I Vollhartmetallfräser 207 MK10 Solid carbide cutters 207 MK10, Fraise carbure monobloc 207 MK10, Fresa a candela di metallo duro 207 MK10 Toleranz D ø3,0-16,0= -0,02 -0,04 30° DIN 6535-HA Bestell-Nr. Order-No., Référence, Codice D l d L Z <strong>VHM</strong> 207-03 MK10 3 7 3 38 2 <strong>VHM</strong> 207-04 MK10 4 8 4 50 2 <strong>VHM</strong> 207-05 MK10 5 10 5 50 2 <strong>VHM</strong> 207-06 MK10 6 10 6 58 2 <strong>VHM</strong> 207-08 MK10 8 16 8 64 2 <strong>VHM</strong> 207-10 MK10 10 20 10 73 2 <strong>VHM</strong> 207-12 MK10 12 24 12 84 2 <strong>VHM</strong> 207-14 MK10 14 28 14 84 2 <strong>VHM</strong> 207-16 MK10 16 34 16 93 2 I-4 Beim Bohren empfehlen wir den Zahnvorschub f z um 50% gegenüber Vollnuten zu reduzieren. For drilling operations, we recommend to reduce fz (feed speed per tooth) by 50% compared to full slot milling. Pour le perçage nous conseillons de réduire l´avance à la dent f z de 50% par rapport à un usinage en pleine matière. Effettuando lavorazioni in foratura si consiglia di ridurre l´avanzamento al dente (f z ) di ca. 50% in confronto alla lavorazione di scanalature in pieno.
Schnittdatenempfehlung <strong>VHM</strong> 207 MK10 Parameters recommendation, Paramètres conseillés, Parametri di taglio indicativi Material Aluminium langspanend Alu long chipping Alu copeaux longs Alluminio truciolo lungo Alu kurzspanend >6% Si Alu short chipping Alu copeaux courts Alluminio truciolo corto Alu Guss >10% Si Cast aluminium Fonte Alu Alluminio fuso CuZn Legierungen CuZn alloys Alliage CuZn Leghe CuZn Thermoplaste Thermoplastics Thermoplastique Termoplastica Material Aluminium langspanend Alu long chipping Alu copeaux longs Alluminio truciolo lungo Alu kurzspanend >6% Si Alu short chipping Alu copeaux courts Alluminio truciolo corto Alu Guss >10% Si Cast aluminium Fonte Alu Alluminio fuso CuZn Legierungen CuZn alloys Alliage CuZn Leghe CuZn Thermoplaste Thermoplastics Thermoplastique Termoplastica D V c f z a p a e n V f Q [mm] [m/min] [mm] [mm] [mm] [min-1] [mm/min] [cm3/min] 3 500 (460-560) 0,040 (0,030-0,050) 5,0 1,2 53.050 4.245 25,5 4 500 (460-560) 0,050 (0,040-0,060) 6,0 1,6 39.790 3.980 38,2 5 500 (460-560) 0,065 (0,055-0,075) 8,0 2,0 31.830 4.140 66,2 6 500 (460-560) 0,075 (0,065-0,085) 8,0 2,4 26.530 3.980 76,4 8 500 (460-560) 0,100 (0,090-0,110) 14,0 3,2 19.890 3.980 178,3 10 500 (460-560) 0,125 (0,100-0,150) 18,0 4,0 15.920 3.980 286,6 12 500 (460-560) 0,150 (0,140-0,160) 22,0 4,8 13.260 3.980 420,3 14 500 (460-560) 0,160 (0,140-0,180) 26,0 5,6 11.370 3.640 530,0 16 500 (460-560) 0,180 (0,160-0,200) 32,0 6,4 9.950 3.580 733,2 3 480 (400-520) 0,040 (0,030-0,050) 5,0 1,2 50.930 4.075 24,5 4 480 (400-520) 0,050 (0,040-0,060) 6,0 1,6 38.200 3.820 36,7 5 480 (400-520) 0,065 (0,055-0,075) 8,0 2,0 30.560 3.975 63,6 6 480 (400-520) 0,075 (0,065-0,085) 8,0 2,4 25.460 3.820 73,3 8 480 (400-520) 0,100 (0,090-0,110) 14,0 3,2 19.100 3.820 171,1 10 480 (400-520) 0,125 (0,100-0,150) 18,0 4,0 15.280 3.820 275,0 12 480 (400-520) 0,150 (0,140-0,160) 22,0 4,8 12.730 3.820 403,4 14 480 (460-560) 0,160 (0,140-0,180) 26,0 5,6 10.910 3.490 508,1 16 480 (460-560) 0,180 (0,160-0,200) 32,0 6,4 9.550 3.440 704,5 3 250 (200-300) 0,040 (0,030-0,050) 5,0 1,2 26.530 2.120 12,7 4 250 (200-300) 0,050 (0,040-0,060) 6,0 1,6 19.890 1.990 19,1 5 250 (200-300) 0,065 (0,055-0,075) 8,0 2,0 15.920 2.070 33,1 6 250 (200-300) 0,075 (0,065-0,085) 8,0 2,4 13.260 1.990 38,2 8 250 (200-300) 0,100 (0,090-0,110) 14,0 3,2 9.950 1.990 89,2 10 250 (200-300) 0,125 (0,100-0,150) 18,0 4,0 7.960 1.990 143,3 12 250 (200-300) 0,150 (0,140-0,160) 22,0 4,8 6.630 1.990 210,1 14 250 (200-300) 0,160 (0,140-0,180) 26,0 5,6 5.680 1.820 265,0 16 250 (200-300) 0,180 (0,160-0,200) 32,0 6,4 4.970 1.790 366,6 3 270 (230-300) 0,040 (0,030-0,050) 5,0 1,2 28.650 2.290 13,7 4 270 (230-300) 0,050 (0,040-0,060) 6,0 1,6 21.490 2.150 20,6 5 270 (230-300) 0,065 (0,055-0,075) 8,0 2,0 17.190 2.235 35,8 6 270 (230-300) 0,075 (0,065-0,085) 8,0 2,4 14.320 2.150 41,3 8 270 (230-300) 0,100 (0,090-0,110) 14,0 3,2 10.740 2.150 96,3 10 270 (230-300) 0,125 (0,100-0,150) 18,0 4,0 8.590 2.150 154,8 12 270 (230-300) 0,150 (0,140-0,160) 22,0 4,8 7.160 2.150 227,0 14 270 (230-300) 0,160 (0,140-0,180) 26,0 5,6 6.140 1.965 286,1 16 270 (230-300) 0,180 (0,160-0,200) 32,0 6,4 5.370 1.935 396,3 3 1.200 (1.100-1.300) 0,040 (0,030-0,050) 5,0 1,2 127.320 10.185 61,1 4 1.200 (1.100-1.300) 0,050 (0,040-0,060) 6,0 1,6 95.490 9.550 91,7 5 1.200 (1.100-1.300) 0,065 (0,055-0,075) 8,0 2,0 76.390 9.930 158,9 6 1.200 (1.100-1.300) 0,075 (0,065-0,085) 8,0 2,4 63.660 9.550 183,4 8 1.200 (1.100-1.300) 0,100 (0,090-0,110) 14,0 3,2 47.750 9.550 427,8 10 1.200 (1.100-1.300) 0,125 (0,100-0,150) 18,0 4,0 38.200 9.550 687,6 12 1.200 (1.100-1.300) 0,150 (0,140-0,160) 22,0 4,8 31.830 9.550 1.008,5 14 1.200 (1.100-1.300) 0,160 (0,140-0,180) 26,0 5,6 27.280 8.730 1.271,1 16 1.200 (1.100-1.300) 0,180 (0,160-0,200) 32,0 6,4 23.870 8.595 1.760,3 D V c f z a p a e n V f Q [mm] [m/min] [mm] [mm] [mm] [min-1] [mm/min] [cm3/min] 3 500 (460-560) 0,015 (0,010-0,030) 1,5 3,0 53.050 1.590 7,2 4 500 (460-560) 0,020 (0,010-0,050) 2,0 4,0 39.790 1.590 12,7 5 500 (460-560) 0,035 (0,020-0,050) 2,5 5,0 31.830 2.230 27,9 6 500 (460-560) 0,050 (0,030-0,060) 3,0 6,0 26.530 2.655 47,8 8 500 (460-560) 0,060 (0,040-0,070) 4,0 8,0 19.890 2.385 76,3 10 500 (460-560) 0,080 (0,060-0,100) 5,0 10,0 15.920 2.545 127,3 12 500 (460-560) 0,100 (0,080-0,120) 6,0 12,0 13.260 2.650 190,8 14 500 (460-560) 0,120 (0,100-0,140) 7,0 14,0 11.370 2.730 267,5 16 500 (460-560) 0,140 (0,120-0,160) 8,0 16,0 9.950 2.785 356,5 3 480 (400-520) 0,040 (0,010-0,030) 1,5 3,0 50.930 4.075 18,3 4 480 (400-520) 0,050 (0,010-0,050) 2,0 4,0 38.200 3.820 30,6 5 480 (400-520) 0,065 (0,020-0,050) 2,5 5,0 30.560 3.975 49,7 6 480 (400-520) 0,075 (0,030-0,060) 3,0 6,0 25.460 3.820 68,8 8 480 (400-520) 0,100 (0,040-0,070) 4,0 8,0 19.100 3.820 122,2 10 480 (400-520) 0,125 (0,060-0,100) 5,0 10,0 15.280 3.820 191,0 12 480 (400-520) 0,150 (0,080-0,120) 6,0 12,0 12.730 3.820 275,0 14 480 (460-560) 0,160 (0,100-0,140) 7,0 14,0 10.910 3.490 342,0 16 480 (460-560) 0,180 (0,120-0,160) 8,0 16,0 9.550 3.440 440,3 3 250 (200-300) 0,040 (0,010-0,030) 1,5 3,0 26.530 2.120 9,5 4 250 (200-300) 0,050 (0,010-0,050) 2,0 4,0 19.890 1.990 15,9 5 250 (200-300) 0,065 (0,020-0,050) 2,5 5,0 15.920 2.070 25,9 6 250 (200-300) 0,075 (0,030-0,060) 3,0 6,0 13.260 1.990 35,8 8 250 (200-300) 0,100 (0,040-0,070) 4,0 8,0 9.950 1.990 63,7 10 250 (200-300) 0,125 (0,060-0,100) 5,0 10,0 7.960 1.990 99,5 12 250 (200-300) 0,150 (0,080-0,120) 6,0 12,0 6.630 1.990 143,3 14 250 (200-300) 0,160 (0,100-0,140) 7,0 14,0 5.680 1.820 178,4 16 250 (200-300) 0,180 (0,120-0,160) 8,0 16,0 4.970 1.790 229,1 3 270 (230-300) 0,040 (0,010-0,030) 1,5 3,0 28.650 2.290 10,3 4 270 (230-300) 0,050 (0,010-0,050) 2,0 4,0 21.490 2.150 17,2 5 270 (230-300) 0,065 (0,020-0,050) 2,5 5,0 17.190 2.235 27,9 6 270 (230-300) 0,075 (0,030-0,060) 3,0 6,0 14.320 2.150 38,7 8 270 (230-300) 0,100 (0,040-0,070) 4,0 8,0 10.740 2.150 68,8 10 270 (230-300) 0,125 (0,060-0,100) 5,0 10,0 8.590 2.150 107,5 12 270 (230-300) 0,150 (0,080-0,120) 6,0 12,0 7.160 2.150 154,8 14 270 (230-300) 0,160 (0,100-0,140) 7,0 14,0 6.140 1.965 192,6 16 270 (230-300) 0,180 (0,120-0,160) 8,0 16,0 5.370 1.935 247,7 3 1.200 (1.100-1.300) 0,040 (0,010-0,030) 1,5 3,0 127.320 10.185 45,8 4 1.200 (1.100-1.300) 0,050 (0,010-0,050) 2,0 4,0 95.490 9.550 76,4 5 1.200 (1.100-1.300) 0,065 (0,020-0,050) 2,5 5,0 76.390 9.930 124,1 6 1.200 (1.100-1.300) 0,075 (0,030-0,060) 3,0 6,0 63.660 9.550 171,9 8 1.200 (1.100-1.300) 0,100 (0,040-0,070) 4,0 8,0 47.750 9.550 305,6 10 1.200 (1.100-1.300) 0,125 (0,060-0,100) 5,0 10,0 38.200 9.550 477,5 12 1.200 (1.100-1.300) 0,150 (0,080-0,120) 6,0 12,0 31.830 9.550 687,6 14 1.200 (1.100-1.300) 0,160 (0,100-0,140) 7,0 14,0 27.280 8.730 855,5 16 1.200 (1.100-1.300) 0,180 (0,120-0,160) 8,0 16,0 23.870 8.595 1.100,2 I I-5
- Seite 1 und 2: MILLING TOOLS MADE BY JONGEN
- Seite 3 und 4: Firmenporträt Company Portrait, Po
- Seite 5 und 6: Produktmatrix - Aluminiumbearbeitun
- Seite 7 und 8: Produktmatrix - Bearbeitung von Sta
- Seite 9 und 10: VHC-Fräser für trochoidale Bearbe
- Seite 11 und 12: Produktmatrix - Microbearbeitung Pr
- Seite 13 und 14: Produktmatrix - Graphitwerkzeuge Pr
- Seite 15 und 16: Nachschleifservice / Sonderwerkzeug
- Seite 17 und 18: VHM-Fräser für die Aluminium-, Ku
- Seite 19: Schnittdatenempfehlung VHM 107 MK10
- Seite 23 und 24: Schnittdatenempfehlung VHM 209 MK10
- Seite 25 und 26: Schnittdatenempfehlung VHM 309 AL05
- Seite 27 und 28: Schnittdatenempfehlung VHM 389 AL05
- Seite 29 und 30: Schnittdatenempfehlung VHM 308W AL0
- Seite 31 und 32: Schnittdatenempfehlung VHM 309 R AL
- Seite 33 und 34: Schnittdatenempfehlung VHM 229 MK10
- Seite 35 und 36: VHM-Fräser für die Stahl-, Edelst
- Seite 37 und 38: Vollhartmetallfräser 281(W) TN12 S
- Seite 39 und 40: Schnittdatenempfehlung VHM 281(W) T
- Seite 41 und 42: Vollhartmetallfräser 282(W) TN12 S
- Seite 43 und 44: Schnittdatenempfehlung VHM 282(W) T
- Seite 45 und 46: Vollhartmetallfräser 381(W) TN12 S
- Seite 47 und 48: Schnittdatenempfehlung VHM 381(W) T
- Seite 49 und 50: Vollhartmetallfräser 382(W) TN12 S
- Seite 51 und 52: Schnittdatenempfehlung VHM 382(W) T
- Seite 53 und 54: Vollhartmetallfräser 481(W) TN12 S
- Seite 55 und 56: Schnittdatenempfehlung VHM 481(W) T
- Seite 57 und 58: Vollhartmetallfräser 482(W) TN12 S
- Seite 59 und 60: Schnittdatenempfehlung VHM 482(W) T
- Seite 61 und 62: Schnittdatenempfehlung VHM 487W TN1
- Seite 63 und 64: Schnittdatenempfehlung VHM 471W Ti1
- Seite 65 und 66: Schnittdatenempfehlung VHM 472W TS3
- Seite 67 und 68: Schnittdatenempfehlung VHM 473W TS3
- Seite 69 und 70: Vollhartmetallfräser 474W Ti10 Sol
- Seite 71 und 72:
Schnittdatenempfehlung VHM 474W Ti1
- Seite 73 und 74:
Schnittdatenempfehlung VHM 474W TS3
- Seite 75 und 76:
Schnittdatenempfehlung VHM 475W TS3
- Seite 77 und 78:
Schnittdatenempfehlung VHM 476W TS3
- Seite 79 und 80:
Schnittdatenempfehlung VHM 441W Ti0
- Seite 81 und 82:
Schnittdatenempfehlung VHM 477W TS3
- Seite 83 und 84:
Schnittdatenempfehlung VHM .46W TS3
- Seite 85 und 86:
Schnittdatenempfehlung VHM .47W TS3
- Seite 87 und 88:
Vollhartmetallfräser .48W TS35 Sol
- Seite 89 und 90:
Schnittdatenempfehlung VHM .48W TS3
- Seite 91 und 92:
Vollhartmetallfräser .49W TS35 Sol
- Seite 93 und 94:
Schnittdatenempfehlung VHM .49W TS3
- Seite 95 und 96:
Schnittdatenempfehlung VHM 451 HX63
- Seite 97 und 98:
Schnittdatenempfehlung VHM 451 HX70
- Seite 99 und 100:
Schnittdatenempfehlung VHM 643 Ti02
- Seite 101 und 102:
Schnittdatenempfehlung VHM .54 HX63
- Seite 103 und 104:
Schnittdatenempfehlung VHM .54 HX70
- Seite 105 und 106:
Schnittdatenempfehlung VHM .55 HX63
- Seite 107 und 108:
Schnittdatenempfehlung VHM .55 HX70
- Seite 109 und 110:
VHM-Fräser für die 3D-Bearbeitung
- Seite 111 und 112:
Schnittdatenempfehlung VHM 419 HX56
- Seite 113 und 114:
Schnittdatenempfehlung VHM 420 HX56
- Seite 115 und 116:
Vollhartmetallfräser 212 HX63 Soli
- Seite 117 und 118:
Schnittdatenempfehlung VHM 212 HX63
- Seite 119 und 120:
Vollhartmetallfräser 213 HX63 Soli
- Seite 121 und 122:
Schnittdatenempfehlung VHM 213 HX63
- Seite 123 und 124:
Vollhartmetallfräser 217 HX63 Soli
- Seite 125 und 126:
Schnittdatenempfehlung VHM 217 HX63
- Seite 127 und 128:
III Vollhartmetallfräser 218 HX63
- Seite 129 und 130:
Schnittdatenempfehlung VHM 218 HX63
- Seite 131 und 132:
Vollhartmetallfräser 412 HX63 Soli
- Seite 133 und 134:
Schnittdatenempfehlung VHM 412 HX63
- Seite 135 und 136:
Vollhartmetallfräser 413 HX63 Soli
- Seite 137 und 138:
Schnittdatenempfehlung VHM 413 HX63
- Seite 139 und 140:
Vollhartmetallfräser 412 HX70 Soli
- Seite 141 und 142:
Schnittdatenempfehlung VHM 412 HX70
- Seite 143 und 144:
Vollhartmetallfräser 413 HX70 Soli
- Seite 145 und 146:
Schnittdatenempfehlung VHM 413 HX70
- Seite 147 und 148:
Vollhartmetallfräser 417 HX63 Soli
- Seite 149 und 150:
Schnittdatenempfehlung VHM 417 HX63
- Seite 151 und 152:
Vollhartmetallfräser 418 HX63 Soli
- Seite 153 und 154:
Schnittdatenempfehlung VHM 418 HX63
- Seite 155 und 156:
Vollhartmetallfräser 417 HX70 Soli
- Seite 157 und 158:
Schnittdatenempfehlung VHM 417 HX70
- Seite 159 und 160:
Vollhartmetallfräser 418 HX70 Soli
- Seite 161 und 162:
Schnittdatenempfehlung VHM 418 HX70
- Seite 163 und 164:
Schnittdatenempfehlung VHM 476W R T
- Seite 165 und 166:
Schnittdatenempfehlung VHM 441W R T
- Seite 167 und 168:
Schnittdatenempfehlung VHM 284(W) T
- Seite 169 und 170:
Schnittdatenempfehlung VHM 285(W) T
- Seite 171 und 172:
Schnittdatenempfehlung VHM 484(W) T
- Seite 173 und 174:
Schnittdatenempfehlung VHM 485(W) T
- Seite 175 und 176:
Schnittdatenempfehlung VHM 236 HX63
- Seite 177 und 178:
Schnittdatenempfehlung VHM 237 HX63
- Seite 179 und 180:
Schnittdatenempfehlung VHM 236 HX70
- Seite 181 und 182:
Schnittdatenempfehlung VHM 237 HX70
- Seite 183 und 184:
Schnittdatenempfehlung VHM 238 HX63
- Seite 185 und 186:
Schnittdatenempfehlung VHM 239 HX63
- Seite 187 und 188:
Schnittdatenempfehlung VHM 238 HX70
- Seite 189 und 190:
Schnittdatenempfehlung VHM 239 HX70
- Seite 191 und 192:
VHC-Fräser für trochoidale Bearbe
- Seite 193 und 194:
Schnittdatenempfehlung VHC 516W Ti1
- Seite 195 und 196:
Schnittdatenempfehlung VHC 526W Ti0
- Seite 197 und 198:
Schnittdatenempfehlung VHC 555W Ti0
- Seite 199 und 200:
Schnittdatenempfehlung VHC 567W HX7
- Seite 201 und 202:
VHM-Fräser zum Fasen und Entgraten
- Seite 203 und 204:
Schnittdatenempfehlung VHM 460 Ti10
- Seite 205 und 206:
Schnittdatenempfehlung VHM 461 Ti10
- Seite 207 und 208:
Schnittdatenempfehlung VHM 461 Ti10
- Seite 209 und 210:
Schnittdatenempfehlung VHM 462 Ti10
- Seite 211 und 212:
VHM-Microfräser für die Stahl-, K
- Seite 213 und 214:
Microfräser Type MNF Micro solid c
- Seite 215 und 216:
Schnittdatenempfehlung Microfräser
- Seite 217 und 218:
Microfräser Type MNF Micro solid c
- Seite 219 und 220:
Schnittdatenempfehlung Microfräser
- Seite 221 und 222:
Schnittdatenempfehlung Microfräser
- Seite 223 und 224:
Schnittdatenempfehlung Microfräser
- Seite 225 und 226:
Microfräser Type MNT Micro solid c
- Seite 227 und 228:
Schnittdatenempfehlung Microfräser
- Seite 229 und 230:
Schnittdatenempfehlung Microfräser
- Seite 231 und 232:
Microfräser Type MKT Micro solid c
- Seite 233 und 234:
Schnittdatenempfehlung Microfräser
- Seite 235 und 236:
Schnittdatenempfehlung Microfräser
- Seite 237 und 238:
Microfräser Type MNK Micro solid c
- Seite 239 und 240:
Schnittdatenempfehlung Microfräser
- Seite 241 und 242:
Schnittdatenempfehlung Microfräser
- Seite 243 und 244:
Schnittdatenempfehlung Microfräser
- Seite 245 und 246:
Spezialfräser Solid carbide cutter
- Seite 247 und 248:
Schnittdatenempfehlung VHM 650W TS3
- Seite 249 und 250:
Produktmatrix - Graphitwerkzeuge Pr
- Seite 251 und 252:
Vollhartmetallfräser GDH 212 GD06
- Seite 253 und 254:
Schnittdatenempfehlung GDH 212 GD06
- Seite 255 und 256:
Vollhartmetallfräser GDH 213 GD06
- Seite 257 und 258:
Schnittdatenempfehlung GDH 213 GD06
- Seite 259 und 260:
Vollhartmetallfräser GDH 214 GD06
- Seite 261 und 262:
Schnittdatenempfehlung GDH 214 GD06
- Seite 263 und 264:
Vollhartmetallfräser GDH .74 GD06
- Seite 265 und 266:
Schnittdatenempfehlung GDH .74 GD06
- Seite 267 und 268:
Vollhartmetallfräser GDH .76 GD06
- Seite 269 und 270:
Schnittdatenempfehlung GDH .76 GD06
- Seite 271 und 272:
Vollhartmetallfräser GDH 222 GD06
- Seite 273 und 274:
Schnittdatenempfehlung GDH 222 GD06
- Seite 275 und 276:
Vollhartmetallfräser GDH 223 GD06
- Seite 277 und 278:
Schnittdatenempfehlung GDH 223 GD06
- Seite 279 und 280:
Vollhartmetallfräser GDH 227 GD06
- Seite 281 und 282:
Schnittdatenempfehlung GDH 227 GD06
- Seite 283 und 284:
Vollhartmetallfräser GDH 228 GD06
- Seite 285 und 286:
Schnittdatenempfehlung GDH 228 GD06
- Seite 287 und 288:
Vollhartmetallfräser GDH 230 GD06
- Seite 289 und 290:
Schnittdatenempfehlung GDH 230 GD06
- Seite 291 und 292:
Vollhartmetallfräser GDH 231 GD06
- Seite 293 und 294:
Schnittdatenempfehlung GDH 231 GD06
- Seite 295 und 296:
Vollhartmetallfräser GDH .24 GD06
- Seite 297 und 298:
Schnittdatenempfehlung GDH .24 GD06
- Seite 299 und 300:
Produktmatrix - Vollhartmetall-Bohr
- Seite 301 und 302:
Vollhartmetall-Bohrwerkzeuge Solid
- Seite 303 und 304:
Schnittdatenempfehlung Vollhartmeta
- Seite 305 und 306:
Abwicklung Jongen Nachschleifservic
- Seite 307 und 308:
Bestellformular Jongen Nachschleifs
- Seite 309 und 310:
Handling of the regrinding service
- Seite 311 und 312:
Regrinding order Please copy this s
- Seite 313 und 314:
Service de réaffûtage des fraises
- Seite 315 und 316:
Bon de commande pour une demande de
- Seite 317 und 318:
Servizio di riaffilatura per freset
- Seite 319 und 320:
Ordine di riaffilatura secondo lo s
- Seite 321 und 322:
Anfrage Sonderwerkzeug „Vollhartm
- Seite 323 und 324:
Inquiry-form JONGEN RAPID LINE - So
- Seite 325 und 326:
Formulaire pour demande d‘outils
- Seite 327 und 328:
Modulo per richiesta frese in metal
- Seite 329 und 330:
Technische Informationen Inhaltsver
- Seite 331 und 332:
Hartmetallqualitäten / Beschichtun
- Seite 333 und 334:
Symbolerklärung Kühlung Innenküh
- Seite 335 und 336:
Berechnungsformeln für die Zerspan
- Seite 337 und 338:
Oberflächenvergleichstabelle Oberf
- Seite 339 und 340:
Anwendungshinweise VHB-Bohrer Anboh
- Seite 341 und 342:
Werkstoffvergleichstabelle Deutschl
- Seite 343 und 344:
Werkstoffvergleichstabelle Deutschl
- Seite 345 und 346:
Werkstoffvergleichstabelle Deutschl
- Seite 347 und 348:
Technical appendix Index: Carbide t
- Seite 349 und 350:
Carbide Qualities / Coatings - Soli
- Seite 351 und 352:
Key to symbols Coolant Internal coo
- Seite 353 und 354:
Formulae RPM of spindle: 1000 ⋅ v
- Seite 355 und 356:
Surface comparison symbols Surface
- Seite 357 und 358:
Application instructions Solid Carb
- Seite 359 und 360:
Material comparison table Germany G
- Seite 361 und 362:
Material comparison table Germany G
- Seite 363 und 364:
Material comparison table Germany G
- Seite 365 und 366:
Support technique Sommaire: Nuances
- Seite 367 und 368:
Nuances de carbure Acier Fonte GG(G
- Seite 369 und 370:
Définition des symboles Lubrificat
- Seite 371 und 372:
Formule de calcul Vitesse de rotati
- Seite 373 und 374:
Tableau comparatif- État de surfac
- Seite 375 und 376:
Conseil d´utilisation des forets V
- Seite 377 und 378:
Tableau comparatif des matières Al
- Seite 379 und 380:
Tableau comparatif des matières Al
- Seite 381 und 382:
Tableau comparatif des matières Al
- Seite 383 und 384:
Guida tecnica Contenuto: Qualitá d
- Seite 385 und 386:
Qualitá di metallo duro / rivestim
- Seite 387 und 388:
Definizione simboli Refrigerazione
- Seite 389 und 390:
Formule tecniche per I calcoli dell
- Seite 391 und 392:
Tabella di conversione delle superf
- Seite 393 und 394:
Indicazioni per la programmazione -
- Seite 395 und 396:
Tabella di conversione dei material
- Seite 397 und 398:
Tabella di conversione dei material
- Seite 399 und 400:
Tabella di conversione dei material
- Seite 401 und 402:
General conditions of sale and deli
- Seite 403 und 404:
Condizioni Generali Di Vendita Le s