BASIC 8T/D - Svh24

Appliance description (pic. 1)
1. Handle
2. Splitting knife
3. Clamping plate
4. Service arm
5. Handle covering
6. Table holder (in front)
7. Table blocking
8. Splitter table
9. Wheels
10. Switch / plug
11. Lift adjusting rod
12. Table holder (side)
Appliance
BASIC 8T/D WOOD SPLITTER
Robust design, splitting knife out of special steel, all steel parts
with high-quality powder coating, high-quality hydraulic pump.
Engine with overheating fuse.
Use as designated
The log splitter has exclusively been designed to split wood
along fibres. Installation, maintenance, repair, etc. instructions
must strictly be followed to prevent risks and damage.When
splitting, it is necessary to make sure the split wood is only
fitted on the grooved sheet of the supporting plate or on the
grooved sheet of the splitter table.
The machine cannot be used for works other than for which
the machine has been designed and that are specified in the
Operating Instructions. Any other use is a use in conflict with
the designation. The manufacturer will not be liable for any
consequential damage and injuries. Please be sure to know
that the machine has not been designed for industrial
purposes.
Guarantee
Warranty period of 12 months applies to commercial use and
24 months applies to private use and commences on the day
of purchase of the device.
Warranty applies exclusively to failures due to defective
material or workmanship. An original sale slip with indication of
date of sale must be presented in case of claiming for the
warranty rights.
Warranty does not cover unprofessional use such as device
overload, violent use, damage caused by third party or foreign
materials, failure to comply with operations and assembly
manual, and normal wear and tear.
Technical data
Technical data:
Basic 8T/D
Connector:
400 V~50 Hz
Engine power: 3,6 kW P1/ S6 40%
Engine revolutions:
1400 revolutions a minute
Max. splitting force:
8 tons
Max. splitting lift:
460 mm
Forward feed rate:
4-5 cm/s
Backward feed rate:
10-12 cm/s
Hydraulic oil tank: 6 l (oil type HLP 46)
Max. log length:
570 / 770 / 1060 mm
Max. diameter of split wood: App. 400 mm
Splitter’s post:
120 mm x 120 mm
Table dimensions:
App. 360 x 280 mm
Weight:
115 kg
Order No. 02025
Safety instructions
General
For safety reasons it is necessary to respect and follow safety
instructions specified in these Operating Instructions and
instructions on the appliance relating to appliance operation,
maintenance and repairs.
Operating staff
Using the wood splitter can be associated with some
risks. Therefore only trained and experienced persons can
handle the appliance and work with it. The operating staff
must wear tight, close-fitting clothing and protective
shoes.
Caution: When splitting, dry and mature wood may
get intensely shot out and injure the face of the operator.
Please wear appropriate protective clothing!
Workplace
To ensure safe wood splitting, it is necessary that the
workplace is flat and enables stability keeping and sufficient
free moving. All obstacles need to be removed from access
paths when bringing the splitter and taking it away. Sufficient
workplace lighting must be ensured.
Make sure no persons are present in the workplace
during appliance operation or make sure they keep a
sufficient safe distance.
The log splitter has been designed to be operated by 1
person. Two or more persons must never work with the
appliance.
Work preparation
Current supply needs to be interrupted by pressing the red
button on the switch and disconnecting the plug at any repairs
or maintenance work and when leaving the wood splitter.
Interrupting the current supply by putting the switch to
OFF position is not sufficient. GÜDE wood splitters are
fundamentally supplied with hardened splitting knives.
However, if you detect any slight deformation of the knife edge
after splitting wood containing any invisible foreign particles,
e.g. out of concrete, steel, etc. then remove it by a file or
grinding off. Keeping the splitting knife permanently sharp
increases the working output.
TIP: Occasionally grease the splitting knife with fat (for
problem wood).
The function of safety equipment (especially the twolever
operation) needs to be checked before the splitter is
put into operation for the first time.
ATTENTION! Make sure the splitting table is safely
secured to the splitter before the splitter is put into
operation.
Disposal
The disposal instructions are based on icons placed on the
machine or its package. The description of the meanings can
be found in the “Marking“ section.
Transport package disposal
The package protects the machine against damage during
transport. Packing materials are usually chosen depending on
their environmental friendliness and disposal method and can
therefore be recycled. Returning the package to material
circulation saves raw materials and reduces waste disposal
costs. Parts of packages (e.g. foils, styropor®) can be
dangerous to children. Risk of suffocation! Keep parts of the
package away from children and dispose them as soon as
possible.
10