Schnittdatenempfehlung <strong>VHM</strong> 217 HX63 Parameters recommendation, Paramètres conseillés, Parametri di taglio indicativi III Material Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 1200-1600 N/mm² 38-48 HRC Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 1200-1600 N/mm² 48-56 HRC Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 56-63 HRC D [mm] R [mm] V c [m/min] f z [mm] a p [mm] a e [mm] β [°] ø-eff [mm] n [min -1 ] V f [mm/min] 2 0,0 150 (130 - 170) 0,025 (0,005 - 0,045) 0,070 0,130 0 2,00 23.870 1.290 2 0,5 150 (130 - 170) 0,030 (0,010 - 0,050) 0,070 0,130 0 1,51 31.610 1.895 3 0,0 150 (130 - 170) 0,035 (0,015 - 0,055) 0,105 0,195 0 3,00 15.920 1.105 3 0,5 150 (130 - 170) 0,040 (0,020 - 0,060) 0,105 0,195 0 2,61 18.270 1.405 4 0,0 150 (130 - 170) 0,040 (0,020 - 0,060) 0,140 0,260 0 4,00 11.940 1.010 4 0,5 150 (130 - 170) 0,045 (0,025 - 0,065) 0,140 0,260 0 3,69 12.930 1.215 4 1,0 150 (130 - 170) 0,050 (0,030 - 0,070) 0,140 0,260 0 3,02 15.810 1.560 5 0,0 150 (130 - 170) 0,050 (0,030 - 0,070) 0,175 0,325 0 5,00 9.550 955 5 0,5 150 (130 - 170) 0,055 (0,035 - 0,075) 0,175 0,325 0 4,76 10.030 1.115 5 1,0 150 (130 - 170) 0,060 (0,040 - 0,080) 0,175 0,325 0 4,13 11.560 1.345 6 0,0 150 (130 - 170) 0,060 (0,040 - 0,080) 0,210 0,390 0 6,00 7.960 915 6 0,5 150 (130 - 170) 0,065 (0,045 - 0,085) 0,210 0,390 0 5,81 8.210 1.050 6 1,0 150 (130 - 170) 0,065 (0,045 - 0,085) 0,210 0,390 0 5,23 9.140 1.225 8 0,0 150 (130 - 170) 0,075 (0,055 - 0,095) 0,280 0,520 0 8,00 5.970 870 8 0,5 150 (130 - 170) 0,080 (0,060 - 0,100) 0,280 0,520 0 7,90 6.050 980 8 1,0 150 (130 - 170) 0,085 (0,065 - 0,105) 0,280 0,520 0 7,39 6.460 1.100 8 1,5 150 (130 - 170) 0,090 (0,070 - 0,110) 0,280 0,520 0 6,75 7.080 1.260 8 2,0 150 (130 - 170) 0,095 (0,075 - 0,115) 0,280 0,520 0 6,04 7.900 1.470 10 0,0 150 (130 - 170) 0,090 (0,070 - 0,110) 0,350 0,650 0 10,00 4.770 840 10 0,5 150 (130 - 170) 0,100 (0,080 - 0,120) 0,350 0,650 0 9,95 4.800 940 10 1,0 150 (130 - 170) 0,105 (0,085 - 0,125) 0,350 0,650 0 9,52 5.020 1.030 10 1,5 150 (130 - 170) 0,110 (0,090 - 0,130) 0,350 0,650 0 8,93 5.350 1.155 10 2,0 150 (130 - 170) 0,115 (0,095 - 0,135) 0,350 0,650 0 8,26 5.780 1.300 12 0,0 150 (130 - 170) 0,105 (0,085 - 0,125) 0,420 0,780 0 12,00 3.980 825 12 1,0 150 (130 - 170) 0,120 (0,100 - 0,140) 0,420 0,780 0 11,63 4.110 990 12 1,5 150 (130 - 170) 0,125 (0,105 - 0,145) 0,420 0,780 0 11,08 4.310 1.090 12 2,0 150 (130 - 170) 0,130 (0,110 - 0,150) 0,420 0,780 0 10,45 4.570 1.210 16 0,0 150 (130 - 170) 0,140 (0,120 - 0,160) 0,560 1,040 0 16,00 2.980 840 16 1,0 150 (130 - 170) 0,155 (0,135 - 0,175) 0,560 1,040 0 15,80 3.020 945 16 2,0 150 (130 - 170) 0,170 (0,150 - 0,190) 0,560 1,040 0 14,78 3.230 1.105 2 0,0 120 (108 - 132) 0,025 (0,005 - 0,045) 0,070 0,130 0 2,00 19.100 860 2 0,5 120 (108 - 132) 0,025 (0,005 - 0,045) 0,070 0,130 0 1,51 25.290 1.265 3 0,0 120 (110 - 130) 0,030 (0,010 - 0,050) 0,105 0,195 0 3,00 12.730 755 3 0,5 120 (110 - 130) 0,035 (0,015 - 0,055) 0,105 0,195 0 2,61 14.620 965 4 0,0 120 (110 - 130) 0,035 (0,015 - 0,055) 0,140 0,260 0 4,00 9.550 705 4 0,5 120 (110 - 130) 0,040 (0,020 - 0,060) 0,140 0,260 0 3,69 10.340 845 4 1,0 120 (110 - 130) 0,045 (0,025 - 0,065) 0,140 0,260 0 3,02 12.650 1.090 5 0,0 120 (110 - 130) 0,045 (0,025 - 0,065) 0,175 0,325 0 5,00 7.640 675 5 0,5 120 (110 - 130) 0,050 (0,030 - 0,070) 0,175 0,325 0 4,76 8.020 785 5 1,0 120 (110 - 130) 0,050 (0,030 - 0,070) 0,175 0,325 0 4,13 9.250 950 6 0,0 120 (110 - 130) 0,050 (0,030 - 0,070) 0,210 0,390 0 6,00 6.370 655 6 0,5 120 (110 - 130) 0,055 (0,035 - 0,075) 0,210 0,390 0 5,81 6.570 750 6 1,0 120 (110 - 130) 0,060 (0,040 - 0,080) 0,210 0,390 0 5,23 7.310 875 8 0,0 120 (110 - 130) 0,065 (0,045 - 0,085) 0,280 0,520 0 8,00 4.770 625 8 0,5 120 (110 - 130) 0,075 (0,055 - 0,095) 0,280 0,520 0 7,90 4.840 705 8 1,0 120 (110 - 130) 0,075 (0,055 - 0,095) 0,280 0,520 0 7,39 5.170 790 8 1,5 120 (110 - 130) 0,080 (0,060 - 0,100) 0,280 0,520 0 6,75 5.660 910 8 2,0 120 (110 - 130) 0,085 (0,065 - 0,105) 0,280 0,520 0 6,04 6.320 1.060 10 0,0 120 (110 - 130) 0,080 (0,060 - 0,100) 0,350 0,650 0 10,00 3.820 610 10 0,5 120 (110 - 130) 0,090 (0,070 - 0,110) 0,350 0,650 0 9,95 3.840 685 10 1,0 120 (110 - 130) 0,095 (0,075 - 0,115) 0,350 0,650 0 9,52 4.010 750 10 1,5 120 (110 - 130) 0,100 (0,080 - 0,120) 0,350 0,650 0 8,93 4.280 835 10 2,0 120 (110 - 130) 0,100 (0,080 - 0,120) 0,350 0,650 0 8,26 4.620 945 12 0,0 120 (110 - 130) 0,095 (0,075 - 0,115) 0,420 0,780 0 12,00 3.180 600 12 1,0 120 (110 - 130) 0,110 (0,090 - 0,130) 0,420 0,780 0 11,63 3.280 725 12 1,5 120 (110 - 130) 0,115 (0,095 - 0,135) 0,420 0,780 0 11,08 3.450 795 12 2,0 120 (110 - 130) 0,120 (0,100 - 0,140) 0,420 0,780 0 10,45 3.650 880 16 0,0 120 (110 - 130) 0,130 (0,110 - 0,150) 0,560 1,040 0 16,00 2.390 620 16 1,0 120 (110 - 130) 0,145 (0,125 - 0,165) 0,560 1,040 0 15,80 2.420 695 16 2,0 120 (110 - 130) 0,160 (0,140 - 0,180) 0,560 1,040 0 14,78 2.590 815 2 0,0 80 (70 - 90) 0,025 (0,005 - 0,045) 0,070 0,130 0 2,00 12.730 575 2 0,5 80 (70 - 90) 0,025 (0,005 - 0,045) 0,070 0,130 0 1,51 16.860 845 3 0,0 80 (70 - 90) 0,030 (0,010 - 0,050) 0,105 0,195 0 3,00 8.490 490 3 0,5 80 (70 - 90) 0,030 (0,010 - 0,050) 0,105 0,195 0 2,61 9.750 625 4 0,0 80 (70 - 90) 0,035 (0,015 - 0,055) 0,140 0,260 0 4,00 6.370 445 4 0,5 80 (70 - 90) 0,040 (0,020 - 0,060) 0,140 0,260 0 3,69 6.890 535 4 1,0 80 (70 - 90) 0,040 (0,020 - 0,060) 0,140 0,260 0 3,02 8.430 690 5 0,0 80 (70 - 90) 0,040 (0,020 - 0,060) 0,175 0,325 0 5,00 5.090 420 5 0,5 80 (70 - 90) 0,045 (0,025 - 0,065) 0,175 0,325 0 4,76 5.350 490 5 1,0 80 (70 - 90) 0,050 (0,030 - 0,070) 0,175 0,325 0 4,13 6.170 595 6 0,0 80 (70 - 90) 0,050 (0,030 - 0,070) 0,210 0,390 0 6,00 4.240 405 6 0,5 80 (70 - 90) 0,055 (0,035 - 0,075) 0,210 0,390 0 5,81 4.380 465 6 1,0 80 (70 - 90) 0,055 (0,035 - 0,075) 0,210 0,390 0 5,23 4.870 540 8 0,0 80 (70 - 90) 0,060 (0,040 - 0,080) 0,280 0,520 0 8,00 3.180 385 8 0,5 80 (70 - 90) 0,065 (0,045 - 0,085) 0,280 0,520 0 7,90 3.220 430 8 1,0 80 (70 - 90) 0,070 (0,050 - 0,090) 0,280 0,520 0 7,39 3.450 485 8 1,5 80 (70 - 90) 0,075 (0,055 - 0,095) 0,280 0,520 0 6,75 3.780 555 8 2,0 80 (70 - 90) 0,075 (0,055 - 0,095) 0,280 0,520 0 6,04 4.220 650 10 0,0 80 (70 - 90) 0,075 (0,055 - 0,095) 0,350 0,650 0 10,00 2.550 370 10 0,5 80 (70 - 90) 0,080 (0,060 - 0,100) 0,350 0,650 0 9,95 2.560 415 10 1,0 80 (70 - 90) 0,085 (0,065 - 0,105) 0,350 0,650 0 9,52 2.670 455 10 1,5 80 (70 - 90) 0,090 (0,070 - 0,110) 0,350 0,650 0 8,93 2.850 510 10 2,0 80 (70 - 90) 0,095 (0,075 - 0,115) 0,350 0,650 0 8,26 3.080 575 12 0,0 80 (70 - 90) 0,085 (0,065 - 0,105) 0,420 0,780 0 12,00 2.120 365 12 1,0 80 (70 - 90) 0,100 (0,080 - 0,120) 0,420 0,780 0 11,63 2.190 435 12 1,5 80 (70 - 90) 0,105 (0,085 - 0,125) 0,420 0,780 0 11,08 2.300 480 12 2,0 80 (70 - 90) 0,110 (0,090 - 0,130) 0,420 0,780 0 10,45 2.440 530 16 0,0 80 (70 - 90) 0,115 (0,095 - 0,135) 0,560 1,040 0 16,00 1.590 370 16 1,0 80 (70 - 90) 0,130 (0,110 - 0,150) 0,560 1,040 0 15,80 1.610 415 16 2,0 80 (70 - 90) 0,140 (0,120 - 0,160) 0,560 1,040 0 14,78 1.720 485 III-16
Schnittdatenempfehlung <strong>VHM</strong> 217 HX63 Parameters recommendation, Paramètres conseillés, Parametri di taglio indicativi Material Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 1200-1600 N/mm² 38-48 HRC Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 1200-1600 N/mm² 48-56 HRC Werkzeugstahl Vergütungsstahl Tool steel heat-treatable steel Acier à outil Acier par traitement thermique Acciaio per utensile Acciaio bonificato 56-63 HRC D [mm] R [mm] V c [m/min] f z [mm] a p [mm] a e [mm] β [°] ø-eff [mm] n [min -1 ] V f [mm/min] 2 0,0 360 (320 - 400) 0,040 (0,020 - 0,060) 0,100 0,100 45 2,00 57.300 4.640 2 0,5 360 (320 - 400) 0,045 (0,025 - 0,065) 0,100 0,100 45 1,99 57.590 5.180 3 0,0 360 (320 - 400) 0,055 (0,035 - 0,075) 0,115 0,115 45 3,00 38.200 4.330 3 0,5 360 (320 - 400) 0,065 (0,045 - 0,085) 0,115 0,115 45 3,00 38.250 4.820 4 0,0 360 (320 - 400) 0,075 (0,055 - 0,095) 0,130 0,130 45 4,00 28.650 4.175 4 0,5 360 (320 - 400) 0,080 (0,060 - 0,100) 0,130 0,130 45 4,00 28.650 4.640 4 1,0 360 (320 - 400) 0,085 (0,065 - 0,105) 0,130 0,130 45 3,93 29.160 4.960 5 0,0 360 (320 - 400) 0,090 (0,070 - 0,110) 0,150 0,150 45 5,00 22.920 4.085 5 0,5 360 (320 - 400) 0,100 (0,080 - 0,120) 0,150 0,150 45 5,00 22.920 4.535 5 1,0 360 (320 - 400) 0,105 (0,085 - 0,125) 0,150 0,150 45 4,95 23.170 4.815 6 0,0 360 (320 - 400) 0,105 (0,085 - 0,125) 0,165 0,165 45 6,00 19.100 4.020 6 0,5 360 (320 - 400) 0,115 (0,095 - 0,135) 0,165 0,165 45 6,00 19.100 4.470 6 1,0 360 (320 - 400) 0,125 (0,105 - 0,145) 0,165 0,165 45 5,96 19.230 4.725 8 0,0 360 (320 - 400) 0,140 (0,120 - 0,160) 0,195 0,195 45 8,00 14.320 3.945 8 0,5 360 (320 - 400) 0,155 (0,135 - 0,175) 0,195 0,195 45 7,99 14.340 4.385 8 1,0 360 (320 - 400) 0,160 (0,140 - 0,180) 0,195 0,195 45 7,98 14.360 4.615 8 1,5 360 (320 - 400) 0,170 (0,150 - 0,190) 0,195 0,195 45 7,89 14.520 4.885 8 2,0 360 (320 - 400) 0,175 (0,155 - 0,195) 0,195 0,195 45 7,77 14.740 5.190 10 0,0 360 (320 - 400) 0,170 (0,150 - 0,190) 0,230 0,230 45 10,00 11.460 3.900 10 0,5 360 (320 - 400) 0,190 (0,170 - 0,210) 0,230 0,230 45 9,98 11.480 4.340 10 1,0 360 (320 - 400) 0,200 (0,180 - 0,220) 0,230 0,230 45 9,99 11.470 4.550 10 1,5 360 (320 - 400) 0,210 (0,190 - 0,230) 0,230 0,230 45 9,92 11.550 4.800 10 2,0 360 (320 - 400) 0,215 (0,195 - 0,235) 0,230 0,230 45 9,82 11.670 5.075 12 0,0 360 (320 - 400) 0,205 (0,185 - 0,225) 0,260 0,260 45 12,00 9.550 3.865 12 1,0 360 (320 - 400) 0,235 (0,215 - 0,255) 0,260 0,260 45 12,00 9.550 4.510 12 1,5 360 (320 - 400) 0,250 (0,230 - 0,270) 0,260 0,260 45 11,95 9.590 4.745 12 2,0 360 (320 - 400) 0,260 (0,240 - 0,280) 0,260 0,260 45 11,86 9.670 5.000 16 0,0 360 (320 - 400) 0,280 (0,260 - 0,300) 0,465 0,465 45 16,00 7.160 4.020 16 1,0 360 (320 - 400) 0,310 (0,290 - 0,330) 0,465 0,465 45 15,95 7.180 4.480 16 2,0 360 (320 - 400) 0,340 (0,320 - 0,360) 0,675 0,675 45 15,99 7.170 4.895 2 0,0 250 (220 - 280) 0,040 (0,020 - 0,060) 0,100 0,100 45 2,00 39.790 3.225 2 0,5 250 (220 - 280) 0,045 (0,025 - 0,065) 0,100 0,100 45 1,99 39.990 3.600 3 0,0 250 (220 - 280) 0,055 (0,035 - 0,075) 0,115 0,115 45 3,00 26.530 2.960 3 0,5 250 (220 - 280) 0,060 (0,040 - 0,080) 0,115 0,115 45 3,00 26.560 3.295 4 0,0 250 (220 - 280) 0,070 (0,050 - 0,090) 0,130 0,130 45 4,00 19.890 2.830 4 0,5 250 (220 - 280) 0,080 (0,060 - 0,100) 0,130 0,130 45 4,00 19.900 3.145 4 1,0 250 (220 - 280) 0,085 (0,065 - 0,105) 0,130 0,130 45 3,93 20.250 3.360 5 0,0 250 (220 - 280) 0,085 (0,065 - 0,105) 0,150 0,150 45 5,00 15.920 2.750 5 0,5 250 (220 - 280) 0,095 (0,075 - 0,115) 0,150 0,150 45 5,00 15.920 3.055 5 1,0 250 (220 - 280) 0,100 (0,080 - 0,120) 0,150 0,150 45 4,95 16.090 3.245 6 0,0 250 (220 - 280) 0,100 (0,080 - 0,120) 0,165 0,165 45 6,00 13.260 2.700 6 0,5 250 (220 - 280) 0,115 (0,095 - 0,135) 0,165 0,165 45 6,00 13.270 3.000 6 1,0 250 (220 - 280) 0,120 (0,100 - 0,140) 0,165 0,165 45 5,96 13.360 3.170 8 0,0 250 (220 - 280) 0,130 (0,110 - 0,150) 0,195 0,195 45 8,00 9.950 2.630 8 0,5 250 (220 - 280) 0,145 (0,125 - 0,165) 0,195 0,195 45 7,99 9.960 2.925 8 1,0 250 (220 - 280) 0,155 (0,135 - 0,175) 0,195 0,195 45 7,98 9.970 3.080 8 1,5 250 (220 - 280) 0,160 (0,140 - 0,180) 0,195 0,195 45 7,89 10.080 3.260 8 2,0 250 (220 - 280) 0,170 (0,150 - 0,190) 0,195 0,195 45 7,77 10.240 3.460 10 0,0 250 (220 - 280) 0,165 (0,145 - 0,185) 0,230 0,230 45 10,00 7.960 2.595 10 0,5 250 (220 - 280) 0,180 (0,160 - 0,200) 0,230 0,230 45 9,98 7.980 2.885 10 1,0 250 (220 - 280) 0,190 (0,170 - 0,210) 0,230 0,230 45 9,99 7.970 3.025 10 1,5 250 (220 - 280) 0,200 (0,180 - 0,220) 0,230 0,230 45 9,92 8.020 3.195 10 2,0 250 (220 - 280) 0,210 (0,190 - 0,230) 0,230 0,230 45 9,82 8.110 3.375 12 0,0 250 (220 - 280) 0,195 (0,175 - 0,215) 0,260 0,260 45 12,00 6.630 2.565 12 1,0 250 (220 - 280) 0,225 (0,205 - 0,245) 0,260 0,260 45 12,00 6.630 2.995 12 1,5 250 (220 - 280) 0,235 (0,215 - 0,255) 0,260 0,260 45 11,95 6.660 3.150 12 2,0 250 (220 - 280) 0,245 (0,225 - 0,265) 0,260 0,260 45 11,86 6.710 3.320 16 0,0 250 (220 - 280) 0,265 (0,245 - 0,285) 0,465 0,465 45 16,00 4.970 2.660 16 1,0 250 (220 - 280) 0,295 (0,275 - 0,315) 0,465 0,465 45 15,95 4.990 2.965 16 2,0 250 (220 - 280) 0,325 (0,305 - 0,345) 0,675 0,675 45 15,99 4.980 3.240 2 0,0 180 (160 - 200) 0,035 (0,015 - 0,055) 0,100 0,100 45 2,00 28.650 2.065 2 0,5 180 (160 - 200) 0,040 (0,020 - 0,060) 0,100 0,100 45 1,99 28.790 2.305 3 0,0 180 (160 - 200) 0,050 (0,030 - 0,070) 0,115 0,115 45 3,00 19.100 1.910 3 0,5 180 (160 - 200) 0,055 (0,035 - 0,075) 0,115 0,115 45 3,00 19.120 2.120 4 0,0 180 (160 - 200) 0,065 (0,045 - 0,085) 0,130 0,130 45 4,00 14.320 1.830 4 0,5 180 (160 - 200) 0,070 (0,050 - 0,090) 0,130 0,130 45 4,00 14.330 2.035 4 1,0 180 (160 - 200) 0,075 (0,055 - 0,095) 0,130 0,130 45 3,93 14.580 2.175 5 0,0 180 (160 - 200) 0,080 (0,060 - 0,100) 0,150 0,150 45 5,00 11.460 1.785 5 0,5 180 (160 - 200) 0,085 (0,065 - 0,105) 0,150 0,150 45 5,00 11.460 1.980 5 1,0 180 (160 - 200) 0,090 (0,070 - 0,110) 0,150 0,150 45 4,95 11.590 2.105 6 0,0 180 (160 - 200) 0,090 (0,070 - 0,110) 0,165 0,165 45 6,00 9.550 1.755 6 0,5 180 (160 - 200) 0,100 (0,080 - 0,120) 0,165 0,165 45 6,00 9.550 1.950 6 1,0 180 (160 - 200) 0,105 (0,085 - 0,125) 0,165 0,165 45 5,96 9.620 2.060 8 0,0 180 (160 - 200) 0,120 (0,100 - 0,140) 0,195 0,195 45 8,00 7.160 1.715 8 0,5 180 (160 - 200) 0,135 (0,115 - 0,155) 0,195 0,195 45 7,99 7.170 1.905 8 1,0 180 (160 - 200) 0,140 (0,120 - 0,160) 0,195 0,195 45 7,98 7.180 2.005 8 1,5 180 (160 - 200) 0,145 (0,125 - 0,165) 0,195 0,195 45 7,89 7.260 2.125 8 2,0 180 (160 - 200) 0,155 (0,135 - 0,175) 0,195 0,195 45 7,77 7.370 2.255 10 0,0 180 (160 - 200) 0,150 (0,130 - 0,170) 0,230 0,230 45 10,00 5.730 1.690 10 0,5 180 (160 - 200) 0,165 (0,145 - 0,185) 0,230 0,230 45 9,98 5.740 1.885 10 1,0 180 (160 - 200) 0,170 (0,150 - 0,190) 0,230 0,230 45 9,99 5.730 1.975 10 1,5 180 (160 - 200) 0,180 (0,160 - 0,200) 0,230 0,230 45 9,92 5.770 2.085 10 2,0 180 (160 - 200) 0,190 (0,170 - 0,210) 0,230 0,230 45 9,82 5.840 2.200 12 0,0 180 (160 - 200) 0,175 (0,155 - 0,195) 0,260 0,260 45 12,00 4.770 1.675 12 1,0 180 (160 - 200) 0,205 (0,185 - 0,225) 0,260 0,260 45 12,00 4.780 1.955 12 1,5 180 (160 - 200) 0,215 (0,195 - 0,235) 0,260 0,260 45 11,95 4.800 2.055 12 2,0 180 (160 - 200) 0,225 (0,205 - 0,245) 0,260 0,260 45 11,86 4.830 2.165 16 0,0 180 (160 - 200) 0,245 (0,225 - 0,265) 0,465 0,465 45 16,00 3.580 1.740 16 1,0 180 (160 - 200) 0,270 (0,250 - 0,290) 0,465 0,465 45 15,95 3.590 1.940 16 2,0 180 (160 - 200) 0,295 (0,275 - 0,315) 0,675 0,675 45 15,99 3.580 2.115 III III-17
- Seite 1 und 2:
MILLING TOOLS MADE BY JONGEN
- Seite 3 und 4:
Firmenporträt Company Portrait, Po
- Seite 5 und 6:
Produktmatrix - Aluminiumbearbeitun
- Seite 7 und 8:
Produktmatrix - Bearbeitung von Sta
- Seite 9 und 10:
VHC-Fräser für trochoidale Bearbe
- Seite 11 und 12:
Produktmatrix - Microbearbeitung Pr
- Seite 13 und 14:
Produktmatrix - Graphitwerkzeuge Pr
- Seite 15 und 16:
Nachschleifservice / Sonderwerkzeug
- Seite 17 und 18:
VHM-Fräser für die Aluminium-, Ku
- Seite 19 und 20:
Schnittdatenempfehlung VHM 107 MK10
- Seite 21 und 22:
Schnittdatenempfehlung VHM 207 MK10
- Seite 23 und 24:
Schnittdatenempfehlung VHM 209 MK10
- Seite 25 und 26:
Schnittdatenempfehlung VHM 309 AL05
- Seite 27 und 28:
Schnittdatenempfehlung VHM 389 AL05
- Seite 29 und 30:
Schnittdatenempfehlung VHM 308W AL0
- Seite 31 und 32:
Schnittdatenempfehlung VHM 309 R AL
- Seite 33 und 34:
Schnittdatenempfehlung VHM 229 MK10
- Seite 35 und 36:
VHM-Fräser für die Stahl-, Edelst
- Seite 37 und 38:
Vollhartmetallfräser 281(W) TN12 S
- Seite 39 und 40:
Schnittdatenempfehlung VHM 281(W) T
- Seite 41 und 42:
Vollhartmetallfräser 282(W) TN12 S
- Seite 43 und 44:
Schnittdatenempfehlung VHM 282(W) T
- Seite 45 und 46:
Vollhartmetallfräser 381(W) TN12 S
- Seite 47 und 48:
Schnittdatenempfehlung VHM 381(W) T
- Seite 49 und 50:
Vollhartmetallfräser 382(W) TN12 S
- Seite 51 und 52:
Schnittdatenempfehlung VHM 382(W) T
- Seite 53 und 54:
Vollhartmetallfräser 481(W) TN12 S
- Seite 55 und 56:
Schnittdatenempfehlung VHM 481(W) T
- Seite 57 und 58:
Vollhartmetallfräser 482(W) TN12 S
- Seite 59 und 60:
Schnittdatenempfehlung VHM 482(W) T
- Seite 61 und 62:
Schnittdatenempfehlung VHM 487W TN1
- Seite 63 und 64:
Schnittdatenempfehlung VHM 471W Ti1
- Seite 65 und 66:
Schnittdatenempfehlung VHM 472W TS3
- Seite 67 und 68:
Schnittdatenempfehlung VHM 473W TS3
- Seite 69 und 70:
Vollhartmetallfräser 474W Ti10 Sol
- Seite 71 und 72:
Schnittdatenempfehlung VHM 474W Ti1
- Seite 73 und 74: Schnittdatenempfehlung VHM 474W TS3
- Seite 75 und 76: Schnittdatenempfehlung VHM 475W TS3
- Seite 77 und 78: Schnittdatenempfehlung VHM 476W TS3
- Seite 79 und 80: Schnittdatenempfehlung VHM 441W Ti0
- Seite 81 und 82: Schnittdatenempfehlung VHM 477W TS3
- Seite 83 und 84: Schnittdatenempfehlung VHM .46W TS3
- Seite 85 und 86: Schnittdatenempfehlung VHM .47W TS3
- Seite 87 und 88: Vollhartmetallfräser .48W TS35 Sol
- Seite 89 und 90: Schnittdatenempfehlung VHM .48W TS3
- Seite 91 und 92: Vollhartmetallfräser .49W TS35 Sol
- Seite 93 und 94: Schnittdatenempfehlung VHM .49W TS3
- Seite 95 und 96: Schnittdatenempfehlung VHM 451 HX63
- Seite 97 und 98: Schnittdatenempfehlung VHM 451 HX70
- Seite 99 und 100: Schnittdatenempfehlung VHM 643 Ti02
- Seite 101 und 102: Schnittdatenempfehlung VHM .54 HX63
- Seite 103 und 104: Schnittdatenempfehlung VHM .54 HX70
- Seite 105 und 106: Schnittdatenempfehlung VHM .55 HX63
- Seite 107 und 108: Schnittdatenempfehlung VHM .55 HX70
- Seite 109 und 110: VHM-Fräser für die 3D-Bearbeitung
- Seite 111 und 112: Schnittdatenempfehlung VHM 419 HX56
- Seite 113 und 114: Schnittdatenempfehlung VHM 420 HX56
- Seite 115 und 116: Vollhartmetallfräser 212 HX63 Soli
- Seite 117 und 118: Schnittdatenempfehlung VHM 212 HX63
- Seite 119 und 120: Vollhartmetallfräser 213 HX63 Soli
- Seite 121 und 122: Schnittdatenempfehlung VHM 213 HX63
- Seite 123: Vollhartmetallfräser 217 HX63 Soli
- Seite 127 und 128: III Vollhartmetallfräser 218 HX63
- Seite 129 und 130: Schnittdatenempfehlung VHM 218 HX63
- Seite 131 und 132: Vollhartmetallfräser 412 HX63 Soli
- Seite 133 und 134: Schnittdatenempfehlung VHM 412 HX63
- Seite 135 und 136: Vollhartmetallfräser 413 HX63 Soli
- Seite 137 und 138: Schnittdatenempfehlung VHM 413 HX63
- Seite 139 und 140: Vollhartmetallfräser 412 HX70 Soli
- Seite 141 und 142: Schnittdatenempfehlung VHM 412 HX70
- Seite 143 und 144: Vollhartmetallfräser 413 HX70 Soli
- Seite 145 und 146: Schnittdatenempfehlung VHM 413 HX70
- Seite 147 und 148: Vollhartmetallfräser 417 HX63 Soli
- Seite 149 und 150: Schnittdatenempfehlung VHM 417 HX63
- Seite 151 und 152: Vollhartmetallfräser 418 HX63 Soli
- Seite 153 und 154: Schnittdatenempfehlung VHM 418 HX63
- Seite 155 und 156: Vollhartmetallfräser 417 HX70 Soli
- Seite 157 und 158: Schnittdatenempfehlung VHM 417 HX70
- Seite 159 und 160: Vollhartmetallfräser 418 HX70 Soli
- Seite 161 und 162: Schnittdatenempfehlung VHM 418 HX70
- Seite 163 und 164: Schnittdatenempfehlung VHM 476W R T
- Seite 165 und 166: Schnittdatenempfehlung VHM 441W R T
- Seite 167 und 168: Schnittdatenempfehlung VHM 284(W) T
- Seite 169 und 170: Schnittdatenempfehlung VHM 285(W) T
- Seite 171 und 172: Schnittdatenempfehlung VHM 484(W) T
- Seite 173 und 174: Schnittdatenempfehlung VHM 485(W) T
- Seite 175 und 176:
Schnittdatenempfehlung VHM 236 HX63
- Seite 177 und 178:
Schnittdatenempfehlung VHM 237 HX63
- Seite 179 und 180:
Schnittdatenempfehlung VHM 236 HX70
- Seite 181 und 182:
Schnittdatenempfehlung VHM 237 HX70
- Seite 183 und 184:
Schnittdatenempfehlung VHM 238 HX63
- Seite 185 und 186:
Schnittdatenempfehlung VHM 239 HX63
- Seite 187 und 188:
Schnittdatenempfehlung VHM 238 HX70
- Seite 189 und 190:
Schnittdatenempfehlung VHM 239 HX70
- Seite 191 und 192:
VHC-Fräser für trochoidale Bearbe
- Seite 193 und 194:
Schnittdatenempfehlung VHC 516W Ti1
- Seite 195 und 196:
Schnittdatenempfehlung VHC 526W Ti0
- Seite 197 und 198:
Schnittdatenempfehlung VHC 555W Ti0
- Seite 199 und 200:
Schnittdatenempfehlung VHC 567W HX7
- Seite 201 und 202:
VHM-Fräser zum Fasen und Entgraten
- Seite 203 und 204:
Schnittdatenempfehlung VHM 460 Ti10
- Seite 205 und 206:
Schnittdatenempfehlung VHM 461 Ti10
- Seite 207 und 208:
Schnittdatenempfehlung VHM 461 Ti10
- Seite 209 und 210:
Schnittdatenempfehlung VHM 462 Ti10
- Seite 211 und 212:
VHM-Microfräser für die Stahl-, K
- Seite 213 und 214:
Microfräser Type MNF Micro solid c
- Seite 215 und 216:
Schnittdatenempfehlung Microfräser
- Seite 217 und 218:
Microfräser Type MNF Micro solid c
- Seite 219 und 220:
Schnittdatenempfehlung Microfräser
- Seite 221 und 222:
Schnittdatenempfehlung Microfräser
- Seite 223 und 224:
Schnittdatenempfehlung Microfräser
- Seite 225 und 226:
Microfräser Type MNT Micro solid c
- Seite 227 und 228:
Schnittdatenempfehlung Microfräser
- Seite 229 und 230:
Schnittdatenempfehlung Microfräser
- Seite 231 und 232:
Microfräser Type MKT Micro solid c
- Seite 233 und 234:
Schnittdatenempfehlung Microfräser
- Seite 235 und 236:
Schnittdatenempfehlung Microfräser
- Seite 237 und 238:
Microfräser Type MNK Micro solid c
- Seite 239 und 240:
Schnittdatenempfehlung Microfräser
- Seite 241 und 242:
Schnittdatenempfehlung Microfräser
- Seite 243 und 244:
Schnittdatenempfehlung Microfräser
- Seite 245 und 246:
Spezialfräser Solid carbide cutter
- Seite 247 und 248:
Schnittdatenempfehlung VHM 650W TS3
- Seite 249 und 250:
Produktmatrix - Graphitwerkzeuge Pr
- Seite 251 und 252:
Vollhartmetallfräser GDH 212 GD06
- Seite 253 und 254:
Schnittdatenempfehlung GDH 212 GD06
- Seite 255 und 256:
Vollhartmetallfräser GDH 213 GD06
- Seite 257 und 258:
Schnittdatenempfehlung GDH 213 GD06
- Seite 259 und 260:
Vollhartmetallfräser GDH 214 GD06
- Seite 261 und 262:
Schnittdatenempfehlung GDH 214 GD06
- Seite 263 und 264:
Vollhartmetallfräser GDH .74 GD06
- Seite 265 und 266:
Schnittdatenempfehlung GDH .74 GD06
- Seite 267 und 268:
Vollhartmetallfräser GDH .76 GD06
- Seite 269 und 270:
Schnittdatenempfehlung GDH .76 GD06
- Seite 271 und 272:
Vollhartmetallfräser GDH 222 GD06
- Seite 273 und 274:
Schnittdatenempfehlung GDH 222 GD06
- Seite 275 und 276:
Vollhartmetallfräser GDH 223 GD06
- Seite 277 und 278:
Schnittdatenempfehlung GDH 223 GD06
- Seite 279 und 280:
Vollhartmetallfräser GDH 227 GD06
- Seite 281 und 282:
Schnittdatenempfehlung GDH 227 GD06
- Seite 283 und 284:
Vollhartmetallfräser GDH 228 GD06
- Seite 285 und 286:
Schnittdatenempfehlung GDH 228 GD06
- Seite 287 und 288:
Vollhartmetallfräser GDH 230 GD06
- Seite 289 und 290:
Schnittdatenempfehlung GDH 230 GD06
- Seite 291 und 292:
Vollhartmetallfräser GDH 231 GD06
- Seite 293 und 294:
Schnittdatenempfehlung GDH 231 GD06
- Seite 295 und 296:
Vollhartmetallfräser GDH .24 GD06
- Seite 297 und 298:
Schnittdatenempfehlung GDH .24 GD06
- Seite 299 und 300:
Produktmatrix - Vollhartmetall-Bohr
- Seite 301 und 302:
Vollhartmetall-Bohrwerkzeuge Solid
- Seite 303 und 304:
Schnittdatenempfehlung Vollhartmeta
- Seite 305 und 306:
Abwicklung Jongen Nachschleifservic
- Seite 307 und 308:
Bestellformular Jongen Nachschleifs
- Seite 309 und 310:
Handling of the regrinding service
- Seite 311 und 312:
Regrinding order Please copy this s
- Seite 313 und 314:
Service de réaffûtage des fraises
- Seite 315 und 316:
Bon de commande pour une demande de
- Seite 317 und 318:
Servizio di riaffilatura per freset
- Seite 319 und 320:
Ordine di riaffilatura secondo lo s
- Seite 321 und 322:
Anfrage Sonderwerkzeug „Vollhartm
- Seite 323 und 324:
Inquiry-form JONGEN RAPID LINE - So
- Seite 325 und 326:
Formulaire pour demande d‘outils
- Seite 327 und 328:
Modulo per richiesta frese in metal
- Seite 329 und 330:
Technische Informationen Inhaltsver
- Seite 331 und 332:
Hartmetallqualitäten / Beschichtun
- Seite 333 und 334:
Symbolerklärung Kühlung Innenküh
- Seite 335 und 336:
Berechnungsformeln für die Zerspan
- Seite 337 und 338:
Oberflächenvergleichstabelle Oberf
- Seite 339 und 340:
Anwendungshinweise VHB-Bohrer Anboh
- Seite 341 und 342:
Werkstoffvergleichstabelle Deutschl
- Seite 343 und 344:
Werkstoffvergleichstabelle Deutschl
- Seite 345 und 346:
Werkstoffvergleichstabelle Deutschl
- Seite 347 und 348:
Technical appendix Index: Carbide t
- Seite 349 und 350:
Carbide Qualities / Coatings - Soli
- Seite 351 und 352:
Key to symbols Coolant Internal coo
- Seite 353 und 354:
Formulae RPM of spindle: 1000 ⋅ v
- Seite 355 und 356:
Surface comparison symbols Surface
- Seite 357 und 358:
Application instructions Solid Carb
- Seite 359 und 360:
Material comparison table Germany G
- Seite 361 und 362:
Material comparison table Germany G
- Seite 363 und 364:
Material comparison table Germany G
- Seite 365 und 366:
Support technique Sommaire: Nuances
- Seite 367 und 368:
Nuances de carbure Acier Fonte GG(G
- Seite 369 und 370:
Définition des symboles Lubrificat
- Seite 371 und 372:
Formule de calcul Vitesse de rotati
- Seite 373 und 374:
Tableau comparatif- État de surfac
- Seite 375 und 376:
Conseil d´utilisation des forets V
- Seite 377 und 378:
Tableau comparatif des matières Al
- Seite 379 und 380:
Tableau comparatif des matières Al
- Seite 381 und 382:
Tableau comparatif des matières Al
- Seite 383 und 384:
Guida tecnica Contenuto: Qualitá d
- Seite 385 und 386:
Qualitá di metallo duro / rivestim
- Seite 387 und 388:
Definizione simboli Refrigerazione
- Seite 389 und 390:
Formule tecniche per I calcoli dell
- Seite 391 und 392:
Tabella di conversione delle superf
- Seite 393 und 394:
Indicazioni per la programmazione -
- Seite 395 und 396:
Tabella di conversione dei material
- Seite 397 und 398:
Tabella di conversione dei material
- Seite 399 und 400:
Tabella di conversione dei material
- Seite 401 und 402:
General conditions of sale and deli
- Seite 403 und 404:
Condizioni Generali Di Vendita Le s