RGP 130-16 E - Protool GmbH

More documents

Recommendations

Info

the new brush and secure the in the holes by turning them clockwise – see figure [4 a]. Deflecting the springs from vertical direction does not constitute a defect. Then remove the brush with fitted springs, attach them on the cover [4-3] from the front end and tilt them – see figure [4 b]. Make sure that the springs in the cover fit into the guiding holes and screw back the screws with washers [4-2]. 7.6 Grinding wheel Depending on the application area, various grinding wheels are available – see table on page 16. Use solely wheels of PROTOOL trademark, which guarantees the grinding output of the machine. 8 Maintenance - Wrapped electric tools can be stored in a dry place without heating, with temperatures not lower than −5 °C. Unwrapped electric tools can only be stored in dry places with temperatures not lower than +5 °C, without sudden changes in the temperature. WARNING Always remove the plug from wall socket each time the machine maintenance is carried out! - To ensure the airflow is sufficient, cooling openings of the motor must be always clean and free. - The machine is equipped with special selfdisconnecting brushes. When the brushes are worn, the power supply is automatically disconnected, and the machine is stopped. 10 Declaration of Conformity Reinstating grinder Serial no. RGP 130-16 E 767701 We declare under our sole responsibility that this product is in conformity with the following standards or standardization documents: EN ISO 12 100, EN 55 014-1, EN 55 014-2, EN 60 745-1, EN 60 745-2-3, EN 61 000-3-2, EN 61 000-3-3 according to the provision of the regulations stipulated in Directive 2006/42/EC, 2004/108/EC, 2011/65/EU. Festool Group GmbH & Co. KG Wertstr. 20, D-73240 Wendlingen, Germany Dr. Martin Zimmer Head of Research, Development and Technical Documentation 25.01.2013 WARNING To maintain the protection level, the device must be checked in specialized electro technical workshop, which is authorized for such work and they will inspect the safety of the device. - Service – see enclosed sheet. 9 Environmental Protection / Disposal Power tools, accessories and packaging should be sorted for environmental-friendly recycling. Only for EC countries: Do not dispose of power tools into household waste! According to the European Directive 2002/96/EC on waste electrical and electronic equipment and its incorporation into national law, power tools that are no longer suitable for use must be separately collected and sent for recovery in an environmental-friendly manner. Information on REACh http://www.tts-protool.com/reach 15
11 The table with recommended types of grinding wheels Grinding wheel Application Electronic adjusting wheel DIA STONE-RGP 130 Very hard materials, such as concrete with hardness over C20, cast concrete 6. DIA HARD-RGP 130 Very hard materials, such as concrete with hardness over C10, hard paints 6. DIA ABRASIV-RGP 130 Soft materials with higher abrasion, such as fresh concrete, tiling glue, hard plaster, sandstone 6. DIA UNI-RGP 130 Multipurpose use, such as paints (on concrete, plaster, wood, glue, hard plaster) 4. – 6. DIA THERMO-RGP 130 Tenacious and thermo-elastic materials, such as paints, protective paints, elastic glue 5. – 6. 16
Page 1 and 2: RGP 130-16 E
Page 5 and 6: D Sanierungsschleifer RGP 130-16 E
Page 7 and 8: 6 am Festsetzpunkt bewirkt. Beispie
Page 9 and 10: 6.1 Ein- und Ausschalten Den Arreti
Page 11 and 12: 11 Tabelle der empfohlenen Schleifs
Page 13 and 14: must be suitable for fixing to the
Page 15: Declared total value of vibrations
Page 19 and 20: qu’il soit possible d’attacher
Page 21 and 22: ► Avant toute utilisation, contr
Page 23 and 24: 9 Instructions de protection de l
Page 25 and 26: namiento seguro de la herramienta.
Page 27 and 28: emplear únicamente cables de prolo
Page 29 and 30: 9 Protección del medio ambiente /
Page 31 and 32: sull’attrezzo. L’accessorio che
Page 33 and 34: zione e le cuffie per la protezione
Page 35 and 36: sui rifiuti di apparecchiature elet
Page 37 and 38: gebruikt. d) Het nominale toerental
Page 39 and 40: gebreken door een vakbekwame servic
Page 41 and 42: 9 Milieubescherming / Afvalverwijde
Page 43 and 44: sätt. f) Fästmåtten för skivan,
Page 45 and 46: närt fastställande av vibrationse
Page 47 and 48: 11 Tabell för rekommenderade typer
Page 49 and 50: lismittoja. Väärän kokoista lis
Page 51 and 52: Ilmoitettu tärinän kokonaisarvo o
Page 53 and 54: 11 Hiomalaikkojen suositeltujen tyy
Page 55 and 56: tilstrækkeligt beskyttet og heller
Page 57 and 58: Omdrejningshastigheden afhænger af
Page 59 and 60: 11 Tabel over anbefalede slibeskive
Page 61 and 62: nominelle omfanget av deres elektro
Page 63 and 64: Lydstyrkenivå: 106 dB (A) Unøyakt
Page 65 and 66: 11 Tabelle over anbefalte typer på
Page 67 and 68:
que ser pelo menos iguais às rota
Page 69 and 70:
► Antes de cada uso, controle o e
Page 71 and 72:
ADVERTÊNCIA Para manter a cobertur
Page 73 and 74:
RUS Заглаживающая шл
Page 75 and 76:
Могло бы произойти
Page 77 and 78:
6 Ввод в эксплуатац
Page 79 and 80:
11 Таблица рекоменд
Page 81 and 82:
sahu pro vaše elektromechanické n
Page 83 and 84:
5.8 Hlučnost a vibrace POZOR Hluk
Page 85 and 86:
10 Tabulka doporučených typů bro
Page 87 and 88:
automatycznie jego bezpiecznego uż
Page 89 and 90:
► Przed każdym użyciem narzędz
Page 91 and 92:
9 Ochrona środowiska / Usuwanie od
Page 93 and 94:
ozsahu pre vaše elektromechanické
Page 95 and 96:
16 rokov. 5.8 Hlučnosť a vibráci
Page 97:
11 Tabuľka odporúčaných typov b
show all

RGP 130-16 E - Protool GmbH

Create successful ePaper yourself

Delete template?

Save as template?