PIR Sensor & Microwave Sensor LX-PM-101 ... - Lexing.com.cn

-FunctionTIME+Time settingThe light can be set to stay ON for any period oftime between approx.10sec(turn fully anticlockwise)and a maximum of 20min(turn fully clockwise). Anymovement detected before this time elapse willre-start the timer. It is recommended to select theshortest time for adjusting the detection zone andfor performing the walk test.NOTE: after the light switches OFF, it takes approx.1sec before it is able to start detecting movementagain.The light will only switch on in response tomovement once this period has elapsed.Functional knobWorking indicator lightDaylighting devicesIt is mainly for the adjustment of the delay timefrom the moment the signal detected and lightauto-on till the light auto-off. You can define thedelay time to your practical need. But you’dbetter lower the delay time for the sake ofenergy saving, since the microwave sensor hasthe function of continuous sensing, that is, anymovement detected before the delay timeelapses will re-start the timer and the light willkeep on only if there is human in the detectionrange.HF SensorRemote signal receiverPower 220V/AC-+SENSDetection range setting (sensitivity)Detection range is the term used to describe theradii of the more or less circular detection zoneproduced on the ground after mounting the sensorlight at a height of 2.5m, turn the reach control fullyanticlockwise to select minimum reach (approx.2mradii), and fully clockwise to select maximum reach(approx. 15m radii).NOTE: the above detection distance is gained inthe case of a person who is between 1.6m~1.7mtall with middle figure and moves at a speed of0.6~1.5m/sec. if person’s stature, figure andmoving speed change, the detection distance willalso change.3PCS PIR SensorElectric productsElectric productsElectric productsFUSEThe total power of incandescent lamp can not exceed 2000WThe total power of CFL can not exceed 800WThe detection distance may multiply for the reflection on microwave electromagnetic field by the metal or glassmaterials. Thus, lower the sensitivity to reach the appropriate detection distance. Never turn the SENS knob to themaximum value to avoid error detection. Also the surrounding environment will lead to error action, e.g. the automobilespassing by or the wandering objects caused by the wind. Products should be installed more than 4 meters one from theother, otherwise the interference among them will cause error action.Light-control settingThe chosen light response threshold can be infinitely from approx. 2-2000lux. Turn it fully anti-clockwise to select dusk- to-dawnoperation at about 2 lux. Turn it fully clockwise to select daylight operation at about 2000lux. The knob must be turned fullyclockwise when adjusting the detection zone and performing the walk test in daylight.LUXNote: please don’t adjust the three functional buttons to excess. That is because the three functional buttons were connected tothe components directly, there is a small stopper in each of the threecomponents, when you adjust the buttons from start to end, the excessive turn will damage the stopper,and lead to the360°non-stop turn around. Theadjust range limit is 270°, please do pay attention to this.PIR & Micrwoave sensor functionFunctional knobChoosing by the button:• Press the button one time, can choose microwave sensormode, pir senosr mode, microwave sensor & pir sensor twofuntions together mode in turn.• Choosing microwave sensor mode, after the green ledindicator light flash 4 times, then the product into the microwave Led indicatorsensor working state;Choosing pir sensor mode, after the redled indicator light flas 4 times,then the product into the pir Green Redsensor working state.• Choosing the microwave sensor & pir sensor two funtions together mode, the green led indicator lights flash4 times, then the red led indicator flash 4 times, and then the product into the microwave sensor & pir sensortwo funtions together mode working state.