or panel for automatic operation. Operation of these models will be according to the control selected. Make sure the electrical specifications of the control selected properly match the electrical specifications of the pump. Always refer to control panel instructions for proper installation. Model ("M-C" suffix) require external capacitors and relay. (Order kit K001316) start cap - 200-240, 220V or 216 – 259 uf, 250V run cap - 50 uf, 370V Mars Potential Relay 19551 (#551) pick up 244V – 270V drop out of 40V-90V ©Copyright 2010 Liberty Pumps Inc. All rights reserved - 3 -
Page 1: Installation Manual 5647000H Omnivo
Page 5 and 6: 3-2 STORAGE BEFORE USE Liberty pump
Page 7 and 8: 4-3 CONTROL PANEL OPERATION 4-4 EXT
Page 9 and 10: 5. 5-1 OPERATION Operation After th
Page 11 and 12: FIGURE 2 CONTROL PANEL INSTALLATION
Page 13 and 14: HEAD (FEET) 200 190 180 170 160 150
Page 15 and 16: Manuel d’installation 5647000H Po
Page 17 and 18: 1. Renseignements généraux Lire a
Page 19 and 20: 3-2 ENTREPOSAGE AVANT UTILISATION L
Page 21 and 22: 1. La pompe peut fonctionner avec u
Page 23 and 24: 5. 5-1 FONCTIONNEMENT Fonctionnemen
Page 25 and 26: FIGURE 2 INSTALLATION DU PANNEAU DE
Page 27 and 28: ÉLÉVATION HEAD (FEET) (EN PIEDS)
Page 29 and 30: Manual de instalación 5647000H Bom
Page 31 and 32: 1. Información general Lea con ate
Page 33 and 34: LA BOMBA NUNCA SE DEBERÁ ALMACENAR
Page 35 and 36: 1. La bomba funciona con una tensi
Page 37 and 38: COMPRUEBE SIEMPRE QUE NO HAYA CABLE
Page 39 and 40: FIGURA 2 INSTALACIÓN DEL PANEL DE
Page 41 and 42: ALTURA HEAD (PIES) (FEET) 200 190 1

liberty-automatic-grinder-pump--lsg202-lsg203-lsg204-manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?