Zip Aquapoint III 5-15Ltr Spec Sheet - Advancedwater.co.uk

Zip Aquapoint III Water heatersUnvented, single or multiple outlets5.0 litre, 10.0 litre, 15.0 litreDimensions (mm)Weight (kg)H W D Empty FullZip Aquapoint III AP3/05 5.0 litre 376 256 260 6.7 12.7Zip Aquapoint III AP3/10 10.0 litre 480 350 265 8.5 18.5Zip Aquapoint III AP3/15 15.0 litre 480 350 310 9.8 24.8• Unvented, multipoint water heater• Hot water storage tank of 1.8mm thick glassenamelled steel tested to 12 bar. 2.0 kWheating element• Fitted with a sacrificial anode. Adjustablethermostat with a range up to 75ºC• Fitted with frost protection• Resettable over temperature safety cut out• Element ‘ON’ neon indicator• High density CFC-free polyurethanefoam insulation• Corrosion resistant white plastic case• BSP water connections• Supplied with installation kitCapacity5 litres, 10 litres, 15 litresRating2.0 kWHeating elementEmbedded rod typeThermostatCapillary type adjustable up to 7ºC to 75ºCWater tank1.8mm glass enamelled, steel tested to 12 bar,with a working pressure of 3.5-4 barCaseHigh impact and corrosion resistantwhite plasticInsulationHigh density, CFC-free polyurethane foamSafety featuresa) manually resettable thermal cutout set to85ºC +/– 3ºCb) expansion relief valve (supplied) set at 6 barc) protected against frost whilst power is ond) sacrificial anode for added protectionagainst corrosion for element and tank – mustbe checked regularly (6 months) and replacedwhere necessary as gradual erosion will occur.In extreme cases local water conditions cancause rapid erosion of the anode resulting inparticles being deposited as a residueThe Aquapoint should not be used where waterquality is criticalApprovalsWRAS approved and CE endorsedWarranty12 monthsInstallationLocationThe water heaters should be installed on thefloor, provided connections are at the topAll models can supply one outlet or multipleoutlets with no special taps requiredWhen deciding the final location of the heater,consideration should be given to the safe andvisible disposal of any water resulting fromleaks or seepage. This is particularly relevantwhen the heater is located in a roof space,cupboard or any concealed locationPlumbingWater connections 15mm BSPMinimum recommended water pressure 1 barPressure relief valve set at 6 barPressure and temperature relief valve, wherefitted requires plumbing to waste in accordancewith water byelawsElectricalTo be wired to a double pole fused spur,minimum break rating 13 ampsInstallation must comply with currentIEE regulationsCautionVariable temperature water heaters should beset only in strict compliance with regulationsgoverning the temperature of stored anddispensed hot waterTypical installationPerformanceDiagram 1.Inlet pressure less than 4 barand expanded hot water can beaccommodated in the pipe workMinimum length of pipe – Length ‘A’Size 15mm pipe 22mm pipe5 litres 1.2m (4ft) 0.6m (2ft)10 litres 2.7m (9ft) 1.2m (4ft)15 litres 4.2m (14ft) 1.8m (6ft)Model Heat up time Re-heat time(15° to 65ºC) (70% vol.)AP3/05 11 mins 7 minsAP3/10 18 mins 12 minsAP3/15 32 mins 18 minsDiagram 2.Inlet pressure less than 4 bar but expanded hotwater cannot be accommodated in the pipework. (Using pack AQ2 expansion vessel andcheck valve)Diagram 3.Inlet pressure greater than 4 bar and expanded hotwater cannot be accommodated in the pipe work.(Using pack AQ2 and AQ3 expansion vessel, checkvalve and pressure reducing valve)15.09.09Zip Heaters (UK) Ltd. 14 Bertie Ward Way, Dereham, Norfolk NR19 1TETel 0845 602 4533 Fax 01362 692448 sales@zipheaters.co.uk www.zipheaters.co.uk