YAMAHA P-155

MIDI Data Format / ормат MIDI-данных / Format des données MIDI / Formato de datos MIDI(2) Universal Non-Realtime Message (GM On)General MIDI Mode OnData format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->[F7H]F0H = Exclusive status7EH = Universal Non-Realtime7FH = ID of target device09H = Sub-ID #1=General MIDI Message01H = Sub-ID #2=General MIDI OnF7H = End of ExclusiveorF0H = Exclusive status7EH = Universal Non-RealtimeXnH = When received, n=0–F.X = irrelevant09H = Sub-ID #1=General MIDI Message01H = Sub-ID #2=General MIDI OnF7H = End of ExclusiveWhen a General MIDI mode ON message is received, theMIDI system will be reset to its default settings.This message requires approximately 50ms to execute, sosufficient time should be allowed before the next message issent.9. SYSTEM EXCLUSIVE MESSAGES (XG Standard)(1) XG Native Parameter ChangeData format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->[mmH] -> [llH] -> [ddH] ->...-> [F7H]F0H = Exclusive status43H = YAMAHA ID1nH = When received, n=0–F.When transmitted, n=0.4CH = Model ID of XGhhH = Address HighmmH = Address MidllH = Address LowddH = Data|F7H = End of ExclusiveData size must match parameter size (2 or 4 bytes).When an XG System On message is received, the MIDI systemwill be reset to its default settings.The message requires approximately 50ms to execute, sosufficient time should be allowed before the next message issent.(2) XG Native Bulk Data (reception only)Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->[ccH] -> [F7H]F0H = Exclusive status43H = YAMAHA ID0nH = When received, n=0–F.When transmitted, n=0.4CH = Model ID of XGaaH = Byte CountbbH = Byte CounthhH = Address HighmmH = Address MidllH = Address LowddH = Data| || |ccH = Check sumF7H = End of Exclusive• Receipt of the XG SYSTEM ON message causes reinitializationof relevant parameters and Control Change values. Allowsufficient time for processing to execute (about 50 msec)before sending the instrument another message.• XG Native Parameter Change message may contain two orfour bytes of parameter data (depending on the parametersize).• For information about the Address and Byte Count values,refer to Table 1 below. Note that the table’s Total Size valuegives the size of a bulk block. Only the top address of theblock (00H, 00H, 00H) is valid as a bulk data address.10. SYSTEM EXCLUSIVE MESSAGES(P-155 MIDI Format)Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [nnH] -> [F7H]F0H = Exclusive status43H = Yamaha ID73H = P-155 ID01H = Product ID (CLP common)nnH = Substatusnn Control02H Internal MIDI clock03H External MIDI clockF7H = End of Exclusive11. SYSTEM EXCLUSIVE MESSAGES (Others)Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]-> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H]Master Tuning (XG and last message priority) simultaneouslychanges the pitch of all channels.F0H = Exclusive Status43H = Yamaha ID1nH = When received, n=0–F.When transmitted, n=0.27H = Model ID of TG10030H = Sub ID00H =00H =mmH = Master Tune MSBllH = Master Tune LSBccH = irrelevant (under 7FH)F7H = End of Exclusive64P-155 Owner’s Manual / уководство пользователя / Mode d’emploi / Manual de instrucciones