Bandslipmaskin Belt Grinding Machine BBD 150 20645-0108

More documents

Recommendations

Info

GETTING TO KNOW YOUR BELT & DISC SANDER WARNING! To avoid injury from accidental start, remove the plug from power source outlet before making any adjustments.. 1. Hex socket head screw. Loosening screw allows belt bed to raise to the vertical position. 2. Tracking knob. Turning knob counterclockwise causes sanding belt to move towards the disc; otherwise to move away from the disc. 3. Sanding belt. 4.Tension lever. Sliding lever to the right releases the sanding belt tension; sliding lever to the left applies belt tension. 5. Work support hex screw. 6. Work support. Supports the workpiece on the sanding belt. 7. Base 8. <strong>Belt</strong> bed 9. Mounting holes 10. No-volt switch 11. Sanding disc 12. Sanding paper 13. Work table assembly 42 NO-VOLT SWITCH NOTE: The no-volt switch has no-volt release and emergency stop feature. This feature is intended to prevent the unauthorized starting. 1. To turn machine “on”, raise the “emergency stop cover” up, and push the green button (with “I” symbol) about 1 second.
2. To turn machine “off”, just need push the “emergency stop cover” down. The emergency stop cover can located on the stop position. 3. Any time when you need to stop the machine, easy to push the emergency stop cover down. BASIC OPERATION Before using the sander WARNING! To avoid mistakes that could cause serious, permanent injury, do not plug the sander in until the following steps are completed. 1. Assembly and alignment 2. Learn the use and function of no-volt switch. Backstop, belt tracking knob, belt tension lever, work table and work table tilt lock knob. 3. Review and understand all safety instructions and operating procedures in this manual. 4. Review of the maintenance methods for this sander. Before each use INSPECT YOUR SANDER CAUTION. Disconnect the sander. To avoid injury from accidental starting unplug the sander before changing the setup, sanding disc or belt or adjusting anything. Check damaged parts. Check for • alignment of moving parts • binding or moving parts • broken parts • work parts that cause a gap larger than 1/16” between work support and sanding surface • sanding belt narrower than 6 inches. Narrower belts uncover parts that could trap your fingers. • worn or damaged electric cords • stable mounting, and 43 • any other conditions that may affect the way the sander works. If any part is missing, bent, or broken in any way, or any electrical parts don’t work properly, turn the sander off and unplug the sander. REPLACE damaged, missing, or failed parts before using the sander again. MAINTAIN TOOLS WITH CARE. Keep the sander clean for best and safer performance. Follow instructions for lubricating. REMOVE ADJUSTING KEYS AND WRENCHES from tool before turning it on. WARNING! To avoid injury from jams, slips or thrown pieces: • USE ONLY RECOMMENDED ACCESSORIES. Consult this owner’s manual for recommended accessories. Follow the instructions that come with the accessories. The use of improper accessories may cause risk of injury to person. • Adjust any work support to clear the sanding surface by no more than 1/16”. When checking clearance between the belt and work support, press the belt that against the metal beneath it. • Make sure all clamps locks are tight and no parts have excessive play. • Keep work area clean. Cluttered areas and benches invite accident. Floor must not be slippery. To avoid burns or other fire damage, never use the sander near flammable liquids, vaports or gases. PLAN AHEAD TO PROTECT YOUR EYES, HANDS, FACE, EARS. KNOW YOUR SANDER. Read and understand the owner’s manual and labels affixed to the tool. Lean its application and limitations as well as the specific potential hazards peculiar to the tool. To avoid injury from accidental contact with moving parts: • KEEP GUARDS IN PLACE and in working order. Don’t do layout, assembly, or setup work on the sander while any parts are moving. PLAN YOUR WORK USE THE RIGHT TOOL. Don’t force tool or attachment to do a job it was not designed to do. CAUTION: This machine is not designed for heavy deburring operations. When finishing metal, sparks or hot fragments could cause a fire. To avoid this: • Disconnet any dust collecting hose from the sander. • Remove all traces of wood dust from inside the sander. • Remove all traces of metal dust from inside the sander before sanding wood again. Dress for safety. • Any power sander can throw foreign objects into the eyes. This can cause permanent eye damage. Wear safety goggles. • Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts. • Wear nonslip footwear • Tie back long hair. • Noise levels vary widely. To avoid possible hearing damage, wear ear-plug or muffs when using sander for hours at a time. • Sanding operations are usually dusty. Wear a dust mask along with safety goggles.
Page 1: Bandslipmaskin Belt Grinding Machin
Page 4 and 5: PRH1 PRH2 PRH3 DK Advarselssymboler
Page 6 and 7: DANSK Oversættelse af den original
Page 8 and 9: Være passende påklædt. Alle vær
Page 10 and 11: 2. Hvis mellem bordet og skiven ikk
Page 12 and 13: 2. For at lukke for maskine du skal
Page 14 and 15: 3. Placer båndvangen vertikalt som
Page 16 and 17: Bemærk: For stor båndspænding p
Page 18 and 19: 18. ÄRA KUNAGI SEISA MASINA PEAL.
Page 20 and 21: NB! Et end masina käsitsemisel mit
Page 22 and 23: ÕPI OMA LINTLIHVMASINAT TUNDMA HOI
Page 24 and 25: • Lihvimistöö on tavaliselt tol
Page 26 and 27: VÄIKSEMATE OTSPINDADE LIHVIMINE LI
Page 28 and 29: SUOMI Käännös alkuperäisten ohj
Page 30 and 31: SUUNNITTELE MITEN SUOJAAT SILMÄT,
Page 32 and 33: Hiomapinta 2 mm max. Pöytä 7. Ruu
Page 34 and 35: 2. Koneen irtikytkemiseksi pitää
Page 36 and 37: PINNAN HIONTA HIOMALAIKALLA Varoitu
Page 38 and 39: 7. Ota vetopyörän suojus ja sijoi
Page 40 and 41: 19. CHECK DAMAGED PARTS. Before fur
Page 42 and 43: Sanding plate Disc guard Installing
Page 46 and 47: INSPECT YOUR WORKPIECE CAUTION! Mak
Page 48 and 49: WARNING! For your own safety, remov
Page 50 and 51: LIETUVIŠKAI Vertimas originali ins
Page 52 and 53: RAKTUS IR VERŽLĖRAKČIUS nuo darb
Page 54 and 55: poveržlę ir įstatykite rankeną
Page 56 and 57: ĮTEMPIMO PERTRAUKIKLIS Atsižvelki
Page 58 and 59: Perspėjimas: siekiant išvengti ap
Page 60 and 61: GEDIMŲ NUSTATYMAS Perspėjimas: sa
Page 62 and 63: 14. NEZAUDĒJIET LĪDZSVARU. Vienm
Page 64 and 65: 2. Nosakiet un atzīmējiet caurumu
Page 66 and 67: IEPAZĪŠANĀS AR SLĪPLENTES / SL
Page 68 and 69: • Nevalkājiet vaļīgu apģērbu
Page 70 and 71: MAZU GALA VIRSMU SLĪPĒŠANA UZ SL
Page 72 and 73: NORSK Oversettelse av den opprinnel
Page 74 and 75: LÆR DEG Å KJENNE DIN SLIPEMASKIN.
Page 76 and 77: Låseratt for bord Bruksanvisningen
Page 78 and 79: 2. For å slå av slipemaskinen, tr
Page 80 and 81: Pussebjelke Arbeidsstøtte “L”-
Page 82 and 83: 6. Kontroller hvor spent drivreimen
Page 84 and 85: 13. DOBRZE MOCOWAĆ OBRABIANY PRZED
Page 86 and 87: 3. Wywiercić w blacie cztery otwor
Page 88 and 89: ZAPOZNANIE SIĘ ZE SZLIFIERKĄ Uwag
Page 90 and 91: • Nie używać luźnej odzieży,
Page 92 and 93: uraz. Obrabiany przedmiot Środek K
Page 94 and 95:
SVENSKA Översättning av ursprungl
Page 96 and 97:
PLANERA I FÖRVÄG FÖR HUR DU SKA
Page 98 and 99:
Slipyta Låsratt för bord: 2 mm sp
Page 100 and 101:
2. För att stänga av slipmaskinen
Page 102 and 103:
Putsbalk “L”-sexkantsnyckel Arb
Page 104 and 105:
6. Kontrollera hur spänd drivremme
Page 106 and 107:
104
Page 108 and 109:
Fax.nr des Herstellers / Producente
Page 110:
Produsentens navn, adresse, tlf/fax
show all

Bandslipmaskin Belt Grinding Machine BBD 150 20645-0108

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?