Komponenten-Systeme | Components systemsKombirollen | Combined BearingsJustierbare KombirolleneinheitTyp JCfür alle Standard-ProfileVorteile:Spielfreiheit zwischen Rolleneinheit und Profil.Höhere Positioniergenauigkeit.Adjustable Combined Bearing unitType JCfor all standard profilesAdvantages:Min. clearance between bearing unit and profile.Higher positioning accuracy.Justierrolle zur oberen Laufflächemit einem Spiel von0,05 bis 0,1mm einstellenSet adjustable bearing to the top racewaywith a clearance of 0.05 to 0.1mmHauptlast auf KombirolleMain force on Combined BearingEinbau/EinstellungDie Einheit wird über die Flanschplatte angeschraubtDie Position der Justierrolle muß an der entgegengesetztenSeite der Last sein. Die Hauptlast soll auf dasRadiallager der Kombirolle eingeleitet werden.Das Justierlager wird eingestellt und anschließendgekontert.Vorsicht: Es dürfen keine großen Anpresskräfte auf dieJustierrolle kommen, sonst droht die Gefahrvon hohen Vorspannkräften die zu Profilbeschädigungenführen können.Tipp: Lassen Sie ein Spiel von 0,05 - 0,1 mm zwischenJustierrolle und Profil.Test: Der Führungswagen soll sich ohne großeLaufwiderstände bewegen können.CAD Download in 2D/3D unter www.winkel.deAssembly/AdjustingThe unit will be assembled by the flange plate.The position of the adjustable bearing must be at theload opposite side. The main forces should beon the radial bearing of the Combined Bearing.The adjustable bearing will be adjusted and finallysecured.Attention: Avoid giving too high pay loads to theadjustable bearing. (Risk of profile wear out.)Advice: Adjust the adjustable bearing with aclearance of 0.05 to 0.1 mm to the profile.Test: The carriage should run smoothly in the profilewithout big resistance.CAD download in 2D/3D at www.winkel.deTypTypeAABBCCDDFFGGHHIIJJKKLLMMNNOOJC 4.054JC 4.055JC 4.056JC 4.058JC 4.061JC 4.062JC 4.063140170170195240240265608080120120120150405050908080100±1±1±1±7±4±12±25M10M12M12M16M16M16M1662,470,078,078,0101,6101,6101,662,570,177,788,4107,7123,0149,0648282829898982433332829292930,536,036,544,055,056,058,5101515202020203040406060607572,083,583,590,0120,0120,0130,08010210215215015017040C = Dyn. Tragzahl Radiallager (ISO 281/1), CO = Stat. Tragzahl Radiallager (ISO 76), (Kombirolle)CA = Dyn. Tragzahl Axiallager (ISO 281/1), COA = Stat. Tragzahl Axiallager (ISO 76), (Kombirolle)FR = Tragzahl Radiallager zulässige Belastung zwischen Rolle und Profil,FA = Tragzahl Axiallager zulässige Belastung zwischen Rolle und Profil (Kombirolle)
Komponenten-Systeme | Components systemsKombirollen | Combined BearingsJustierrolle zumSpielausgleichAdjustablebearingHauptlast aufKombirolleMainforce oncombinedbearingLastLoadHauptlast aufKombirolleMainforce oncombinedbearingJustierrolle zum SpielausgleichAdjustable bearingSW 10/13spielarm einstellbar über Justierrolleplay free adjustment by usingadjustable bearingspielarm einstellbar überDistanzscheibenplay free adjustment by usingwashersKontermutter der JustierrolleLocking nutEinstellschraube mitKontermutter (beidseitig)Adjusting screwDistanzscheibeWasherProfile S. 52 | Profiles page 52SW 24/30SW 13Bestellbeispiel | Order exampleJC 4.054 [Kombirolle] Standard 0 [Profil] DS-0-0,5 [Distanzscheibe]JC 4.054 [Combined Bearing] Standard 0 [Profile] DS-0-0,5 [Washer type DS]TypTypeF R KNF R KNF A KNF A KNC KNC KNC O KNC O KNC A KNC A KNC OA KNC OA KNu/min max.r/pm max.Gewicht kgWeight kgProfileProfilesJC 4.054JC 4.055JC 4.056JC 4.058JC 4.061JC 4.062JC 4.0639,4011,3011,7220,4721,6830,9254,023,13,733,876,767,1610,217,831,045,548,068,081,0110,0151,035,551,056,872,095,0132,0192,011131823314368111418233650719009008007506505504501,652,953,35,88,759,7513,90 Nb1 Nb2 Nb3 Nb4 Nb5 Nb6 NbC = Dynamic load capacity radial bearing (ISO 281/1), CO = Static load capacity radial bearing (ISO 76), (Combined Bearing)CA = Dynamic load capacity axial bearing (ISO 281/1), COA = Static load capacity axial bearing (ISO 76), (Combined Bearing)FR = Load capacity radial bearing max. allowable force between bearing and profile, (Combined Bearing)FA = Load capacity axial bearing max. allowable force between bearing and profile, (Combined Bearing)41