Composites Turkey - Kompozit Sanayicileri DerneÄi
Composites Turkey - Kompozit Sanayicileri DerneÄi
Composites Turkey - Kompozit Sanayicileri DerneÄi
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
47<br />
şullarının varlığını ve koşulların sürdürülebilirliğinin tespiti<br />
yanında, kalite yönetim sisteminin ve yetkin personel istihdam<br />
edildiğinin tespitini de kapsamaktadır.<br />
Akreditasyon için yerine getirilmesi gereken diğer bazı<br />
gereklilikler aşağıda belirtildiği gibidir;<br />
• Gerçekleştirilen kalibrasyon/deneyler, müşterilerin ihtiyaçlarını<br />
karşılayabilen ve uygulanacak deney/kalibrasyon<br />
metodlarına uygun yöntemler kullanılarak gerçekleştirilmelidir.<br />
• Laboratuvar, kalibrasyon/deneylerin doğru bir şekilde<br />
yapılması için gerekli cihazlara sahip olmalı ve cihazların<br />
kalibrasyonu için, Uluslararası Birimler Sistemi’ne (SI)<br />
göre izlenebilir olmasını sağlayacak bir kalibrasyon programı<br />
uygulamalıdır.<br />
• Laboratuvar, gerçekleştirilen kalibrasyon/deney faaliyetlerinin<br />
geçerliliğinin izlenmesi amacıyla karşılaştırma<br />
ölçümlerine veya yeterlilik deney programlarına katılmalıdır.<br />
• Laboratuvar tarafından yapılan kalibrasyon/deney<br />
sonuçları, doğru, açık, kesin ve tarafsız olarak uygun bir<br />
şekilde rapor haline getirilmelidir.<br />
Bu kapsamda TÜRKAK tarafından Subor laboratuvarında<br />
rijitlik testi (Stiffness) için TS EN 1228/ISO 7685, çember<br />
çekme dayanım testi için TS EN 1394/ISO 8521 ve<br />
eksenel çekme dayanım testi için TS EN 1393/ISO 8513<br />
deney metodları baz alınarak değerlendirmeler yapılmış<br />
ve laboratuvar akredite edilmiştir.<br />
At Subor, tests are performed in<br />
accredited laboratories.<br />
Subor GRP Pipes are designed and<br />
tested in compliance with the world’s fundamental<br />
and acknowledged industry<br />
standards such as AWWA, ASTM, ISO, EN<br />
and BS as well as to meet the requirements<br />
of the national TSE standard. These standards<br />
define the initial design specifications<br />
and set out the product qualification and<br />
performance criteria.<br />
Some of the fundamental standards in<br />
using GRP pipe production are AWWA C<br />
950, ISO 10639, ISO 10467, EN 1796, EN<br />
14364, ASTM D 3262, ASTM D 3754, ASTM<br />
D 3517.<br />
During the production process, below<br />
control and performance tests that frequencies<br />
and methods based on the standards<br />
are performed to prove the mechanical performances<br />
of the products;<br />
- Stiffness Test<br />
- Failure Control at<br />
Inner Surface Under<br />
Load<br />
- Delamination Control<br />
Under Load<br />
- Axial Tensile Strength<br />
- Circumferential<br />
Tensile Strength<br />
The purpose of the<br />
aforesaid mechanical tests<br />
routinely performed are;<br />
stiffness measurements of<br />
the pipe under a defined<br />
deflection determined according<br />
to the standards,<br />
the lack of damages on<br />
the inner surfaces and<br />
delaminations under the<br />
enhanced deflection,<br />
measuring the minimum axial forces which<br />
is required per unit circumference of the<br />
pipe and determination of the minimum circumferential<br />
tensile strength per unit width<br />
value.<br />
Those mechanical tests are conducted<br />
in Subor’s Laboratories accredited by<br />
TURKAK in accordance with TS EN ISO/<br />
IEC 17025:2005 Test and Calibration Laboratories<br />
Qualification Standards.<br />
Subor laboratories are accredited to TS<br />
EN ISO/IEC 17025 standard that demonstrate<br />
to implement a management system,<br />
to be technically qualified including random<br />
sampling and to contain all the requirements<br />
of test and calibration laboratories<br />
to demonstrate production of the valid<br />
technical results. The main purpose of the<br />
standard that contains Laboratory Quality<br />
Management System and Laboratory Technical<br />
Terms is to ensure the reliability of the<br />
experiment, calibration and test results on<br />
behalf of clients.