You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Serie</strong> 08.250.<br />
<strong>Mt</strong> 30 K<strong>Nm</strong><br />
<strong>Serie</strong> /<strong>Serie</strong>s 08.250.- - 0 08.250.- - 1<br />
<strong>Mt</strong> (1) K<strong>Nm</strong> 30 30<br />
<strong>Mt</strong>M (2) K<strong>Nm</strong> 40 40<br />
<strong>Mt</strong>W (3) K<strong>Nm</strong> 18 18<br />
ß° (4) 15 15<br />
A 250 285<br />
B H7 140 175<br />
D 18 20<br />
F +0,2 6 7<br />
G 250 250<br />
H B12 18 20<br />
I ±0,1 218 245<br />
N° Fori / Holes 8 8<br />
N 125 125<br />
P (DIN 5480) 100x3x32 100x3x32<br />
T 160x10 160x10<br />
FLANGIA DIN / DIN FLANGE<br />
Allungabile con tubo di prolunga<br />
Sliding with tube<br />
Cod./Code<br />
08.250.400<br />
08.250.401<br />
Flangia/Flange DIN 250 DIN 285<br />
L (5) +All 860+110<br />
L (5) +All 860+110<br />
Fissa con tubo di prolunga<br />
Fixed with tube<br />
08.250.500<br />
08.250.501<br />
L (5) 610<br />
L (5) 610<br />
Extracorta<br />
Extra short<br />
Giunto semplice<br />
Simple joint<br />
08.250.600<br />
08.250.601<br />
08.250.100<br />
08.250.101<br />
L MIN +All (6) 700+60<br />
L MAX +All (6) 855+110<br />
L MIN +All (6) 700+60<br />
L MAX +All (6) 855+110<br />
L 250<br />
L 250<br />
Giunto doppio<br />
Double joint<br />
08.250.200<br />
08.250.201<br />
L 500<br />
L 500<br />
(1) Momento torcente a catalogo.<br />
(2) Momento torcente massimo ammissibile, con frequenza limitata,<br />
senza deformazioni permanenti.<br />
(3) Momento torcente massimo a fatica alterna.<br />
(4) Angolo massimo di inclinazione per giunto.<br />
(5) Lunghezza minima, lunghezze superiori a richiesta.<br />
(6) Lunghezze minime e massime, differenti a richiesta.<br />
Qualora figurino due alternative, se non espressamente richiesto,<br />
verrà fornita la prima delle due.<br />
(1) Torque as catalogue.<br />
(2) Maximum admissible torque, with low-frequency, without permanent<br />
bucklings.<br />
(3) Maximum torque with alternate load.<br />
(4) Maximum angle of inclination per joint.<br />
(5) Minimum length, longer lengths on request.<br />
(6) Minimum and maximum closed lengths, different lengths on request.<br />
When there are two alternatives, if not explicity required, we'll supply the first<br />
one.<br />
52